JOINT FILLING OF RUNWAY, TAXI TRACK, CLEARANCE OF GRASS / FOLIAGE FROM RUN AND TAXI TRACK SHOULDERS AND OTHER B/R WORKS IN AOR OF ARMY AVN SQN AREA UNDER GE NASIK ROAD.

Amount

Raking out existing construction joints/dummy joints 10mm wide X 25mm deep in concrete pavements, cleaning surfaces and sweeping to make the surface free from dust/dirt with air compressor/blower and reoving debris to a distance exceeding 200m form edge of pavement for disposal in low lying areas.

Raking out existing expansion joints 20mm wide X 25mm deep in concrete pavements, cleaning surfaces and sweeping to make the surface free from dust/dirt with air compressor/blower and reoving debris to a distance exceeding 200m form edge of pavement for disposal in low lying areas.

Filling construction joints/ dummy joints 10mm wide X 25mm deep in concrete pavements with sealing compound Grade ‘B’ after applying primer to the sides of jopints as per manufacturer's instructions.

Filling expansion joints 20mm wide X 25mm deep in concrete pavements with sealing compound Grade ‘B’ after applying primer to the sides of jopints as per manufacturer's instructions.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings.

Dismantling wrought iron or mild steel work of any description such as purlins ofor roof and window guard bars.

Supply and fixing steel work in tubular or rectangular hollow section in rafters, purlins etc. and connected works complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240

S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F 2mm thick Fibre glass reinforced translucent reinforced corrugated sheeting with two corrugations side lap fixed with coach screw and washers in roof wall etc complete all as specified and as directed.

Preperation of new untreated steel or iron surfaces of any description over 10cm girth or width, not otherwise described and two coats of synthetic enemel paint over a coat of red oxide, zinc chrome primer.

Taking down aluminium door shutters of any description.

Taking down aluminium window shutters of any description.

Taking down aluminium door and window frame of any description.

M&L for Aluminium (minimum 50 micron powder coated) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

M&L for Aluminium (minimum 50 micron powder coated) door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

M&L for Aluminium (minimum 50 micron powder coated) window and ventilator shutters, side hung/sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.) hinges type B-21, 100mm long (2 Nos.), suitable handle (1 No.), rollers, grip etc. complete all as specified

M&L for 5.5mm thick sheet glass plain or tinted, ordinary quality, fixed in aluminium doors and windows.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple or fixed in alumionium frames.

S&F Floor door closer hydraulically regulated, universal type (cast iron body) suitable for aluminium door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed

Preparation of old or previously treated steel or iron surfaces of any description over 10cm width or girth and two coats of aluminium paint over a coat of red oxide primer.

Demolition of cement concrete in ground floors and pavings n exc 15cm thickness (below or above ground level).

M&L for 75 mm thick cement concrete 1:4:8 type D2 (40 mm graded aggregate) in sub floor.

M&L for 100mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate)

M&L for rough shahabad stone 25mm to 30mm thick in flooring /plinth set and jointed in neat cement slurry and pointed in cm 1:4 including 20mm thick screed bed or bedding in cm 1:6 complete all as specified and directed.

M&L for 30 cm x 30 cm x 20 to 25 mm thick chequered tiles of rubber moulded with grey cement and pigment are polished, decorative set and pointed in neat cement sluurry in floors etc including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for Machine pressed precast conctete interlocking paver block with grey cement and pigment with rubber moulded glossy finished surface, any shape and size confirming to IS 15658-2006 of 60 mm thickness M-30 grade laid over and including 30 mm thick stone dust cushion.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for Vitrified Ceramic tiles (Double charged) 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick cement mortar screed bed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match.

M&L for Vitrified Ceramic tiles (Superior quality) 10 mm thick (square/ rectangular) polished in skirting etc. cut out of tiles of area not exceeding 0.36 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick cement mortar rendering in cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match.

M&L for Non Skid ceramic tiles coloured 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 sqm but not exc 0.11 sqm , in floors etc. including 15mmm thick cement mortar screed bed in cement mortar 1:6,set and jointed in neat cement slurry and pointed in white or coloured cement to match

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick including 15mm thick cement mortar rendering in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or colour cement to match

M&L for Demolition of Brickwork or stone/boulder masonry, built in cement mortar.

M&L for Brickwork with flyash bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L for Rendering 15mm thick in cement mortar 1:4 on faces of brick work finished fair and even.

M&L for preparation of newly plastered surfaces and applying two coat of cement base paint on wall complete all as specified and directed.

Dismantling barbed wire fixed to any type of standard rails straining bolts (each line wire to be measured).

Dismantling chain link fencing any type .

Dismantling MS Angle/RCC posts or struts any section, embedded in concrete, brick work, masonry,Mild Steel etc. including taking out embedded portion and making good disturbed ground.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth round, in layers not exceeding 25 cm in soft/loose soil.

S&F Posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire.

Supply only chain link MS galvanisd fencing, any size or type.

S&F 4mm dia plain mild steel wire, galvanised class 3 in fencing including straining and fixing to concrete or steel posts and/or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. as directed (each line of wire to be measured).

S&F flat iron fillets (for securing wire mesh, chain link fencing etc.) including all necessary drilling, bolting or riveting etc., MS stiffener bars for chain link fencing and similar work.

S&F mild steel screw bolts (machine made) diameter of neck 5 to 10mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n exc 10cm.

Preparing new untreated steel or iron surfaces any description exc 10cm width or girth and two coats of aluminium paint over and including a coat of red oxide zinc chrome primer.

Preparing Old painted steel or iron surfaces any description exc 10cm width or girth and two coats of aluminium paint over and including a coat of red oxide zinc chrome primer.

Preparing new untreated steel or iron surfaces any description n.exc 10cm in width or girth and two coats of aluminium paint over and including a coat of red oxide zinc chrome primer.

S & F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundation filling, mass concrete and sub base of floor complete all as specified and directed.

Dismantling Wall and ceiling boards (fibre,pulp, insulation, etc.) orinsulation boards/slabs/blankets, any thickness, including cover fillets

S & F wall panelling 'Anutone-ACT KLH' Vinyl finish,Bevel edge of size 600 x 600 x 25 mm thick with glass fiber core,in rectangular/Square grid of size 600mm(H) x 600mm(W) fixed on wall using galvanised steel 'Strul Z-Bar' or 'Impale clip' fixed to the wall in grid pattern all as per manufacturer instruction. NRC is upto 1.0 and fire class 'A'. Note:Contractor quotated rate shall be deemed to be inclusive of all minor/major items of exectution to complete the work as per manufacturer instructions.

S & F False Ceiling 'Anutone-subtex Nubby' ceiling panel of size 595 x 595 x 20 mm thick, texture finish concealed edge with glass fibre core fixed to T-grid ceiling frame work using galvanised steel 'Skelet Trelis' T 24 concell' system consisting of main tee MT 24 W 36 at 600 c/c and cross tee CT 24 W 12 at 600 c/c,wall angle WA 24 W 30 around wall and spacer bar WA 24 W 30 at 600 c/c all as per manufacturer's instructions. Thickness of main/cross tee will be 0.3mm and that of wall angle/spacer 0.4mm. NRC is upto 0.90 and Fire class is I & P. Note:Contractor quotated rate shall be deemed to be inclusive of all minor/major items of exectution to complete the work as per manufacturer instructions.

Cutting/clearance of grass,vegitataion/foliage from runway and taxi track shoulders and deposited 500m to 1000m from runway and taxitrack

Taking down carefully existing bituminous membrane/tarfelt treatment any description and cleaning and making good damaged surface of roof ,parapet,facia etc in cement mortar 1:3/PCC 1:2:4 as directed by engr-in-charge where ever require.quotated rate shall be deemed to be inclusive of complete removal of swollen plaster and concrete wherever directed by engr-in-charge and removing rubbish out of defence land. Note: work is to be executed at any height and situation.

Demolition of concrete (unreinforced) of any description and in any position not otherwise secifically provided for.

M&L for Providing cement concrete type B0 1:2:4(12.5mm graded aggregate) in roof kerbs or mud stops,ridge, rounded or chamfered on edges.

M&L for rendering 15 mm thick(minimum) in CM 1:4 with intergral waterproofing compound (200 ml per bag of cement used) on roof surfaces,parapets,facias etc .curing as per standard eng practices. Note: waterproofing compound shall be measured and paid separately.

Supplying only integral water proofing compound ISI marked complete all as specified and as directed.

M&L for Applying evenly a coat of hot blown bitumen 85/25 over roof surface,facia,parapet etc at the rate of 1.2 kg per sqm for fixing app membrane etc including cleaning surfaces.make same as for APP membrane.

M&L for Waterproofing on roof including flashing and junctions of parapet,kerb, wall etc.as under :- (a) Laying a layer of APP based polymeric membrane,3 mm thick(minimum),weighing not less than 3.60 kg/Sqm prefabricated fire layer waterproofing membrane reinforced with polyester non woven fabric(weighing not less than 160 gms/sqm) shall be applied over compatible primer at 0.40 litre/Sqm of density at 25 degree Centigrade 0.87-0.89 Kg /Litre and viscosity 70-160cps or cold sticker, application of APP modified membrance shall be by torch application. The overlaps shall be minimum 150mm on the transverse direction and 100 mm on the longitudinal direction. (b) APP membrance,Primer and bitumastic aluminium paint and bitumen shall be of same brand. (c) For vertical surfaces i.e. parapets,wall etc. app membrane shall be tucked into groove and sealed with silicon sealant i.e. "Dowsil 789 weatherproofing silicon sealant" using gun. (d) Bitumen and aluminium paint shall be paid separately.

M&L for applying two coats of solar reflective bitumastic aluminium paint at the rate 0.15kg/sqm per two coats over exposed app membrane surfaces(old/new) including preparation of surfaces to the entire satisfaction of ground executives. Note: Make same as for app membrane.

Disconnecting existing tanks exc 250 n exc 500, setting aside (or lowering if required) cleaning and removing all scale dirt,etc from the mouth of circulating pipes etc and hoisting if required,reconnecting and re-fixing in position. Note: work is to be executed at any height and situation.

Disconnecting existing tanks exc 500 n exc 1000, setting aside (or lowering if required) cleaning and removing all scale dirt,etc from the mouth of circulating pipes etc and hoisting if required,reconnecting and re-fixing in position. Note: work is to be executed at any height and situation.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 500 litre capacity, hoisted and fixed in position all as specified.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 litre capacity, hoisted and fixed in position all as specified.

S&F ball valves, 20mm bore high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 210gms) fixed in repairs.

Fixing only in repair ball valves any bore or size.

Taking up or down 15mm tubes galvanized iron and connections & removing/ shifting to site/store incl cleaning for relaying/refixing where directed. Note :- 1. Rates quoted are inclusive of taking out bib taps,PVC float valves and fitting as per site condition.

Refixing 15mm tubes galvanized iron as directed incl renewal of threading/tread cutting at ends of GI pipes fixed to walls or laid in floor and jointing incl S/F new fitting such as socket, bends, elbows, union etc all as specified and directed (Concealed ).

S&F for 15mm tubes medium grade galvanized with all fitting fixed to walls, ceiling and laid in floor (Concealed ) .

Taking up or down steel tubing and connections 20mm bore.

Refixing old steel tubing and connections 20mm bore in new or old position (Walls, ceiling, floors, etc.)(Concealed ).

S&F 20mm bore galvanised steel water tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors (Concealed ).

S&F in repairs vetreous china squatting Pan (orissa pattern), size 580 x 440, white with integral foot rest (excluding flushing cistern and flush pipe) including provn of lime concrete bedding and vitreous china P or S trape complete all as specified and directed.

S&F in repairs Cascade type EWC, coloured with integral flush tank, floor mounted with P/S trap and directed, cistern shell, cistern lid, dual flush ultra solid seat cover, dual flush fitting internal ie cascade dual flush set complete cascade range C-0216/7 or equivalent approved make all as specified and directed.

S&F in repairs vetreous china wash down water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) complete all as specified

S&F in repairs vitreous china wash basin Flat back 550x400mm excluding taps, chain and plug and porceilein stopper but incl brackets cutting for and pinning in ends of brackets or errecting stand, CP waste coupling of suitable size with long shank and bracket grouted in CM 1:2 in wall completed all as specified and directed.

S&F in repairs plastic seat cover white closed pattern with flat bottom and cover with mild steel chromium plated or alluminium hinging device complete all as specified and directed.

S&F in repairs PVC valveless, syphonic action type 10 ltr capacity flushing cistern, low level, white or coloured, with inlet, ball valve,float and handle including brackets.

S&F in repairs chromium Plated cast copper alloy pillar tap with capston heads fancy type fixed to iron pipes 15mm dia..

S&F in repairs bib tap 15mm bore Chromium plated fancy type with crutch or butterfly handle fixed to iron pipes.

S & F in repair Stop valves, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

M&L for One coat of exetior emulsion paint (apex/weathercoat) over one coat of acrylic wheather coat primer on walls and ceiling plastered or unplastered surfaces including preparing by brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots; removing vegetation, nails,making good holes by filling CM 1:4, cracks etc.by filling with putty height upto four storied buildings.

M&L for Two coat of exetior emulsion paint (apex/weathercoat) over one coat of acrylic wheather coat primer on walls and ceiling plastered or unplastered surfaces including preparing by brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots; removing vegetation, nails,making good holes by filling CM 1:4, cracks etc.by filling with putty height upto four storied buildings.

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS. 37,050.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

Alpha Construction

Abhiraj Enterprises

Bidder Name

Alpha Construction

UNITED ENTERPRISES

Abhiraj Enterprises