IMPROVEMENT OF TOILET BLOCK FOR KV-2 AT AF STN GWALIOR

Amount

Demolition of PCC in ground floor & pavings n.exc 15 cm thick below or above ground level complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

Taking down cement plaster including on brick or stone wall etc incl racking out joints hacking for key & scrubbing down with water etc.complete all as specified and directed.

Demolition of reinforced cement concrete as in Roofs, floors (other than ground floors), beams staircases, landing, chajjas, slab and similar suspended work complete.

Demolition of brick work built in cement motor of any description complete all as specified and directed by the Engineer-in-Charge.

Demolition of PCC of any description and in any position other than ground floor complete all as specified and directed.( For sunken portion )

Demolition of reinforced brickwork in suspended slabs, beams, lintels etc. in cement mortar or cement concrete(reinforcement cut as required to facilitate demolition) complete all as specified and directed.

M & L for rendering 15 mm thick on other than fair faces of brick wall finished even and smooth (without using extra cement) in CM 1:6 complete all as specified and directed.

M & L for rendering 10 mm thick on fair faces of brick wall with mixing water proofing compound (WPC) finished even and smooth without using extra cement in CM 1:4 complete all as specified and directed Note: WPC for mixing shall be measured and paid separately as supply only.

M & L for rendering 5 mm thick on fair faces of brick or concrete surface of ceiling finished even and smooth (without using extra cement ) CM 1:3 complete all as specified and directed. Note:-(1) Cost of scaffolding for rendering is deemed to be included in quoted rate of this item

Supply only water profing compound

M&L glazed ceramic digitally designed coloured tiles 450 x 300 x 7mm thick coloured with highlighter on vertical surfaces such as skirting dados etc, set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles including 10mm thick rendering in cm 1:3 as backing coat complete all as specified and directed.

M&L non skid joint free digitally designed coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tiles exc. 0.11 sqm but not exc. 0.18 sqm, in floor etc set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles including 15mm thick screed bed in cm 1:6 complete all as specified and directed.

M& L Baroda green marble slab 15 to 18 mm thick for window cill and Jambs including 20 mm thick screed bed in cm 1:6 and including Half moulding complete all as specified and direced.

M&L for machine cut Kota stone slab as in floor 20 to 25 mm thick in floor over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab lincluding & grinding mirror polishing and including screed bed 20mm thick in cm 1:6 complete all as specified & directed.

M & L for machine cut Kota stone slab as in skirting 20 to 25 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing including backing coat 10mm thick in cm 1:3 complete all as specified and directed.

Taking down chowkat or frames with shutter (without taking off shutters from the frames) exc 1.5sqm but n.exc 4.0 Sqm each complete all as specified and directed.

Taking down chowkat or frames with shutter (without taking off shutters from the frames) n.exc 1.5 Sqm each complete all as specified and directed.

S & F pressed steel frames of size 165mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

S & F 35 mm thick 2nd class hard wood factory made plain framed panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part 1 ) kiln seasoned and chemically pressure treated complete all as specified and directed.

M & L for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing complete all as specified.

S&F Factory made solid panel PVC moulded door shutter,28 to 30 mm thick (stiles),with 2,4 or 6 raised panel design with 2mm thick Moulded pvc sheet on front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification and drawing . complete all as specified and directed.

S&F aluminium handle cast type, anodised 125 mm size complete all as specified and directed.

S & F 100 mm long butt hing stainless steel and fixed complete all as specified and directed.

S&F aluminium, anodised barrel tower bolts of extruded section and fixed 150mm long complete all as specified and directed.

S&F aluminium, anodised barrel tower bolts of extruded section and fixed 100mm long complete all as specified and directed.

S & F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed

S & F for mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete

Supply and fixing of rubber beading door seal 40x 5mm strip in bottom of door complete all as specified and directed.

M&L for PCC type B1 1:2:4 (using 20mm aggregate ) for bed block etc.complete all as specified and directed.

M&L for PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate) as in roof padding for leveling of surface of roof complete all as specified and directed.

M&L reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) for slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves, chajjas,etc and any discription and any postion.complete all as specified and directed.

Taking down cement plaster from concrete surfaces including APP mambrane complete all as specified and directed.

M & L for 15 mm thick plaster bed on concrete surface in cement mortar 1:3 mixed with water proofing compound finished even and faircomplete all as specified and directed. Note: Water proofing comound shall be measured and paid separately as supply only

M & L for laying cement concrete tiles 25cmx25cmx22mm thick machine pressed,set jointed and pointed in neat cement slurry in floors and cut and polished over bedding layer 20mm screed in cm 1:4. the cement mortar screed shall be mixed with polymer based liquid water proofing additive @ 0.2 ltr per 50kg of cement or as per manufacture specifiedtios/ instructions and tiles joints shall be filled with 1:3 cm mixed with crude oil as per SSR-2009 (Part-I) complete all as specified and directed. Note: Water proofing comound shall be measured and paid separately as supply only

M & L for roof treatment with APP based polymeric membrane, 3mm thick (minimum), weighing 3.0 Kg/Sqm ( minimum) reinforced with polyester non woven fabric (weighing not less than 150 gms/sqm) shall be applied over and including one coat of hot blown bitumen grade 85/25 confirming to IS-702 @ 1.2 Kg per sqm over a coat of bituminous primer @ 0.3 ltre per Sqm surface, applicatioin of APP modified membrane shall be by torch application . The overlaps shall be minimum 100mm on the transverse direction and 75 mm on logitudinal direction all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick wall with mixing WPC finished even and smooth (without using extra cement ) in CM 1:3 ( sunken portion ) complete all as specified and directed. Note: Water proofing comound shall be measured and paid separately as supply only

M&L Applying bituminous primer on surfaces @ 0.30 ltr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and laying polymeric water proofing membrane 3 mm thick, weighing 3 Kg/Sqm and bonded completely to the surfaces with overlap of 10 cms (overlaps to be thermo fused by flame) and applying one coat of hot blown bitumen 85/25 @ 0.70 Kg/Sqm complete all as specified and directed. (for sunken portion)

M&L PCC (1:5:10) type E-2 (using 40mm graded aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

TMT bars 8 to 10mm dia as in stirrups cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. complete all as specified and directed

M&L Formwork to soffits of suspended slabs such as roof slabs floor slabs, landing and similar work not exceeding 200mm thick (Horizontal or Sloping) complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C1 (using 20mm graded stone agg) as in plinth protection finished even and smooth with using extra cement complete all as specified and directed.

M & L for post construction Anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

M & L for post construction Anti Termite Treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors. complete all as specified and directed.

S & F in repair Brass chromium plated, tubular towel rails 20 mm dia, D- type, 60 cm long between flanges completed all as specified and directed.

S&F in repair brass chromium plated shower roses with swivel joints, 150 mm size in square with CP long shank arm including fixing to steel pipe or union, complete all as specified and as directed.

S&F in repairs WC squatting pan “Orissa Pattern” of size 580 x 440mm white with integral foot rest (excluding flushing cistern & flush pipe) including connection to trap and to flush pipes etc and lime concrete bedding complete all as specified in SSR and including S&F trap set complete all as specified and directed.

S&F in repairs PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including dual flush ball valve float & handle, waste pipe & brackets complete set complete all as specified and directed.

S&F in repair vitreous china urinal full stall urinal (back or corner wall type ) complete including providing and fixing plugs with , bedding urinal against wall in cement mortar 1:2, securing urinal to pluges ith and including 60mm long brass screws,pointing around urinal back in cement , flush pipe, grating and unionfor discharge pipe. (Including of fixing supply pipe to flushing cistern, Urinal Spreader trap and waste pipe) complete all as specified and directed.

M&L for 20 mm thick Granite(of any type) work ( table rubbed and polished) in urinal partition etc and like fixed to wall in verticle position in cement mortar (1:4) including pointing in white cement complete all as specified and as directed by Engineer-in-charge

M&L Granite (of any type) work, 20 mm thick (Table rubbed and polished) in steps, jambs, pillars,Wash basin Shelf platforms, urinal partition in cm 1:4 and including pointing in white cement 1:2, using marble dust with admixture of pigment to match with marble shade of Granite including half moulding of granite edges including screed bed 20mm thick in cm 1:6 and driling hole for gas pipe etc.complete all as specified and directed.

S & F Vitreous China wash basin, Oval Shape counter sunk , size 600x480 white, excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

S&F in repairs concealed stop cock fancy type CP with long shank cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 15mm bore. complete all as specified and directed.

S&F in repair angle cock fancy type CP with long shank cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 15mm bore complete all as specified and directed.

S&F in repairs bib tap, cast copper alloy with capstan head, CP fancy type with long body shank, screwed down with high pressure screwed for iron pipe & fixed 15mm bore, complete all as specified and directed.

S&F in repair pillar taps,15 mm bore dia fancy type castcopper alloy, with capstan heads,chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe and fixed complete all as specified and directed.

S & F in repair 15mm bore brass CP mixer for mixing hot & cold water scrwed down for iron pipe and fixed fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed.complete all as specified and directed.

S&F in PVC connections 15mm size with PTMT nuts of length 600 mm, complete all as specified and as directed.

S&F grating doom with hole or without hole 100mm dia size with Stainless Steel complete all as specified and directed.

S&F ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed 20mm bore minimum weight 210 gms complete all as specified and as directed.

S&F in replacement rotational moulded polythene water storage tank of capacity 2000 ltrs (Cylindrical/vertical with closed top), triple layer construction, ISI marked, hoisted & fixed in position including over flow 450mm, waste pipe 600mm long with fitting etc. of 20 mm dia directed complete all as specified and as directed.

S&F Stop valves/Gate valves cast copper alloy screwed down high pressure, with crutch or butterfly handle, screwed both ends for 20mm bore dia iron pipe or for unions and fixed. complete all as specified and directed.

S&F Stop valves/Gate valves cast copper alloy screwed down high pressure, with crutch or butterfly handle, screwed both ends for 25mm bore dia iron pipe or for unions and fixed. complete all as specified and directed.

Dismantling of cast iron or reinforced drain pipe 110/75mm dia of any description complete all as specified and directed.

S&F 15 mm GI tubes medium grade with all fitting and fixed complete to walls, ceilings or laid in floors including taking up or down old steel tube .complete all as specified and directed.

S&F 20 mm GI tubes medium grade with all fitting and fixed complete to walls, ceilings or laid in floors including taking up or down old steel tube complete all as specified and directed.

S&F in repair 32 mm GI tubes medium grade and fixed complete to laid in floors complete all as specified and directed.

S & F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F 110mm PVC (SWR) WC connector socket to fit WC outlet complete all as specified and directed

S & F 110 mm pvc (SWR) vent cowl complete all as specified and directed

S & F 110mm PVC(SWR) bends (any radius ) diminishing pieces or tapers ( larger bore measured ) complete all as specified and directed.

S & F 110 mm PVC (SWR)Branch pieces single (equal or unequal ), ordinary or inverted or with paralle branches or T piece with oval access doors complete all as specified and directed.

S & F in repair stack clamps out of 50mm by 5 mm flat iron and 16 mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roofs for bore of 100mm complet all as specified and directed.

S & F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints complete all as specified and directed.

S & F 75 mm PVC(SWR) bends (any radius ) diminishing pieces or tapers ( larger bore measured ) complete all as specified and directed.

S & F 75 mm pvc (SWR) vent cowl complete all as specified and directed

S & F 75 mm PVC (SWR)Branch pieces single (equal or unequal ), ordinary or inverted or with paralle branches or T piece with oval access doors complete all as specified and directed.

S & F in repair 75mm dia cast iron Nahan trap including jointing to waste pipe fixed in cement concrete type B1 (1:2:4 ) complete all as specified and directed.

S & F in repair 100mm dia cast iron Nahani trap including jointing to waste pipe fixed in cement concrete type B1 (1:2:4 ) complete all as specified and directed.

S & F in repair 75mm dia cast iron floor trap including jointing to waste pipe fixed in cement concrete type B1 (1:2:4 ) complete all as specified and directed.

S & F 75mm dia cast iron gully trap with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4 ) complete all as specified and directed.

M & L for Providing, cement concrete type B0 (1:2:4 using 12.5mm graded stone aggregate as in coping on chajja, balcony or in roof kerbs , filling of steel pressed chowkhat, rounded or chamfered on edges and similar work complete all as specified.

M&L for preparation of new plastered surface and applying two coats of oil emulsion distemper over a coat of 3 mm thick wall care putty completed all as specified and directed.

M&L for complete removal of existing treatment of old surfaces wall and applying two coats of oil emulsion distemper over a coat of 3 mm thick wall care putty completed all as specified and directed.

M & L for preparation of new steel Surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer complete .

M & L for preparation of new wooden Surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for preparing new plaster surface of ceiling and applying two or more coats of white wash over coat of primer complete all as specified and directed.

M & L for complete removal of existing treatment on ceiling surface and applying two or more coat of White wash over a coat primer complete all as specified and directed.

M&L brick work with sub-class 'B' bricks, straight or curved on plain to any radius in half brick thick walls built in cm 1:6 complete all as specified and directed.

M&L for roof tiles mangalore pattern,interlocking at side joints over screed bed or bedding layer of mortar 20mm thick with CM 1:4 for laying floor finishes with water proofing compound etc. complete all as specified and directed. (to Chajjas)

M&L for removing loose and broken concrete by chiselling /picking etc upto a depth of 80 to 100 mm from columns, beams and similar structural members cutting edges cleaning the dismantled portion with wire brushes etc to remove dust, dirt and other foreign particles etc and washing with clean water with pressure and removal of debries to a distance not exc 50 M all as specified and directed by Engr-in-Charge, including necessary scaffolding etc complete.

M&L for removing loose and broken concrete by chiselling /picking etc upto a depth of 10 to 20 mm from floor/roof slab/chajjas and similar structural members cleaning the dismantled portion with wire brushes etc to remove dust, dirt and other foreign particles etc and washing with clean water with pressure and removal of debries to a distance not exc 50 M all as specified and directed by Engr-in-Charge, including necessary scaffolding etc complete.

M&L for applying one coat of anti corrossive primer @ 0.25 Lit/Sqm for the steel area to exposed old and new reinforcement to the full circumfrance and length of bars to form unbroken 40 Micron thick film all as specified and directed by Engr-in-Charge. Make: M/s Thermax Ltd/M/s STP Ltd/ M/s Bostik India Pvt Ltd/ M/s Asian Paints Ltd

M&L for applying one coat epoxy bonding agent @ 2.6 sqm/lit or as per manufactures instruction to old concrete surfaces all as specified and directed by Engr-in-Charge to surfaces of columns, beams and similar structural members all as specified Make: M/s Thermax Ltd/M/s STP Ltd/ M/s Bostik India Pvt Ltd/ M/s Asian Paints Ltd

M&L for non shrink, cementitous micro concrete mixed with 12.5 graded stone aggregate using Renderoc RG or equivalent by weight (18 Kg Aggregate :25 Kg Renderoc RG) respectively (as per manufatures instruction) laid in average thickness 80 to 100 mm in surfaces of columns, beams and similar structural members including use and waste of water tight form work to facilitate pouring of micro concrete all as specified and directed by Engr -in -Charge. Make :- Fosroc or Equivalent in M/s Thermax Ltd/M/s STP Ltd/ M/s Bostik India Pvt Ltd

M&L for spraying curing compound as per manufactures instruction on freshly cast concrete surfaces all as specified. Make : Concure WB white of Fosroc or equivalent

M&L for application of high build polymer cement sand mortar 1:3 with water cement ratio 0.35 to 0.45 mixing with Nito bond SBR @ 5 ltrs per 50 Kg cement on ceiling / chajja surfaces 10 to 20mm thick in two layers over slurry priming coat of 1 volume Nito bond SBR to 1 volume water, 3 volume fresh cement (5 sqm per litre Nito Bond SBR) etc all as per manufacturers instructions, including painting/finishing to match with the existing complete all as specified and as directed by Engineer-in-Charge. Make : Nitobond SBR shall from Fosroc chemical (India) Pvt Ltd or equivalent in make M/s Thermax Ltd/M/s STP Ltd/ M/s Bostik India Pvt Ltd/ M/s Asian Paints Ltd

S & F powder coated anodised aluminium frame for windows, ventilators with one or more rebates including aluminium openable shutter for window & joining cleat for fixing etc complete all as specified and directed.

S & F 4mm thick Sheet glass, ordinary quality in square in not exc 0.5 sq.m in each panel complete all as specified and directed.

S & F 4mm thick Figured glass, pin head type in squares in n exc 0.5 sq.m in each panel complete all as specified and directed.

Supply only glass beading for fixing of glass pane to aluminium window complete all specified and directed.

M&L for 3mm thick cementitious wall care putty on new/ old plater for internal ceiling wall surfaces complete all as specified and directed.

M&L for preparing new plaster surfaces of ceiling and applying two coats of oil bound distemper over coat of primer complete all as specified and directed.

M&L for complete removal of existing tratment on ceiling surface and applying two coat of oil bound distemper over a coat primer complete all as specified and directed.

M&L for complete removal of existing treatment applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm / liter and UV resistance as per IS15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre /10sqm over a coat of 3 mm putty over and including priming coat of exterior primer applied @0.90 litre/10 sqm over old surfaces.complete all as specified and directed.

M&L for preparing new surface and applying two or mor coats of 100% premium acrylic emulsion paint having VOC less than 50gm / liter and UV resistance as per IS15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre /10sqm over a coat of 3 mm putty over and including priming coat of exterior primer applied @0.90 litre/10 sqm over new surfaces.complete all as specified and directed.

Cleaning of first manholes of any description and in any position depth n’exc 1.5mtr deep mechanically or manually by taking off sludge waste/ night soil and silted soil from the existing manhole of any size, collecting and removal of sludge in sealed container out side Air Force boundary and disposal of the same complete all as specified and directed

Demolition and breaking up drain pipes 150 mm dia (Salt glazed ware, AC or Reinforced concrete) set in cement mortar as specified and directed.

S&F 160 mm dia Nu- Drain UPVC SN-4 underground pipes having wall thickness 4mm confirming to IS:15328 with ISI mark including all necessary fittings with rubber ring type socket complete all as specified and directed.

M&L for cement concrete bed (1:3:6) type C-2, using 40 mm graded to drain pipe including packing under and haunching against the side of pipe after they are laid and tested for bore of pipe 160 mm complete all as specified and directed.

Cutting into existing manholes for connecting new drains of internal dia of pipe 160mm making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required

M&L for brick work with sub class 'B' burn brick straight or curved on plan exceeding 6m mean radius using old size brick built in CM (1:4) complete all as specified and directed

M&L PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate as in coping/ benching surface channel including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for PCC (1:4:8) type D-2, using 40 mm (graded stone aggregate )as in foundation filling and mass concrete complete all as specified & directed.

M&L providing Precast Cement concrete (1:2:4) type B-1, ( 20 mm graded aggregate ) as in cover slab (for manholes, drain etc)set in cement mortar (1:4) complete all as specified and directed.

M&L for mild steel bars (TMT bars) 6-8mm dia cut to length, bent to shape required including cranking bending, spirally for hoping for columns, hooking ends and binding with and including mild steel wire not less than 0.9 mm dia, complete all as specified and directed.

Taking down carefully existing unserviceable copper/ aluminium point wiring of any description & in any position with and including pvc/steel conduit all fitting, accessories & fixtures such as switches, ceiling roses, pendants, regulators, socket, light fittings call bell, lamp holders etc and making good the disturbed surface of walls, floors, ceiling etc to match with the existing surfaces complete all as specified and directed. NOTE: Old fittings/fixtures/accessories like switch, sockets, lamp holders, regulators light fittings etc found in serviceable condition shall be removed carefully for reuse in the work and shall be paid for separately under appropriate item of Schedule `A’.

Material and labour for point wiring for one light /fan/Exhaust fan point controlled by one switch with using FRSLH1.5 Sqmm (nominal area) stranded copper conductor, single core, PVC insulated & unsheathed cable, 1100 volts grade in and including concealed PVC conduits /Casing caping (Medium grade) of size not less than 20 mm dia all as directed with sunken type pressed steel terminal box and junction boxes 1.6mm thick of suitable size, duly painted with one coat of red oxide primer and two coats of black bituminous paint for mounting fittings and wiring to be terminated in pressed steel sunken boxes with laminated top sheet of 3 mm thick for housing of switchws, sockets, regulators etc including all accessories and using 1.5 Sqmm (nominal area) stranded copper conductor single core conductor, PVC insulated & unsheathed cable as in earth wire connected to common earth dolly complete all as specified and directed. NOTE :-(I) The portion of point wiring at ceiling shall be in surface PVC conduit/ casing & caping of suitable size fixed on ceiling surface with using PVC rawl plugs. (ii) Fittings like switches, sockets, regulators, lamp holders, light fittings shall be measured and paid for separately under appropriate item of Schedule `A'. (iii) The quoted rates shall be deemed to be inclusive for provision of covering sunken boards/terminal boxes / junction boxes of any shape and size with 3mm thick laminated sheet fixed with suitable brass screws and cup washers

M & L for switch flush type single pole one way 5 Amps, 240 volts, white ivory finish complete all as specified and directed.

M&L for ceiling rose surface Bakelite two to three terminal, 18 x 50 mm complete all as specified and directed.

Supply & Fix for decorative slim linear LED tube light fitting 01x20 watt light with co extruded polycarbonate body, environmental frendly, energy efficient ready to use pack with all accessories including 01 No 20 watt tube rod and connecting the same to ceiling rose with using copper conductor 24/0.20 flexible PVC sheathsd and fixing arrangement for fixing the light fitting to wall/ roof surface complete all as specified & directed by Engineer in-charge

Dismaintling & Taking out MCB DBs VTPN with all MCB's/Isolator & metal clade box any size , any type and capacity complete all as specified and directed.

Supply and fixing of sheet metal enclosure Double door for DB’s 8 way 240 volts with 200 Amps rated bus bar for single phase and neutral supply complete fixed properly on in concealed position and to connect their incoming/outgoing electric connections by means of suitable sizes of lugs/thimbles and to provide required sizes of flexible conduit at any open surfaces near DB’s of cables/wires complete all as specified and directed.

Dismaintling & Taking out MCB's/Isolator/MCCB any size , any type and capacity complete all as specified and directed.

S&F MCB single pole 6 to 32 Amps, 10 KA ,240 Volts complete all as specified and directed.

S&F MCB Single pole and neutral 63 Amps, 240 Volts complete all as specified and directed.

Disconnecting & taking up or down unserviceable sub main wiring of aluminium/Copper conductor with two run of single core cable and one run of single core earth cable of any description, any size & in any position including taking out existing conduits of any description and making good the disturbed surfaces to the existing surfaces all as specified and directed. NOTE: Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit.

M&L for sub main wiring using two single core PVC insulated, unsheathed stranded copper conductor cable of size 6.0 Sqmm of voltage rating upto and including 1100 Volts grade in and including conceled /casing caping PVC conduit, med grade of size not less then 25 mm bore along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 6.00 Sqmm as earth continuity conductor all as specified and directed. NOTE : (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit. (ii) The quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface complete all as specified and directed.

S&F exhaust fan stell body AC single pahse 230V of size 450mm sweep heavy duty with blades and frame and louvers all accessories as specified and directed.

M/S Amit Traders

M/S NIRMAL SINGH DHANJAL

m/s vikash Engineers

YASH DEVELOPERS AND CONSTRUCTION COMPANY