Loading
Loading…
Loading…
Tender Value
₹2.8 Cr
EMD Value
₹5.6 L
Closing Date
19 May 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
SR.DEN III
14 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
Technical Eligibility Criteria: (a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender. (b) (1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender.Note for b(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2)In such cases, what constitutes a component in a composite work shall be clearly pre- defined with estimated tender cost of it, as part of the tender documents without any ambiguity.(b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract.
Defination of Similar Work :- Any Civil work other than track work.
7 conditions · 1 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tenderer may please note that offers received without requisite/mandatory documents as mentioned above, will be considered as invalid tender and for which contractor shall have no claim on Railway.
The tenderer shall visit the site of work and acquaint himself/themselves with the conditions of work viz. approach roads and accessibility, availability of materials, electric power, water for work and drinking purposes, site for labour camps, stores, godowns, extent of lead/lift in work, availability of skilled and unskilled labour etc. that may be encountered in the course of execution of work. In short, he/they should familiarize himself/themselves fully with the all the conditions of the work site & all the financial implications due to the above conditions is deemed to be understood and taken care of while bidding the offer.
Improvement and provision of minimum essential amenities and Divyangjan facilities i.e. Tactile Paths, ramps, toilets, water booths at various railway station (adarsh Nagar, Sabzi Mandi, Dayabasti, Patel Nagar, Delhi Kishanganj, kirti Nagar, Narayana Vihar) in the section of SSE/W/DLI under ADEN/DLI.
NIT-13-2026-27-W-III
NIT-13-2026-27-W-III
Open
Works - General
6 Months
Delhi, Delhi
₹0
₹5.6 L
19 May 2026
27 Apr 2026
5 May 2026
97 items across 2 schedules · ₹42,76,575.14 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Cost of carriage including loading, unloading & stacking for first 50 metres | cum | 30 | 187.24 | 5,617.2 |
| 2 | Every additional lead of 50m or part thereof beyond1st 50 m upto 9 such additional lead | cum- lead | 20 | 40.77 | 815.4 |
| 3 | All kinds of soil. | cum | 320 | 286.85 | 91,792 |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. | cum | 320 | 253.95 | 81,264 |
| 5 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. | cum | 600 | 368.65 | 2,21,190 |
| 6 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 12 | 6,833.4 | 82,000.8 |
| 7 | 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 12 | 9,375.2 | 1,12,502.4 |
| 8 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 90 | 10,185.05 | 9,16,654.5 |
| 9 | Foundations, footings, bases of columns, etc. for mass concrete | Sqm | 100 | 307.95 | 30,795 |
| 10 | Suspended floors, roofs, landings, balconies and access platform | Sqm | 100 | 766.55 | 76,655 |
| 11 | Lintels, beams, plinth beams, girders, bressumers and cantilevers | Sqm | 60 | 608.35 | 36,501 |
| 12 | Columns, Pillars, Piers, Abutments, Posts and Struts | Sqm | 60 | 804.25 | 48,255 |
| 13 | Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). | cum | 7 | 9,673.5 | 67,714.5 |
| 14 | Mild steel and Medium Tensile steel bars | Kg | 2500 | 88.95 | 2,22,375 |
| 15 | Hard drawn steel wire | Kg | 2500 | 87.5 | 2,18,750 |
| 16 | Thermo-Mechanically Treated bars of grade Fe-500D or more. | Kg | 16000 | 89.65 | 14,34,400 |
| 17 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 60 | 8,683.8 | 5,21,028 |
| 18 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 240 | 10,306.2 | 24,73,488 |
| 19 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 200 | 6,658.25 | 13,31,650 |
| 20 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 120 | 8,288.35 | 9,94,602 |
| 21 | Honey-comb brick work 10 / 11.4 cm thick with common burnt clay bricks of class designation 7.5 in super structure above plinth level upto floor V level with cement mortar 1:4 (1 cement : 4 coarse sand). | Sqm | 140 | 645.95 | 90,433 |
| 22 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. | Sqm | 180 | 1,063.45 | 1,91,421 |
| 23 | 12 mm thick plain grade -1, medium density flat pressed three layer particle board FPT - I or graded wood particle board FPT- I, IS : 3087 marked, bonded with BWP type synthetic resin adhesive as per IS : 848 : | Sqm | 30 | 2,682.05 | 80,461.5 |
| 24 | 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Sqm | 16 | 2,015.75 | 32,252 |
| 25 | Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). | Each | 30 | 194.35 | 5,830.5 |
| 26 | 100x63x4 mm | Each | 70 | 97.6 | 6,832 |
| 27 | 75x63x4 mm | Each | 70 | 79.05 | 5,533.5 |
| 28 | 250x16 mm | Each | 12 | 234.9 | 2,818.8 |
| 29 | 250x10 mm | Each | 12 | 104.4 | 1,252.8 |
| 30 | 150x10 mm | Each | 12 | 75.55 | 906.6 |
| 31 | 125 mm | Each | 16 | 60.05 | 960.8 |
| 32 | Single rubber stopper | Each | 5 | 35.5 | 177.5 |
| 33 | 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames. | Sqm | 20 | 3,496.75 | 69,935 |
| 34 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Kg | 120 | 93.05 | 11,166 |
| 35 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Kg | 13000 | 111.95 | 14,55,350 |
| 36 | Hot finished welded type tubes | Kg | 13000 | 154.9 | 20,13,700 |
| 37 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. | Each | 12 | 185.2 | 2,222.4 |
| 38 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works | Kg | 200 | 142.3 | 28,460 |
| 39 | M.S. tube | Kg | 110 | 157.15 | 17,286.5 |
| 40 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). | Kg | 4400 | 612.25 | 26,93,900 |
| 41 | Stainless steel (grade 304) wire gauge of 0.5 mm dia wire and 1.4 mm aperture on both sides | Sqm | 30 | 971.55 | 29,146.5 |
| 42 | 25 mm thick | Sqm | 600 | 1,706.6 | 10,23,960 |
| 43 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. | Sqm | 120 | 935.6 | 1,12,272 |
| 44 | Size of Tile 600 x 600 mm | Sqm | 200 | 1,286.6 | 2,57,320 |
| 45 | Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in- Charge: | Sqm | 600 | 3,282.5 | 19,69,500 |
| 46 | Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent | Sqm | 300 | 3,908.8 | 11,72,640 |
| 47 | 0.80 mm thick with zinc coating not less than 275 gm/sqm | Sqm | 70 | 1,135.45 | 79,481.5 |
| 48 | With machine moulded common burnt clay F.P.S. (non modular) brick tiles of class designation 12.5, conforming to IS 2690 | Sqm | 200 | 905.8 | 1,81,160 |
| 49 | In 75x75 mm deep chase | Metre | 70 | 260.2 | 18,214 |
| 50 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. | Each | 6 | 266.6 | 1,599.6 |
| 51 | 110 mm diameter | Metre | 200 | 319.75 | 63,950 |
| 52 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in- charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | Sqm | 90 | 671.55 | 60,439.5 |
| 53 | 1:6 (1 cement: 6 fine sand) | Sqm | 500 | 282 | 1,41,000 |
| 54 | Two or more coats on new work | Sqm | 900 | 92.75 | 83,475 |
| 55 | New work (Two or more coats applied @ 3.84 kg/10 sqm) | Sqm | 300 | 97.6 | 29,280 |
| 56 | Two or more coats on new work | Sqm | 300 | 131.45 | 39,435 |
| 57 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. | Sqm | 1200 | 123.85 | 1,48,620 |
| 58 | Old work (one or more coats) | Sqm | 300 | 56.8 | 17,040 |
| 59 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) | cum | 40 | 2,007.1 | 80,284 |
| 60 | For thickness of tiles 10 mm to 25 mm | Sqm | 120 | 60.5 | 7,260 |
| 61 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. | Sqm | 70 | 45.05 | 3,153.5 |
| 62 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. | cum | 420 | 219.35 | 92,127 |
| 63 | Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm | Each | 30 | 5,745.95 | 1,72,378.5 |
| 64 | Cautionary /warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm | Each | 30 | 4,209.2 | 1,26,276 |
| 65 | Overhead informatory road signage | Sqm | 16 | 5,609.55 | 89,752.8 |
| 66 | Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in- charge and accordance with applicable specifications. | Sqm | 240 | 623.8 | 1,49,712 |
| 67 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in- charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in- charge). | cum | 20 | 8,613.55 | 1,72,271 |
| 68 | Providing and laying matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in- Charge. | Sqm | 120 | 1,250.75 | 1,50,090 |
| 69 | Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in- Charge. | Sqm | 1400 | 1,719 | 24,06,600 |
| 70 | 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. | Sqm | 1400 | 1,011.2 | 14,15,680 |
| 71 | W.C. pan with ISI marked white solid plastic seat and lid | Each | 16 | 5,540.55 | 88,648.8 |
| 72 | White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps | Each | 10 | 2,275 | 22,750 |
| 73 | Providing and fixing wash basin with C.I. brackets, 15 mm PTMT pillar cock, 32 mm PTMT waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm PTMT pillar cock. | Each | 8 | 1,404 | 11,232 |
| 74 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. | Each | 8 | 1,500.05 | 12,000.4 |
| 75 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia | Each | 3 | 6,119.15 | 18,357.45 |
| 76 | 65 mm nominal dia Pipes | Metre | 140 | 1,576.9 | 2,20,766 |
| 77 | 15 mm dia nominal bore | Metre | 120 | 485.2 | 58,224 |
| 78 | 20 mm dia nominal bore | Metre | 60 | 315.35 | 18,921 |
| 79 | 50 mm dia nominal bore | Metre | 120 | 654.2 | 78,504 |
| 80 | 15 mm nominal bore | Each | 15 | 303.85 | 4,557.75 |
| 81 | 15 mm nominal bore | Each | 24 | 348.85 | 8,372.4 |
| 82 | 20 mm nominal bore | Each | 24 | 397.45 | 9,538.8 |
| 83 | 15 mm nominal bore | Each | 26 | 85.2 | 2,215.2 |
| 84 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. | Litre | 10000 | 9.7 | 97,000 |
| 85 | 300 mm dia. R.C.C. pipe | Metre | 110 | 902.05 | 99,225.5 |
| 86 | Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) | Kg | 280 | 433.95 | 1,21,506 |
| 87 | Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) | Kg | 160 | 531.8 | 85,088 |
| 88 | With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) | Sqm | 70 | 1,019.8 | 71,386 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
StandardTenderDocument2022R5.pdf Standard Tender Document 2022
ATTACHMENT
GCC-2022withCSupto10.pdf
ATTACHMENT
GCC-2022withCSupto11.pdf
ATTACHMENT
StandardTenderDocument2022R5.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .