Additional works at Forest Resource Management Centre ICT Narwal, Jammu by way of Providing and Fixing of Aluminium partitions, Wire gauge shutters, Re-construction/ Repair of compound wall and other allied works.

Amount

Earth work in excavation by Mechanical means in foundation trenches, drains, pipes and cables etc. (not exceeding 1.5mtr in width or 10 sqm on plan including dressing of sides and ramming of bottoms, lift upto 1.5mtr including getting out excavated soil and disposal of surplus soil as directed, within a lead of 50 mtr. All kinds of soils

Providing and laying in position cement concrete of specified grade excluding the cost of centring and Shuttering 1:5:10 (1 cement: 4 coarse sand :8 graded brick aggregate 40 mm nominal size):- CRUSHED including all carriages.

Providing and laying in position cement concrete of specified grade in retaining wall, return wall, wall (any thikness) in 1:3:6 mix ( 1 cement:3 coarse sand: 6 graded stone aggregate 40mm nominal size including curing complete excluding cost of centring & shuttering including all carriages.

Centring and shuttering including strutting, propping etc. and removal of form work for:-

Foundations: footings, bases of columns etc. for mass concrete.

Brick work with common burnt clay F.P.S.(non-modualar) bricks of class designation 75 in foundation and plinth including curing in:- Cement mortar 1:6 ( 1 cement : 6 coarse sand); (Including cost / Carriage of material by Mechanical transport) above plinth level upto floor five level

15mm Cement plaster on the rough side of single or half brick walls of mix: 1 : 6 ( 1 cement : 6 fine sand) on interior walls ,all complete including making of groves and scaffolding, etc. at all floor levels complete (Including cost / Carriage of material by Mechanical transport)

Finhishing wall with waterproofing cement paint of required shade on new work (two or more coat applied @ 3.84 Kg/10 sqm)

Providing and laying of vitrified floor tiles (double charged) in different sizes (thickness to be specified by the manufacturer) (Anti-skid) with water absorption less than 0.08% and conforming to lS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete SOMANY/ KAJARIA or equivalent only make; at all floor levels complete:- size of tile 60cmx60cm (Including cost / Carriage of material by Mechanical transport)

Cleaning of underground septic Tank and Sever line, Manholse including flushing of sewer line from one manhole to another manhole including dechocking of sewer line whereever required as per site complete. Two nos. Septic Tank of size 15'x20' & one number sump Tank.

Labour engaged for dismentling of old brick work, damage Tile flooring including clearing of site by way of removing rubbish & other unserviceable material

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber I neoprene .. gasket felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I panelling, C.P. brass I stainless steel screws, all complete as per architectural drawings and the directions of Engineer-inCharge (glazing, panelling and dash fasteners to be paid for separately.)For fixed portion Polyester powder coated aluminium (minimum thickness of polyester powder coated 50 microns) for partitions walls.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber I neoprene .. gasket felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I panelling, C.P. brass I stainless steel screws, all complete as per architectural drawings and the directions of Engineer-inCharge (glazing, panelling and dash fasteners to be paid for separately.)For shutters of doors, windows & ventilators including providing and fixing hinges I pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber I neoprene gasket required (Fittings shall be paid for separately.) Powder coated aluminium (minimum thickness of powder coated 50 microns) Door Window shutters.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber I neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item.) With floating glass panes of 5.00 mm thickness (weight not less than 12.50 kg / sqm)

Providing and fixing pre laminated particle boardflat pressed three layer or graded wooded particle board ( conforming to IS : 12823 Grade -I type -II) in panelling fixed in aluminium doors, windows shutters and partition frames with C.P brass stainless steel screws etsc. complete ads per architectural drwinghs and directions of engineer - in- charge pre laminated particle board with decorative lamination on both sides.

Providing and fixing aluminium tower bolt ISI marked anodized (anodic coating not less then GRADE-AC 10 as per IS :1868)transparent or yed to required colour or shade with necessary screws etc. complete 250mmx10 size ( with standard specifications.)

Providing & fixing brass 100mm mortice latch & lock with 6 levers without pair of handles (Best maker) for Aluminium doors with necessary screws & fittings including cutting & making good.

Filling of gap in between aluminium frame & adjacent RCC/Brick wall by providing weather Silicon sealent over backer rod upto 5mm of depth & 5mm width al complete.

Providing and fixing aluminium handles ISI marked anodized (anodic coating not less then GRADE-AC as per IS :1868)transparent or yed to required colour or shade with necessary screws etc. complete 125mm size ( with standard specifications.)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, having brand logo em,possed on the body/plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot" and single piece M.S. sheet outer box with slide plate etc. complet~ as per the direction of Engineer-in charge. With Stainless Steel cover plate minimum 1.25 mm thickness

Providing and fixing 35 mm thick glazed shutters for Windows, Doors, ventilators and clerestory windows using 10 kg/sqm (4mm thick) float glass panes with lSI marked Stainless steel Butt hinges bright finished (heavy weight) of required size with necessary screws of Second Class Deodar Wood.

Providing and fixing 35 mm thick wire guage shutters for Windows, Doors, using stainless steel grade 304 wire guage with wire of 0.5mm instead of galvanized M.S. wire with 0.63mm of aperture of 1.4mm in both direction of second Class Deodar Wood.

Applying priming coat with ready mix pink or grey primer of approved brand and manufacture on wood work (hard wood & soft wood).

Painting with ready mixed synthetic enamel paint of approved brand and manufacture Asian / Nerolac / Berger / Dulux paints only in all shades to give an even shade New steel/wood work complete at all levels (two or more coats).

Removing dry or oil bound distemper, Water proofing Cement paint by Scrapping and Sand papering and preparing the surface smooth including necessary repairs to scratches etc complete

Providing & applying white cement based putty of average thickness 2mm of approved brand & manufacturer over the plastered wall surface to prepare the surface even & smooth in patches.

Wall painting with plasting emulsion paint of approved brand and manufacture on old work to give even shade (one or more coat) of required shade.

Renewing Glass panes with putty & nails wherever necessary including taking out putty of damaged glass panes & fixing of new float glass of required thickness 5mm & density (not less than 12.50 Kg/Sqm) of required shade.

Renewing Glass panes with wooden fillets wherever necessary with float glass of required thickness 4mm & density (not less than 10.00 Kg/Sqm) of required shade.

Refixing of existing Stain less Steel railling wherever required with all fittings including labour complete.

Labour engaged for cleaning of Tile/Granite flooring with Liquid Detergent/hard stain Acid cleaner including Mopping of floor complete:- a) Labour

Water profing of expansion joints as per standard specification.

Supplying of various items required for cleaning of tile/Granite flooring

Liquid Detergent

Sponge/ Cloth Wiper

Harpic Toilet Cleaner

Hard stain Acid cleaner

Note:- The bidder shall quote the rate inclusive of all types of carriages (H.L & M.T) all types of Scaffolding required there in inclusive all taxes applicable.

harbans Lal

Ashok Kumar Gupta