SPECIAL REPAIR TO BLDG NO. T 81, T33, T29, T30 DINING HALL OF 749 I TPT PL ASC, SPECIAL REPAIR TO ROOF OF BUILDING NO. P10 ALL KOTE OF 111 INF BN A KUMAON AND P85/3, P92/03, P100/03, P100/06, P102/06, P699 601 IN NAR BAHADUR SINGH COLONY AT N

Amount

Taking down cement or cement lime plaster, any description on brick or stone wall etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for brick work with sub class B; bricks ,straight or curve on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

M&L for preparation of new plastered surface of wall with scrapping machine tools / electric hand grinder with wire brush, sand paper and applying two coats of cement base paint over & including one coat of primer complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of white wash with paint sprayer machine complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof coverings including ridges complete all as specified and directed.

M & L Prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed..

M&L for steel work in tubular trusses, purlins, rafter, tubular column, where connected common rafter and running rails fixed with angle cleat or other connection plates including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed.

S& F for in repair of to 4mm thick non asbestos fiber cement building boards fixed or laid/ inserted to timber/GI/aluminum framework with screws over anodized aluminums snap grid frame work for false ceiling with Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified all as specified

S&F rolled mild steel conforming to Gde Fe 290 (Gde E-165) (Plain or chequred) , joist, channel, angle or tee sections, fixed independently, without connecting plates, etc complete all as specified and directed.

M&L for MS screw bolts 11 to 15 mm dia (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and hexagonal or square nut exceeding 15 cm and not exceeding 22.5 cm long complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Demolition of brickwork of any description and in any position built in cement or cement lime mortar including all coin, arches, pillars complete all as specified and directed.

Demolition of cement concrete including floor tiles or stone in any description and any position etc removal from site and complete all as specified and directed

Dismantling plain or corrugated steel sheeting any gauge thickness including nanital or similar pattern roof covering complete all as specified and directed.

Dismantling wrought iron or mild steel work, rolling shutters of any description not otherwise provided for complete all as specified and directed.

S&F in repair powder coated GI ceiling suspension system false ceiling grid of 600 mm x 600 mm size and 0.30 mm thick (m.S. galvanised with main Tee, cross tee and wall angle grid hanging with 4 mm dia GI wire and roof fasteners or butterfly clips etc complete all as specified & directed.

S&F hangers 6 mm dia G.I. ( upto 1200 mm length ) adjustable level fixed to roof slab by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60 mm long and expansions hold fasteners 12.5 mm dia 40 mm long complete all as specified & directed.

S&F in repair 4 mm thick non asbestos fiber cement building board of 600x600 mm in size (HPSC E-classic) decorative finish fixed to aluminum /CGI frame work with hold down clips in false ceiling complete all as specified and as directed.

Complete removal of existing treatment on wall of old decorated surfaces by scrapping tools/electric hand grinder and applying 1 mm thick birla white based wall care putty, after dry the layer of putty, apply two coats of oil bound distemper white or tinted with paint sprayer machine over a coat of primer complete all as specified and directed.

Complete removal of existing treatment on wall of old decorated surfaces by scrapping tools/electric hand grinder and applying 1 mm thick birla white based wall care putty, after dry the layer of putty, apply two coats of cement based paint white or tinted with paint sprayer machine over a coat of primer complete all as specified and directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding and removing rubbish off the premises complete all as specified and directed.

M&L for vitrified pavement outdoor tiles of 300mm X 300mm X 9-10 mm thick coloured for floor /pavement etc and jointed in solvent and pointed in coloured cement to match the tiles including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as directed.

M&L for 75 mm thick cement concrete 1:3:6 type C2 using 40 mm graded stone aggregate in plinth protection finished even and fair including necessary form work and cutting of joints and fixing of PVC or glass strips not more than 3 M or every turning point etc complete all as specified & directed.

Demolition of plain cement concrete in any position including tar felt & cement mortar bedding etc from roof or sunken complete all as specified and directed.

Dismantling of brick tiles or terracing tiles, single layer on roofs complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and removing debris complete all as specified and directed

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces with WPC complete all as specified and directed (Note : WPC to be measured and paid separately under appropriate item)

Demolition of mud in roof, any thickness including plastering and leaping ( where full thickness recovered or only a part there of disposal off rubbish upto a distance n.exc 500m, where directed complete all as specified and directed. Note:- Removal of demolished material shall be measured and paid separately under respective item.

M&L for plain cement concrete 1:2:4 type B-0 12.5mm graded stone aggregate as in roof padding, roof kerbs, benching on roof slab and other similar works laid as per slop required finished even and fair complete all as specified and directed.

M&L for 10mm thick plaster in CM 1:3, mixed with liquid water proofing compound over concrete surface of roof /chajja on cleaning of surface complete all as specified and directed. (Note : WPC to be measured and paid separately under appropriate item)

Cleaning the dust, dirt and any other foreign material from roof surface and applying a coat of bituminous primer @ 0.40 ltr / Sqm uniformly and primer shall be allowed to dry over night as conforming to IS 3384-1986 complete all as specified and directed.

M&L for Laying of minimum 3mm thick APP membrane of (reinforced with non-woven fabric polyester type wt not less than 150 gms/Sqm) & minimum weighing 3kg/Sqm shall be done using butane torch maintaining 100mm side overlap and 150mm end overlap, sealing all overlaps and bonded to the surface by fusing and bonding torch on method complete all as specified and directed. Note: All water proofing work shall be done as per manufacturer instruction and under supervision of manufacturer technical representative.

Supply only Liquid water proofing compound (ISI marked) complete all as specified and directed.

M&L for 40mm thick brick tiles laid over and including 20mm thick screed bed in CM 1:4 mixed with polymer based liquid water proofing additive @ 5 % by weight of cement or as per manufacturer's instruction and the joints of tiles shall be filled with CM 1:3 mixed with crude oil as per SSR-2009 (Part-I) on roof area and proper curing with water by ponding complete all as specified and directed.

All as per item No 37 but except tiles complete all as specified and directed. Note:- Tile obtained from dismantling shall be used.

Disconnecting existing water tanks exceeding 250 & not exceeding 500 ltrs setting aside (or lowering if required) and hoisting, reconnecting and re-fixing in same position after cleaning complete all as specified and directed.

S&F in repair rotational moulded polyethylene water storage tank of capacity 500 ltr (Cylindrical/vertical with closed top) double layer construction, ISI marked hoisted & fixed in position including dismantling of old tank and removing from site complete all as specified and directed.

S&F in repair ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed 20mm bore minimum weight 210 gms complete all as specified and directed.

Taking up or down 15 mm bore GI steel tubing and connections on (walls, ceiling, floors, etc.) including cleaning complete all as specified and as directed

Refixing old 15 mm bore GI steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed

S&F 15 mm bore GI steel tubing "medium grade" with all fittings and fixed to wall, floor and ceiling etc complete all as specified.

Taking up or down 20 mm bore GI steel tubing and connections on (walls, ceiling, floors, etc.) including cleaning complete all as specified and as directed

Refixing old 20 mm bore GI steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed

S&F 20 mm bore GI steel tubing "medium grade" with all fittings and fixed to wall, floor and ceiling etc complete all as specified.

S&F in repair 20mm bore dia stop valve cast copper alloy screwed down , high pressure with crutch or butter fly handle, screwed both ends for pipe or for unions and fixed complete all as specified and directed.

S & F in repairs 110 mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to walls or floor or in trenches complete all as specified and directed.

S & F in repair 110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S & F in repair 110 mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed.

M&L for Reinforced cement concrete 1:2:4 using 20 mm graded stone aggregate as in chajja and the like with necessary form work complete all as specified and directed. Note:- Reinforcement & formwork to be measured & paid separately under respective item.

Form work to chajjas and similar items including edges for rough finished flat surfaces of concrete complete all as specified and directed.

M & L for Mild steel TMT bars 5 mm to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping as in stirrups for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

Complete removal of mud phuska from roofs of any thickness and removing the waste material from site to a distance exc. 250m but not exc. 500m and deposited where directed including cleaning of surface complete all as specified and directed.

M&L in replacement for concealed submain wiring using FRLSH PVC insulated, unsheathed stranded copper conductor cable two single core of size 6.0 Sqmm of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories along with one run of PVC insulated unsheathed stranded copper conductor of size 6.0 Sqmm as earth continuity conductor complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

M & L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick directly buried in ground (earth pit not less than 2.25 m deep below ground level) with top edge of earth plate not less than 1.5m below the ground level connected to GI earth wire 4mm dia by means of bolts nuts check nuts and washers of galvanised iron at 2 points & GI pipe 15 mm bore light grade for protection of earthing wire PCC chamber 1:3:6 (type C-1) using 20mm graded stone aggregate, watering pipe 20mm bore light grade, funnel with wire mesh, 50 mm thick cover of RCC 1:2:4 type B-1 using 20mm graded stone aggregate reinforced with 8 mm MS bars at 150 mm centre to centre both ways and charcoal dust and common salt all as shown in electrical plate No. 3 of MES SSR part-I and including excavation & earth work & connecting the earthing point/equipment and testing complete all specified and directed.

S & F VTPN DB 4 way DPX³ 100A MCCB Double door DB's as per IEC 61439-3, suitable for flush mounting and surface mounting with 250 Amp copper busbar for each phase with 2 Neutral bar, 2 earth bar and cable ties for cable management, fully insulated busbar & shrouded neutral bars, improved pan assembly for ease of installation, prefitted masking sheet, reversible door for IP 43 & IP 54 DB's with provision for DPX³ 100 MCCB as incomer and SP/TP MCB's as outgoing with metal door complete all as specified and directed.

S & F in repair MCCB 100 Amps, 415 Volts, 4 Pole, breaking capacity 16 KA, ISI marked, adjustable type complete all as specified & directed.

S&F in replacement sheet metal enclosure for MCB's 240 volt 8 way single pole and neutral conforming to IS- 13032, IS- 8623, BS- 5484 with 200 amps rated busbar, double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

S&F in replacement sheet metal enclosure for MCB's 240 volt 4 way single pole and neutral conforming to IS- 13032, IS- 8623, BS- 5484 with 200 amps rated busbar, double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

S&F MCB single pole, 6 to 32 amps rating, 240 volts, 'C' curve, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F MCB SPN 40/63 Amps 'C' curve breaking capacity 10 KA of rating & making connection complete all as specified & directed.

Taking down carefully point wiring of any type complete for light, fan socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets, regulators, wooden batten, surface conduit/casing caping/conceal etc. removing materials including accessories for taking credit and making good disturbed surface to match the existing complete all as specified & directed.

M&L for point wiring with FRLS PVC insulated unsheathed stranded copper conductor cable 1.5 Sqmm (nominal area) 1100 volts grade, along with one single run of same size and type of copper wire as continuous earth wire to common earth dolly drawn in and including non metallic PVC rigid, medium grade concealed conduit with all fixing accessories of 20mm dia, using new MS sunk terminal boxes of thickness not less 1.2mm, new 3mm thick laminated sheet cover with brass screw and cup washers with all accessories and making good to disturbed conceal surfaces complete all as specified and directed. Note:(a) Colour code of wire shall be strictly followed , Red for Phase , Black for neutral and green for earth wire (b) The unit rate quoted is deemed to be inclusive of cost of cutting chases in wall for providing concealed conduit and making good to match with existing finish/surface.

One light/fan/bell point controlled by one switch

One point for socket outlet 5 amps on independent board but not below the switch board in same vertical plane.

One point for socket outlet 5 amp same board.

One bell/ buzzer point controlled by one push button on the same board with other switches or independent

All as per srl item No. 65 above but for one 3 pin socket outlet 15 amps, independent, with cables 4 sqmm size on independent board 4 Sqmm earth wire complete all as specified and directed.

S&F in repair ceiling rose surface type bakelite 65 X 50 mm three terminal complete all as specified and directed.

S&F call bell, ding dong type, AC, 230 V, single pole complete all as specified & directed.

S&F modular Switch piano single pole one way 6 amps complete all as specified & directed.

S&F modular Socket out let 2 in one, 5/3 pin 6 Amp flush type 2 module complete all as specified & directed

S&F modular switch, 16 Amps flush type single pole one way complete all as specified & directed.

S&F modular socket outlet 2 in 1, 3 pin, 2 module 5 &16 Amps flush type complete all as specified & directed.

S&F modular fan regulator, electronic type, 5 stepped, 120 watt, flush type , single phase 230 volt including connection complete all as specified & directed.

S & F MODULAR metal flush box suitable for 6 module type complete all as specified and directed.

S & F MODULAR metal flush box suitable for 4 module type complete all as specified and directed.

S & F MODULAR metal flush box suitable for 3 module type complete all as specified and directed.

S & F MODULAR white cover plate with frame suitable for 6 module type complete all as specified and directed.

S & F MODULAR white cover plate with frame suitable for 4 module type complete all as specified and directed.

S & F MODULAR white cover plate with frame suitable for 3 module type complete all as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades, oiling, greasing & make it serviceable by repair / rewinding and painting of ceiling fans complete with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. incl Hanging and connecting up including provision of cable from ceiling rose or connector to fan as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades, oiling, greasing & make it serviceable by repair / rewinding and painting of exhaust fans complete with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. incl Hanging and connecting up including provision of cable from ceiling rose or connector to fan as specified and directed.

S&F in replacement LED tube light fittings decorative ultra slim linear fixture with extruded alluminium heat sink environmental friendly Energy efficient ready to use pack ,1x18/20 Watt ,4 feet, surface mounting type extruded pvc, snap on installers and domestic electronic Driver ,connector block etc. with all accessories internal prewired & including connecting up with 2 core flexible copper conductor cable with suitable size & suitable for and mounting clamps PVC square box 75x75mm - 2 Nos etc complete all as specified & directed.

S&F in replacement energy efficient LED light of 10 Watt of length - 02 Feet long having minimum 1150 Lumen output, wide voltage protection range 140-270 Volt AC housed in extruded aluminum housing (enhances safety) with high quality polycarbonate diffuser including making connection with two core PVC insulated, sheathed copper conductor cable of size 23/0.0076 complete all as specified and directed.

S&F in replacement LED light fitting 10 Watt bulkhead luminaries in high pressure die cast aluminium housing, lumen out put - 700 Lm, colour Temp - 6500 K having Ingress protection - IP 65 fpr dust, water & IK 08 for external impact including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S & F in replacement LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection bracket for street light made out of 40 mm bore GI pipe medium grade not less than 1.2 mtr length bent at 120 degree to shape fixed on pole/wall with and including 50x6mm FI clamps = 02 Nos with nut bolts, washers including painting of clamps with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

All as per srl item No. 89 above but for one 3 pin socket outlet 15 amps, independent, with cables 2.5 sqmm size on independent board 2.5 Sqmm earth wire complete all as specified and directed.

M&L in replacement for concealed submain wiring using FRLSH PVC insulated, unsheathed stranded copper conductor cable two single core of size 4.0 Sqmm of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories along with one run of PVC insulated unsheathed stranded copper conductor of size 4.0 Sqmm as earth continuity conductor complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

Taking down existing old /worn out tube/CFL/bulk head/sketch light fittings of indoor type fixed on wall of any type/size with its all accessories including lamp complete all as specified & directed

S&F in replacement of LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver with suitable size of wire complete including connecting with three core flexible copper conductor cable of suitable size complete all as specified by Engr-in-charge

S&F in replacement LED mirror light fitting 2 feet, 10 watt with high output with opal diffuser 230 V AC decorative type with driver holder and LED lamp including connecting with three core flexible copper conductor cable of suitable size & suitable for mounting clamps PVC square box 75x75mm - 2 nos etc complete all as specified and directed.

S & F in replacement for LED light fitting with box type ultra slim linear LED lighting fixture with co- extruded polycarbonate body environmental friendly, energy efficient tube light complete with all accessories internally pre- wired and including LED lamp 20 watt 01 No and connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

S&F sheet metal enclosure for MCB's 240 volt 12 way single pole and neutral with 200 amps rated bus bar, double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete including taking down of ole unserviceable enclosure complete all as specified and directed.

S&F in replacement MCB double pole 40/63 Amps 'C' curve breaking capacity 10 KA of rating & made from moulded self- extinguishing thermostat plastic and making connection complete all as specified & directed.

Schedule of Credit (MINUS) Rs. 188165.00 B/F from Serial Page No. [Note : Details of items for schedule of credit is given on Srl Page No. ] This amount shall be automatically deducted to arrive at tendered sum

DINESH ELECTRICALS (BID ID -3108516)

Channa Brothers and Co. (BID ID -3107201)

JMD Enterprises (BID ID -3119127)

M/S Garg Sons (BID ID -3117969)