Construction of Residence (Type-IV 01 No., Type-III 01 No., Type-II 04 No.) after Dismantling of 02 No. Existing Store, Construction of Security Hut and Repair of Existing Boundary wall for Proposed 220 KV GIS S/s Mawana, Meerut

Amount

Cartage of ballast,Kankar,Coal, grit, earth or sand etc. including loading and unloading but excluding stacking at pucca roads. For 1st Km. (CSI 3.01a)

Excavation in foundation in ordinary soil (Loam Clay or Sand) including lift upto 1.5m and lead upto 30m and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and sides of the foundation work. (CSI No. 4.01)

Excavation in foundation in soil mixed with moorum/ shingle/ kankar requiring the use of special T&P such as pickaxes, sabbals etc including lift upto 1.5m & lead upto 30m and including filling, watering and ramming of excavated earth into the trenches or into the space between the building & sides of the foundation. (CSI No. 4.02)

Add to Earth work item (SI No. 4.01 to 4.03) for every additional 30m lead or part there of or for every additional 1.5M lift or part there of. (CSI No. 4.04)

Sand filling in plinth including supply of necessary quantity of fine sand from outside the UPPCL premises including watering, dressing etc. Rate to include cost of all materials, labour and T&P etc. required for proper completion of work. (CSI No. 4.05)

Clearing jungle including uprooting of rank vegetations,grass, bush, wood, trees and saplings of girth upto 30cm measured at a height of 1.0m above ground level and removal of rubbish upto a distance of 50m outside the periphery of UPPCL area cleared. (CSI No. 4.08)

Earth filling under floors and/or sub station area including cost of earth when obtained from with in 8 km outside UPPCL area including its roylty and carriage including watering, ramming in 20 cm layers and dressing of earth etc. all complete. (CSI No. 4.10)

Levelling and dressing and making proper slopes including cutting and filling of earth upto a depth 100mm if so required including all labour T&P etc. required for proper completion of the work . (CSI No. 4.11)

Concrete with 4cm gauge stone ballast, coarse sand (F.M. 1.8 to 2.5) & cement in proportion of 12:6:1 in foundations &under floors including supply of all materials, labour and tools and plants etc. required for proper completion. (CSI No. 5.02)

Concrete with 4cm gauge stone ballast, coarse sand (F.M. 1.8 to 2.5) and cement in proportion of 8:4:1 in foundation & under floors including supply of all materials, labour & T&P etc. complete. (CSI no. 5.04a)

Cement concrete with 2cm gauge approved hard stone ballast, coarse sand (F.M. 1.8 to 2.5) and cement in proportion of 4:2:1 including supply of all materials, labour,side shuttering if required and T&P etc. required for proper completion of work. (CSI No. 5.06)

Concreting of 40 mm thick RCC trench covers in mild steel frame work with RCC 1:1.5:3 in Cement,Chopan coarse sand (F.M. 1.8 to 2.5) and 2cm gauge graded hard stone ballast with 3mm thick floating coat of neat cement finish on top of cover complete with all labour, materials and placing the same in proper position at required location of cable trench within the substation area. (CSI No. 5.18)

Concrete work with 40 mm gauge brick ballast obtained from breaking brick bats (brick bats supplied by the department free of cost) in proportion of 12:6:1 as in CSI no. 5.01 including cost of all labour, materials, T&P etc required for proper completion of work. (CSI No. 5.20)

Cement concrete with 2cm gauge approved hard stone ballast, coarse sand (F.M. 1.8 to 2.5) and cement in proportion of 3:1.5:1 including supply of all materials, labour,side shuttering if required and T&P etc. required for proper completion of work. (CSI No. 5.21)

Precast cement concrete door sills, chaukhats boundary posts, shelves and similar small work with cement, approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast in the proportion 1:1.5:3, excluding reinforcement but including fixig the same in position including cost of all other material, labor and T&P . (CSI No. 5.22)

RCC work with cement, approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast like granite, quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3 in lintels of doors and windows, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P. (CSI No. 5.23)

RCC work with cement, approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast like granite, quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3 in slab, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P (CSI No. 5.24)

RCC work with cement, approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast like granite, quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3 in lighter beams i.e. having span upto 6m, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P . (CSI No. 5.25)

RCC work with cement, approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast like granitet, quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3 in heavier beams i.e. having span above 6m, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P . (CSI No. 5.26)

RCC work with cement, approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast like granite quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3 in raft foundation and footings , excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P. (CSI No. 5.27)

RCC work with cement, approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast likegranite, quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3 in RCC pile caping, gantry walls/column foundations and RCC pedestals, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P. (CSI No. 5.28)

RCC work with cement, approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast like granite, quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3 in RCC T beam-slab and column, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P . (CSI No. 5.29)

First class brick work in 1:6 cement and coarse sand (F.M.1.8 to 2.5) mortar in foundation and plinth including supply of all materials, labour & T&P etc. required for proper completion of work. (CSI No. 6.01)

First class brick work in 1:4 cement and coarse sand (F.M.1.8 to 2.5)mortar in foundation and plinth including supply of all materials, labour & T&P etc. required for proper completion of work (CSI No. 6.03)

First class brick work in 1:6 cement and coarse sand (F.M.1.8 to 2.5) mortar in super structure including necessary cutting and moulding of bricks as required and also including honeycomb brick work, thickness of wall not to be less than 1.5 brick. (CSI No. 6.01+6.07)

First class brick work in 1:6 cement and coarse sand (F.M.1.8 to 2.5) mortar in superstructure 230mm thick wall including supply of all materials, labour & T&P etc. required for proper completion of work. (CSI No. 6.01+6.07+6.08)

First class brick work in 1:4 cement and coarse sand (F.M.1.8 to 2.5) mortar in super structure including necessary cutting and moulding of bricks as required and also including honeycomb brick work, thickness of walls of one brick . (CSI No. 6.03+6.07+6.08)

First class brick work in 1:4 cement and coarse sand (F.M.1.8 to 2.5) mortar in superstructure 115mm thick wall including supply of all materials, labour & T&P etc. required for proper completion of work. (CSI No. 6.03+6.07+6.09)

First class brick laid dry in foundation and plinth as in circular soakpit walls of one brick thickness and 2.0 to 3.0M depth including cutting moulding bricks as required including cost of all materials labour and T&P complete. (CSI No. 6.16)

Brick work in foundation & plinth with old dismantled bricks (supplied by department free of cost) and coarse sand of F.M. 1.8 to 2.5 mortar in 1:6 including supply of all other materials, labour, removing mortar & cleaning of old & used bricks,T&P etc complete. (CSI No. 6.18)

Brick work in super structure with old dismantled bricks (supplied by department free of cost) and coarse sand of F.M. 1.8 to 2.5 mortar in 1:4 including supply of all other materials, labour, removing mortar & cleaning of old & used bricks,T&P etc complete. (CSI No.(6.01-6.03) +6.19)

Same as in item 6.18 above but in super structure for 230 mm thick wall. (CSI No. 6.19)

Removal of cement mortar from dismantled bricks and stacking in countable position at place as directed by the Engineer in charge, including cost of all labour and T&P required for proper completion of work. (CSI No. 6.22)

Supply and filling brick bat in soak pit including all labour,material and T&P etc complete. (for 01 soak pit) (CSI No. 6.23)

2.5 cm. thick damp proof course of cement concrete consisting of 1 part cement 1.5 parts approved coarse sand (F.M.1.8 to 2.5), and 3 parts approved 12 mm. graded stone grit and also including liquid water proofing material as approved by the Engineer-Incharge in the proportions specified by the manufacturer. (CSI No. 7.02)

Indian Sal wood wrought framed and fixed including simple, mouldings straight work as in Chaukhats including supply of all materials, labour and T&P etc.required for proper completion of the work. (CSI No. 8.03)

Supply and fixing of 3.5 cm. thick Shisham wood part panelled and part glazed door and window shutter including supply and fixing of wooden cleats and stoppers and including fixing and adjustment of hinges bolts, locks, handles, springs and/or other fittings but excluding their supply and including fixing the glass panes with putty and necessary screws (Glass panes to be 4 mm thick.). (CSI No. 8.22)

As in item 8.22 above but 35 mm. thick Shishum wood fully glazed. (CSI No. 8.24)

Providing and fixing 19 mm thick ply board/block board for wardrobe shutter etc. of Kitply or Century or Duraguard make including teak wood beading around the shutter and including fixing and adjustment of hinges, bolts handle and other fittings but excluidng their supply and including cost of all material labour, T&P etc. required for the proper completion of the work.

Supply and fixing of 35mm thick Shishum wood door and window Jali shutters with panels of heavy quality galvanized iron wire mesh of size 14 x 24 with necessary beading including supply and fixing of wooden cleats and stops and including fixing and adjustment of hinges. but excluding supply of fixtures .(CSI No. 8.41)

S/F Stainless steel Mosquitos proof heavy quality wire gauge (16x24) over window frames and including supply of U.P. Teak wood battens 8cm x 1cm. and including supply and fixing of necessary screws, all materials,labour and T&P etc. required for proper complete. (CSI No. 8.43)

Fixing of Departmental doors & windows shutters including supply & fixing of hinges and other fixtures.(excluding their supply) including all materials, labour & T&P etc. required for proper completion of work. (CSI No. 8.51)

P/F fully Anodized aluminium fixed glazing with HINDALCO or equivalent extruded standard sections14gauge (2.41mm thick) of various cross sections and joints mitred and jointed as shown in drawing including providing & fixing 5.5 mm thick toughened glass with Neoprene beading & aluminium glazing clips all around. The minimum thickness of anodizing on all aluminium sections should be 20 microns with a (+) 2 microns tolerance . The rate should include the cost of fixing the aluminum frame on Teak wood frame or finished wall (RB/RCC/Masonry) surface by means of 80 mm long approved counter sunk screws provided at 500 mm c/c or part there of starting from 100 mm above the bottom in vertical member and 100 mm from both the ends of horizontal top and bottom member excluding cost of Teak frame but including cost of all other material, labour, tools & plants etc. complete. (CSI No. 8.52)

Supply and fixing of 32 mm thick single leaf flush door shutter ( boiled water resistance, phenol maldehide resin bonded, hot pressed factory made) commercial quality to I.S.2202 part-1 (1983) ISI marked including fixing of wooden cleats and stoppers and including fixing and adjustment of hinges,bolts.locks,handles, springs and other fittings but excluding their supply including all materials, labour & T&P etc. required for proper completion of work. (CSI No. 8.57)

Supplying & fixing 24 gauge annodized aluminium sheet of approved quality including cutting, wastage and fixing the same over the wooden door shutters with nails with all material, labour and T&P. (CSI No. 8.63)

Mild Steel or Iron work in heavy sizes such as trusses built up gates, door frames, record, racks roof work gates etc. wrought to required form including holes rivetting or welding where necessary and also fixing in proper position and alignment including cost of all materials supplied by contractor. (CSI No. 9.01)

As in item 9.01 above but when steel is to be provided by the department. (CSI No. 9.02)

TMT/Tor steel in plain work such as reinforced concrete or reinforced brick work (when not included in an over all rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage, bend, hooks and authorized overlapping shall be measured. (Steel shall be arranged by the contractor) (CSI No. 9.03)

As in item 9.03 above but when steel is provided by the Department. (CSI No. 9.04)

Supply and fixing galvanised mosquito proof jali (16x24 gauge) with M.S. flat of 20 x 3 mm. size, on both sides screwed or welded to window or door frame. (CSI No. 9.18)

Providing M.S. Frames work, rack etc for R.C.C. Trench covers and edging with M.S. angles and M.S reinforcement including cutting, bending and welding as per approved drawing. The rate is including cost of all labour, materials etc. as required for proper completion of the work. (CSI No. 9.20)

Grouting of vertical or inclined post of pale/chain/security fencing in true level, alignment and in plumb or inclination as required, including cost of all labour, materials and T&P required for proper completion of work. ( Post and concrete for grouting shall be measured separately) (CSI No. 9.28)

P/F Concertina coil fencing with required dia. 600 mm upto 3 M height of wall between existing angle iron ‘Y’ shaped placed 2.4 M or 3.0 M apart and with 6 horizontal R.B.T. stud tied with G.I. staples and G.I. clips to retain horizontal including necessary bolts or G.I. barbed wire tied to angle iron all complete ( No. of rounds will be 7 to 8 in one Meter length) as per direction of Engineer I/C with reinforced barbed tape (R.B.T.)/ Spring core (2.5mm thick ) TATA make wire of high tensile strength of 165 kg/Sqmm with tape ( 0.52 mm thick ) of supreme make or equivalent and weight 43.478 gm/meter ( cost of MS angle, C.C. blocks shall be paid separately).(CSI No. 9.37)

12 mm thick plaster with cement mortar consisting of one part of cement & four part of coarse sand (1:4), minimum thickness not to be less then 10 mm including supply of all material, labour and T&P etc for proper completion of work. (CSI No. 11.07)

Add for extra labour and materials for plaster over rough face of one brick thick wall. (CSI No. 11.12)

Providing and mixing approved quality of water proofing compound (125 gms.) (DR. FIXIT / RECRON.3S) / hardening material in cement mortar or Concrete as per direction of E/I in proportion as recommended by the manufacturer.

2 cm. thick cement plaster in dado or skirting in 1:2 consisting of one part of cement and two parts of approved coarse sand laid in panels finished with 3mm.floating coat of neat cement or cement and marble dust in ratio of 5:1 including supply of all materials, labour & T&P etc. required for proper completion of the work. (CSI No.11.13)

Providing (12x15) mm section groove in plaster including all material, labour and T&P etc. required for proper completion of the work. (CSI No. 11.16)

6 mm. thick plaster with 1:3 cement & coarse sand including labour, materials & T&P etc. required for proper completion of the work. (CSI No. 11.17)

Making drip coarse (25x12) mm in 1:2 cement and coarse sand including supply of all materials, labour and T&P etc required for proper completion of work. (CSI No. 11.19)

3 mm thick floating coat of neat cement finish including supply of all materials,labour and T&P etc. required for proper completion of the work.( cement consumption 0.044 bag/Sq.m.) (CSI No. 11.20)

2.5 cm thick 1:2:4 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and Excluding 7.5 cm thick base concrete consisting of cement, coarse sand and 4cm gauge I class brick ballast in the proportion of 1:6:12 and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and T&P etc, required for proper completion of the work. (CSI No. 12.02)

4.0 cm thick 1:2:4 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and T&P etc, required for proper completion of the work. without base CC (CSI No. 12.04)

First class bricks on edge floor laid dry, joints sand filled, including preparation of base to proper slope and its ramming including supply of all material labour & T&P etc. required for proper completion of the work. (CSI No. 12.07)

Supply and Laying 8 mm thick glazed floor tiles of Somany, Johnson or equivalent make, , laid with 1:3 cement and approved coarse sand mortar finished with white cement slurry, jointing and polishing complete, including supply of all materials, labour and T&P etc. required for proper completion of the work. (CSI No. 12.11)

Providing and fixing glass strips of 3.15 mm thickness & 25mm depth in joints of floor and skirting at the time of laying floors, flush with floor level including supply of all materials, labour& T&P etc. required for proper completion of work. (CSI No. 12.13)

Providing and laying floor of 8 mm thick vitrified tiles in flooring or skirting of approved brand (Bell, Johnson or equi. make) size of 600x600 mm of approved shade, colour and pattern , laid over base cement mortar 1:4 mix including finishing the joints with white cement mixed with pigment to match the shade of tile including cost of all material, labour and T&P required for proper completion of the work. (CSI No. 12.18)

Providing and laying of 16 mm thick granite ( black/ brown) in flooring or skirting ,of approved shade, colour,size and pattern , laid over base cement mortar 1:4 mix including finishing the joints with white cement mixed with pigment to match the shade of granite floor including cost of all material, labour and T&P required for proper completion of the work, as per direction of Engineer incharge. (CSI No.12.20)

Supply of 80 mm thick I shaped mechanically compressed inter locking cement concrete paver block manufactured by high pressure & controlled vibration machine having plan dimension 200X(160+120 mm) with minimum 5 mm thick toping of O.P.Cement mixed with 25% marble powder. The compressive strength of concrete pavers blocks shall not be less than 30 MPa & 4.5 Kg/No. including cost of all material, labour, T&P etc. required for proper completion of work as directed by Engineer-in-charge but excluding G.S.T. which shall be paid extra as per rules. (CSI No.12.23)

Painting or varnishing new iron work in small areas or new wood work with one coat of ready mixed priming paint and one coat of approved superior quality ready mix paint "Luxol" or equivalent brand or varnish including supply of all materials, labour and T&P etc. required for proper completion of the work. Paint to be used should conform to the I.S. 103-1950. (CSI No. 13.01)

As in CSI 13.01 above but for every coat after first coat. (CSI No. 13.02)

One priming coat and one coat oil bound distemper on new work including supply of all materials,labour and T&P etc. required for proper completion of the work. (CSI No. 13.08)

As in item 13.08 but for every coat after the first coat. (CSI No. 13.09)

Applying Birla or equivalent putty on new interior or exterior surface over one coat of water based cement primer of ICI or equivalent brand for smoothening and levelling of the surface as per requirement and direction of Engineer I/C including cost of all material, labour, T & P etc required for proper completion of work. (CSI No. 13.20)

Painting one coat with APEX or equivalent brand weather coat paint on new wall surfaces (well prepared with Birla putty and one coat of primer ICI or equivalent which shall be paid separately) including through washing with water including cost of all materials, labour, T&P required for proper completion of work. (CSI No. 13.22)

Same as in item no 13.22 above but for every coat of additional APEX or equivalent brand weather coat paint . (CSI No. 13.23)

Dismantling brick work or stone work in lime or cement mortar and including stacking of materials as directed by the Engineer-in-charge within a distance of 60 metres. (CSI No. 15.01)

Dismantling reinforced cement concrete or reinforced brick work, including stacking of dismantled materials as directed by the Engineer-Incharge within a distance of 60 metres. (CSI No. 15.03)

Dismantling cement concrete or brick or granolithic floors including base concrete and including stacking of dismantled materials as directed by the Engineer In-charge within a distance of 60 metres. (CSI No. 15.05)

Dismantling corrugated iron & asbastas roof sheet and stacking of materials as directed by Engg-in-charge within a distance of 60 mtrs. (CSI No. 15.07)

Dismantling of griders, trusses and other steel works including stcking of materials as directed by Engg-in-charge within a distance of 60 mtrs. (CSI No. 15.08)

Dismantling doors or window leaves including stacking of materials as directed by the Engineer I/C within a dist. 60 M. (CSI No. 15.09)

Dismantaling doors and windows chowkhats including stacking of materials as directed by Engg-in-Charge within a distance of 60 meters. (CSI No. 15.10)

Dismantling existing plaster including disposal of refuse as directed by the Engineer In-charge within a distance of 60 metres. (CSI No. 15.11)

Dismantling and re-laying of dry B.O.E. floor including cost of all labour and T&P required for proper completion of work.(labour rates only) (CSI No. 15.18)

Pre-Construction anti-termite treatment, by creating a barrier under and around the columns pits, foundation trenches, under floors, junctions of Walls & floors, around the external perimetre of building, expansion joints, surrounding of pipes and conduits etc. (Plinth area of the building at ground floor only shall be measured as per I.S. 6313 (Part II 1981))with Eldrine emulsifiable 0.2% concentration or any other approved material such as Heptachlore or chlordance will be used. The consumption of emulsion shall be (i) Foundation and masonary @ 5 Ltrs/Sqm, (ii) Back fills in immediate contact of foundation@ 7.5 Ltrs. / Sqm, (iii) Top surface of Plinth filling @ 5 Ltrs / Sqm, ( iv) Junction of walls & floors @ 7.5 Ltrs / Sqm, (v) Soil along external perimetre of building @ 7.5 Ltrs / Sqm (vi) under apron of the building @ 5 Ltrs. /Sqm. The rates includes cost of all materials, labour, equipments, T&P complete. (CSI No. 17.01)

Preparation of sub grade / sub base in proper shape and camber in required width by rolling with road roller in layer of 20 cm. and compaction the same to the optimum moisture content complete for laying brick soling including cost of labour and T&P etc. required for proper completion of work but excluding cost of earth work which shall be paid separately.

Cutting of Road Slab 6 mm wide and 40 mm deep with the help of special cutting tool like stone cutter including cleaning and filling joint with 85/25 grade bitumen after heating bitumen at required temp. Rate including cost of all labour, T&P etc. required for proper completion of work.

Laying cement concrete road slab consisting of 1 part cement 1.5 part approved coarse sand and 3 part approved 20mm down graded stone aggregate over prepared sub grade after its rectification and bringing it to proper camber and shape,finishing with TRIMIX machine ,concrete hardner and making good to the satisfaction of E/I inclduing cost of all materials, labour and T&P etc. required for proper completion of the work. (CSI No. 18.13)

Providing and laying non-pressure NP3 class RCC pipes with collars with stiff mixture of cement mortar in the proportion 1:2 (1-Cement, 2-Coarse sand) including testing of joints including cost of all material, labour, T&P etc. required for proper completion of the work. (CSI No. 18.16) a- 150 mm dia RCC pipe

Providing and laying non-pressure NP3 class RCC pipes with collars with stiff mixture of cement mortar in the proportion 1:2 (1-Cement, 2-Coarse sand) including testing of joints including cost of all material, labour, T&P etc. required for proper completion of the work. b- 300 mm dia RCC pipe (CSI No. 18.16b)

Disposal of rubbish / debris out side the UPPCL area as per direction of Er/in- charge including cartage, labour and materials, T&P etc. required for proper completion of the work. (No. deduction for voids shall be made). (CSI No. 20.16)

Providing and fixing 15 mm dia B-class Jindal,JTC, ISI marked G.I. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.01a)

Providing and fixing 20 mm dia B-class Jindal,JTC, ISI marked G.I. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.01b)

Providing and fixing 25 mm dia B-class Jindal,JTC, ISI marked G.I. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.01c)

Providing and fixing 50 mm dia B-class Jindal ISI marked G.I. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.01)

Providing and fixing 15 mm dia Jindal ISI marked G.I. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes external GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.02)

Providing and fixing 20 mm dia Jindal ISI marked G.I. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes external GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.02)

Providing and fixing 25 mm dia Jindal, JTC, ISI marked G.I. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes external GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.02c)

Providing and fixing 50 mm dia Jindal, JTC, ISI marked G.I. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes external GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.02f)

Making water connection of GI pipe line with GI Mains ( 25 mm to 100 mm ) dia. by providing and fixing Ferrule (25 mm dia) GI union and nipple including cutting and threading the pipe, inspection, testing, cutting and making good the road, executing bond with Nagar maha palika, fixing of pipe line upto the points near the building complete work including supply of all materials, labour and T&P etc. required for proper completion of work. (CSI No. 26.03)

Providing and fixing full way 15mm dia G.M. gate valve with wheel, ZOLOTO make ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.04a)

Providing and fixing full way 20mm dia G.M. gate valve with wheel, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.04b)

Providing and fixing full way 25mm dia G.M. gate valve with wheel,ZOLOTO make ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.04c)

Providing and fixing full way 50mm dia G.M. gate valve with wheel, ZOLOTO makeISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.04f)

Providing and fixing PVC BALL FLOAT VALVE 25 mm dia. WITH BRASS & UNION COMPLETE, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.06c)

Providing and fixing PVC CONNECTION PIPE, 300X15 with 2 brass units ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.09)(a)

Providing and fixing PVC CONNECTION PIPE, 450X15 with 2 brass units ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work.(CSI No. 26.09b)

P/F GI UNIONS NOMINAL BORE 15 mm, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.10a)

P/F GI UNIONS NOMINAL BORE 20 mm, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.10b)

P/F GI UNIONS NOMINAL BORE 25 mm, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.10c)

P/F GI UNIONS NOMINAL BORE 50 mm, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.10f)

Supply and fixing of Syntex or equivalent make water storage tank including all materials, labours, T&P etc required for proper completion of work. (CSI No. 26.12)

Providing and fixing CP BRASS BIB COCK15 mm dia. HEAVY QUALITY ( 400gm) ( L & K and equi.) fittings, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.16a)

Providing and fixing CP BRASS BIB COCK15 mm dia. HEAVY QUALITY ( 200gm) ( L & K or Royal Sonata make) fittings, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.16)

Providing and fixing CP BRASS STOP COCK 15 mm dia. HEAVY QUALITY ( 400gm) ( L & K and equi.) fittings, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.16c)

Providing and fixing CP BRASS SHOWER HEAVY QUALITY ( > 225 gms ) fittings, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.16e)

Providing and fixing CP BRASS Angle Valve HEAVY QUALITY ( L & K or Royal Sonata make) fittings, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.16)

Providing and fixing CP BRASS Piller cock HEAVY QUALITY ( L&K or equi. )fittings, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.16j)

Providing and fixing CONCEALED STOP COCK HEAVY QUALITY ( L&K or equi. )fittings, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.16k)

Providing and fixing of 110 mm dia PVC pipe 6 Kg/ Sq.cm for with special such as Tee, bend, socket, elbow etc including supply of all labour,material,T & P etc complete required for proper completion of work. (CSI No. 26.17)

Providing and fixing first quality white glazed "Orissa" pattern W.C.Pan Hindustan, Cera make. size 580 mm.(Hindustan,Cera Make) with out "P" trap including supply of all materials,labour and T&P etc.complete. (CSI No. 27.01)

Providing and fixing first quality white glazed "European type" pattern W.C.Pan Hindustan, Cera make. size 580 mm.(Hindustan,Cera Make) with out "P" trap including supply of all materials,labour and T&P etc.complete. (CSI No. 27.02)

Providing and fixing PLASTIC SEAT COVER COMPLETE WITH PLASTIC LID FOR EUROPEAN TYPE WC ISI MARKED including supply of all materials,labour and T&P etc.complete. (CSI No. 27.04)

Providing and fixing 550X400 mm wash hand basin of white glazed earthern ware first quality I.S.I. marked (Hindustan,Neycer / Cera make) including supply of all materials, labour and T&P etc. required for proper completion of the work. (CSI No. 27.08)

Providing and fixing 10 litres low level PVC flushing cistern, COMPLETE WITH ALL FITTINGS including supply of all materials, labour and T&P etc. required for proper completion of the work. (CSI No. 27.12)

Providing and fixing in position 32 mm. dia P.V.C. flush pipe. for W.C. with unions, bends etc. including supply of all materials,labour and T&P etc.required for proper completion of the work. (CSI No. 27.13)

Providing and fixing in position 32 mm. dia P.V.C. WASTE PIPE FOR WASH BASIN. including supply of all materials,labour and T&P etc.required for proper completion of the work. (CSI No. 27.14)

Providing and fixing 600 mm x 450 mm beveled edge mirror of Atul,Kiran makeglass with Indian polish 6.50 mm thick complete with back of 600 mm x 450 mm x 6 mm hard board sheet fixed to wooden cieats with C.P. brass screws and washers including supply of all materials, labour and T&P etc.required for proper completion of the work. (CSI No. 27.15)

Providing and fixing 750 mm x 20 mm size C.P. brass towel rail of approved quality including brackets including supply of all materials,labour and T&P etc. required for proper completion of the work and cutting and making good the wall plaster etc. required for work. (CSI No. 27.16)

As in item no. 27.16 above but for 600 mm x 20 mm size. (CSI No. 27.17)

Providing and fixing soap dish chromium plated with brackets fixed to wooden cleats with brass screws including supply of all materials,labour and T&P etc.required for proper completion of the work. (CSI No. 27.19)

Providing and fixing M.S. holder bat clamps of approved design including supply of all materials,labour and T&P etc. required for proper completion of the work for 100 mm. dia pipe. (CSI No. 27.20a)

Supply and fixing CP Nahani Trap India make of heavy approved quality complete with CI grating, including supply of all materials,labour and T&P etc. required for proper completion of the work. (CSI No. 27.21a)

as above but for 100 mm.PVC trap.

Providing and fixing 100 mm dia white glazed "P" or "S" trap including cement concrete and all materials, labour cartage T&P etc.required for proper completion of the work.(For W.C.) (CSI No. 27.23)

Providing and fixing CI GRATING 100 mm dia including all materials, labour cartage T&P etc.required for proper completion of the work. (CSI No. 27.25)

Providing and fixing Stainless Steel sink 610x450x200 mm Heavy Quality( ISI MARKED ) including all materials, labour cartage T&P etc.required for proper completion of the work. (CSI No. 27.26)

Providing and fixing false ceiling at all heights with integral densifiedr Armstrong false ceiling tiles of Size 595x595 x12 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as perBS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on interlocking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6 SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 1632 mm reveal profile white/black),comprising of main-T runners of size 15x42 mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross-T of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in- Charge. 26.23.1 With 12 mm thick Armstrong Miniral Fobre Sound Absorbing Sheet (CSI No. 28.30)

S/F surface/flush mounting 8 ways SPN distribution board Without additional metal door without MCB complete in all respect as per directed at site by E/I. (CSI No. PWD 1024)

Supply and wiring of submain with two number 6 sq.mm FR PVC insulated 1100 V grade multistrand single core copper conductor cable in 25 mm dia heavy duty (2 mm thick) PVC conduit concealed in wall complete with one number 4 sq.mm FR PVC insulated multistrand copper conductor cable as earth continuity wire etc. complete in all respects. (CSI No. PWD 222C)

Wiring point for call bell with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in pvc conduit pipe concealed in the wall, complete with 14 SWG copper earth continuity wire and piano type bell push or 2 pin socket etc., complete in all respect including matching colour wash.

Wiring point for exhaust fan with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in pvc conduit concealed in the wall, complete with 14 SWG copper earth continuity wire, GP Box , 15 A piano type switch and ceiling rose on 3 mm thick phenolic laminated backelite sheet etc. complete in all respect including mathcing colour wash.

S&F of 32 Amp. 240 V DP metal clad rewireable type switch fuse unit on M.D.F.E.G. / Teak wood board complete in all respect.

Supply and burying of 600mm x 600mm x 3mm copper plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia G.I. pipe and funnel for watering and one earthing lead of one no. 8 to 10 SWG copper wire in 15mm dia G.I. pipe up to switch board (from appron to switch board the cost of G.I. pipe and copper wire will be extra) 30cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal/coke and salt at least 150mm thick alround etc. complete in all respect

S/F surface/flush mounting 4 ways SPN distribution board without MCB complete in all respect as per direction of E/I. Cat A

Supply and fixing of electronic fan regulator( Modular) 120-280 V. ISI marked, on the existing switch board including making connections, required material, labour T&P etc. for proper completion of work to the satisfaction of Engineer in charge of work.

Wiring point for two ways light with 1.5 sq. mm.FRLSH PVC insulated multistrand ingle core copper conductor cable in pvc conduit pipe concealed in the wall, complete with 14 SWG copper earth continuity wire and two numbers two ways piano type switches & ceiling rose/angle/batten holder on 3 mm thick phenolic laminated backelite sheet etc, complete in all respect, as directed, including matching colour wash.

Supply and fixing of switch box 100 x 100 x 50 mm size of approved make made up of 1.0 mm thick ISI Marked G.P.sheet All 4 corners folded & spot welded for screw and holes plugged with PVC Nylon Caps . Two or more holes for pipe try of 25.4 mm on upper and lower sides of the box. Holes shuld be semi-shuttered type and itted ith heavy brass Earth Piller duly screwed & brand name should be embossed. Box lushed in wall including cutting of brick work, fixing it to the level with cement sand mortar, including atching colour wash with s/o all materials, labour and T&P required for proper completion of work as directed at site by the Engineer in charge.

Same as Ele sch.2018,159but for 150x150x65 mm size.

Same as Ele sch.2018,159 but for 200x250x65 mm size.

Add for light / fan points with modular type switch in place of piano type switch

Add for 2 way light point with modular switches in place of piano type switches.

Add for plug point with modular switch & socket in place of piano type switch & socket.

Add for HPMV/Exhaust fan point with modular type switch in place of piano type switch.

Add for Call bell point with modular type bell push in place of piano type bell push.

Supply and Fixing of aluminium fittings with screw for doors and windows etc. (e)10mm dia 150mm long Tower Bolts

Supply and Fixing of aluminium fittings with screw for doors and windows etc. (h) 100mm long Door Handle

Supply and Fixing of aluminium fittings with screw for doors and windows etc. (h) 150mm long Door Handles

Supply and Fixing of aluminium fittings with screw for doors and windows etc. (i) Aluminium Door Stoppers or Cleats (Rubber & Long Scew)

Supply and Fixing of aluminium fittings with screw for doors and windows etc. (j) ISI Marked Door Belan 10mm dia 300mm long

Supply and fixing of chromium polished iron fitting with screws for doors and windows etc.(a)CP Tower bolt 250 mm long 10 mm dia rod

Supply and fixing of chromium polished iron fitting with screws for doors and windows etc.(b)CP Tower bolt 100 mm long 10 mm dia

Supply and fixing of chromium polished iron fitting with screws for doors and windows etc.(d)GI HINGES 100 mm SIZE 12 gauge.thick

Supply and fixing of chromium polished iron fitting with screws for doors and windows etc.(e) Iron door spring

Supply and fixing of chromium polished iron fitting with screws for doors and windows etc.(f)CP iron handle 100 mm

Supply and fixing of chromium polished iron fitting with screws for doors and windows etc.(g) CP iron L-drop 20 cm long & 16 mm dia with nuts-bolts & clamps.

Providing and fixing 20 mm dia ISI Approved CPVC pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.20)

Providing and fixing 25 mm dia ISI Approved CPVC pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.21)

Supply and fixing of geo-textile membrane of heavy quaiity around soakpit/pipe. The rate are inclusive of all material,overlapping minimum 300mm,cartage,labour,T&P required to complete the work in all respect. (CSI No. NSI 1)

Supply and laying of 25m heavy duty- PVC conduit pipe (2mm thick) complete with bends and other accessories as required and 14 SWG fish steel wire etc. in slab along with binding with reinforcement before concreting and plastering complete in all respect. (CSI No. PWD 282A)

S/F of 32 Amp. 240V SPN metal clad rewireable type switch fuse on M.D.F.E.G./Teak wood board complete in all respect. (Cat-"B") (CSI No. PWD 302 CAT B)

Wiring point for light with 1.5 sq. mm FR PVC insulated multistrand single core copper conductor cable in PVC conduit pipe concealed in the wall, complete with 14 SWG copper earth continuity wire, Modular type switch and ceiling rose/angle/batten holder on 3mm thick phenolic laminated backelite sheet etc,complete in all respects,as directed,including maching colour wash.

Wiring point for fan/fresh air fan with 1.5 sq. mm FR PVC insulated multistrand single core copper conductor cable in PVC conduit pipe concealed in the wall, complete with 14 SWG copper earth continuity wire, Modular type switch and ceiling rose/angle/batten holder on 3mm thick phenolic laminated backelite sheet etc,complete in all respects,as directed,including maching colour wash.

Wiring point for Plug with 1.5 sq. mm FR PVC insulated multistrand single core copper conductor cable in PVC conduit pipe concealed in the wall, complete with 14 SWG copper earth continuity wire, Modular type switch and ceiling rose/angle/batten holder on 3mm thick phenolic laminated backelite sheet etc,complete in all respects,as directed,including maching colour wash.

S&F of 6 Amp to 32 Amp. SPMCB (10 KA) C Curve cat-B

S&F of 63 Amp. S.P. Isolator cat-B

Supply and fixing of power plug with 15A/250 volt flush type switch and 5 pin 15A/250V flush type universal socket in suitable M.S. box of 175mm x 100mm x 50mm size with phenolic laminated bakelite sheet cover 3mm thick fixed with brass machine screw and cup washer

Supply and fixing hexagonal/Round G.P.fan box ofapproved make made up of 1.0 mm thick ISI Marked G.P.sheet spot welded Four to Eight holes of 25.4 mm for pipe entry of the box. Holes should be semi-shuttered type with 0.5 mm G.P. Sheet made upper & lower cover duly screwed fitted with 300 mm round zink coted M.S Bar X 12 mm & brand name should be embossed. Fixing with wiring conduit laid in the R.C.C. roof before concreting alongwith supply of all aterial, labour, T&P etc. required for proper completion of the work.

Supply and fixing of 2/3/4 ways round steel junction box confirming to ISS for 25mm dia PVC conduit concealed in wall, keeping its level upto plaster duly provided with proper size cover screwed as directed at site by Engineer-in-charge with supply of all material, labour & T&P etc. required for proper completion of work.

Supply and fixing of switch box made up of SWG (1.5mm) thick M.S. sheet of 175x100x65 mm size. duly painted with red oxide primer and flushed in wall including cutting of brick work, fixing it to the level with cement sand mortar including matching colour wash with s/o all materials, labour and T&P required for proper completion of work as directed at site by the E/I.

Providing & Fixing LED Tube light set of 22 watt. Of Approved make,

KULDEEP KUMAR CONTRACTOR

M/S GREESH CHAND