GE/PNH-45/2020-21

Amount

Schedule 'A' Part-I (Building Work) JOB NO. SHQ/POONCH /REV-09/2019-20 (FOL shed block)

Total amount of Sch 'A' Part-I (Building work) brought forward from srl page No-19.

Schedule 'A'Part-II(Demolition Works) JOB NO. SHQ/POONCH/MINOR-09/2020-21 (Demolition work against BLDG No T-07(Nishan Hut)

Total amount of Sch 'A' Part-II(Demolition work) brought forward from srl page No-20

Schedule 'A'Part-III (Misc Items of Works) Note : This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col. 5 siginifies this fact only.(JOB NO. SHQ/POONCH/SR/Bldg/07/2020-21 (Spl rep to bldg No P-27 at Poonch) & JOB NO. SHQ/POONCH/MINOR/08/2020-21 (SProvn of one Garbage bin near Bldg No T-23 at Gulpur) )

B&R PORTION:- Taking down cement plaster of any description on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc.complete all as specified.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) any thickness including cover fillets all as specified & directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5Sqm and not exceeding 4Sqm each, complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5Sqm each, complete all as specified.

Taking down shutters of any description exceeding 1sqm and not exceeding 2sqm each, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified.

Demolition of brick or stone masonry, built in lime mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

15mm thick rendering in CM 1:6 on other than fair faces of brick or stone masonry surfaces & finishing the surface even and smooth without using extra cement, complete all as specified.

Preparation of newly plastered surface of wall including cornices pilaster etc, and applying two coats of oil bound distemper over and including 1-2mm thick wall care putty, complete as specified and directed.

Applying two coats of white wash including preparation of old treated plastered surfaces of wall complete all as specified.

Preparation of old plastered or un plastered wall surfaces including washing, scrubbing down and stopping of distermperd surfaces and applying one coat of oil bound distemper, complete all as specified.

Vitrified ceramic tiles 10 mm thick (square / rectangular) area of each tile not exceeding 0.36sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

Non skid coloured ceramic tiles 7 to 8mm thick area of each tile exc 0.11Sqm but n exc. 0.18Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

Glazed ceramic coloured tiles (350x250mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, valley gutter, ridge & similar works fixed with self tapping screws complete all as specified.

Suspended false ceiling using E- grid suspended ceiling grid system of grid size 600x600mm with GI frame work of main runner 38 x 24mm sheet thickness 0.4mm, cross Tee 28 x 24mm sheet thickness 0.3mm and wall angle 24 x 24mm x 0.5mm using 4mm thick high pressure stream cured classic variant E-board, designer pattern (ISI marked, IS No 14862-2000) & E board to be placed in the grid suspended by 4mm GI wire hangers from the purlins of the roof with butter fly clips with & including two coats of synthetic enamel paint, complete all as specified and directed. Make:- Everest Industries Ltd or equivalent as approved by GE.

Walling of random rubble stone masonry brought upto course, well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed.

Description all as per item No. 23 above, but except stone complete all as specified and directed.

Raking out joints / pointing to random rubble or polygonal rubble uncoursed or brought up to courses build in cement mortar, complete all as specified and directed.

Raised pointing to random rubble masonary, or polygonal rubble, uncoarsed or brought upto courses in cement mortar 1:3, complete all as specified and directed.

Factory made Pressed steel frames of size 125x60mm made out of PBI sheet 1.25 mm thick for doors with one or more rebates including necessary fixing lugs, hinge,lock strike plate etc.complete including bottom of each chowkat to be welded with 02 nos 25x25x3mm thick angle iron projecting 10cm on either side & PCC 1:3:6 type C0 in back filling of chowkats & tarring back of chowkats and holdfasts complete all as specified & directed.

Factory made Pressed steel frames of size 105x60mm made out of PBI sheet 1.25 mm thick for doors with one or more rebates including necessary fixing lugs, hinge,lock strike plate etc.complete including bottom of each chowkat to be welded with 02 Nos 25x25x3mm thick angle iron projecting 10cm on either side & PCC 1:3:6 type C-0 in back filling of chowkats & tarring back of chowkats and holdfasts complete all as specified & directed.

35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides and covered with decorative face veneer with lipping/frame to match, complete all as specified and directed.

35mm thick 2nd class hard wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete, all as specified.

18-19mm prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified.

Supply and fixing factory made solid core PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet, 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified & shown in relevant drawing of item No. 08080 in MES Schedule (Part-II) and directed by Engineer-in-Charge.

Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified.

Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, complete all as specified.

Steel windows or ventilators, fixed type, with glazing bars complete all as specified.

Mild steel work conforming to Fe-290 (Gde E-165) as in grills, gratings etc. with ends of bars shouldered and/ or rivetted or forged into spikes; framed guard bars, and similar works, complete all as specfied.

Galvanised mild steel wire cloth 0.63 nominal dia of wire and average width of aparture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified.

Sheet glass ordinary quality, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified.

Mild steel butt hinges, medium weight, cold rolled,100mm long, complete all as specified.

30mm wide Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.

300mm long aluminium alloy anodized sliding door with haps, staple (bolt type) and fixing clips of sheets, cast or extrusted sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified.

Aluminium anodised, barrel tower bolts of extruded section of size 150mm and fixed, complete all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded section of size 75mm and fixed, complete all as specified and directed.

Aluminium alloy handles, cast type, anodised of size 150mm and fixed, complete all as specified and directed.

Aluminium alloy handles, cast type, anodised of size 100mm and fixed, complete all as specified and directed.

300mm ordinary rat tail brass rod pattern springs including roller and roller plate fixed, complete all as specified.

Hasp and staple of size 75mm, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws, complete all as specified.

Applying two coats of synthetic enamel paint of Ist quality over a coat of red oxide primer to new or previously untreated steel surfaces over 10cm width or girth including preparation of surfaces, complete all as specified and as directed.

Preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of Ist quality over a coat of pink primer,complete, all as specified.

Extra over rates of block board or veneered particle board for external teak wood lipping, 6mm thick fixed with nails, complete all as specified & directed.

50mm thick PCC 1:3:6 Type C-1 (using 20mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finished the surfaces even & fair, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified.

75mm Cast iron soil, waste and vent pipes (Sand cast pipes) in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified.

Description all as per item No-53 above but fixed to wall, complete all as specified.

100mm Cast iron soil, waste and vent pipes (Sand cast pipes) in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified.

Description all as per item No-55 above but fixed to wall, complete all as specified.

Extra over cast iron pipes and fittings of 100mm bore if lead joint is provided in lieu of cement joint complete all as specified.

Extra over cast iron pipes and fittings of 75mm bore if lead joint is provided in lieu of cement joint complete all as specified.

Bends (any radius), diminishing pieces or tapers (larger bore measured) for 75mm cast iron pipes, complete all as specified.

Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches for 100mm cast iron pipes, complete all as specified.

Bends (any radius) with duck's foot or heel rest for 100mm cast iron pipes, complete all as specified.

Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1(1:2:4) for 75mm cast iron pipes, complete all as specified.

Taking up or down steel water tubings and connections of 15 mm bore pipe laid in trenches or floors or fixed to wall including cleaning for re-fixing or removal to store, complete all as specified and directed.

Taking up or down steel water tubings and connections of 20 mm bore pipe laid in trenches or floors or fixed to wall including cleaning for re-fixing or removal to store, complete all as specified and directed.

Steel water tubing 15 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified.

Steel water tubing 20mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceiling or laid in floors, complete all as specified.

Bib tap 15 mm bore with flange, Brass CP, fancy type. with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed, complete all as specified.

15mm bore Stop valve cast copper alloy chromium plated fancy type with long shank and cup (concealed type) screwed down high pressure with crutch or butter-fly handle, screwed both ends for iron pipes or for union, fixed, complete all as specified.

PVC connection 15mm size with PTMT nuts of length 600mm fixed in repair, complete all as specified and directed.

Vitreous china wash down water closet pan (pedestal pattern) snow white including plastic seat cover closed pattern with flat bottom & mild steel CP screws, complete connection to drain (outgoing pipe) and to flushing pipe and anti syphonage pipe etc with & including fixing bolts fixed in repair, complete all as specified.

PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC. flush pipe for low level cistern including all joints fixed in repair , complete all as specified and directed.

Vitreous china wash hand basin, white, flat back, size 550x400 mm with pedestal excluding taps, waste, chain & plug and porcelain stopper but including brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand etc fixed in repairs, complete all as specified.

Grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40gms) suitable for floor taps, all as specified and directed.

15mm bore pillar tap, cast copper alloy chromium plated with capstan head, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shank and fly nuts screwed for iron pipe and fixed, complete all as specified.

32mm bore PVC waste pipe suitable for wash hand basin & urinals, complete all as specified.

Dismantling PVC water tanks and removing to storing capacity exceeding 500 ltr and not exceeding 1000 ltr complete all as specified.

500 ltr capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) and fixed in position, all as specified in SSR Part-I with & including 15mm ball brass valves, high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule, 20mm bore fixed including dismantling of old water tank of any description, complete all as specified.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for foundation etc for shafts, wells,cesspits, man holes, pier holes etc not exceeding 10 sqm on plan and not exceeding 1.5m depth and getting out in any type of soil, complete all as specified.

Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundations filling and mass concrete, complete all as specified.

Brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar (1:4), all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, in any type of soil, complete all as specified and as directed.

Removing excavated material (soil) not exceeding 50m and deposition where dircted at a level not exceeding 1.50m above the starting point, all as specified and directed.

Hard core of broken stone/boulders of gauge n exc 63mm deposited spreed and leveled in layers n exc 15cm thick watered and rammed to a true surface, complete all as specified.

100mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in sub-floors/path, finishing the surface even & rough, complete all as specified.

50 mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in floor finishing surface even and fair,complete all as specified and as directed.

Cement concrete (1:2:4) using 20mm graded stone aggregate as in lintels upto 1.5 metre clear span, cills, steps, siesmic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm height, copings, benching, bed block, kneelers, apex stones, bed plates, roof kerbs round or chamfered on edges, water troughs and the like including weathering, slightly rounded or chamfered angles and throatings etc.including necessary form work complete all as specified and directed by Engineer-in-Charge.

15mm thick rendering in CM 1:4 on fair faces of brick or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified.

Preparation of newly plastered wall surfaces and applying two coats of cement base paint, complete all as specified.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, confirming to Fe-410-W (Gde E-250) quality-A complete all as specified.

PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint laid in floor / fixed to walls as soil pipe(vent pipe), complete all as specified and directed.

Surface excavation not exceeding 30cm deep and average 15cm deep and getting out in any type of soil, complete all as specified and directed.

100mm thick PCC 1:5:10 type E-2 (using 40mm graded crushed stone aggregate) as in sub base to flooring/path etc, complete all as specified and directed.

Machine pressed chequered cement concrete tiles with chemical resistant coating of size 300x300x 25mm thick laid in floors / path etc. set, jointed and pointed in neat cement slurry with grey cement and no pigment over and including 20mm thick screed bed in CM 1:4, complete all as specified and directed.

E&M PORTION:- Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

Point wiring with two single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable and one single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable as earth continuity to common earth and connecting to earth dolly running in and including PVC casing & caping (ISI marked) of suitable size with PVC boards of appropriate sizes and all requisite accessories such as PVC elbow, Tee, collars, bends etc. with PVC terminals box & cover for mounting swtches, sockets, fan regulator etc for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :-

One light/fan point controlled by one, one way switch 6 Amp complete all as specified.

One bell point controlled by one, one way switch 6 Amp complete all as specified.

One 3 pin socket outlet 6 amp on same board complete all as specified.

One 3 pin socket outlet 6 amp independent complete all as specified.

Description all as per srl item No 96 here in before but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 1.5 sqmm as in continuous earth wire.

Switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified. Make:-Havells/Anchor or equivalent cat part of make as specified in P.S.

Switch piano flush type 16 Amp single pole one way, (ISI marked), complete all as speciied. Make:-Havells/Anchor or equivalent cat part of make as specified in P.S.

Socket outlet multipurpose combination 2 in 1, 3 pin, 5 Amp flush type universal,complete all as specifed. Make:-Havells/Anchor or equivalent cat part of make as specified in P.S.

Socket outlet multipurpose combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal,complete all as specifed. Make:-Havells/Anchor or equivalent cat part of make as specified in P.S.

Switch bell push flush type 5 Amp single pole one way (ISI marked) complete all as specified. Make:-Havells/Anchor or equivalent cat part of make as specified in P.S.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades & depositing to store, complete all as specified. Make:-Havells/Anchor or equivalent cat part of make as specified in P.S.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan after repair if any as obtained / taken out from item No--, complete all as specified and directed. Make:-Havells/Anchor or equivalent cat part of make as specified in P.S.

Electric bell ding dong type 230 volts AC supply all as specified and directed by Engineer-in-Charge. Make:-Havells/Anchor or equivalent cat part of make as specified in P.S.

Ceiling rose, 3 phase PVC/poly carbonate, insulated body, compete all as specified. Make:-Havells/Anchor or equivalent cat part of make as specified in P.S.

Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed. Make:-Havells/Anchor or equivalent cat part of make as specified in P.S.

LED street light fittings 30 Watt made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 complete with hosing with all accessories pre wired with and including 40mm dia GI pipe bracket of 1.2 mtr made to shape as required fixed on wall or pole with FI clamp of required shap & 40x6mm size, nut, bolts, washers and making connection with copper flexible cable of suitable size to light fitting fixed in repairs, complete all as specified and directed. Make:-Havells Cat Part No:ENDURAPEARLSL30WLED757SASYTOPCMP or equivalent cat part of make as specified in P.S.

Decorative wall light fixture made up of polycarbonate, suitable for 10W LED lamp including 10W LED lamp( B-22 base) and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to wall fitting fixed in repairs, complete all as specified and directed. Make: Havells Cat Part No LHDL02160099 or equivalent cat part of make as specified in P.S. Note :- The LED fittings and LED lamp shall be of same make.

Tube light fitting with universal batten suitable for T8 LED lamps LED 20W tube Rod with end cap complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting including 20LED tube rod 4 feet long (Double Side Connection) fixed, complete all as specified and directed. Make:-Havells Cat Part No:-REGALBATTENT8UPTO1X22WSSBSWH for fittings & CRYSTAL 1213T8DSTL20WLED865SGLASS for LED tube rod or equivalent cat part of make as specified in P.S. Note :- The LED batten and LED tube rod shall be of same make.

LED Tube light fitting suitable for LED 10W tube rod made out of with polycarbonate housing & integrated electronic driver complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting including 10W LED tube rod complete all as specified and directed. Make:-Havells Cat Part No:-LHLDEFXD5L8R020 for LED tube rod & Cat Part No:LUMILINEBS9WLED865SPCWH for batten fittings or equivalent cat part of make as specified in P.S. Note :- The LED batten and LED tube rod shall be of same make.

Submain wiring using two single core PVC insulated unsheathed multistranded cables with copper conductor(FRLS) of size 6 sq.mm (nominal area) & drawing with & including PVC casing caping / PVC conduit as directed including provision of 4 sq.mm copper conductor(FRLS) PVC insulated unsheathed multistranded earth wire, complete all as specified.

Vertical distribution board TPN 4 ways with 63 amp 4 pole MCCB 35 KA built in bus bars, neutral links, blanking plates double door as incommer and out going SP/TP MCBs with & including MCB four pole 63 amps 415 volts 10 KA 'C' series fixed in repairs, complete all as specified and directed.Make:-Havells cat part No-DHDLVDRWGOFO04 for DB & cat part No-IHLANF0063 for MCCB or equivalent cat part of make as specified in P.S.

MCB triple pole & neutral 40-63 amps 415 volts 10 KA 'C' series fixed, complete all as specified. Make:-Havells cat part No-DHMGCTNF040-DHMGCTNF063 or equivalent cat part of make as specified in P.S.

Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 8 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning fixed in repairs, complete all as specified. Make:- Havells cat part No-DHDPSHODPW08 or equivalent cat part of make as specified in P.S.

MCB single pole & neutral 40 amps 240 volts 10 KA 'C' series fixed, complete all as specified. Make:-Havells cat part No-DHMGCSNF040 or equivalent cat part of make as specified in P.S.

MCB single pole 6-32 amps 240 volts 10 KA 'C' series fixed, complete all as specified. Make:-Havells cat part No-HMGCSPF006-032 or equivalent cat part of make as specified in P.S.

Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-1 as in earthing pit and cover 50mm thick reinforced with 6mm dia MS round bar @ 10cm C/C both way and MS frame, common salt, charcoal and testing on completion, complete all as specified and directed.

M/S RAJ ENGINEERS