Special repair to various residential buildings under Division No. III (SH- Replacement of roofing, repair of door, window, P/F PGI sheet Ceiling, railing, floor tile, PVC flooring, and other miscellaneous work at Bhajji House building at Kainthu Shi

Amount

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within all leads and lifts including carriage of materials: G.S. Sheet.

Dismantling wood work in frames, trusses, purlins and rafters up to 10metres span and 5metres height including stacking the material within all leads and lifts including carriage of materials:Of sectional area 40square entimetres and above. including carriage of materials within all leads and lifts.

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within all leads and lifts including carriage of materials.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within all leads and lifts including carriage of materials:Of area 3 sq. metres and below.

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within all leads and lifts including carriage of materials.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material wwithin all leads and lifts including carriage of materials:For thickness of tiles 10mm to 25mm

Demolishing cement concrete manually/ by mechanical means including disposal of material within all leads and lifts including carriage of materials as per direction of Engineer - in - charge Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix).

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50m :Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia within all leads and lifts including carriage of materials.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within all leads and lifts including carriage of materials.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand) : 6 graded stone aggregate 20 mm nominal size) complete including carriage of materials within all leads and lifts as per direction of Engineer - in - charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand) : 4 graded stone aggregate 20 mm nominal size) complete including carriage of materials within all leads and lifts as per direction of Engineer - in - charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in :Cement mortar 1:4 (1 cement :4 coarse sand) complete including carriage of materials within all leads and lifts as per direction of Engineer - in - charge.

Providing wood work in trusses, purlins, rafters, posts, post plates, wall plates and the like wrought framed, hoisted and fixed in position. complete including carriage of materials within all leads and lifts as per direction of Engineer - in - charge.:-2nd class deodar wood.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) complete including carriage of materials within all leads and lifts as per direction of Engineer - in - charge:- Sal wood.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-incharge Second class teak wood. 35 mm thick shutters. including carriage of materials within all leads and lifts.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :including carriage of materials within all leads and lifts.35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size complete including carriage of materials within all leads and lifts as per direction of Engineer - in - charge:-Second class deodar wood.

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc.complete. including carriage of materials within all leads and lifts.Kiln seasoned and chemically treated Rai Wood complete including carriage of materials within all leads and lifts as per direction of Engineer - in - charge.

Providing eaves board 200mmx25mm thick including fixing in position in 2nd class deodar wood including carrage of material within all leads and lifts as per direction of Engineer-in-charge.

Providing weather board 100mm x 25mm thick including fixing in position 2nd class deodar wood including carriage of materials within all leads and lifts.

Providing and fixing 0.63mm thick PGI sheet ceiling/lining of approved quality with butt jointing and wood screws (frame work and cover fillets to be measured and paid for separately) including carriage of materials within all leads and lifts.

Providing and fixing hard wood plain square edged cover fillets (beading) 40mm x 12mm section with wood screws in ceiling and lining including mitring at junctions including carriage of materials in all leads and lifts.

Providing and fixing plain square edged cover fillets (beading) 60mm x 12mm section with wood screws in ceiling and lining including mitring at junctions. 1st class kail wood.

Providing and fixing 250mmx16 mm size aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete including carriage of materials within all leads and lifts.

Providing and fixing 250mm x10 mm aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials within all leads and lifts.

Providing and fixing 150mm x10 mm aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials within all leads and lifts.

Providing and fixing 125mm size aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials within all leads and lifts.

Providing and fixing 100mm size aluminium handles, ISI marked, anodised (anodic coating not less than grade AC10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials within all leads and lifts.

Providing 40mm x 3mm flat iron hold fast 40cm. Long including fixing to frame with 10mm diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm. 1:3:6 ( 1 cement : 3 sand: 6 graded stone aggregate 20mm nominal size). including carriage of materials within all leads and lifts.

Providing and fixing water proof shuttering ply of standard quality ISI mark and approved shade and colour in panelling & wall linning i/c mitring at junctions, butt jointing and nails complete (Frame work for base to be measured & paid for separately) 12mm thick including carriage of materials within all leads and lifts.

1.5 mm thick pvc/rubber tiles flooring (L.G. Make) plain, coloured. corbed or mosaic or mattled finish, laid with approved adhesive on sub floor damp proofing treetment(to be measured separately)for payment including carriage of materials within all leads and lifts.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete including carriage of materials within all leads and lifts.Size of Tile 600x600 mm.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete comlete including carriage of materials within all leads and lifts.Size of Tile 500x500 mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge complete including carriage of materials within all leads and lifts.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works including carriage of materials within all leads and lifts.

Centering and shuttering including strutting, propping etc. and removal of form for :Suspended floors, roofs, landings, balconies and access platform complete including carriage of materials within all leads and lifts.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, alconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size) including carriage of materials within all leads and lifts.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level including carriage of materials within all leads and lifts.:- Mild steel and Medium Tensile steel bars.

Dubbing out an old irregular walls average 10mm thick with Cement mortar 1:6 (1 Cement : 6 Sand) including carriage of materials in all leads and lifts.

15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 fine sand) including carriage of materials in all leads and lifts.

Providing and fixing murga jali of wire mesh on wall before plastering with nails etc. complete or as per the direction of engineer-in-charge including carriage of materials within all leads and lifts.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.60 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required including carriage of materials within all leads and lifts.

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gm/m². including carriage of materials within all leads and lifts.

Providing valleys of 90 cm wide overall in plain G.S. sheet fixed with polymer coated J, or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 1.60 mm thick with zinc coating not less than 350 gm/m². including carriage of materials within all leads and lifts.

Providing and fixing of 40 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts, G.l. limpet and bitumen washer complete, bent to shape and fixed in wall with cement mortar 1:3 (1 cement : 3 coarse sand) 1.00 mm thick with zinc coating not less than 275 gm/m². including carriage of materials within all leads and lifts.

Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works including carriage of materials within all leads and lifts.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre. including carriage of materials within all leads and lifts.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10sqm over an under coat of primer applied @ 0.80ltr/ 10sqm of approved brand and manufacture including carriage of materials within all leads and lifts.

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture including carriage of materials within all leads and lifts.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade. One or more coats on old work. including carriage of materials within all leads and lifts.

Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (One or more coat applied @ 0.90 ltr/10 sqm). including carriage of materials within all leads and lifts.

Providing and fixing high pressure PVC (Finolex) type-A spigot and socket, waste and ventilating pipes including collar and clamps ISI marked including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts:-150 mm dia. including carriage of materials within all leads and lifts.

Providing and fixing high pressure PVC (Finolex) type-A spigot and socket, waste and ventilating pipes including collar and clamps ISI marked including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts:-110 mm dia. including carriage of materials within all leads and lifts.

Providing and fixing PVC (Finolex) door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc.complete. including carriage of materials within all leads and lifts. 110 mm nominal size.

Providing and fixing PVC (Finolex) door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc.complete. including carriage of materials within all leads and lifts. 150 mm nominal size.

Providing and fixing PVC (finolex) plain single equal branch with oval access door, insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete including carriage of materials within all leads an lifts- (i) 110 mm nominal size.

Providing and fixing PVC (finolex) collars ISI marked including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts.150 mm dia.

Providing and fixing PVC (finolex) collars ISI marked including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts.110mm dia.

Providing and fixing PVC (finolex ) Plain bends of required degree (any radius) including fixing with approved adhesive etc.complete, including carriage of materials within all leads and lifts:-110mm nominal size.

Providing and fixing PVC (finolex ) Plain bends of required degree (any radius) including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts:-150mm nominal size.

Providing and fixing 15 mm dia nominal bore G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. complete including carriage of materials within all leads and lifts:-Internal work - Exposed on wall.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 complete including carriage of materials within all leads and lifts.

Extra for depth for manholes Size 90x80 cm 150 cm depth With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including carriage of materials within all leads and lifts.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore. including carriage of materials within all leads and lifts. Make Seiko or equivalents.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore. including carriage of materials within all leads and lifts. Make Seiko or equivalents.

Providing and fixing kitchen sink mixture including carriage of materials within all leads and lifts:- Make Seiko or equivalents.

Providing and fixing C.P. Wall mixture including carriage of materials within all leads and lifts. including carriage of materials within all leads and lifts. Make Seiko or equivalents.

Providing and fixing 100 mm dia chromium plated grating of superior quality for floor, gully or nahani trap including carriage of materials within all leads and lifts

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. W.C. pan with ISI marked white solid plastic seat and lid.,Make Cera or Hindware complete including carriage of materials within all leads and lifts.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps. White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps. Make Cera or Hindware complete including carriage of materials within all leads and lifts.

Providing & fixing 32mm dia, PVC waste pipe for wash basin or sink including carriage of materials within all leads and lifts. including carriage of materials within all leads and lifts.

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length. 15 mm nominal bore. including carriage of materials within all leads and lifts.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40mm, including painting of fittings and brackets, cutting and making good the walls wherever required complete including carriage of materials within all leads and lifts :610x460 mm bowl depth 200mm.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.including carriage of materials within all leads and lifts.

Providing and fixing 600mm x 120mm x 5mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40mm long screws, rawl plugs etc., complete. including carriage of materials within all leads and lifts.

Providing and fixing looking mirror of size 600mm x 450mm with plastic frame (superior quality) including backing support and fixing with screws etc at site as directed by Engineer-in-charge including carriage of materials within all leads and lifts.

Providing and fixing single hole basin mixer with with top / bottom swinging spout SEIKO Delux or its equivalent of approved quality including carriage of materials within all leads and lifts.

Pawn Kr