1. Balance work of approach road and retaining wall for closure of LC gate no 33A on Sewagram-Ballarshah section. 2. Balance work of approach road, retaining wall and drainage arrangement for closure of LC gate no.11 on Sewagram-Ballarshah section. 3. Balance work of approach road and retaining wall for closure of LC gate no 71 on Wardha-Badnera section. 4. Construction of Relay Hut for Interlocking of LC Gate No 6 (Wani-Kayar) and 1C (Sewagram-Ballarshah) in Nagpur division.

1C (Sewagram-Ballarshah) in Nagpur division.

Item- 01 MS ITEM (DSR 2023)

S No. Item Description of Item Unit Qty Rate Amount

2.0 EARTH WORK

2.1S General

Earth work in excavation by mechanical

means (Hydraulic excavator)/manual means

over areas (exceeding 30 cm in depth, 1.5 m

2.6 in width as well as 10 sqm on plan) including

getting out and disposal of excavated earth

lead upto 50 m and for all lift, as directed by

Engineer-in-charge.

Earth work in excavation by mechanical

means (Hydraulic excavator)/manual means

over areas (exceeding 30 cm in depth, 1.5 m

2.7 in width as well as 10 sqm on plan) including

getting out and disposal of excavated earth

lead upto 50 m and lift upto 1.5 m, as

directed by Engineer-in-charge.

2.27 Supplying and filling in plinth with sand under cum 192 2123.75 407760

3 floors, including watering, ramming,

consolidating and dressing complete.

4.0 CONCRETE WORK

4.1S CEMENT CONCRETE (CAST IN SITU)

Providing and laying in position cement

concrete of specified grade excluding the

cost of centering and shuttering - All work up

to plinth level :

derived from natural sources : 6 graded stone

aggregate 20 mm nominal size derived from

natural sources)

5.0 REINFORCEMENT CEMENT CONCRETE

5.9S FORM WORK

Centering and shuttering including strutting,

propping etc. and removal of form for

5.9.1 Foundations, footings, bases of columns, etc. Sqm 52 392.15 20391.8

for mass concrete

5.9.3 Suspended floors, roofs, landings, balconies Sqm 188 927.25 174323

and access platform

5.9.5 Lintels, beams, plinth beams, girders, Sqm 144 736.4 106041.6

bressummers and cantilevers

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Sqm 136 961.3 130736.8

5.9.16 Edges of slabs and breaks in floors and walls

5.22S STEEL REINFORCEMENT

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in

position and binding all complete upto plinth

5.22.6 Thermo-Mechanically Treated bars of grade Kg 4800 107.85 517680

Fe-500D or more.

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in

position and binding all complete above

5.22A.6 Thermo-Mechanically Treated bars of grade Kg 5600 107.85 603960

Fe-500D or more.

5.33S DESIGN MIX CONCRETE

Providing and laying in position ready mixed

or site batched design mix cement concrete

for reinforced cement concrete work; using

coarse aggregate and fine aggregate derived

from natural sources, Portland Pozzolana /

Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as

per IS: 9103 to accelerate / retard setting of

concrete, to improve durability and

w o r k a b i l i t y without impairing strength;

including pumping of concrete to site of

laying, curing, carriage for all leads; but

excluding the cost of centering, shuttering,

finishing and reinforcement as per direction

of the engineer-in-charge, for the following

grades of concrete.:

5.33.1 All works upto plinth level

5.33.1.1 Concrete of M25 grade with minimum cement cum 36 9504.75 342171

content of 330 kg /cum

5.33.2 All works above plinth level upto floor V level

5.33.2.1 Concrete of M25 grade with minimum cement cum 40 9860.4 394416

content of 330 kg /cum

6.0 MASONRY WORK

6.26S EXPOSED BRICK WALL

Brick work with clay flyash F.P.S. (non

modular) brick of class designation 7.5 in

superstructure above plinth level up to floor

five level in :

9.0 WOOD AND P.V.C. WORK

9.1S FRAMES AND TRUSSES

Providing wood work in frames of doors,

windows, clerestory windows and other

frames, wrought framed and fixed in position

with hold fast lugs or with dash fasteners of

required dia & length (hold fast lugs or dash

fastener shall be paid for separately).

Providing and fixing panelling or panelling

and glazing in panelled or panelled and

glazed shutters for doors, windows and

clerestory windows (Area of opening for

panel inserts excluding portion inside

grooves or rebates to be measured).

Panelling for panelled or panelled and glazed

shutters 25 mm to 40 mm thick :

9.7.8 Fly proof stainless steel grade 304 wire Sqm 8 1800.45 14403.6

16 gauge with 0.5 mm dia. wire and 1.4 mm

wide aperture with matching wood beading

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Providing and fixing ISI marked flush door

shutters conforming to IS : 2202 (Part I)

decorative type, core of block board

9.20 construction with frame of 1st class hard

wood and well matched teak 3 ply veneering

with vertical grains or cross bands and face

veneers on both faces of shutters.

9.20.2 30 mm thick including ISI marked Stainless Sqm 20 3167.95 63359

Steel butt hinges with necessary screws

9.40S MISCELLANEOUS-WOOD WORK

Providing and fixing M.S. grills of required

pattern in frames of windows etc. with M.S.

9.48 flats, square or round bars etc. including

priming coat with approved steel primer all

COPER OXIDISED MILD STEEL FITTINGS

(COPPER OXIDISED AS PER IS: 1378)

Providing and fixing ISI marked oxidised M.S.

9.62 sliding door bolts with nuts and screws etc.

complete (Copper oxidised as per IS 1378)

9.70S STAINLESS STEEL FITTINGS

Providing and fixing IS : 12817 marked

9.71 stainless steel butt hinges (heavy weight)

with stainless steel screws etc. complete :

9.72S BRASS FITTINGS

Providing and fixing bright finished brass

handles with screws etc. complete:

9.82 Providing and fixing bright finished brass Each 8 121.65 973.2

22 hanging type floor door stopper with

necessary screws, etc. complete.

10.0 STEEL WORK

10.1S General

10.1 Structural steel work in single section, fixed Kg 5524.58 117.35 648309.46

with or without connecting plate, including

23 cutting, hoisting, fixing in position and

applying a priming coat of approved steel

primer all complete.

11.0 FLOORING

11.41S VITRIFIED FLOOR TILES

Providing and laying vitrified floor tiles in

different sizes (thickness to be specified by

the manufacturer) with water absorption less

than 0.08% and conforming to IS: 15622, of

approved make, in all colours and shades,

laid on 20mm thick cement mortar 1:4 (1

cement : 4 coarse sand), jointing with grey

cement slurry @ 3.3 kg/ sqm including

grouting the joints with white cement and

matching pigments etc., complete.

12.0 ROOFING

12.37S RAIN WATER SPOUT AND PIPE

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

12.50 Providing and fixing precoated galvanised Sqm 88 738.65 65001.2

iron profile sheets (size, shape and pitch of

corrugation as approved by Engineer-in-

charge) of total coated thickness 0.50 mm

(base metal of minimum 0.45 mm thickness

with total coating thickness of 0.05 mm) with

zinc coating 120 grams per sqm as per IS:

277, in 240 mpa steel grade, 5-7 microns

epoxy primer on both side of the sheet and

polyester top coat 15-18 microns. Sheet

25 should have protective guard film of 25

microns minimum to avoid scratches during

transportation and should be supplied in

single length upto 12 metre or as desired by

Engineer-in-charge. The sheet shall be fixed

using self drilling /self tapping screws of size

(5.5x 55 mm) with EPDM seal, complete upto

any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins, rafters

and trusses and including cutting to size and

shape wherever required.

13.0 FINISHING

13.1S CEMENT PLASTER (IN FINE SAND)

15 mm cement plaster on the rough side of

single or half brick wall of mix :

13.44S EXTERIOR FINISHING

Finishing with Deluxe Multi surface paint

13.48 system for interiors and exteriors using

Primer as per manufacturers specifications :

13.48.1 Two or more coats applied on walls @ 1.25 Sqm 1002 193.7 194087.4

28 ltr/10 sqm over and including one coat of

Special primer applied @ 0.75 ltr /10 sqm

13.48.3 Painting Steel work with Deluxe Multi Surface Sqm 225.6 170.7 38509.92

Paint to give an even shade. Two or more

29 coat applied @ 0.90 ltr/10 sqm over an under

coat of primer applied @ 0.80 ltr/10 sqm of

approved brand and manufacture

15.0 DISMANTLING AND DEMOLISHING

15.1S General

Demolishing cement concrete manually/ by

mechanical means including disposal of

material within 50 metres lead as per

direction of Engineer - in - charge.

(including equivalent design mix)

15.60 Disposal of building rubbish / malba / similar cum 4 263.95 1055.8

unserviceable, dismantled or waste materials

by mechanical means, including loading,

31 transporting, unloading to approved

municipal dumping ground or as approved by

Engineer-in-charge, beyond 50 m initial lead,

for all leads including all lifts involved.

21.0 ALUMINIUM WORK

21.1S General

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Providing and fixing aluminium work for

doors, windows, ventilators and partitions

with extruded built up standard tubular

sections/ appropriate Z sections and other

sections of approved make conforming to IS:

733 and IS: 1285, fixing with dash fasteners

of required dia and size, including necessary

filling up the gaps at junctions, i.e. at top,

bottom and sides with required EPDM rubber/

neoprene gasket etc. Aluminium sections

shall be smooth, rust free, straight, mitred

and jointed mechanically wherever required

including cleat angle, Aluminium snap

beading for glazing / panelling, C.P. brass /

stainless steel screws, all complete as per

architectural drawings and the directions of

Engineer-in-charge. (Glazing, panelling and

dash fasteners to be paid for separately) :

21.1.1 For fixed portion

thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators

including providing and fixing hinges/ pivots

and making provision for fixing of fittings

wherever required including the cost of EPDM

rubber / neoprene gasket required (Fittings

shall be paid for separately)

thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium

door, window, ventilator shutters and

partitions etc. with EPDM rubber / neoprene

21.3 gasket etc. complete as per the architectural

drawings and the directions of engineer-in-

charge . (Cost of aluminium snap beading

shall be paid in basic item):

21.3.1 With float glass panes of 4.0 mm thickness Sqm 30 1176.8 35304

(weight not less than 10kg/sqm)