PROVN OF CERTAIN SENCTION LBW AND SPECIAL REPAIR WORK IN THE AREA OF AGE B/R-II UNDER GE SGNR AT MILITARY STATION SRI GANGANAGAR

Amount

Excavation in trenches n.exc. 1.5 m wide & n. exc. 1.5m in depth for foundation etc. n. exc 10 sqm on plan and n. exc. 1.5 m in depth in soft/loose soil and getting out complete all as specified and directed by Engineer - in - Charge

Returning filling in, including spreading levelling, watering and well ramming in layers not exc. 25 cms thick in soft/ loose soil complete all as specified and directed by Engineer - in - Charge.

M & L for sand filling (25 mm thick) under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer - in - Charge.

Removing excavated material n. exc. 50 m & depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed by Engineer - in - Charge.

M&L for hard core of gauge exc 63 mm but n. exc 100 mm, deposited spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surface using broken bricks complete all as specified and directed by Engineer - in - Charge. complete all as specified and directed by Engineer - in - Charge.

M&L for PCC (1:4:8) type D-2, (40 mm graded stone aggregate) as in foundation filling in mass concrete complete all as specified and directed by Engineer - in - Charge

M&L for reinfocement cement concrete 1: 2:4 Type B-1 (Design mix M-25 ) (20mm graded stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed by Engineer - in - Charge

M&L for reinfocement cement concrete 1: 2:4 Type B-1 (Design mix M-25 ) (20mm graded stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and directed by Engineer - in - Charge

Supply only integral water proofing compound ISI marked complete all as specified and directed by Engineer - in - Charge

M & L brick work with fly ash old size bricks 'B' bricks straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 complete all as specified and directed by Engineer - in - Charge.

M & L brick work with fly ash old size bricks 'B', straight or curved on plan exc 6m mean radius, built in CM 1:6 but except bricks complete all as specified and directed by Engineer - in - Charge.

Damp proof course40 mm thick in PCC 1:2:4 Type B –0 (12.5mm graded stone aggregate) to horizontal or vertical surfaces including mixed with water proofing compound as per manufacture instructions necessary formwork complete all as specified and directed by Engineer - in - Charge. Note:- Supply only WPC to be measured and paid spearately

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed by Engineer - in - Charge

M&L for formwork to to sides of pillars, posts, struts, piers, columns and stanchions including for edges rough finished surfaces of concrete complete all as specified and directed by Engineer - in - Charge

M&L for Second class soft-wood in scantlings clean sawn 40 sqm and over in section in any position complete all as specified and directed by Engineer - in - Charge

S & F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engineer - in - Charge.

S & F Second class hard wood factory made wire glazed and skeleton window shutters, 35mm thick, open rebated and prepared to receive glass, gauze, etc divided into squares with plain, chamfered or rounded mitred and rebated sash bars any number & fitted with cut and mitred beads for securing gauze/wire cloth, etc sizes of members of shutters as specified in SSR Part-I, section 8 clause 8.24 (a) complete all as specified and directed by Engineer - in - Charge.

S & F 35mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed by Engineer - in - Charge.

Taking down chowkats or frames (without taking off shutters from the frame) n. exc.1.5 sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down chowkats or frames (without taking off shutters from the frame) exc. 1.5 sqm and n. exc.4 sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down steel window or ventilator of byt n.exc 1.5 sqm each complete all as specified and directed by Engineer - in - Charge.

S & F aluminium anodised barrel tower bolts 150mm long extruded section complete all as specified and directed by Engineer - in - Charge.

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engineer - in - Charge.

S & F butt hinges, heavy weight, cold rolled mild steel, and fixed of size 100mm fixing properly with screws etc complete all as specified and directed by Engineer - in - Charge.

S & F butt hinges, medium weight, cold rolled mild steel, and fixed of size 100mm fixing properly with screws etc complete all as specified and directed by Engineer - in - Charge.

S&F in reapir 300 mm size mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & directed by Engineer-in-Charge.

S & F aluminium handle, cast type, anodised 150 mm long complete all as specified and directed by Engineer - in - Charge

S & F Extruded aluminium alloy handles, fabricated type, anodised 150 mm long complete all as specified and directed by Engineer - in - Charge

S&F mortice lock with four lever (vertical type) with brass body 100 mm long complete all as specified and directed by Engineer-in-charge.

S& stainless steel curtain rod 25 mm dia (minimum weight 0.36 Kg per RM) with brackets, fancy knobs and rings (20 cm c/c) etc complete all as specified and directed by Engr-in-charge.

S & F Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge. Make:- Prayag cat part No- 323-Tor equivalent cat part as approved by GE

S&F door closer hydraulically regulated, designation No. 3, universal type, suitabel for door shutters of size 701 to 850 mm in width and of weight between 36 to 60 kg complete all as specified and directed by Engineer-in-charge.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer - in - Charge.

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to window / ventilator with stainless steel wire staples complete all as specified and directed by Engineer - in - Charge

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified & directed by Engineer-in- charge.

M&L for TMT bars 8 to 10 mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia using TMT bars complete all as specified and directed by Engineer - in - Charge.

M & L for mild steel TMT bars 5mm dia and over upto and including 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia as in stirrups, spacers and binders complete all as specified and directed by Engineer - in - Charge.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed by Engineer - in - Charge

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded including glazed and gauze complete all as specified and directed by Engineer - in - Charge.

M&L for Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. with Powder Coating on aluminium minimum thickness of powder coating 50 micron as per the specification top and bottom horizontal members and vertical members adjacent to walls and cills where required and fixing with the help of rawl plug and screw or with fixing clip or with expansion hold plate fasteners. Aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required complete all as specified and directed by Engineer - in - Charge.

S&F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed by Engineer - in - Charge

S&F powder coated aluminium windows and ventilator shutters, side hung type without sash bars, aluminium saction weighing 0.55 kg/M including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fitting such as aluminium peg stay 150mm long (1No), powder coated aluminium hinges type B-21 100 mm long (2No), suitable powder coated aluminium handle -(1No), and powder coated aluminium self closing tower bolt 75mm long (1No) complete all as specified and directed by Engineer - in - Charge.

S&F power coated aluminium snap grid frame work for false ceiling size 605x605 mm including hangers complete all as specified and directed by Engineer - in - Charge

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long Size of grid 605 x 605mm complete all as specified and directed by Engineer - in - Charge

S&F 0.63 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed by Engineer - in - Charge

M&L forPre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-charge.

M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-charge.

M&L for Providing and fixing Gypsum Board 12mm thick size (600x600) in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed by Engineer - in - Charge

M & L for 20- 25 mm thick ( min size 55x55 cm) machine cut kota stone slab flooring laid over and including 15 mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed by Engineer - in - Charge.

M & L for 18-20 mm thick machine cut kota stone slab as in vertical surfces such as skirting, dados, laid over and including 10 mm thick backing coat in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed by Engineer - in - Charge.

M & L for 75 mm thick cement concrete 1:3:6 type C –1 (20mm graded stone aggregate) as in plinth protection or similar works finished even and smooth with using extra cement etc complete all as specified and directed by Engineer - in - Charge.

M&L for 75mm thick cement concrete (1:4:8) type D-2, (40 mm graded stone aggregate) as in sub base, foundation filling and mass concrete complete all as specified and directed by Engineer - in - Charge

M&L for 25 mm thick cement concrete 1:2:4, Type B-1 (20mm graded aggregate) as in floor finished even and fair complete all as specified and directed by Engineer - in - Charge.

M&L for glazed ceramic coloured tiles interior grade, of size 450x350x7mm thick as on vertical surfaces like dados or skirting laid over and including 10mm thick rendering in CM 1:4 and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.06 sqm but not exc 0.11 sqm in floor etc, laid over and including 15 mm thick screed bed in CM 1:6 and set and jointed in cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

M&L for virified ceramic tiles 10mm thick (square / rectangular) area of each tile exc. 0.18 sqm but n. exc 0.36 Sqm in skirting/dado etc,. laid over and including 10 mm thick rendering in CM 1:4, set and jointed in cement slurry mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer-in-Charge

M&L for virified ceramic tiles 10mm thick (square / rectangular) area of each tile exc. 0.18 sqm but n. exc 0.36 Sqm in floors etc. laid over and including 15 mm thick screed bed in CM 1:4, set and jointed in cement slurry mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer-in-Charge

M&L for precast coloured rubber moulded concrete machine pressed concrete interlocking paver blocks any shape and size conforming to IS 15658-2006 of 60 mm thickness, M 35 grade wirh grey cement and pigment complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises,complete all as specified and directed by Engineer-in-charge.

Taking down cement plaster on brick or concreate wall surfaces including racking out joints, hacking for key, scrubbing down with water etc. complete complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick in CM 1:4 on brick work or concrete work surfaces including finished even & smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

M&L 15 mm thick rendering in CM 1:6 on brick / concrete wall surfaces including finished even & smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil emulsion distemper, over a coat of chalk whiting complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces of walls with putty and applying two coats of cement based paint over a coat of white wash complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of old decorated wall surfaces by brooming down or steel wire brushing,scrapping down smoke soot,moulds,moss and efflorescent salts and trading oil and greasy spots and then applying one coats of cement base paint complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of old decorated plastered or un-plastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot,moulds,moss and efflorescent salts and trading oil and greasy spots and applying two coats of oil emulsion distemper complete all as specified and directed by Engineer-in-Charge.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 sqm the each pane complete all as specified and directed by Engineer - in - Charge.

S & F 4mm thick figured glass, pin head type and glazing with oil putty or fixed with beads in suqares n.exc 0.5 Sqm in each pane complete all as specified and directed by Engineer - in - Charge

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of new wood and wood based surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of Pink primer complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of old wood and wood based surfaces of any description over 10cm width or girth and applying one coats of synthetic enamel paint (ordinary tint) complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide, zinc chrome primer complete all as specified and directed by Engineer - in - Charge

M&L for preparation of old steel surfaces of any description over 10cm width or girth and applying one coats of synthetic enamel paint (ordinary tint) complete all as specified and directed by Engineer - in - Charge

S & F Galvanised steel water tubing 20 mm bore medium grade with all fittings concealed including cutting chases to brick wall/ceiling or laying in floors and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

S & F Galvanised steel water tubing 15 mm bore medium grade with all fittings concealed including cutting chases to brick wall/ceiling or laying in floors and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

S&F rotational moulded white colour polyethylene water storage tank 500 litre capacity (Cylindrical vertical with closed top) hoisted and fixed in position with necessary fittings complete all as specified and directed by Engineer - in - Charge. (Note : PVC tanks shall be ISI marked, having two layres and white colour)

S&F health faucet (hand shower for EWC) having 1.2 m length with hanging device Chromimum plated complete all as specified and directed by Engineer - in - Charge. Make : Cera/Hindware/Paryware/Jaquar

S&F 15mm bib tap cast copper alloy,fancy type, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferule complete all as specified and directed by Engineer-in-Charge. Make: Prayag cat part no-8310 Parryware cat part no- T3504A1, Cera cat part no- HTF3001151

S&F in repairs 15mm dia brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge. Make:- Parryware cat part no-G4636A1, Prayag cat part No- 8550, CREA cat part No. -F1005501

S&F 15mm bore angle stop cock / valve cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed by Engineer-in-Charge.Make: Prayag cat part no-8310 Parryware cat part no- T3507A1, Cera cat part no- F3002201

S&F 20mm bore Ball brass valves high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed by Engineer - in - Charge.Note:- Minimum weight 455gms

S&F grating doom 100 mm dia of CP fixed complete all as specified and directed by Engineer-in-Charge. Note:- Minimum weight 25gms

S&F PVC connections 15mm size with PTMT nut of length 450mm complete all as specified and directed by Engineer-in-Charge.

S&F 100mm dia bore sand cast, cast iron soil, waste and vent pipes in any length with or without ears with cement joints laid in trenches or fixed to wall complete all as specified and directed by Engineer - in - Charge

S&F 75mm dia bore sand cast, cast iron soil, waste and vent pipes in any length with or without ears with cement joints laid in trenches or fixed to wall complete all as specified and directed by Engineer - in - Charge

S&F 100mm bore cast iron Bends (any radius),with duck's foot or heel rest diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engineer-in-Charge.

S&F 75mm bore cast iron Bends (any radius),with duck's foot or heel rest diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engineer-in-Charge.

M & L for PCC 1:3:6 type C –2 bed to drain pipes 150 mm including packing under, haunching against the sides of pipes after they are laid and tested complete all as specified and directed by Engineer - in - Charge.

S&F PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

M&L for reinfocement concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and directed by Engineer - in - Charge

Cutting for 150 mm pipe into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed by Engineer-in-Charge

S&F vitreous china wash down water closet pan (Pedstal pattern) white excluding flushing cistern & flush pipe but including seat cover complete all as specified and directed by Engineer - in - Charge.

S&F 10 litre capacity low level PVC valve less, syphonic action type flushing cistern, white, with inlet, ball valve, float and handle including bracket and provision of flush pipe of polythene of high density or PVC, 15mm dia and 450 mm long complete all as specified and directed by Engineer-in-Charge. Make:- Prayag cat part No- 501/701, Parryware cat part No-E-8055, or equivalent cat part as approved by GE

S&F toilet paper holder, vitreous China, box type complete all as specified and directed by Engineer-in-Charge

S&F vitreous china wash hand basin white, flat back size 550x400mm including brackets, waste coupling 32mm dia of brass Chromium plated, 15mm dia pillar tap of cast copper alloy with capstan head screwed down, high pressure, with or without letter "Hot or Cold" with long screwed shank and fly nuts, 32mm dia, waste pipe low or high density polyethelene of pressure rating 6 Kg/Sqm and PVC connection with PTMT nuts of 15mm dia and 450mm long cutting for and pinning in end of brackets or erecting stand etc. complete all as specified and directed by Engineer - in - Charge. Make:- Prayag cat part No- 4642, Parryware cat part No-C0406/C 0434, or equivalent cat part as approved by GE

S&F vitreous china soap dish 160x160x90 mm fixed with screws complete all as specified and directed by Engineer - in - Charge

Demolition of brick work built in cement mortar or cement lime mortar complete all as specified and directed by Engineer - in - Charge

Demolition of cement concrete in ground floor and paving n. exc. 15cm thickness (below or above ground level) of any description complete all as specified and directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer - in - Charge.

Dismantling timber scantlings 40 sq. cm and over in section, framed work in any position complete all as specified and directed by Engineer - in - Charge.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed by Engineer - in - Charge.

Dismantling Wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed by Engineer - in - Charge.

S & F Fiber Glass Reinforced plastic (FRP) Door Frames of required colour of three legged of cross section 90mmx45mm having single rebate of 32mmx45mm having single rebate of 32mmx15mm to receive shutter of 30 mm thickness. The laminate door frame molded with fire retardant grade unsaturate polysterresinn and chopped mat.Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiberglass from all sides, MS stay shall be provided at the bottom to steady the frame complete all as specified and directed by Engineer - in - Charge

S & F 30mm thick glass fiber reinforced plastic (FRP) paneled door shutter of required colour and approved brand and manufacture made with fire retardent grade unsaturated polyster resin moulded to 3mm thick FRP laminated for forming hollow rails and style with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings cast monolithically with 5mm thick FRP laminate for panels for conforming to IS:14856-2000 complete all as specified and directed by Engineer - in - Charge.

S&F in replacement galvanised, steel rod 16mm diameter and 2.5 metres length for hanging ceiling fan upto 8 feet approx from ground level complete all as specified and directed by Engineer - in - Charge

S & F in replacement extruded aluminium LED batten channel 20 watt having input voltage AC90-300V, 50Hz, 6500K, with white acrylic cover tube light fitting wall mounted complete with rod, driver and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer - in - Charge. Make :-Havells cat part No. LUMILINEPLUSBS20WLED865SPCSS, Bajaj cat part No. BCLSBAL 20W CW, Crompton cat part No. CCS-100-20-65-HL2-DP-NWH or equivalent cat part as approved by GE

S & F LED lamp 9 W for angle holder complete all as specified and directed by Engineer - in - Charge.

S & F water tight bulk head fitting, comprision of connector galvanised cast iron back plate, weather proof enamelled gallery, glass well and including 10 watt LED lamp complete all as specified and directed by Engineer-in-Charge. Make :-Havells cat part No. HEXAFT10WLED857SSYMBOPC, Bajaj cat part No. BIBWP 10W LED, Crompton cat part No. LBHP-10-CDL

S&F security light fitting LED TYPE 25 watt with all necessary accessories, Clear transparent acrylic cover, prewired suitable to operated on 230 volt 50 HZ AC & Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer - in - Charge. Make :-Havells cat part No. ENDURAPEARLSL25WLED757SASYTOPCMP, Bajaj cat part No. BRLEP 25 W, Crompton cat part No. LSTS-25-CDL-M

S&F ceiling fan of size 1200 mm sweep with BLDC fan BEE 5 star rating having max power consumption less than equal to 35 W single phase 230 volts, 50 Hz complete 3 blades including canopy, fan hook, hanging rod, fan regulator stepped type complete all asspecified and directed by Engineer - in - Charge. Make : Usha Energia 32 1200 mm 5 star, Bajaj Engery smart 32 1200 mm , Crompton Energion HS 1200 mm 5 star, Havells Efficiencia 5 star 1200 mm

S&F Exhaust fan with high speed noiseless motor of size 300 mm sweep, 900 RPM,heavy duty by grouting both ends in wall upto required length and making hole of suitable size in wall, making good the existing surface and connecting with ceiling roses with and including flexible cable 3 core copper conductor of size 24/.2 mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan of suitable length with frame. louvers, nuts, bolts etc. including making good disturbed wall in CM(1:4) complete all asspecified and directed by Engineer - in - Charge. Make- Crompton/Bajaj/Havell's/Orient

Taking down copper/aluminium point wiring (light,fan,socket or power)complete including fixture and fittings such as switches& sockets and removing materials for taking credit complete all as specified and directed by Engineer-in-charge.

M&L for concealed conduit point wiring complete for light /fan with cable 1.5 sqmm(Nominal area) FRLS PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC conduit pipe medium grade 20mm bore,pipe hooks,elbows,junction covers and junction boxes, after cutting in wall chasing for conduits and sinking's for sunken cast iron /pressed steel terminal boxes of suitable length and thickness for mounting switches, sockets, fan regulator with 3mm thick plastic laminated seat cover fixed with brass screws and cup washers, duly grouting and painted with red oxide metal primer and making good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth contuity conductor along with point wiring of 1.5 sqmm copper FRLS PVC insulated cable for one light/fan point controlled by one way switch and connected to common earth dolly, complete all as specified and directed by Engr-in-charge.

All as described in Srl item No -116 here in before but for one switch socket combination 5/6 Amps on independent board complete all as specified and directed by Engineer - in - Charge.

All as described in Srl item No -116 here in before but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in - Charge.

All as described in Srl item No. 116 here in before but for one switch socket combination 6 pin 5/15 Amps on independent board with 2.5 Sqmm (Nominal Area) FRLS PVC insulated multistranded unsheathed copper conductor and continuous earth contuity conductor along with point wiring of 2.5 sqmm copper FRLS PVC insulated copper cable complete all as specified and directed by Engineer - in - Charge.

S & F switch piano flush type 5/6 Amp single pole two way complete all as specified and directed by Engineer - in - Charge

S & F switch socket combination 5 pin, 5/6 Amps flush type complete all as specified and directed by Engineer - in - Charge

S&F Switch socket combination 2 in 1, 6 pin , 15/16 Amp flush universal type all as spd and directed by Engr in charge.

S & F Socket outlet 5 pin 5 Amps flush type complete all as specified and directed by Engineer - in - Charge.

S & F ceiling rose, surface bakelite 65x50 mm three terminals complete all as specified and directed by Engineer - in - Charge.

S & F angle holder insulated body with back plate for conduit fittings complete all as specified and directed by Engineer - in - Charge.

S & F stepped type,single socket fan regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete all as specified and directed by Engineer - in - Charge

S & F sheet metal enclosure for double door DB's made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 8 ways, 240 Volts, 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S & F MCB ‘B’ series type suitable for 240 volts, AC supply 5 to 40 Amps , single pole with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F MCB ‘B’ series type suitable for 240 volts, AC supply 5 to 40 Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F in replacment MCB ‘B’ series type suitable for 240 volts, AC supply 5 to 40 Amps , single pole with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F in replacment MCB ‘B’ series type suitable for 240 volts, AC supply 5 to 40 Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

M & L for Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried in ground (earth pit not less than 2.25 Mtr deep below normal ground level with top edge of the plate not less than 1.5 Mtrs below normal ground level, connecting to the Galvanised iron earth lead 4 mm dia GI earth wire, by means of bolts, nuts check nuts and washers of galvanised iron and protection by provision of GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20mm graded stone aggregate with 40mm thick cover of RCC (1:2:4) reinforced with XPM (wieght not less than 4gs/Sqm) and frame of angle iron 25mm x 25mm x 6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed on top edge of earth plate common salt and charcoal filling test point made out of 40mm x 8 mm FI with fixing arrangements, funnel, wire mesh and earth work in hard dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 Mtrs all as per electrical Plate No.3 of SSR Part I and connecting to earth test point including taking our unserviceable earthing with all acessories all as specified or indicated including testing on completionall as specified and directed by Engineer - in - Charge.

Supplying, laying and testing in replacement 16 Sqmmx2 core XLPE insulated, heavy duty electric cable with aluminium conductor 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/ laid under roads/paths/ drain/ culverts or passing through pipes complete all as specified and directed by engineer in charge.

Excavation in trenches in n.exc. 1.5 m wide & n. exc. 1.5m in depth in soft/ loose soil for laying of cable complete all as specified and directed by Engineer - in - Charge

Returning, filling in, including spreading, levelling watering and well ramming in layers n. exc. 25cm thick in layers soft/loose soil complete all as specified and directed by Engineer - in - Charge

Removing surplus soil n. exc. 50 m & depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed by Engineer - in - Charge.

Supply & filling/ laying a layer of dry coarse sand 8 cm thick before laying ofcable and 15 cm thick after laying of cable complete all as specified and directed by Engineer - in - Charge. Note:- After punning drain 18 cm will be measured for payment.

S & F in replacement sub-main wiring with two single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLS stranded copper conductor drawn and including steel dia "medium quantity" PVC conduit including 6.00 Sq mm (Nominal Area) copper cable as earth continuity conductor after chasing in wall and making good the disturbed surface and white wash or existing colour, necessary junction box and cover including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer - in - Charge.

M&L for brick protection layer with one brick wide using sub class ‘B’ bricks laid flat across the cable complete all as specified and directed by the Engineer in charge.

S & F Galvanised steel water tubing 20 mm bore tight grade with all fittings concealed including cutting chases to brick wall/ceiling or laying in floors and making good disturbed surfaces cable crossing complete all as specified and directed by Engineer-in-Charge.

S & F Galvanised steel water tubing 25 mm bore tight grade with all fittings concealed including cutting chases to brick wall/ceiling or laying in floors and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for cutting existing steel tubing for alterations or additions (Each cut measured), Add if necessarily done in position without taking down complete all as specified and directed by Engineer-in-Charge.

S & F 25 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Note : Notes : (i) Amount of credit for retrieved materials is mentioned in Sch 'A' Section-II of tender documents in pdf form which will be deducted while acceptance of tender offline.

M/s Singla Trading Comapny