SPECIAL REPAIR TO BLDG NO P 18A (COOK HOUSE) AT INF BN NO 1 BRICHGUNJ MIL STN, PORT BLAIR

Amount

Dismantling plain or corrugated steel sheeting, any thickness including Nainital or similar pattern roof coverings complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in roof coverings/cladding to wall, etc, fixed with & including self tapping screws on angle frame complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in roof coverings/cladding to wall, etc, fixed with & including self tapping screws on angle frame complete all as specified and directed.

M & L for water proofing treatment with the following specifications including taking down existing roof treatment of any description and cleaning with water and scrubbing and disposing off the rubbish outside the premises, complete all as specified and as per manufacturers instructions:- (i) Rendering 10mm thick in CM 1:4 on concrete surfaces mixed with water proofing compouund @ 3% by weitht of cement as leveling course (ii) Apply a coat of hot blown bitumen 85/25 @ 1.20 kg/sqm over a coat of bituminous primer @ 0.3 ltr per sqm. (iii) Laying APP membrane (STP Aquashield or equivalent) weighing not less than 3.5 Kg/sqm, reinforced with polyster non woven fabric (weighing not less than 150 gms/sqm) with 100mm over laps both longitudinally and transversally and overlaps shall be sealed by torch, membrane shall be taken to the parapet through fillet and shall be tucked in inside after a height of 300 mm. (iv) Apply one coat of hot blown bitumen 85/25 @ 1.2 kg/sqm over the membrane. Note :- Water proofing compound shall be measured and paid separately as supply only.

Dismantling, floor, hearth or wall tiling including cement mortar bedding complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

All as per item No 7.00 here in before, but on vertical surfaces except screed bed incl 10mm thick CM 1:3 as in baking coat of dado/skirting complete all as specified and directed.

M&L for Coloured Glazed ceramic concept tiles (approved design/pattern with high lighter tiles) of size not less than 300mm x 450mm x 7mm thick, in vertical surfaces such as dados, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 10mm thick rendering in CM 1:3 complete all as specified and directed.

M&L for 20 mm thick granite (of any type) work (area not less than 1.5 sqm each granite slab, table rubbed and polished) in floors and like; in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including 20mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for Chequered cement concrete tiles with grey cement and no pigments 200mm x 200mm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with & including 20mm thick screed bed in CM 1:4 complete all as specified and directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, ceilings, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for Rendering 10mm thick in cement mortar 1: 6 on faces of brick work or concrete surfaces, finished fair, even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in two coats on faces of brick work or concrete surfaces; first coat (rendering coat) of 10 mm thick in cement mortar 1: 6 and second coat (finishing coat) of 5 mm thick in cement mortar 1: 4 mixed with water proofing compound (water proofing compound to be measured separately as supply only) and finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound

M&L for rendering 5mm thick in cement mortar 1: 3 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M & L for two coats of OBD over a coat of primer on newly plastered surfaces of walls including nesessary preparation of surfaces complete all as specified and directed.

M&L for two coats of weather coat(Exterior) all guard emulsion, any colour/tined to new wall surfaces over a coat of primer including necessary preparation of wall surface complete all as specified and directed.

M & L for two coats of OBD over a coat of primer on newly plastered surfaces of ceiling including nesessary preparation of surfaces complete all as specified and directed.

M & L for preparing old decorated surfaces of ceiling and applying two coats of OBD over a coat of primer complete all as specified and directed.

M & L for two coats of OBD over a coat of primer on old plastered surfaces of walls including nesessary preparation of surfaces complete all as specified and directed. .

M&L for two coats of weather coat(Exterior) all guard emulsion, any colour/tined over a coat of primer.including complete removal of old treated wall surfaces complete all as specified and directed.

M&L for preparation of old steel surface of any description over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

S & F Aluminium anodised (minimum anodisation is 15 microns) Door / window / Ventilator/partition frames and shutters (02 Nos glazed & gauzed), side hung type, without sash bars, standard aluminium grills, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, locking arrangement etc,including taking down aluminium door/window/Ventilator/partition frames and shutters all as specified and as directed by Engineer-in-charge.(Aluminium section shall be of make Jindal/Hindalco/ Indalco). (Note:- Weight of various Aluminium sections shall only be considered for measurement for payment. However cost of rubber packing given in the item shall be deemed to be included in the rate quoted. Glass panels,prelaminated particle boards, aluminium wire cloth as applicable will be measured and paid separately as supplied only & Item Such as hinges shall be considered under supply and fix items).

Supply only 4 mm thick ACP board (Aluminium Composite Panel ) fixed to aluminium frames complete all as specified and as directed.

Supply only 4mm thick sheet glass ordinary quality and glazing with rubber packing around the glass, in squares n. exc 0.5 Sqm in each pane complete all as specified and as directed.

Supply only 4mm thick figured glass ordinary quality and glazing with rubber packing around the glass, in squares n. exc 0.5 Sqm in each pane complete all as specified and as directed.

Supply only aluminium alloy wire mesh 0.45mm nominal dia of wire and average width of apeture 1.4mm fixed with aluminium wire staples etc.complete all as specified and as directed.

Supply and fix in repair aluminium alloy wire mesh 0.45mm nominal dia of wire and average width of apeture 1.4mm fixed with aluminium wire staples etc.complete all as specified and as directed.

S&F solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing in SSR complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC `C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing in SSR complete all as specified and directed.

S&F in repairs 75mm Size Butt hinges type C-21 , extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed complete all as specified and directed.

S&F in repairs 100mm Size Butt hinges type B-21 , extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed complete all as specified and directed.

S & F in repairs 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S & F in repairs 100 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F in repairs Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S & F in repairs 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F in repairs100 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

Supply & Fix in repairs 140mm long door stopper of aluminium alloy body and tounge, anodised with hard drawn steel spring fixed in floor complete all as specified and as directed.

Taking up or down 25mm dia bore steel tubing galvanised and connections complete all as specified and directed.

Taking up or down 15mm dia bore steel tubing galvanised and connections complete all as specified and directed.

Supply and laying 20mm external dia UPVC pipes SDR11 including Plain UPVC fittings SDR11 mean fittings which do not have any metal component and is jointed with CPVC solvent cement only (Elbow, Tee, Socket, Reducer, Bushing, Step over bends, End cap, End plugs, etc) & Special fittings include CPVC Brass fittings (Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor, etc), Unions, Ball valves, Flange and tank adaptor as on walls/ceiling/floors complete all as specified and directed.

Supply and laying 25mm external dia UPVC pipes SDR11 including Plain UPVC fittings SDR11 mean fittings which do not have any metal component and is jointed with CPVC solvent cement only (Elbow, Tee, Socket, Reducer, Bushing, Step over bends, End cap, End plugs, etc) & Special fittings include CPVC Brass fittings (Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor, etc), Unions, Ball valves, Flange and tank adaptor as on walls/ceiling/floors complete all as specified and directed.

S&F in repair 20mm dia Gun metal globe or gate valve with iron wheel head, screwed both end for iron pipe complete all as specified and directed.

S&F in repair for 25mm dia ball brass valves, high pressure, with polythen float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repair PVC flushing cistern 10 litres capacity syphonic action type, low level, white with inlet, ball valve, float, handle and flush pipe, etc complete all as specified and directed.

S&F in repairs Brass Chromium plated shower rose 125mm size, with swivel joint, fixing to steel pipe or union, complete all as specified and as directed.

Supply and fix in repairs Bib tap, cast copper alloy chromium plated,15 mm dia with fancy type screwed down for iron pipes or brass ferule etc, complete all as specified and directed.

S & F in repairs angular stop cock, cast copper alloy chromium plated, 15 mm dia screwed down high pressure, screwed both ends for iron pipe or for unions complete all as specified and directed.

All as per Item No. 50 but fancy type, chromium plated with long shank and cup (concealed type) screwed both ends for iron pipe or for unions complete all as specified and as directed.

S & F in repairs fancy type, Pillar taps , cast copper alloy , with capstan heads , chromium plated , screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe of bore 15 mm and fixed in repairs, complete all as specified and as directed.

S & F in repairs sink with drainage board, made up of stainless steel, 1mm thick for kitchen or laboratory with plug washers and waste fittings, including bedding in cement mortar 1:3 into dwarf wall or cantilever brackets and connecting union to pipe, over all size 915mm x 460mm, bowl size 410 x 330 x 160mm etc, complete all as specified and as directed.

S&F in repair vitreous china wash hand basin white flat back size 630x450mm incl brackets, PTMT coupling, 32 mm GI pipe waste pipe complete all as specified and as directed.

S&F in repairs brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

S&F in repairs stainless steel gratings 125mm dia, complete all as specified and as directed.

S&F PVC connection both end brass union 15 mm dia & check nuts of length 450 mm long.

S & F in repairs vitreous china squatting pan, Orissa pattern size 630X450 mm white with integral foot rest (excluding flushing cistern) including 'P' or 'S' trap etc complete all as directed.

S & F rotational moulded polythelene water storage tanks ISI marked (cylindrical vertical with closed top) of 500 Ltrs capacity with tank cover (top), hoisted and fixed in position, including taking down existing with all connections complete all as specified and as directed by Engineer -in-Charge.

S & F rotational moulded polythelene water storage tanks ISI marked (cylindrical vertical with closed top) of 1000 Ltrs capacity with tank cover (top), hoisted and fixed in position, including taking down existing with all connections complete all as specified and as directed.

Dismantling of CI drain pipes,50-100 mm dia jointed in cement mortar including all fittings joints etc complete all as specified and directed.

M&L for PVC (SWR) pipes 110mm bore double socketed in any length with rubber ring joints, fixed to wall incl testing of pipe etc complete all as specified and directed.

M&L for PVC (SWR) pipes 75mm bore double socketed in any length with rubber ring joints, fixed to wall incl testing of pipe etc complete all as specified and directed.

M&L for PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75mm outer dia, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)

Supply and fix PVC (SWR) bends 110mm bore with oval access doors all as specified and directed.

Supply and fix PVC (SWR) bends 75mm bore with oval access doors all as specified and directed.

Supply and fix PVC (SWR) junction single, (Single T) 110mm bore, equal or unequal with oval access doors all as specified and directed.

Supply and fix PVC (SWR) junction single, (Single T) 75mm bore, equal or unequal with oval access doors all as specified and directed.

Supply and fix PVC (SWR) branch piece, single (single Y) equal or unequal 110mm bore, equal or unequal with oval access doors all as specified and directed.

Supply and fix PVC (SWR) branch piece, single (single Y) equal or unequal 75mm bore, equal or unequal with oval access doors all as specified and directed.

Demolition of unreinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) all as specified and directed.

M&L for PCC 1:3:6, type C2, (Using 40 mm graded stone aggregate), 100mm thick as in plinth protection/Sub base flooring, finishing surface fair and even, in panels & filling joints with mortar, etc., complete all as specified and as directed.

M&L for removing loose and broken concrete by chiselling /picking etc upto a depth of 10 to 30 mm from floor/roof slab/chajjas and similar structural members cleaning the dismantled portion with wire brushes etc to remove dust, dirt and other foreign particles including necessary scaffolding etc and removal of debris to a distance not exceeding 50m, complete all as specified and as directed.

M&L for application of high build polymer modified cement mortar (1:2.5) mixed with 3 kg SBR per bag of cement in ceiling surfaces 10 to 30mm thick in two layers surfaces over a coat of bonding agent Nito Bond SBR (1 Ltr SBR + 1 Ltr) water + 3 kg cement), complete all as specified and as directed.

M&L for removing loose and broken concrete by chiselling, /picking etc upto a depth of 80 to 100mm from column/ beams and similar structural members cleaning the dismantled portion with wire brushes etc to remove dust, dirt and other foreign particles including necessary scaffolding etc and removal of debris to a distance not exceeding 50m, complete all as specified and as directed.

M&L for applying one coat of anti corrossive primer @ 0.25 Lit/Sqm for the steel area to exposed old and new reinforcement to the full circumfrance and length of bars to form unbroken 40 Micron thick film complete all as specified and as directed.

M&L for applying one coat epoxy bonding agent @ 2.6 sqm/lit or as per manufacture’s instruction to old concrete surfaces of columns, beams and similar structural members complete all as specified and as directed. Make: fosroc/ bostik/ STP

M&L for non shrink, cementitous micro concrete mixed with 12.5 graded stone aggregate using Renderoc RG or equivalent by weight (18 Kg Aggregate : 25 Kg Renderoc RG) respectively (as per manufacturer’s instruction) laid in average thickness 80 to 100 mm in surface, including necessary watertight form work complete all as specified and directed. Make: fosroc/ bostik/ STP

M&L for spraying curing compound as per manufactures instruction on freshly cast concrete surfaces complete all as specified and directed. Make : Concure WB white of Fosroc or equivaent in bostik /STP

S&F Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F Mild steel TMT bars 6 to 8mm dia as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Demolition of precast concrete block walling, built in cement mortar including all quoins, arches, pillars, etc complete all as specified and directed.

M&L for precast cement concrete solid block masonry with solid blocks using PCC 1:2:4, type C1 (using 20mm graded stone aggregate), exc. 10cm in width, set in CM 1:6 complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed

M & L for roughning of surfaces of old concrete floor by picking sweeping clean and washing down with water to remove dust etc complete all as specified and as directed

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specified complete all as specified and as directed.(plinthprotection)

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets Including frame of any description and any thickness, fixed in any position complete all as specified and as directed

S&F steel work in tubular for columns,roof truss,purlins,rafters and battens etc incl special shaped washer etc complete using ERW or induction but welded tube conforming to IS : 1161-1979 Gde St-240 completely providing in any curvature and as of any shape etc complete all as specified and as directed

M&L for Plates (Plain or Chequered) channels, square or notched (Ordinary and counter sunk) forming holes, without any attachment of Fe 290 (Gde E-165) complete all as specified and as directed

M/L 25mm thk PCC 1:2:4 type B-0 using 12.5 mm graded agg as in flooring finished fair and even without using extra cement complete all as specified and as directed

M&L for 75mm thick Cement concrete in C1 type (1:3:6) using 20mm graded stone aggregate as in plinth protection and finished even and smooth with using extra cement complete all as specified and as directed.

Supply only 12 mm thick pre-laminated particle board, exterior grade, pre-laminated on both side with decorative choice lamination fixed with aluminium beeding as in door panel complete all as specified and as directed

S&F Aluminium Die cast Body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified and as directed

M& L for Finishing walls with Acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) etc complete all as specified and as directed .(Make Apex Ultima)

M&L for preparation of new steel surface exc 10cm width or girth and applying Two coat of red oxide primer and two coat of synthetic enamel paint glossy complete all as specified and as directed

Material and labour for false ceiling with aluminum grid work (Size of grid 600x600 mm) with 35 x 25 x 1.5 mm main tee and 25 x 25 x 1.4 mm cross tee and wall angle and suspended with 2mm dia GI wire hooked to roof with needful adjustement bolts at an interval of 1.20 m centre to centre staggered and board with Eco board decorative type size 600 x 600 x 4 mm thick finished with two coats of oil bound distemper over a coat of primer on exposed surfaces complete all as specified and as directed.

M&L for providing 100mm thick cement concrete 1:4:8 type D2 using 40mm graded stonne aggregate as in sub base of flooring complete all as specified and directed.

Taking up or down, 20mm dia bore, GI tubing, medium grade, including cleaning for refixing or removing from site, complete all as specified and as directed

S&F in repair stop valves 15mm dia bore of cast copper alloy, screwed down, high pressure, with fancy type, chromium plated, screw both ends for union and fixed complete all as specified and as directed

S&F in repairs two way bib cock, brass CP mixture for mixing hot & cold water complete of Make Jaquar Cat Part No ARI 39041 complete all as specified and as directed

S&F as in repair Hand Shower (Health Faucet) 1 Meter Long Flexible Tube & Hook complete all as specified and as directed. (Make:- Jaquar Cat No ALD CHR -585)

S&F in Repair wash hand Basin of size 375x475x130mm including all connecting fittings and brackets etc of Jaquar Cat Part No JDS WHT-25907, complete all as specified and as directed

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), white including connection to trap and to flushing pipe, anti syphonge pipe etc, including making good the floor complete all as specified and as directed.

S & F in repairs 15mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, minimum weight 142 gms, complete all as specified and as directed.

S&F in repairs 15mm dia nipple of PTMT, suitable for HDPE water tank, min weight 38 gms, complete all as specified and as directed.

S&F in repairs shower arm 190mm long light body with wall flange and exclusive shower single flow with revolving ball joint as per cat. No.477 / 493 of make Jaquar complete all as specified and as directed.

S&F 100 mm CI Floor trap with grating incl jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and as directed

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in floor complete all as specified and as directed

S&F PVC (SWR) Gully 125/110 mm,seting and incl joining with solvent cement complete all as specified and as directed

S&F PVC (SWR) cowls 75mm dia complete all as specified and as directed

S&F PVC (SWR) cowls 110mm dia complete all as specified and as directed

Taking down carefully aluminium point wiring (light, fan, socket or power) DBs complete offering credit, making good disturbed surfaces of walls, floors, etc, complete all as specified and directed.

M&L Point wiring complete with 1.5 sqmm single core FRLS PVC insulated and unsheathed cable 1100 volts grade with multistranded copper conductor drawn through and including PVC casing and caping and all accessories fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm copper cable green in colour as earth continuity conductor and connected to common earth dolly, including fabricated steel terminal box made out of 1.60mm thick MS sheet concealed in walls, with 3mm thick laminated sheet top cover for housing the switches, socket outlets,fan regulators etc., all as specified and as directed for the following:- (a) One light point controlled by one switch

(b) One exhaust fan point controlled by one switch

(c) One fan point controlled by one switch and one regulator

(d) One 3 pin switch socket outlet point 5 amps on independent board

All as per item No 115 above but for 3 pin 15 Amps switch socket combination on independent board with 4 sq mm copper cable and provision of 4 sq mm FRLS PVC insulated stranded copper conductor cable for earth continuity conductor connected to common earth dolly connecting upto fittings complete all as specified and as directed.

Supply and fix switch piano flush button single pole oneway 5 amp complete all as specified and as directed.

Supply and fix switch socket combination 3 & 2 pin (multi pin) 5 amp flush type complete all as specified and as directed.

Supply and fix switch socket outlet multipurpose 3 pin 15 and 5 amp controlled by one switch, flush type complete all as specified and as directed.

Supply and fix ceiling rose surface bakelite 65x50mm 3 terminal complete all as specified and as directed.

Supply and fix fan speed regulator, electronic suitable socket type for single phase AC, 240 volts, 50 Hz,100 watts, complete all as specified and as directed.

Taking down old unserviceable ceiling fan 1200 mm sweep by disconnecting the electric power supply, unscrewing the bolts and nuts, removing the blades and bearing including scrapping of old paint and applying two coats of synthetic enamelled white paint over a coat of red oxide primer complete and refixing back at site with new clamps, nuts, washers, safety wire of size not less than 1.00mm & bolts including cotter pin for complete all as specified and as directed.

Taking down old unserviceable exhaust fan 300 mm sweep by disconnecting the electric power supply, unscrewing the bolts and nuts, removing the blades and transporting to workshop to undertake repairs for rewinding of burnt out winding using suitable gauge copper wire, replalcement of worn out capacitor 4.0 mfd - 01 No and bearing including scrapping of old paint and applying two coats of synthetic enamelled grey paint over a coat of red oxide primer complete and refixing back at site complete all as specified and as directed.

Supply and fix in repair metal enclosure distribution board SPN, 8 way 240 volts, with 200 amps rated bus bar, double door suitable for mounting MCBs including taking down old MCB/DB complete all as specified and directed. Note-: Incoming & outgoing connections from the DB shall be provided with proper lugs/ thimbles etc

Supply and fix in repair sheet metal enclosure Loadline distribution vertical DB, MCCB as incomer 4 ways 415 volts, with 200 amps rated bus bar double door suitable for mounting MCCB 100 A TPN as incomer and MCBs as outgoing, Triple pole as incoming complete all as specified and directed including taking down old MCB DBs complete.Thye Rate shall be included the incomer MCCB TPN of 100 Amps complete all as specified and directed. Note-: Incoming & outgoing connections from the DB shall be provided with proper lugs/ thimbles etc

Supply and fix in repair MCB single pole 240 volts, 6 to 32 amps "C" series complete all as specified and as directed.

Supply and fix single pole and netural 240 Volts 32 amps complete all as specified and as directed.

Supply and fixing energy efficient aluminium housing LED Smart bright batten 22 /20 Watt mounted batten fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core shethed cable from fitting to ceiling rose complete all as specified and directed.

Supply and fixing energy efficient aluminium housing LED Smart bright batten 10 Watt mounted batten fitting 2 ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core shethed cable from fitting to ceiling rose complete all as specified and directed.

S&F 25 W New genration energy saving & envoirmental friendly long life versatile pressure dia cast aluminium IP65 road way luminaire with high power LEDs as light and electronic driver complete with necessary brackets (made out of 25 mm bore GI light grade pipe approx. 0.6 M long) nuts, bolts etc to be fixed as on walls complete all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant complete with IP 65/66 protection complete all as specified and directed.

M & L in repairs for sub main wiring complete with two runs of 6 Sqmm FRLS single core PVC insulated unsheathed single core cable 1100 volts grade, multistranded with copper conductor (ISI Marked) drawn through and including PVC Casing and caping and all accessories fixed to wall/ roofs/ floors etc with one run of 6 sqmm FRLS single core multistranded copper conductor as earth continuity conductor, including dismantling unserviceable sub main wiring including accessories,complete all as specified and as directed by Engineer-in-Charge. Note : (1) Two runs of cable one run of casing caping & one run of earth continuity conductor shall be measured as one running metre.

M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less thab 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part - I

supply & Lay XLPE insulated, heavy duty 1100 volt grade electric armoured LT UG cable with aluminium conductor of size 25 Sqmm 3.5 Core in trenches/along the wall/including making all connections, saddles, spacers including scaffolding if any required for saddling the cable in walls of building of height up to 25 meter, complete with aluminium lugs as required at site complete all as specified and directed.

Supply & lay cable protection pipe of HDPE double wall corrugated (DWC) incl couplers,bends etc of size 50 mm OD and ID 38mm confirming to IS 14930 -II and ISI Marked complete all as specified and directed.

Supply, lay, test and commissioning under ground XLPE insulated and PVC sheathed, armoured heavy duty under ground cable, suitable for earthed system, laying in trenches/duct sleeving through pipe in duct, ISI marked with aluminium stranded conductor 1100 volt grade of cross section area 2 Core 10 sq mm complete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50m and depositing where directed. at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Supply and fix 25 mm bore GI tubing medium grade laid in trenches / floor or fixed to wall in any length with screwed and socket joints together with all galvanised GI fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc and pressure testing, washing out complete all as specified and directed

Supply and fix 40 mm bore GI tubing medium grade laid in trenches / floor or fixed to wall in any length with screwed and socket joints together with all galvanised GI fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc and pressure testing, washing out complete all as specified and directed

Supply and fix 25 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, complete all as specified and as directed

M&L for cutting existing 40mm GI line and making branch connection of 25 mm dia GI line including fittings required for connection complete all as specified and directed

Supply and fix 25 mm bore Gun Metal gate valve with iron wheel head ISI Marked screwed both ends suitable for GI tubing complete all as specifed and directed

Supply and fix 40 mm bore Gun Metal gate valve with iron wheel head ISI Marked screwed both ends suitable for GI tubing complete all as specifed and directed

DEEPAK AGENCIES

M/s Kamal Electrical

P Babu

M/s Saina Enterprises

Nirman Construction Company

Bismi Builders & Enterprises

M/s Harjas Construction & Waterproofing Co