6 laning of Pani-Jal section of NH-I from Km.96.000 to Km.387.100 in the State of HR and PB to be executed asBOT (Toll) on DBFO Pattern under NHDP Phase-V Balance BC Overlay Works between km. 96.000 and km.387.100 (Balance stretches in HR and PB

FINANCIAL BID FORM

To From: (Name of Firm)

Regional Office, Chandigarh National Highways Authority of India, NHAI Building, Sector - 30B, Chandigarh (UT) - 160030, (Near Sector – 29-30 Traffic Light, Opposite 30 C Market) Tel: 0172 - 2586818

Name of work: Six laning of Panipat-Jalandhar section of NH-I from Km. 96.000 to Km. 387.100 in the State of Haryana and Punjab to be executed as BOT (Toll) on DBFO Pattern under NHDP Phase-V: Balance BC Overlay Works between km. 96.000 and km. 387.100 (Balance stretches in Haryana and Punjab sections Risk & Cost).

Reference letter No.

1. Having examined the site of works and Bid Documents, comprising Instructions to Bidders, Scope of works, Conditions of Contract, Technical Specifications, Bill of Quantities and schedules for the execution of the above named works, we, the undersigned offer to execute and complete such works and remedy any defects therein in conformity with the said bid documents for the sum as offered in the online financial bid form or such other sum as may be ascertained in accordance with the said Bid documents.

2. We undertake, if our Bid is accepted, to commence the work within fifteen (15) days of receipt of the order to commence, and to complete and deliver the sections and whole of the works comprised in the Contract within the period stated in the bid hereto.

3. If our Bid is accepted, we will furnish Performance Security (ies) in the form of a Bank Guarantee to be jointly and severally bound on us, in accordance with the Conditions of Contract.

4. We agree to abide by this Bid for the period of One Hundred & Twenty (120) days from the last date fixed for Bid Submission and it shall remain binding upon us and may be accepted at any time before the expiry of that period.

5. We confirm our agreement to treat the Bid documents and other records connected with the works as secret and confidential documents and shall not communicate information contained therein to any person other than the person authorized by the Employer or use such information in any manner prejudicial to the safety and integrity of the works.

6. Unless and until an agreement is prepared and executed, this Bid, together with your written acceptance thereof, shall constitute a binding Contract between us, but without prejudice to your right to withdraw such acceptance without assigning any reasons thereof.

7. We understand that you are not bound to accept the lowest or any bid you may receive.

Yours faithfully

**Name and Designation of the authorised signatory

** Certified copy of Power of Attorney/Authorization for signature shall be furnished by the bidder.

Bill of Quantities (BOQ)

Name of work: Six laning of Panipat-Jalandhar section of NH-I from Km. 96.000 to Km. 387.100 in the State of Haryana and Punjab to be executed as BOT (Toll) on DBFO Pattern under NHDP Phase-V: Balance BC Overlay Works between km. 96.000 and km. 387.100 (Balance stretches in Haryana and Punjab sections Risk & Cost).

Sr No. Description Unit Quantity Rate per unit Amount (In Rs)

1 Milling on Existing Bituminous Surface Dismantling of existing damaged bitumen surface by cold milling machine up to 50 mm depth and hualing the milled material upto 10 km and stacking at nearest reclying plant site as per direction of Engineer-in-charge and disposal of unserviceable material within all leads and lifts. Sqm 142500 28.86

2 Tack Coat @ 0.25kg per sqm Providing and applying tack coat with bitumen emulsion RS using emulsion pressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous surface/granular surface treated wit prime coat after cleaning the surface complete as per technical clause 503 of MORT&H specifications. Sqm 285000 13.75

3 Providing and laying bituminous concrete 40mm thick with batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder VG-40 @ 5.4%, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction complete as per technical clause 507 of MORT&H specifications (SOR -24.23 a) cum 5700 10543.98

4 Providing and laying dense graded bituminous macadam 50mm with batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder VG-40 @ 4.5%, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction complete as per technical clause 505 of MORT&H specifications. Cum 7125 9415.46

5 Providing and marking of hot applied Thermoplastic compound 2.5 mm thick including reflectorising glass beads at 250 gms/sqm. Area , thichkness of 2.5 mm is exclusive of surface applied glass beads as per IRC 35. The finished surface to be levelled, uniform and free from streaks and holes complete in all respect. The job includes marking of centre line, shoulder line, edge line, Zebra crossing marking, arrows and dashes at the junctions as per Technical Specifications clause no. 803.4 complete in all respect as per approval of Engineer-In-Charge. Sqm 4560 550.60

6 Moulded Shank Road Stud:Supplying and fixing of single mould twin shank reflective road studs made out of poly carbonate/ABS moulded body and reflective panels with micro prismatic lens or Glass Beeds capable of providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values shall be as given in the detailed specifications and the product shall conform to ASTM D4280. The raised pavement marker shall also meet all the testing conditions of ASTM D4280 and fixed to the road surface using the adhesive. Two cylindrical Polymer Shanks of not less than 20 mm diameter and not less than 30 mm length shall be molded in the RPM body. The marker shall support a load of 13635 Kg tested in accordance with ASTM D4280. The marker shall withstand flexural strength of 909 kgf force in accordance with ASTM D4280. Marker lenses shall be moulded of Polycarbonate or methyl methecrylate conforming to ASTM D788. The supplier shall provide a 2 years warranty for satisfactory field performance as per clause 804.7.3 of MORT&H 5th revision specifications. No. 2536 217.60

7 Painting two or more coats, excluding priming coat, with synthetic enamel paint in all shades on woodwork, metallic surfaces, or plastered and concrete surfaces to provide an even and uniform shade. Sqm 5700 79.08

8 Recovery for the milled material (40% BC) shall be made at the rate of 20% of the quoted rate for the item of BC. The material obtained from milling of the existing bituminous layer has been calculated as per theoretical calculations, and the agency shall take away this material at the fixed rate mentioned above. If the actual quantity of material retrieved after dismantling is found to be less, no claim of the agency shall be entertained, and full recovery based on the quoted rates shall be made. The dismantled material may be used in any item of the work after necessary modification to meet the requirements of MORTH Specification Clause 519 and with the approval of the employer; however, if it cannot be used in the work, the agency may take it away. Notwithstanding the use or non-use of the material in the work, recovery shall be made for the quantity and at the rates specified herein. The bidder/agency is advised to visit the site before quoting rates and to assess the likely extent of retrieved material. Cum 2850 -2079.14

Total Estimated Cost

Bidder to quote single rate as tender premium % above or discount below the total estimated cost mentioned above. In Words In Figures

I/We hereby agree to execute the above work on the tender premium or discount quoted here on the total estimated cost mentioned above. I/we understand that filling of both cells meant for premium or discount at a time will render my/our bid as non responsive. Premium

Bid price in Rs.

Note: 1. For bituminous items, if bitumen requirement as per job mix formula is more than the minimum requirement as per clause, no extra payment shall be made. Extra bitumen requirement shall be considered incidental to work. 2. The material required for construction work shall be as per MoRT&H specifications for road and bridge works (Fifth Revision/latest edition) and fulfills NHAI Policy guidelines no. NHAI/TIC/PQ/2012-13/205 dated 19.10.2022 and approved by the Engineer incharge. 3. All duties, taxes (excluding GST), royalties and other levies payable by the Contractor under the Contract, or for any other cause, shall be included in the rates, prices, and total Bid price submitted by the Bidder. Nothing extra shall be payable on this account except GST which shall be payable at the applicable rates.

CSR Item No. Description of Item Unit Qty./Premium Rate

24.7 a Construction of granular sub-base by providing close graded material grading -I, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per technical clause 401 of MORT&H specifications CUM 1194

CARRIAGE FROM PATHANKOT FROM PATHANKOT TO site TOTAL LEAD 80 KM [ Chapter 5.2(i)] CUM 425.58000000000004

Plant to Site 6 km CUM 200.67

Rate Of GSB per Cum 0.0

Total Rate Of GSB per CUM 1820.25

CSR Item No. Description of Item Unit Qty./Premium Rate

24.13 Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant, carriage from mix plant to site of work, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density complete as per technical clause 406 of MORT&H specifications CUM 1579.11

CARRIAGE FROM PATHANKOT FROM PATHANKOT TO site TOTAL LEAD 80 KM [ Chapter 5.2(i)] CUM 425.58000000000004

Plant to Site 6 km CUM 200.67

Basic Rate for WMM per Cum 2205.36

TOTAL RATE of WMM per Cum 2205.36

CSR Item No. Description of Item Unit Qty./Premium Rate

24.19 Dense Graded Bituminous Macadam 80mm to 100mm thickness (Grading I)

(a) Providing and laying dense graded bituminous macadam 80mm to 100mm thick with batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder VG-40 @ 4%, Dense Graded Bituminous Macadam 80mm to 100mm thickness (Grading I) bituminous binder VG-40 @ 4%, carriage of mixed material to site of work, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction complete as per technical clause 507 of MORT&H specifications CUM 6164.68 6164.68

CARRIAGE FROM PATHANKOT FROM PATHANKOT TO site TOTAL LEAD 80KM [ Chapter 5.2(i)] CUM 425.58000000000004

CARRIAGE FROM Bathinda REFINARY TO plant TOTAL Round Trip 550 KM[ Chapter 5.2(iii)] ton 92.62

Carriage for DBM from DBM plant to site 6 km Cum 200.67

Difference of price of VG 40 and VG 30 (Rs 1500 per MT) as CSR rate is inclusive of VG 30 ton 138

Total Rate for Dense Graded Bituminous Macadam 0.0

Total Rate for Dense Graded Bituminous Macadam 7021.55

CSR Item No. Description of Item Unit Qty./Premium Rate

24.15 Prime Coat @ 0.85kg per sqm

Providing and applying primer coat with bitumen emulsion SS on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.85kg/sqm complete as per technical clause 502 of MORT&H specifications Sq. m 32.11 32.11

Basic Rate for Prime coat per Sqm 0.9

Total Rate for Prime coat per Sqm 32.11

CSR Item No. Description of Item Unit Qty./Premium Rate

24.23 Bituminous concrete 30mm to 45 mm (Grading II)

(a) Providing and laying bituminous concrete 30mm to 45 mm thick with Continuous type hot mix plant using crushed aggregates of specified grading ,premixed with bituminous binder CRMB 60 / PMB @ 5.4%, laying with a Paver Finisher Mechanical to the required grade, level and alignment, rolling with smooth wheeled ,vibratory and tandemr ollers to achieve the desired compaction complete as per technical clause 507 of MORT&H specifications CUM 7409.77 7409.77

CARRIAGE FROM PATHANKOT FROM PATHANKOT TO site TOTAL LEAD 80KM [ Chapter 5.2(i)] CUM 425.58000000000004

CARRIAGE FROM Bathinda REFINARY TO plant TOTAL Round Trip 550 KM[ Chapter 5.2(iii)] ton 92.62

Carriage for BC from BC plant to site 6 km Cum 200.67

Difference of price of CRM 60 and VG 30 (Rs 3000 per MT) as CSR rate is inclusive of VG 30 ton 372.6

Total Rate for Dense Graded Bituminous Macadam 0.9

Total Rate for Dense Graded Bituminous Macadam 8501.24