SPECIAL REPAIR FOR REPLACEMENT OF BARBED WIRE FENCING WITH 2X2 CHAIN LINK FENCING IN THE PERIMETER OF MH AMRITSAR SPECIAL REPAIR TO BLDG NO P1A PATIENTS COOK HOUSE AT MH AND ADDN ALTN OF BLDG NO P16 P 01 H6 NEAR MES IB AT OAC

Amount

Excavating in post holes (or similar holes) each hole not exceeding 0.5 Cum, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and remvoing surplus soil to a distance not exceeding 50m and making good surfaces in any type of soil complete all as specified & directed by the Engineer-in-Charge.

Dismantling posts or struts (wood,steel or RCC ) any section , incl taking out embedded portion in concrete , brickwork or masonory and making good distributed ground complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for mild steel work in posts and struts in fencing including cutting tops to shape as directed, notching for wires etc, flat iron fillets ( for securing wire mesh etc) including all necessary drilling, bolting and rivetting etc conforming to FE-290 Gde E-165 ; complete all as specified & directed by the Engineer-in-Charge.

Material & labour for cement concrete 1:3:6, type C-2 (using 40 mm graded crushed stone aggregates) as in foundation filling , mass concrete & post holes concrete etc complete all as specified & directed by the Engineer-in-Charge.

Dismantling GI barbed wire from RCC or Steel posts complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc , including dismantling old unserviceable barbed wire from RCC or Steel posts complete all as specified & directed by the Engineer-in-Charge. Note :- Each line wire to be measured

Supply and Fixing for chain link fencing mild steel galvanisd fencing, any size or type including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified & directed by the Engineer-in-Charge. Chain link complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long, dia of neck 5 to 10mm complete all as specified & directed by the Engineer-in-Charge.

Material & labour for 10mm dia and over mild steel round bars, Fe-410, for securing wire mesh , chain link fencing etc ; complete all as specified & directed by the Engineer-in-Charge.

Material & labour for mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed ) not less than 0.9mm dia or securing with clips ; complete all as specified & directed by the Engineer-in-Charge.

Material & labour for 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed ) not less than 0.9mm dia or securing with clip ; complete all as specified & directed by the Engineer-in-Charge.

Material & labour for two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer , icluding preparation of new or previously untreated steel surface of any description over 10cm in width or girth , not otherwise described ; complete all as specified & directed by the Engineer-in-Charge.

Demolition of brick work built in cement mortar, including all quoins, arches, pillars etc ; complete all as specified & directed by the Engineer-in-Charge.

Material and labour for brick work with sub-class 'B' bricks straight or curved on plan exceeding 6 metres mean radius built in cement mortar 1:4 ; complete all as specified & directed by the Engineer-in-Charge.

All as per item No.15 here-in-above but except bricks (old serviceable bricks obtained from demolition shall be reused after necessary cleaning of mortar) : complete all as specified & directed by the Engineer-in-Charge.

Material and labour for brick work with sub-class 'B' bricks old size bricks, in half brick thick wall built in cement mortar 1:3 ; complete all as specified & directed by the Engineer-in-Charge.

Material and Labour for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of colour approved by the GE, having tensile strength of 550 Mpa as in view cutter, fixed with self tapping screws ; complete all as specified & directed by the Engineer-in-Charge.

Excavating in trenches n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 Sqm on plan and n exc 1.5m in depth and getting out in any type of soil complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for Cement concrete in foundations filling and mass concrete Type D2 1:4:8 ( 40 mm graded aggregates ) complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for RCC 1:2:4 type B1 (20 mm graded stone aggregate) nominal mix in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for RCC 1:2:4 type BI (20 mm graded stone aggregate) nominal mix in columns,pillar,piers,post and struts complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for Steel gate of angle or other section with gusset plate, rails, braces etc complete to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening and fixing complete all as specified & directed by the Engineer-in-Charge.

Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and matt beams sides and soffits (if any) of foundation and plinth beams; and similar work ; vertical or to batter or flat complete all as specified & directed by the Engineer-in-Charge.

Use and waste formwork to sides of pillars. posts. struts. piers. columns and stanchions for fair finished surfaces of concrete, square complete all as specified & directed by the Engineer-in-Charge.

Material & Labour forrendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for preparation of newly plaster surface and applying two coats of cement based paints complete all as specified and directed.

Material & Labour forGranite of any type work (table rubbed and polished) 18-20mm thick in steps, jambs, pillars, window cill, cooking platform and like in CM 1:4 and pointing with white cement 1:2 using marble dust with admixture of pigment to match the shade of granite over and incl 15 mm thick rendering in CM 1:4 including demolition of old stone slabs complete all as specified & directed by the Engineer-in-Charge.

Returning,filling in,spreading,levelling,watering and well ramming in layers not exc 25cm thick each in soft/loose soil,complete all as specified & directed by the Engineer-in-Charge.

Removing excavated material to a distance exc 250mtr b anut n.exc 500 mtr and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified complete all as specified & directed by the Engineer-in-Charge.

Dismantling Brick tiles or terracing tiles, single layer on roofs ; Complete all as specified and as directed by Engineer-in-Charge.

Demolition mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) as in padding concrete fair finish, roof kerbs or mud stops, rounded or chamfered on edges and like including weathering slight rounded and throating ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm including cleaning surfaces etc ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing (minimum) 3mm thick APP film based poly meric membrance minimum weighing 3Kg per Sqm reinforced with polyester non wove fabric (weight not less than 150 gms/sqm) land on primed surface by forced application over entire roof area with over lapping 100mm to either sides and sealed in after cleaning down the roof by brooms ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for 40mm thick brick tiles, laid on and including 15 mm thick cement mortar 1:6 and joints grouted and pointed flush in CM 1:3 mixed with 5% crude oil by weight of cement ; Complete all as specified and as directed by Engineer-in-Charge.

All as per Srl Item No. 35 here-in-before but except brick tiles complete all as specified & directed by the Engineer-in-Charge. Note:-Old serviceable tiles shall be reusedall.

Material & Labour for PCC 1:1.5:3 type B0 using 12.5 mm graded stone aggregate for repair of Chajja, Fascia, parapets etc using chicken wiremes upto 8 m height including necessary formwork, scaffolding. And applying two coats of cement base paint over coat of primer over cement plaster 1:4 complete all as specified & directed by the Engineer-in-Charge.

Dismantling Asbestos cement ( corrugated, semicorrugated ,etc.) sheets in roof coverings complete all as specified & directed by the Engineer-in-Charge.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified & directed by the Engineer-in-Charge.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed by the Engineer-in-Charge.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St. 240 complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for two coats of synthetic enamel painting on steel surfaces of any description over 10 cm in width or girth not otherwise described over a coat of red oxide primer including prepration of previously untreated surfaces complete all as specified & directed by the Engineer-in-Charge.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc.Laid, bedded and pointed in any mortar complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for Machine cut Kota stone slab flooring 20-25 mm thick (size not less than 0.5 sqm each) over cement screed base of 15mm thick in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & directed by the Engineer-in-Charge.

All as per srl Item No 16 here-in-before but as skirting/dado over rendering 10mm thick in CM 1:4 complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for rubbing/grinding and polishing of Kota stone/Marble tiles/Granite(of any type)/Cudappah stone flooring complete all as specified and directed by Engineer in charge.

Demolition of cement concrete in ground floors and paving not exceeding 15 cm thickness ( below or above ground level) and disposing the rubbish to a distance exceeding 50 Mtr but not exceeding 100 Mtr away to low lying areas complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) in sub base of floor complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for 50mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate as in plinth protection Finishing fair and even complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for Chequered cement concrete tiles 30cm x 30cm x 25mm thick over and including 15mm thick bedding layer in cement mortar 1:6,set and jointed in neat cement slurry and pointed in grey cement and pigment to match the colour of tiles complete all as specified and directed by Engr-in-charge.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified & directed by the Engineer-in-Charge.

Demolition of brickwork, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for brick work with sub class "B" bricks (old size) straight or curved on plan exc 6 m mean radius, built in CM 1:6 complete all as specified & directed by the Engineer-in-Charge.

All as per Srl item No 26 above but except bricks (old dismantled serviceable bricks obtained from Srl item No 5 shall be reused after necessary cleaning of mortar) : complete all as specified & directed by the Engineer-in-Charge.

Taking down cement plaster of any description on brick walls, etc including raking out joints, hacking for key scrubbing down with water etc complete all complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for rendering 15 mm thick on brick work or concrete surfaces on walls in CM 1:6 finishing even and smooth without using extra cement complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for rendering 15 mm thick on brick work or concrete surfaces on walls in CM 1:4 finishing even and smooth without using extra cement complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for rendering 10 mm thick on brick work or concrete surfaces on ceiling in CM 1:3 finishing even and smooth without using extra cement complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for applying two coats of whitewash on ceiling including preperation of newly plastered/old decorated surfaces complete all as specified & directed by the Engineer-in-Charge.

Material and labour preparation of newly plastered surface of wall and Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for applying two coats of colourwash on wall including preperation of newly plastered/old decorated surfaces complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for preparation of NEW plastered surfaces and applying two coats of cement base paint paint over a coat of cement primer on wall surfaces complete all as specified & directed by the Engineer-in-Charge.

Hacking out old broken glass from wooden/ steel window cleaning the surface and removing from the site, thenafter Supply & Fixing for clear glass, 3mm thick ordinary quality, in any shape, not exceeding 0.50 sqm in each pane including and glazing with oil putty/wooden beading as per site requiremnets complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for repair Helical door spring 300mm, ordinary rat tail rod pattern springs, including roller and roller plate fixed to iron chowkats with weildingcomplete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for factory made 30 mm thick flush shutters solid core construction with block board core and plywood face panels complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for IInd class hard wood Glazed and skeleton shutters 35mm thick divided into square, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (a) ; supplied and fitted to chowkats complete all as specified & directed by the Engineer-in-Charge.

Material and Labour for Box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame ( single rebated), comprises glazed shutter, frame of ERW tube and FI 2mm thick welded/screwed to frame for fixing of sheet glass including fixture and fittings like as Stopper, Cleat, Pintal hinges, holdfast etc all as shown on drg No CEJZ/TD1019/08 sheet 1/3 to 3/3 dt 01 May 2008 complete all as specified. NOTE:-Sheet glass and painting shall be measured and paid Separately complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for two coats of synthetic enamel painting on wooden surfaces of any description over 10 cm in width or girth not otherwise described above pink primer including prepration of previously untreated surfaces complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for apply One coat of synthetic enamel pain on steel surfaces of any description over 10 cm in width or girth not otherwise described including prepration of OLD surfaces complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for one coat of synthetic enamel painting on wooden surfaces of any description over 10 cm in width or girth not otherwise described including prepration of OLD surfaces complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for 300mm long Aluminium alloy, Anodised, sliding door bolt with hasp, staple ( bolt type) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for Aluminium, anodised, barrel tower bolts 150mm of extruded section and fixed complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for 150mm long Aluminium handles, cast type anodised complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for stainless steel butt Hinges, 100mm size, medium weight, cold rolled mild steel complete all as specified & directed by the Engineer-in-Charge.

Taking down chowkhat with shuttering (without taking off shutters from frame including grill & guard bars) size of shutter not exceeding 1.5 sqm each complete all as specified & directed by the Engineer-in-Charge.

All as per Srl item No 49 above but size of opening exceeding 1.5 Sqmtr and not exceeding 4 Sqmtr complete all as specified & directed by the Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for non skid ceramic light coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles over and including 15mm thick screed bed in CM 1:6 & complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for glazed ceramic coloured tiles 450x300mmx6mm thick, etc. on vertical surfaces such as skirting , dados and risers to steps etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match over and including 10mm thick rendering plaster in CM 1:4 on brick surface complete all as specified & directed by the Engineer-in-Charge.

Material & Labour forGranite (of any type) work (table rubbed and polished) 20mm thick in steps , jambs, pillars, window cills, cooking plateforms and like in cemnet mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick rendering in CM 1:4 complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing rotational moulded polythene water storage tanks of 1000 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-1 including Ball valves high pressure PTMT with epoxy coated Aluminium rod & High density plastic ball screwed for iron pipe and fixed to GI pipe of 20mm bore complete all as specified & directed by the Engineer-in-Charge.

Demolition of reinforced cement concrete as in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified & directed by the Engineer-in-Charge.

Material & Labour forRCC(Nominal Mix) type B1 1:2:4 (20mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) of fair finished surfaces of concrete complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for providing precast cement concrete type B1, 1:2:4 (20mm graded stone aggregate) in landings, cover slabs (for man holes etc.) chulla hoods, chajjas, ater troughs, mangers, shelves and similar articles with plain faces complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for 15mm bore tubes (medium grade) galvanised with all fittings and fixed to walls and ceiling or laid in floors complete including taking down complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for 20mm bore tubes (medium grade) galvanised with all fittings and fixed to walls and ceiling or laid in floors complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for in repair of brass cromium brass plated fancy type bib taps 15 mm bore long nose screwed down screwed for iron pipe or for brass complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for stainless steel kitchen sink with draining board made of 1mm thick sheet for kitchen with plug washers wate pipe cast iron canti lever bracket ovre all size 915 x 460mm with bowlsize 410x310x160mm complete all as specified and directed. Make- Nirali complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for in repairs vitreous china wash hand basin white with flat back type size 550x400mm excluding taps chain and plug and porcelain stopper but including brackets CP waste coupling 32mm and PVC waste pipe 32mm dia including cutting for and pinning ends of brackerts complete all as specified,Make: CERA/Jaquar/Somany/Parryware complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for in repairs pillar taps 15mm dia cast copper alloy with capstan heads chromium plated screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipes. Make: CERA/Jaquar/Somany/ Parryware : complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for in repair PVC (SWR) pipe 75mm dia fixed in wall/floor complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for in repair PVC (SWR) pipes single110mm socketed, in any length with rubber ring joints, laid in trenches or in floors/wall complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for in repair 75mm PVC (SWR) bends any radius complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for in repair 110mm PVC (SWR) bends any radius complete all as specified & directed by the Engineer-in-Charge.

Dismantling of roof brick tiles fixed in cement mortar in single layer complete all as specified & directed by the Engineer-in-Charge.

Demolition mud phuska in roofs any thickness including plastering and leeping complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) in bed blocks for hold fast & similar work etc complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in roof padding (avg 40mm thick), roof kerbs or mud stops, rounded or chamfered on edge complete all as specified & directed by the Engineer-in-Charge.

Material and labour for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by forced application over a tack coat of in dustrial bitumen 85/25 at the rate of 1.6 kg per sq.m including cleaning surfaces and including 10 mm thck 1: 4 cement plaster on padding surface complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for 40 mm thick brick tiles laid on 15mm thick cement mortar 1:6 and joints grouted flush in cement mortar ( 1:3) mixed with 5 % of crude oil by weight of cement complete all as specified & directed by the Engineer-in-Charge.

All a per Srl item 06 here-in-before but except tiles (old serviceable tiles obtained from dismantling) shall be reused after necessary cleaning of mortar) complete all as specified & directed by the Engineer-in-Charge.

Taking down cement plaster on brick, concrete or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. Of any description complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for 15mm thick cement plastering in cm 1:6 on brick or concrete surfaces other than fair surface, finished the surfaces even and fair without using extra cement complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for 05mm thick cement plastering in CM 1:3 on ceiling surfaces other than fair surface, finished the surfaces even and fair without using extra cement complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for Rendering 15 mm thick on fair/unfair faces of brick work or concrete surfaces in CM 1:4 and to be finished even and smooth ( without using extra lime or cement) including WPC @ 3 % weight of cement etc complete all as specified & directed by the Engineer-in-Charge. Note : WPC will be measured and paid separately under appropriate items.

Material & Labour for finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) including preparation of new surfaces complete all as specified & directed by the Engineer-in-Charge.

Supply only liquid water proofing compound, ISI marked complete all as specified & directed by the Engineer-in-Charge.

Material & Labour forpreparation of new plaster surface and applying two coat of white wash on ceiling complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for Complete removal and preparation of existing treatmnet of plastered surfaces on walls applying two coats of Oil bound distemper over a coat of primer complete all as specified & directed by the Engineer-in-Charge.

Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter for the chowkats ) complete all as specified & directed by the Engineer-in-Charge.

-ditto- but exc 1.50sqm but n.exc 4 Sqm (including CB shutters with chowkhat) complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for pressed steel frames 1.25mm thick for door size of frame 125 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges complete all as specified and directed complete all as specified & directed by the Engineer-in-Charge.

ditto but one or more rebate and size 105x60 mm complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for factory made 35 mm thick flush shutters solid core construction with block board core and plywood face panels complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for IInd class hard wood Glazed and skeleton shutters 35mm thick divided into square, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (a) ; supplied and fitted to chowkats complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for mild steel work Fe 410-W(Gde-E- 250) quality-A Fe in framed work as in door frame, shutter or gates of angle iron or other section with gusset plates,rails,braces etc complete drilled for fixing of steel sheeting or orther covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for in repair for 18-19mm thick Block Boards, grade 2 quality , interior grade, commercial type, fixed with screws to timber frame work or supports as in shelves and similar work complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for aluminium anodised barel tower bolt of extrud sec 150mm long ISI marked complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for extruded aluminium alloy handle fabricated type anodized of size 150 mm long ISI marked complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for 300mm long aluminium alloy,anodised ,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet,cast or extruded section and fixing bolts and sliding bolts of extruded sectionsor cast aluminium alloy complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for 300mm, mild steel ordinary rat tail rod pattern springs,including roller and roller plate complete. Note : Repair required on steel door frame, welding to be carried out or necessary alternative arrangements to be complete all as specified & directed by the Engineer-in-Charge.

Material and Labour for Box type steel window made of ERW tube P- section of size 60 mm x 25 mm double rebated outer frame, comprises glazed skelton & gauzed shutter of ERW tube P-Section size 50mm x 20mm with one/two Nos openable leaf for each shutter consisting of two Nos Sashbar of T-section 20 x 3 mm welded to frame with one No verticle mullion of ERW box type T Section of size 60mm x 25mm and FI 2mm thick welded/screwed to frame for fixing of glass including fittings and fixture like as Handle, Tower Bolt, Stopper, Cleat, Pintal hinges, holdfast etc as given below all as shown on drg No CEJZ/TD-1020/08 Sh 1/3 to 3/3 dt 01 May 2008 complete all as specified and directed.(a) Hold fast 150mm long of 12mm x 3mm MS flat - 4 Nos per Window.(b) Handle of Z section 20mm x 25mm, 100mm long- 01 No per leaf.(c) MS tower bolt 150mm long - 02 Nos/leaf.(d) Z Section stopper 20mm x 25mm, 100mm long - 01 No per leaf.(e) Cleat 55mm long of hollow square 15mmx12mm - 02 Nos per leaf.(f) MS pintol hinges size 75mmx12mm - 2 Nos per leaf Note :- Sheet glass, wire mesh and painting shall be measured and paid sperately : complete all as specified & directed by the Engineer-in-Charge.

Material and Labour for Box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame ( single rebated), comprises glazed shutter, frame of ERW tube and FI 2mm thick welded/screwed to frame for fixing of sheet glass including fixture and fittings like as Stopper, Cleat, Pintal hinges, holdfast etc all as shown on drg No CEJZ/TD1019/08 sheet 1/3 to 3/3 dt 01 May 2008 complete all as specified. NOTE:-Sheet glass and painting shall be measured and paid Separately : complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for figured glass pin head type, 3mm thick ordinary quality, in any shape, not exceeding 0.50 sqm in each pane including and glazing with oil putty complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for rotational moulded polytheylene triple layered white water storage tanks of capacity 500 Litres (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of existing water tank and 20mm dia brass float valve with brass rod complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for clear glass, 3mm thick ordinary quality, in any shape, not exceeding 0.50 sqm in each pane including and glazing with oil putty complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for in repair stop value 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified & directed by the Engineer-in-Charge.

Taking up and down GI pipe15mm bore including fittings, connection, including cleaning for refixing in any position complete all as specified & directed by the Engineer-in-Charge.

-ditto- but 20mm bore of pipe : complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for GI tubing 15mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for GI tubing 20mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for in repair bib taps 15mm dia chromium plated fancy type with capstan head screwed down screwed for iron pipe or for brass ferrule and fixed in repairs complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for in repair stop valves(Concealed cock) 15mm bore chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for in repair stop valve/angel valves 15mm bore chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for in repair CP shower rose 125 mm size with swivel joint fancy type including fixing to steel pipe or union complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with internal foot rest with `P’ or `S’ trap, integral foot rest including water connection to trap and flushing pipe, flushing cistern etc including lime concrete in lime mortor 1:3 usisng broken bricks 40mm graded coarse aggregate complete all as specified & directed by the Engineer-in-Charge. Note:- Flush pipe and flushing cistern to be measured and paid separately.

Supply & Fixing for repair PVC low level flushing cistern 10ltr capacity, with syphonic action PVC float valve, brackets and 32mm bore PVC flush pipe etc complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for in repair PVC connections 15 mm size with PTMT nuts of length 600 mmcomplete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for in repair Vitreous china wash basin(with pedastal),white flat back,size 550x400mm excluding taps but including brackets,32 mm waste pipe and 32mm brass(CP) waste couplingcomplete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for in repair Pillar taps 15mm bore, cast copper alloy but fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for brass chromium plated towel rail `D’ type 60 cm long fixed to wall complete all as specified & directed by the Engineer-in-Charge.

Dismantling of cast iron ,PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches , if required complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for 110mm bore PVC (SWR) ISI marks pipes single socketed in any length with rubber ring joints fixed to wall or floor complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to walls or floor complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for PVC (SWR ) bends with access door 75 mm bore any radius complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for PVC (SWR ) bends with access door 110 mm bore any radius complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for PVC (SWR ) vent cowl 110 mm bore complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for PVC (SWR ) floor trap 75 mm plain with grating incl. jointing with solvent cement as per site requirement complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for Stack clamps (110 mm pipe) out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified & directed by the Engineer-in-Charge.

Ditto but 75 mm complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for preparation of new painted wooden surface exc 10cm width or girth and applying two coat of synthetic enamel paint over one coat of primer complete all as specified & directed by the Engineer-in-Charge.

Supply and fixing in repair cutrain rod 20mm dia of SS with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plug including SS bracket fixed to wall and with SS knobs complete all as specified & directed by the Engineer-in-Charge.

Demolation of brick work built in cement mortar or cement lime mortar as cutting, opening of exsiting wall complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for brick work with sub class "B" bricks (old size) straight or curved on plan exc 6 m mean radius, built in CM 1:6 complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for brick work with sub class "B" bricks (old size) straight or curved on plan exc 6 m mean radius, in half brick thick walls and built in CM 1:4 complete all as specified & directed by the Engineer-in-Charge.

Demolition of cement concrete in ground floor & paving n.exc 15cm above ground level complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for75mm thick PCC 1:3:6 type C 2 as in plinth protection finishing the surface even and fair with out using extra cement laid to a slope of 1 to 20. It shall be laid in alternate bays, each bay not exceeding 3 m in length with joint to be filled with bituminous mastic filling comprising of misture of one part of heated not blown bitumen 85/25 penetration and three parts of heated sand complete all as specified & directed by the Engineer-in-Charge.

Roughning the surface of old concrete floor picking sweeping clean and washing down with water to remove dust/mud etc.and brushing neat cement slurry @ 3kg/Sqmcomplete complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified & directed by the Engineer-in-Charge.

M& L Non skid coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) size 400mmx400mm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in cm 1:6 ccomplete all as specified & directed by the Engineer-in-Charge.

All as per Ser item No 169 here-in-before but as in skirting over 10mm thick cement plaster in 1:4 complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for glazed ceramic coloured tiles in vertical surface of size 450x350x6-7mm thick joint free on and incl 10mm thick screed bed in cm(1:4)set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles complete all as speciifed and directed by EIC complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for preparation of old steel surfaces and applying one coats of synthetic enamel paint over zinc chromate primer including preparation of steel surfaces complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for two coats of synthetic enamel paint over one coat of primer (red oxide)on steel surfaces exceeding 10cm width or girth incl preparation of surface complete all as specified & directed by the Engineer-in-Charge.

Supply & Fixing for mild steel framed work such as grills,grating ,etc with ends of bars , just as in doors, ventilators, and as in hold fast,ladders,railings,Framed Guard bar ,railings etc with ends of bars shouldered and/or riveted complete welded hinged and similar work Conforming to Fe-290 Gde-E-165 complete all as specified and directed by Engr-In-Charge.

Supply & Fixing for mild steel cold rolled medium weight butt hinges 100mm size fixed screws to wooden frames or with welding to steel frames complete all as specified & directed by the Engineer-in-Charge.

AC/SRW(BLDG)-01/2024-25 & ASR/REV-06/2024-25 Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials and making good disturbed surfaces of walls, floors, etc.complete all as directed

Material & Labour for point wiring complete with 1.5 sqmm single core PVC insulated sheathed multi-stranded, copper conductor FRLS grade cable of 1100 volts grade conforming to IS:694 drawn through and including non metalic rigid PVC conduit, medium grade, ISI marked, not less than 20mm bore with conduit accessories concealed on wall and ceiling/roof etc, with provn for fixing modular metal flush boxes not less than 1.0 mm thick of suitable modules, concealed in walls with modular white plated cover as top cover fixed with screws for housing switches, socket outlets, fan regulators etc, including provn of 1.5 sqmm nominal cross sectional area, PVC insulated, FRLS, sheathed, 1100 volt grade,multistranded single core green colour copper conductor for earth continuity connected to earth dolly complete all as specified & directed by the Engineer-in-Charge. NOTE: (i) Modular metal flush boxes concealed in wall with suitable cover plate for mounting switch, sockets, regulator etc. and cost of cutting chases & making good as existing to disturbed surface with cement mortar, if required any shall be deemed to included in the quoted rates. (ii) Modular fittings/fixtures such as switch, socket, regulator, etc., shall be measured and paid separately as under relevant item. (a) One light point controlled by one switch

All as per item no.177 above but point wiring for One Fan point controlled by one switch & regulator complete all as specified & directed by the Engineer-in-Charge.

All as per item no.177 above but point wiring for One 5 Amps outlet point on same board with other switches/sockets complete all as specified & directed by the Engineer-in-Charge.

All as per item no.177 above but point wiring for One 3 pin 5 Amps socket outlet on independent board complete all as specified & directed by the Engineer-in-Charge.

All as per ser item No. 177 here in above but point wiring with 4.0 Sqmm FRLS cable and 4.0 sqmm cable earth continuity wire for one 3 pin socket outlet,15 Amps on independent board.

Supply & Fixing for modular switch 1 way 6A, 240 volts, 1 module complete all as specified and directed

Supply & Fixing for modular switch 1 way 16A, 240 volts, 1 module complete all as specified and directed

Supply & Fixing for modular socket, 6A, 240 volts, 2/3 pin combined 2 module, flush type all as specified and directed

Supply & Fixing for modular socket, 6A/16A, 240 volts, 2/3 pin combined 2 module flush type all as specified and directed

Supply & Fixing for ceiling rose surface PVC/Polycarbonate, isolated body with face Bakelite 65x50 mm three terminal complete all as specified

Supply & Fixing for modular fan step regulator, 2 module, 240 Volts, 50 Hz, suitable for ceiling fan 1200 mm sweep all as directed

Supply & Fixing for Lamp holder angular type, PVC/Polycarbonate type with back plate suitable for batten fittings including 10cm x 10cm presto plastic board for resting to holder including S&F 01 x 10/12 watts LED lamp, 230 volts complete all as specified and directed

Supply & Fixing for LED lights fitting 1x 20W, 220V, AC, 5700K, decorative box type with driver, double sided connection, CRI> 80, PF>95%, THD<10%, Lumen>2100 lm including LED tube light of make: Havells or equivalent in Philips/Crompton, connecting up with 3 core flexible copper conductor cable (1.0 mm² size/core) from ceiling rose complete all as specified and directed.

Supply & Fixing for Wall mounted, indoor, Mirror Light LED with aluminium die cast, suitable for and including 10 watt 6000K, WH LED light, prewired incl connecting up complete all as specified and directed.

Supply & Fixing for PLUTO NEO LED luminaire 600 mm x 600 mm, 40 watt, 220 V AC recessed type of make: Havells or equivalent make of Philips/Crompton, with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases (1.0 mm² size/core) complete all as specified and directed.

Supply & Fixing for Dusk & dawn roadway luminaries 35 Watt, 230 V AC, 5700K outdoor type with epoxy black powder coated sheet of make: Havells or equivalent make of Philips/Crompton, high pressure die-cast aluminum hosing and heat resistant complete with impact and corrosion resistant including thermal management in multiple optics, PF>95%, THD<10%, Lumen>4500 lm with IP 65/66 protection complete incl connecting wire with flexible PVC insulated copper cables from ceiling rose to fitting including driver, lamp bracket made of 32mm bore galvanised iron light grade pipe made to shape having overall length not exceeding 1.5 mtr, through mild steel clamp of 25mm width and four Nos. nuts, bolts & washers of 12mm dia, 100mm long fixed to wall with all other fittings complete and testing all as specified and directed.

Taking down carefully existing serviceable Ceiling fan, ceiling cable end, etc., removing the fan for keeping in safe custody, hanging the ceiling fan with down rod after rewiring including clamps, hooks, holdfasteners etc and connecting up, including making electric connection from ceiling rose to fan complete all as directed

Supply & Fixing for exhaust fan, heavy duty, steel body AC single Phase, 230V of size 450mm sweep, with blades and frame and louvers of make: Havells or equivalent Crompton/Orient complete fixed to wall with suitable MS bolts, grouted to wall including connecting up with & including 3 core flexible copper conductor cable from ceiling rose to exhaust fan complete all as specified and directed

Taking down carefully existing serviceable Geysers of capacity 25 ltrs, ceiling cable end, etc., removing the geyser for keeping in safe custody and refixing geyser with provn of new suitable MS bolts, PVC steel braided inlet/outlet connection pipe 15mm dia, 450mm long with two numbers brass union, NRV, grouted to wall and connecting up including provn of new 3 core sheathed multi-stranded flexible copper conductor cable, writing MES No. including making good to the disturbed surface including cleaning of element, flanges, tank etc. and testing complete all as directed

Supply & Fixing for distribution board made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, SPN 12 way, 240 volts grade with 200 Amps insulated rated bus bar with nickel plated brass, isolated neutral bar and door earthing, earth bar IP- 43 protection with poly urithene (PU) gasketing, IK-08 Mechanical impact resistance, flush to wall, including testing suitable for fixing MCB SPN, SP etc, complete all as directed NOTE: (i) MCB DB & MCBs should be of same make as mentioned above. (ii) Necessary blank plates if required any to cover the blank MCB's place in DB and the rate shall be deemed to included in the quoted rates.

Supply & Fixing for MCB of SP 5 to 32 Amps current carrying capacity, 240V, 10KA 'C' curve, ISI marked, fixed in the MCB DB complete conforming to IS/IEC-60898-1 2002 with connection testing and commissioning including taking down old unsv one from the site complete all as directed

Supply & Fixing for MCB of SPN 32 Amps current carrying capacity, 240V, 10KA 'C' curve, ISI marked, fixed in the MCB DB complete conforming to IS/IEC-60898-1 2002 with connection testing and commissioning including taking down old unsv one from the site complete all as directed

Supply and fixing for sub main wiring with 2 runs of 6.0 sqmm single core, multi-stranded PVC insulated, FRLS unsheathed cable 1100 Volts grade with copper conductor drawn through and including concealed non metalic PVC conduit, medium grade, ISI marked, suitable size with conduit fittings and accessories concealed in wall/ceiling/floor including 1 run of 6.0 Sqmm multistranded PVC insulated FRLS, copper conductor cable as earth continuity conductor and connecting to common earth dolly incl taking down old unsv one from site complete all as directed NOTE: Two runs of 6.0 sqmm copper cable and one run of 6.0 sqmm copper cable alongwith non metallic PVC conduit/conduit accessories will be measured as one unit length

Supply and fixing for loadline distribution board, vertical, made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, VTPN 4 way, 415 volts grade with insulated rated bus bar assembly with isolated neutral bar,door earthing, earth bar IP- 43 protection with poly urithene (PU) gasketing, IK-08 Mechanical impact resistance, door earthing flush to wall, including testing suitable for fixing MCCB, MCB TPN/TP/SPN/SP etc, complete incl taking down old unsv one from site complete all as directed

Supply and fixing for MCCB triple pole and neutral (four pole) 160 Amps, 415 volts, 50 Hz, having thermal setting range 70% to 100% and adjustable magnetic setting and breaking capacity 25 KA including making incoming and outgoing connections complete incl taking down old unsv one from site complete all as directed

Material & labour for Earthing complete in replacement with galvanised iron mild steel earth plate electrode 60 cm x 60 cm x 6.3mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with top edge of earth plate at a depth of not less than 1.5 m below normal ground level, connected to glavanised earth lead of GI wire of size 4mm dia by means of GI Bolts, Nuts, check nuts & washers and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 25mm dia from earth plate to Panel/DBs and water pipe 20mm dia GI medium grade from top of the earth electrode raised upto a level of 50cm above ground level, MS funnel with wire mesh embeded in earthing pit of size 30x30x30cm in PCC (1:3:6) type C-1 incl exposed surfaces smoth finished with 15mm thick cement mortar (1:6), RCC pre-cast (1:2:4 type B-1) cover slab of 40mm thick with 2 Nos. MS handles of 12mm dia suitable for carrying of pit cover, Angle iron frame made out of 40x40x4mm angle iron for 30x30mm PCC pit for holding the pit cover including providing charcoal or coke and salt in alternative layers of 15 cm including necessary earth work in soft/loose soil, returning, refilling and removing of surplus soil to a distance n. exc. 50 mtr testing complete all as shown in electrical plate No-3 of MES Schedule Part-I of SSR-2009 complete all as specified and directed. NOTE: (a) Cost of excavation, earth work, watering pipe, test point, MS Funnel with wire mesh and PCC pit with cover will be deemed to be included in the quoted rate. No extra cost shall be paid to the contractor against these items. (b) On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor & no extra cost will be given to the contractor.

Supply and Laying in trenches/drawn through pipes or in road crossings/paths/drains/ ducts/floors/along poles/equipments etc., of LT cable under ground, heavy duty, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade of 35 Sqmm 3½ core cross sectional areas including connecting up using suitable size aluminium lugs testing and commissioning complete all as specified and directed. NOTE: Excavation, earthwork, cable protection pipe shall be measured and paid separately

Supply & laying double wall corrugated (DWC) high density poly ethylene (HDPE) of size 40mm dia including all necessary fittings, PN-4 rating, pressure 6 Kgf/cm², conforming to IS-16205 (Part-24) with high ring stiffness & cursh resistance capacity, etc., laid in trench for protection of submersible flat cable complete all as directed.

Excavating in trenches not exceeding 1.5 meter wide and not exceeding 1.5 meter in depth for foundation for erection of poles, stays, laying cables, stays etc and getting out in soft/loose soil and in road cutting all as specified and as directed

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm in soft/loose soil all as specified and directed

Removing excavated material/surplus soil not exceeding 50 meters and depositing where directed at a level not exceeding 1.5 meter above starting point

Supply and fixing Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified and directed

Supply and fixing sub main wiring with 2 runs of 2.5 sqmm single core, multi-stranded PVC insulated, FRLS unsheathed cable 1100 Volts grade with copper conductor drawn through and including concealed non metalic PVC conduit, medium grade, ISI marked, suitable size with conduit fittings and accessories concealed in wall/ceiling/floor including 1 run of 2.5 Sqmm multistranded PVC insulated FRLS, copper conductor cable as earth continuity conductor and connecting to common earth dolly incl taking down old unsv one from site complete all as directed NOTE: Two runs of 2.5 sqmm copper cable and one run of 2.5 sqmm copper cable alongwith non metallic PVC conduit/conduit accessories will be measured as one unit length (For Offrs Servant qtrs)

Supply, install & testing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, single phase, 1200 RPM, Copper winding of sweep 250mm complete fixed/grouted to wall with suitable bolts, nuts etc., and connecting up with & including 3 core flexible copper conductor cable (1.0 mm² size/core) from ceiling rose to exhaust fan and writing MES No. including cutting hole suitable for fixing exhaust fan complete all as specified and directed Make: Havells or equivalent in Orient/Crompton

Supply & Fixing for Wall mounted, indoor, HELIOS Mirror Light LED with aluminium die cast, suitable for and including 10 watt 6000K, WH LED light, prewired incl connecting up complete all as specified and directed.

Supply & Fixing for Dusk & dawn roadway luminaries 45 Watt, 230 V AC, 5700K outdoor type with epoxy black powder coated sheet of make: Havells or equivalent make of Philips/Crompton, high pressure die-cast aluminum hosing and heat resistant complete with impact and corrosion resistant including thermal management in multiple optics, PF>95%, THD<10%, Lumen>4500 lm with IP 65/66 protection complete incl connecting wire with flexible PVC insulated copper cables from ceiling rose to fitting including driver, lamp bracket made of 32mm bore galvanised iron light grade pipe made to shape having overall length not exceeding 1.5 mtr, through mild steel clamp of 25mm width and four Nos. nuts, bolts & washers of 12mm dia, 100mm long fixed to wall with all other fittings complete and testing all as specified and directed.

Supply & Fixing for storage electric heater (Geyser), flexible mounting of capacity 25 ltrs, single phase, 240 volts, AC, white colour, with incoloy heating element and PUF insulation, ISI marked BEE 5 star rated complete with high precision & externally adustable capillary thermostat for temp regulation, backup safety overheating capillary therrmal cut out at 95ºC, temperature display, etc., including provn of suitable holding clamp, MS bolts, grouted to wall and connecting up including 3 core sheathed multi-stranded flexible copper conductor cable connected with 15/16 Amp plug top and provn of water connections with new PVC steel braided inlet/outlet connection pipe 15mm dia, 450mm long with two numbers union, NRV of suitable size, check/end nuts with washers, 15mm dia 100mm long nipples (02 Nos) for hot water and cold water connections and making good to the disturbed surface in cement morter as required and testing complete all as directed NOTE: Cost of flexible copper cable of 3 core, PVC steel braided inlet/outlet pipe of 15mm dia, 450mm long with brass union, NRV, check/end nuts, nipples, MS bolts, etc., and minor parts, if any, other than those are not specified in the schedule and required for smooth functioning of geyser will be deemed to be included in the quoted rate

M/s. M Company (BID ID -3203731)

S S CONSTRUCTION COMPANY (BID ID -3203751)

ESS KAY BUILDER (BID ID -3197311)