SPL REPAIR TO BLDG NO. P-66 AND P-69 AT HQ CE JAIPUR ZONE ALONGWITH PROVN OF ROOF TREATMENT FOR BLDG NO. P-75 AND CERTAIN MINOR WORKS UNDER ZONE-II AT JAIPUR MIL STN

Amount

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L pre-cast cement concrete 1:3:6, type C1 (using 20mm graded stone aggregate) block masonry with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L for Cutting into old masonry to form toothings for and bonding in new brick or stone work including making good cement mortar of the same mix as for new walling complete all as specified and directed.

Taking down cement plaster or cement lime plaster, any description on brick, stone walls or concrete surface of ceiling etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed

M&L rendering 15mm thick in CM 1:6 on stone masonry surfaces or on surface other than fair faces of brick masonary finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:3 on concrete surface of ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in two layers, 1st layer 10 mm thick in CM 1:4 and IInd layer 5 mm thick in CM 1:4 incl mixing of WPC as per manufacturers instruction, on stone masonry surfaces or on surface other than fair faces of brick masonary, finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge. Note : WPC shall be measured and paid seperately

Supply only integral water proofing compound complete all as specified.

M&L for preparation of newly plaster surface of walls and applying two coats of premium exterior emulsion paint, 1st quality (company depot tinted) of approved manufacturers in required colour and shade using hand roller over and including one coat of alkali resistant priming paints over 1mm thick (avg thickness) wall care putty including rubbing with suitable sand paper to make the surface smooth complete all as specified and directed .

M&L for preparation of newly plaster surface of walls and applying two coats of premium plastic emulsion paint, 1st quality (ready mix) of approved manufacturers in required colour and shade using hand roller over and including 1mm thick (avg thickness) wall care putty including rubbing with suitable sand paper to make the surface smooth complete all as specified and directed .

- ditto- all as per srl item No 10 above but in ceiling complete all as specified and directed.

M&L for complete removal exising treatment on old plastered surfaces of wall by mechanical means and scraping down smoke root mould moss and efforescent salts and treating oil and greasy spots as applicable, preparation the surafce and applying two coat of premium exterior emulsion paint, 1st quality (company depot tinted) of approved manufacturers in required colour and shade using hand roller over and including one coat of alkali resistant priming paints over 1mm thick (avg thickness) wall care putty including rubbing with suitable sand paper to make the surface smooth complete all as specified and directed .

M&L for complete removal exising treatment on old plastered surfaces of wall by mechanical means and scraping down smoke root mould moss and efforescent salts and treating oil and greasy spots as applicable, preparation the surafce and applying two coats of premium plastic emulsion paint, 1st quality(ready mix) of approved manufacturers in required colour and shade using hand roller over and including 1mm thick (avg thickness) wall care putty including rubbing with suitable sand paper to make the surface smooth complete all as specified and directed .

- ditto- all as per srl item No 13 above but in ceiling complete all as specified and directed.

Taking up or down 15 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed.

Taking up or down 20 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed.

S&F 15 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

S&F 20 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubish off the premises complete all as specified and directed.

M&L for light shade vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles n exc 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in CM 1:6 complete all as approved and directed.

M&L for light shade vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles n exc 0.36 sqm, on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed

M&L for coloured glazed ceramic tiles 450mm X 300mm X 7 to 8mm thick on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed

M&L for coloured jointfree non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile 0.18 sqm but not exceeding 0.38 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed

Taking down chowkhats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

Providing and fixing factory made uPVC white colour Sliding window (Area not exceeding 2.00 sqm each) Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware : Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories for fixing of window complete all as specified and directed. Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.)

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F 4 mm thick sheet glass, odinary quality and glazing with neoprene beading in square exc 0.5 Sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples and aluminium glazing clip complete all as specified and as directed.

S & F Factory made gauge panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; but wire gauzed i.e. panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firml in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed. Note :- S & F Glass/gauge shall be measured and paid for separately

Supply and fix Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. Note:Butt hinges shall not be paid separately

S & F 100 mm butt hinges medium weight cold rolled mild steel and fixed complete all as specified and as directed.

S&F Rebated mortice lock, brass, 4 lever, vertical type, size 100 mm complete all as specified and as directed.

S & F rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and incl either hooks and pintal hinges or steel hanging door fittings (exclusive of steel, sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete confirming to Fe-290 Gde-E-165 complete all as specified and directed

Taking down eaves gutters, sanitry PVC pipes and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

S&F 75 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints laid in trenches or floors complete all as specified & directed.

S&F 110 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints laid in trenches or floors complete all as specified & directed.

S&F 75 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed.

S&F 110 mm bore UPVC (SWR) rain water pipes (type A conforming to IS-13592) single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed.

S&F 110 mm dia UPVC (SWR) bends any radius complete all as specified and as directed.

S&F 110 mm dia UPVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and as directed.

S&F 75 mm dia UPVC (SWR) bends any radius complete all as specified and as directed.

S&F UPVC (SWR) gully traps of size 125/110 setting and jointing with solvent cement complete all as specified and directed.

S&F in repair UPVC (SWR) floor trap oulet dia 110mm, plain with grating including jointing with solvent cemet complete all as specified and as directed.

S&F in repair wall hung water closet with concealed flusing cistern with frame, seat cover and twin flushing fittings EWC, pneumatic face plates in polished chrome and connecting including taking down old all as specified and directed by Engineer-in-charge

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and directed.

S&F in repair toilet paper holder with flat recessed stainless steel with suitable fixing arrangements all as specified and directed.

S& F in repair hand made double bowl kitchen sinks with drainage board made of 304 grade staineless steel of min size (1210 x 510mm) having bowl size min (480x460mm) and (300x460mm), depth min 230mm and installation under mount including chromium plated brass coupling for sink fitting including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe and fixture complete all as specified and as directed. Make : Cera, Kohler, Hindware

S&F in repairs viterous china wash hand basin, counter top bowl type/ rectangular/ square type, including bottle trap and all waste fitting accessories i.e. 32mm bore waste couplingof PTMT, PVC waste pipe etc incl fixing of mixer complete all as specified and directed.

Supply only WHB mixer, 15mm bore, brass, fancy type, chromium plated, single lever, swan neck with crutch or butterfly handle, for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. Note : Fixing of mixer included in quoted rates of WHB

S&F in repair vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe and including waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement incl 32mm bore waste coupling of PTMT (half or full threaded) suitable for urinal complete all as specified and directed.

S&F urinal spreader of PTMT (minimum weight 60gms) any colour for fixing with 15 mm dia pipe complete all as specified and directed.

S&F in repair 12mm thick frosted toughened glass for urinal partition, of size 310x700 mm terminating about 40cm above floor line,fixed with suitable SS clamp incl all necessary accesories for fixing complete all as specified and directed.

S & F in repair 15mm bore sink mixer, brass, chromium plated, fancy type for mixing hot & cold water, bright finish screwed the ends for iron pipe and plugging complete all as specified and directed.

S&F in repair PVC Connections 15mm size, 450mm long with PTMT nuts complete all as specified and as directed.

S&F in repair SS Grating doom 125 mm dia with or without waste hole complete all as specified and as directed.

S&F in repair 15mm bore stop/angle valves, cast copper alloy, fancy type, chromium plated, screwed down high pressure with crutch or butterfly handle screwed for iron pipes or for unions and fixed complete all as specified and directed.

S&F Liquid soap container of PTMT (Minimum weight 105gms) fixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

S&F in repair tubular towel rail, brass chromium plated, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

S& F Stainless steel peg stay six complete all as specified and as directed

S&F in repairs 15mm bore stop valves, cast copper alloy fancy type, chromium plated with long shank and cup (concealed type), screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S&F as in repair 15 mm bore two way bib tap, cast copper alloy chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S & F in repair 15mm bore wall mixer, brass, chromium plated, fancy type, 3-in-1 for mixing hot & cold water, with L-bend pipe for connection to overhead shower, bright finish with three joints screwed the ends for iron pipe and plugging complete all as specified and directed.

S&F in repair Brass chromium plated shower rose 125mm size with or without swivel joints, including fixing to steel pipe or union complete all as specified and directed.

S&F in repairs 15 mm bore bib tap, fancy type, chromium plated cast copper alloy with cruth or butter fly handle, long body, screwed down, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S & F in repair 500 Ltrs capacity rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) hoisted and fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc incl dismantling of old tank complete all as specified in SSR Part I and directed by Engr in charge.

Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15cm thickness (below or above ground level) complete all as specified and as directed

M & L for 75mm thick PCC 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed .

Demolition of stone slab and tiles of any description or thickness in floor aprons etc laid bedded and pointed in any mortar complete all as specified and directed .

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for Rounding to edges of stones slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8, type D-2(40mm graded aggregate) as in sub base complete all as specified and as directed.

M & L for 50 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in floors complete all as specified and directed.

M & L for 25mm to 30mm thick precast concrete rubber moulded heavy duty parking tile of minimum size 300mmx300mm minimum M-35 grade, confirming to IS 1237:2012 fixed in position incl necessary vibration etc complete with gray cement and pigment, laid over and incl 15mm thick screed bed in CM (1:4) as specified and directed.

M&L for Providing precast cement concrete louvers and jallies, 35 mm thick (measured solid) including all mouldings but excluding frame, type B-0 1:2:4 (12.5 mmgraded stone aggregate) set in CM 1: 4 incl complete all as specified and directed.

Dismantling boarding plywood etc of any description and in any position fixed with nails etc complete all as specified & directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain shutter, cabinets etc of 18mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and including fixing with stainless steel hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note : Hinge shall be paid seperately

S & F auto close hinges, stainless steel of grade SS-304 , bright finish fixed complete all as specified. Make : Godrej, Hindware, Lifetime or equivalent

S & F stainless steel (Grade SS-304) telescopic basket guide/sliding channels suitable for running basket, bright finish complete all as specified & directed. Make : Godrej, Hindware, Lifetime, Hettich or equivalent

S & F stainless steel handles of size 100 mm fancy type of approved make complete all as specified & directed. Make : Godrej, Hindware, Lifetime or equivalent

S & F smart slide stainless steel (Grade SS-304) prerforated cutlery basket, fancy type of size 18" x 20" x 4" of approved make for modular kitchen complete all as specified & directed Make : Godrej, Hindware, Lifetime or equivalent

S & F smart slide stainless steel (Grade SS-304) Cup & saucer basket, fancy type of size 18" x 20" x 4" of approved make for modular kitchen complete all as specified & directed Make : Godrej, Hindware, Lifetime or equivalent

S & F smart slide stainless steel (Grade SS-304) Plain basket, fancy type of size 18" x 20" x 4" of approved make for modular kitchen complete all as specified & directed Make : Godrej, Hindware, Lifetime or equivalent

S & F smart slide stainless steel (Grade SS-304) Plate/thali basket, fancy type of size 18" x 20" x 4" of approved make for modular kitchen complete all as specified & directed Make : Godrej, Hindware, Lifetime or equivalent

S & F smart slide stainless steel (Grade SS-304) Plain basket, fancy type of size 18" x 20" x 6" of approved make for modular kitchen complete all as specified & directed Make : Godrej, Hindware, Lifetime or equivalent

S & F smart slide stainless steel (Grade SS-304) Plain basket, fancy type of size 18" x 20" x 8" of approved make for modular kitchen complete all as specified & directed Make : Godrej, Hindware, Lifetime or equivalent

Taking down existing roof treatment complete including demolition of PCC, Mud phuskas, lime concrete etc any description upto mother slab, and properly cleaning the surface to remove loose particles with wire brushes and removing the debris out side of MoD land complete all as specified and as directed by Eng- In-Charge.

M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 40mm thick PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) finished even & smooth without using extra cement to cover negative slope into prop complete all as specified and directed

M&L screed plaster 15mm thick in CM 1:4 on concrete surfaces of roof to receive water proofing treatment and finished the surface even and fair incl mixing of WPC as per manufacturers instruction complete all as specified and directed. Note:- Water proofing compound paid seperately as supply only

M & L for Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified and directed

M & L for priming surfaces of roof and applying normal treatment (for moderate conditiion) using glass fibre base bituman felt, grade 2 and applying APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by torched application and applying two coat of aluminium paint on roof surafce all over surface all as specifiedcomplete all as specified and directed by Engr-in-Charge. Note: (i) roof treatment to be done through authorised applicator only (ii) Aluminium paint shall be measured and paid as supply only

Supply only Aluminium paint (in dual containers) complete all as specified and as directed.

S&F in repair 20 mm dia SS (grade 304) drapery/curtain rod medium weight incl taking down old one with finials, brackets etc complete all as specified and directed

S&F SS -304 grade brackets/ end brackets for holding drapery rod complete all as specified and as directed.

S&F SS Finials suitable for 20mm dia SS 304 grade drapery rod as approved complete all as specified and directed

M&L for preparation of new or previously untreated steel and iron surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

M & L for providing precast cement concrete type B1 1:2:4 (using 20mm graded aggregate) in landing, cover slab (for man hole etc) chullah hood, chajjas, water troughs, mangers, shelves and similar articles with plain faces incl form work set in cement mortar 1:4 complete all as specified and directed.

M&L Mild steel TMT bar 10 mm dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as directed and specified.

,--- ditto--- all as per srl item No. 100 above but TMT bar of 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders complete all as directed and specified.

S&F in repair 25mm ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth, for foundation etc or for shafts, wells, manholes, pier holes etc n.exc 10 Sqm on plan and n.exc 1.5 m in depth and getting out in Soft/loose soil complete all as specified and directed.

,---ditto--- all as per srl item No 103 above but depth exc 1.5m but not exc 3m complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft / loose soil complete all as specified and as directed.

Removing excavated material to a distance n exc 50 m and deposited where directed at a level n exc 1.5 m above the starting point complete all as specified and as directed.

Supply, laying, jointing and testing of 200mm bore, DWC pipe (Double wall corrugated) of class SN-4 for sewer line, as per IS-16098 (Part –II), laid in trenches and jointed complete including all necessary fittings i.e. coupler, bend, Tee, reducer etc incl demolition and breaking up complete all as specified & directed . Note : Earth work shall be measured and paid seperately

M&L for surface dressing not exc 15 cm deep in soft/loose soil complete all as specified and as directed.

M&L for PCC 1:4:8, type D2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L RCC (nominal mix) 1:2:4 type B-1 (using 20mm graded aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete and the like complete all as specified and directed. Note : Reinforcement & formwork shall be measured and paid for separately.

M&L RCC (nominal mix) 1:2:4 type B-1 (using 20mm graded aggregate) as in slab supported on walls , beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. Note : Reinforcement & formwork shall be measured and paid for separately.

Use & waste of form work for flat fair finish surface to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc.and similar items complete all as specified and directed.

Use & waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.and similar items with rough finished surface of concrete complete all as specified and directed.

Use and waste of formwork to sides and soffits of suspended slabs such as roof slab, floor slabs landing horizontal or slopping and similar workks thikness n.exc 200mm including neccesarry sufficient supports etc for flat and rough finished surfaces of concrete etc complete all as specified and directed

M&L for rendering 15 mm thick in two layers, Ist layer 10 mm thick in CM 1:4 and IInd layer 5 mm thick in CM 1:4 incl mixing of WPC as per manufacturers instruction, on fair faces of brick masonary or concrete surfaces of wall, finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge. Note : WPC shall be measured and paid seperately

M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick masonry surfaces or concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M&L providing cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in lintel up to 1.5 mtr clear span, cills,steps,seismic and other similar bands, plinth course, string course, lacing course, parapets and railing up to 60cm in height, coping, kneelers, apex stones, bed plates kerb, water troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed

M & L for preparing new plastered surfaces of wall, AC sheet, RCC jallies etc and applying two coats of cement base paint in plain patterns over a coat of alkali resistant priming paint all as specified and as directed

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L hardcore of Broken stone /Boulders of gauge n exc 63 mm, deposited spread and levelled in layers n exc 15 cm thick watered and rolled /rammed to a true surface complete all as specified and as directed.

M & L for 80 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in floors complete all as specified and directed.

M&L for brick work with sub-class 'B' bricks (old size), straight or curved on plan exc 6m mean radius built in In cement mortar 1:6 complete all as specified and directed

M&L Jodhpur stone roof slabs, self faced 7.5 mm to 10 cm thick, 25 cm to 35 cm wire hoisted and set, joined and grounted in CM 1:3 complete all as specified and as directed by Engineer-in-Charge.

S & F Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20mm dia complete all as specified and directed. Note : Min weight for 20mm - 210gm

M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates; hook and pintle hinges, large hasps and staples; chains, hand made sliding bolts; clamps, hold fasts, wall ties; plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed

Providing & Fixing of Mineral Fibre Acoustical Suspended Ceiling System with Dune Tegular 24 Edge Tiles of 16mm thickness and Prelude 24mm face exposed grid. The tiles shall have sand texture visual with acoustical punchers, Humidity Resistance (RH) of 99%, NRC 0.5 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 33db as per ASTM E1414, Light Reflectance ≥85% as per ASTM E-1477, Thermal Conductivity k = 0.052 - 0.057 W/mK, Colour Global White, Fire Performance of class 0/1 as per BS 476 Part 6/7 and Class A as per ASTM E84 with Board edge in module size of 600 x 600mm. It shall be suitable for Green Building application, with Recycled content of up to 41%. The tile shall have certifications from GRIHA and GreenPro thereby confirming that it is an environment friendly product. SUSPENSION: The tile shall be laid on Prelude 38 with 24 mm wide T - section flanges colour global white (matching to tile colour) having roll formed double stroke rotary stitching on all T sections i.e., the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm (all sections). The deflection loading of the system shall be 15 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 18kg/m. The end details of the cross tee shall be made of pre hardened steel and fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. All main beam to main beam and cross tee to cross tee connection shall have a pull-out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel of 90 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability. INSTALLATION: To comprise main runner spaced at 1200mm securely fixed to the structural soffit using suspension system (specifications above) at 1200mm maximum. The First/Last suspension system at the end of each main runner shall not be greater than 450mm from the adjacent wall along with the first and the last main beam shall be at less than 600mm from the wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls using screws at 450mm centre to centre maximum. Installation shall be carried out as per recommended procedure. SUSPENSION SYSTEM accessories supplied by consisting of M6 Anchor Fasteners with hanger hole, pre-straightened hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum loading strength of 110 kgs. (Optionally, adjustable hook clips made of 0.7mm thick Grade 1 C55 galvanized spring steel of dimension 100 x 20mm and 4 mm aquiline wire to be used for level adjustment during installation purpose in main runners).

Taking down carefully surface aluminum /copper point wiring, casing capping /PVC concealed conduit for (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling rose, regulators, sockets, light fittings etc and making good disturbed surfaces complete all as specified and directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable, single core, 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor incl modular sunken GI metal boxes not less than 1.0mm thick moulding in wall and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc as required for one light point controlled by one, one way switch 6 Amp complete all as specified and directed.

,---ditto--- all as per item No. 128 here-in-before but for one fan point controlled by one switch 6 amp complete all as specified and directed.

,---ditto--- all as per item No. 128 here-in-before but for one 3 pin 5 Amp socket outlet controlled by one switch on same board complete all as specified and directed.

,---ditto--- all as per item No. 128 here-in-before but for one 3 pin 5 Amp socket outlet controlled by one switch on indepdendent board complete all as specified and directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable single core, 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor incl modular sunken GI metal boxes not less than 1.0mm thick moulding in wall and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc as required for one 16 Amps socket outlet point controlled by one swith on independent board complete all as specified and directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable single core, 4 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor incl modular sunken GI metal boxes not less than 1.0mm thick moulding in wall and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc as required for one 20 amp, single pole & neutral, socket outlet with 2 pole and earth, metal enclosed plug top complete all as specified and directed.

M&L for sub main wiring with two run of 4 Sqmm single core, PVC insulated, unsheathed, FRLSH multistranded copper conductor cable alongwith one run of 4 Sqmm earth wire as earth continuity conductor (Phase-Red, Neutral-Black, Earth-Green) drawing into and including concealed rigid non-metallic PVC conduit of 25mm dia, ISI marked, ivory colour with fitting / fixing accessories of suitable size as required including making connection as required complete all as specified and directed. NOTE - Two run of 4 sq.mm phase and neutral wire, One run of 4 sq.mm earth wire & One run of PVC conduit with accessories shall be measured as One length.

S&F modular switch, 6 Amps, one way, 240 volts, 1 module complete all as specified and directed.

S&F modular switch 16 Amps, one way, 240 volts, 1 module complete all as specified and directed.

S&F modular socket, 6/16 Amps, 2/3pin combined, 2 module AC 240 volts complete all as specified and directed.

S&F modular socket, 6 Amps, 2/3 pin combined, 2 module AC 240 volts complete all as specified and directed.

S&F modular hum free electronic step fan regulator 120-280 volts of 120 watts capacity (socket type) including connecting up complete all as specified and directed.

S&F angle holder, insulated polycarbonate body with back plate complete all as specified and directed.

S&F LED bulb 9/10W, 230V, edison screw type, energy saver, cool bright light, beam angle >120 degree complete all as specified and directed by the Engineer-in-Charge

S&F ceiling rose PVC polycarbonate isolated body, 3 terminals 230 Volt complete all as specified and directed by Engr-in-Charge.

S&F MCBs Distribution board SPN, 2 ways, powder coated CRCA steel sheet, degree of protection IP-43, IK-09 with reversible double door, 240V, recess mounted having insulated 200 amp tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, blanking plate in unused spaces as required, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs incl taking down old U/S DB complete all as specified and directed. Note : MCBs and MCB DB shall be of the same make.

S&F in repair MCBs Distribution board SPN, 8 ways, powder coated CRCA steel sheet, degree of protection IP-43, IK-09 with reversible double door, 240V, recess mounted having insulated 200 amp tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, blanking plate in unused spaces as required, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs incl taking down old U/S DB complete all as specified and directed. Note : MCBs and MCB DB shall be of the same make.

S&F in repair MCBs Distribution board tripple pole and neutral (VTPN) 4 ways, powder coated, CRCA steel sheet, suitable for MCCB incomer upto 160amp, degree of protection IP-43, IK09 with reversible double door, 415V, recess mounted having insulated 250 amp tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plate in unused spaces as required, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs incl taking down old U/S DB complete all as specified and directed. Note : MCCB, MCBs and MCB DB shall be of the same make.

S&F MCBs of 'B' curve, single pole 6 to 32 Amps having breaking capacity 10 KA, ISI marked, 240Volts including required wiring connections with copper lugs of suitable size provided in MCB DBs incl connection testing and commissioning complete all as specified and directed.

S&F MCBs of 'B' curve, Double pole 6 to 32 Amps having breaking capacity 10 KA, ISI marked, 240Volts including required wiring connections with copper lugs of suitable size provided in MCB DBs incl connection testing and commissioning complete all as specified and directed.

S&F MCBs of 'C' curve Double pole, 40 Amps having breaking capacity 10 KA, ISI marked, 240Volts including required wiring connections with copper lugs of suitable size provided in MCB DBs incl connection testing and commissioning complete all as specified and directed.

S&F MCCB four pole, 63amp, 415 volt, adjustable type, with breaking capacity 16KA, thermally adjustable between 70 to 100% including 4 spreader link set of same make as that of MCCB including reqd cable connections with copper lugs of suitable size and testing & commisioning and make good complete all as specified and directed.

S&F LED batten (1.2M) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficiency of 105 lumen per watt and total power consumption not more than 20 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a colour temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete all as specified and directed. Make - Philips Cat part BN308C LED20S-6500 L120 PSU WH, Crompton Cat part CIS-305-40-57-SL-DP-NWH, Havells Cat no STOUTPLUS600BS20WLED840SPCWH.

S&F LED batten (0.6m) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 900 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 10 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a colour temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete all as specified and directed.

S&F ceiling fan 1200mm sweep 50 Hz AC 230 votls, 5 star rated in white colour with BLDC fan motor, Min air delivery 210 CFM with service value 6.00 BEE, incl blade set, 0.45 mtr down rod, canopy set, rubber reel including 0.5 Sqmm three core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling and writing MES No. on fan body as required complete all as specified and directed.

S&F exhaust fan, high speed, steel body 300mm sweep, 1400 RPM, four blade, heavy duty motor, copper wound double ball bearings, grey colour with louver, nuts, bolts and washers incl three core 0.75sqmm copper cable connection with protective steel bird guard complete all as specified & directed.

M&L for taking out ceiling fan 1200mm sweep 50Hz AC 230 volts and refixing at new location including minor repair and replacement of fan blade, down rod, nut, bolt and washer and spray painting in existing colour including 0.5sqmm thre core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling as required and writing MES No. on fan body complete all as specified and directed.

S&F DBOXx MCB protected socket suitable for domestic and commercial use 16A, 20A, 25A, IS :13032 & IS :8623 complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode of size 60cmx60cmx6.0mm buried directly in ground, vertically to depth not less than 2.25mtr below normal ground level with top edge of the earth plate at depth not less than 1.5 metre below ground level surrounded from all sides with alternate layers of charcoal and common salt and connected to GI lead wire 4.0mm dia by means of GI bolts, nuts washers & check nuts electrode connected to main switch board or main control board or on poles or on transformer and GI pipe medium grade 20mm bore for watering, 40mm bore GI pipe medium grade for protection of GI wire upto test point including providing funnel and wire mesh GI frame and 10cm thick suitably reinforced RCC pit cover, PCC chamber pit with PCC (1:3:6) type C2 using 40mm graded stone aggregates complete including excavation and earth work in any type of strata, disposal of surplus soil to a distance not exceeding 50 mtr, all as specified ans shown in Electrical plate No. 3 of SSR Part-1, PCC pit shall be provided at least 50 cm away from the earth pit and not just on earth pit including testing on completion complete. (Note - GI lead wire size 4.0mm upto 7.5 m included in the item).

S & F 40 mm bore GI tubing "light grade" with all fittings, fixed to wall/ pole with suitable size MS clamp, nut, bolt, washer etc or laid under road crossing etc as reqd for protection of cable incl painting with two coats of aluminium paint over a coat of red oxide primer complete all as specified and directed. Note : Cost of MS clamp, nut bolt, washer and GI fittings etc shall be inclusive in the quoted rates.

Supply, laying, jointing, testing & commissioning LT under ground cable XLPE insulated, screened PVC sheathed, galvanised steel strips or wire armoured, heavy duty electric cable with multi stranded aluminium conductor, 1100 volts grade cross sectional area 35sqmm, 3.5core confirming to IS:7098 (part-I), laid in trenches, ducts, pipes or fixed on poles or walls including all necessary clamps, nut, bolt, washers, saddle etc complete all as specfied and directed. Note : The cost of AI thimbles / lugs and cable gland etc is included in quoted raes.

M & L Sand cushioning to under ground cable with screened and washed sand (non cohessive), 8 cm before laying cable and 15cm after laying and punned to 18cm after laying of cable complete all as specified and directed by Engineer-in-Charge. Note : Punned thickness shall be considered for payment purpose.

M & L bricks for protection cover to UG cable (with old size sub class B bricks, designation 75) with width equal to length of brick, laid dry and flat abutting each other with gaps between adjecent bricks not exceeding 10mm complete all as specified and directed.

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ

Rakesh Choudhary Contractor (BID ID -3390419)

M/S ROHIT CONSTRUCTION (BID ID -3381247)

MSR INFRATECH (BID ID -3390952)