SPL REPAIR TO DRAINS, BLDG NOS. TA-06, T-132, ROOF OF GUARD POST AND CONSTRUCTION OF BOUNDARY WALL AT CERTAIN LOCATIONS OF SEVOKE ROAD MIL STN

Amount

Dismantling plain or corrugated steel sheeting any thickness, complete all as specified and directed.

Dismantling floor hearth or wall tiling and stone slabs including cement mortar bedding ( but not backing ) removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) removing rubbish off the premises etc complete all as specified and directed

Demolition of cement concrete (un reinforced) of any description and in in any position not otherwise specifically provided for, removing rubbish off the premises etc complete all as specified and directed.

Demolition of concrete (reinforced) of any description and in in any position not otherwise specifically provided for, removing rubbish off the premises etc complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exceeding 1.50 Sqm each and removing complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from frames) exceeding 1.5 sqmtr but not exceeding 4 sq m each and removing complete all as specified and directed.

Taking down shutters from frames not exceeding 1 sq m each, and removing complete all as specified and directed.

Taking down aluminium shutter with frame without taking shutter from frame area n .exc 2 sqm each complete all as specified and as directed.

Dismantling of Bricks (laid flat or on edge) or brick tiles in floors, channels,kerbs, aprons, etc. (each layer) , laid, bedded and pointed in any mortar, separating and stacking serviceable bricks for reuse and removing unserviceable portion complete all as specified and directed.

Demolition of brickwork built in cement mortar, separating and stacking serviceable bricks for reuse and removing rubbish off the premises etc complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position, complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs of any thickness including cover fillets complete all as specified and directed.

Taking down cement plaster or lime plaster on walls /ceiling of any description from concrete or brick wall etc including raking out joints, hacking for key, scrubbing down with water and disposing off the retrieved debris as directed including necessary scaffoldings etc complete all as specified and directed

Taking up or down 15 mm bore steel water tubing and connections complete all as specified.

Dismantling PVC/HDPE water tank of capacity 500 Litre, setting aside, cleaning thoroughly, refixing in position and connecting complete all as specified and directed

Dismantling expanded metal of any description weight not exc. 4 Kg per square metre as directed

Surface dressing n exc 15 cm deep and getting out in soft/loose soil complete all as specified and as directed.

Excavating in trenches not exc 1.5m wide and n.exc 1.5 m in depth, for foundations, etc, or for shafts, wells, cesspits, manholes, pier holes, cable trench etc and not exceeding 10 square meter on plan and getting out in soft/loose soil complete all as specified and directed.

Returning filling in with approved excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level nexc. 1.5 metre above the starting point complete all as specified and directed.

Materials and Labour for broken stone or boulder hardcore of gauge n exe 63mm deposited, spread and levelled in layers n exe 15cm thick, watered and rammed to a true surface.

Materials and Labour for plain cement concrete (1:3:6) type C1 (20mm graded crushed stone aggregated) as in back filling of pressed steel frame complete all as specified and as directed.

Materials and Labour for plain cement concrete (1:4:8) type D-2, using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

Materials and Labour for plain cement concrete (1:3:6) type C-2, using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

Materials and Labour for plain cement concrete (1:3:6) type C-2, using 40mm graded stone aggregate as in surface channel and drain including necessary formwork complete all as specified and as directed.

Materials and Labour for plain cement concrete (1:2:4) type B-1, using 20mm graded stone aggregate as in drains coping and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and as directed.

Materials and Labour for finishing cement concrete surface even and smooth using extra cement complete all as specified and as directed.

Materials and Labour for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. all as specified and as directed.

Materials and Labour for formwork to sides of concrete foundation, footing, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beam; and similar work; vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed.

Materials and Labour for formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished square, rectangular or polygonal surfaces of concrete complete all as specified and directed

Materials and Labour for formwork to faces of sides and soffits of floor or roof beams, cantilevers, lintels, shelves including supports, overhangs, etc for rough finished flat surfaces of concrete complete all as specified and directed

Materials and Labour for formwork to soffits of suspended slabs such as roof slab, floor slabs, landings and similer works, for rough finished flat surfaces of concrete, thickness of slab not exc 200 mm, complete all as specified and directed

Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in slabs and shelves supported on walls, beams and columns in floors, roofs and landings etc, any thickness complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc; basement slabs under reamed pillars and mass concrete complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in column, pillars, piers, post and struts complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

Materials and Labour for precast reinforced cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate as in in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces etc, any thickness, placed in position and set in cement mortar 1:4 complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

Materials and Labour for TMT bars 6 to 8 mm dia , as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Materials and Labour for TMT bars 10 mm dia and over, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Materials and Labour for TMT bars 6 to 10 mm dia in stirrups, spacers and binders, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Materials and Labour for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240

Fixing only Steel work in tubular trusses including special shaped washer etc. complete using old steel obtained from dismantling including necessary welding wherever required for alteration.

Materials and Labour for rolled mild steel Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel') complete all as specified and as directed.

Supply & fixing mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

Supply & fixing rolled mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment (Fe 290 Gde-E 165) complete all as specified and as directed.

Supply & fixing rolled mild steel section including hollow section as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates FE-290 Gde E-165. Complete all as specified and directed.

Supply & fixing Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to steel trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165.

Supply & fixing mild steel expanded metal cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9 mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel memberss n .exc 4 kg/sqm complete all as specified.

Supply & fixing 0.80 mm thick plain galvanised mild steel sheeting of grade O (120gm/Sqm zinc coating) in ridges hips, valley gutters, drip and straight flashings with grade including dismantling old rusted sheets complete all as specified and directed.

Supply and fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

All as per item No 52 here-in-before but except sheets complete all as specified and directed. (Note :- Old serviceable sheets obtained from dismantling shall be reused)

Supply and fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws , complete all as specified and directed.

Supply and fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based 0.50 mm colour coated Mangalore pattern tile profile sheet of any colour having tensile strength of 345 Mpa as in roof covering/cladding to wall fixed with self tapping screws, complete all as specified and directed.

Materials and labour for preparing of new wooden surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Materials and labour for preparing of new steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Materials and labour for preparing of old painted steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement mortar (1:6) for laying of floor finishes complete all as specified and directed.

Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 20mm thick screed bed or bedding layer of cement mortar (1:6) for laying of floor finishes complete all as specified and directed.

Materials and labour for coloured 350x250x7-8/ 450x350x7-8 mm thick glazed ceramic tiles on vertical surfaces such as skirting,dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick backing coat in cement mortar (1:4) , complete all as specified and directed.

Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,on vertical surfaces such as skirting,dado and risers to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 10mm thick screed bed or bedding layer of cement mortar (1:4) complete all as specified and directed.

Materials and labour for Vitrified Ceramic tiles of light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & incl 15 mm th screed bed in CM 1:6 complete including Necessary dismantling complete all as specified and as directed.

All as per Item No.63 above but as in skirting,dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick backing coat in cement mortar (1:4) , complete all as specified and directed.

Materials and labour for Vitrified Ceramic tiles of dark shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 but not exceeding 1 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & incl 15 mm th screed bed in CM 1:6 complete including Necessary dismantling complete all as specified and as directed.

Materials and labour for 20mm thick granite slabs of any type (table rubbed and polished) on cooking platforms and like, set and jointed in net cement slurry and pointed in white cement (1:2) using marble dust with admixture of pigment to match shade of granite including necessary moulding at edges laid over and including 20mm thick cement mortor screed bed in cement mortor (1:6) complete all as specified and directed.

Materials and labour for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand Complete all as specified and as directed

Materials and labour for 75 mm thick plain cement concrete (1:4:8) type D2 using 40 mm graded stone aggregate as in sub-base of floors etc. finished the surface of concrete even and rough complete all as specified and directed.

Materials and labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in hard standing, plinth protection, path etc. finished the surface of concrete even and smooth without using extra cement, complete all as specified and directed.

Materials and labour for brick work with fly ash bricks modular size straight or curved on plan exc. 6mtr mean radius, built in cement mortar 1:4, complete all as specified and directed.

Materials and labour for brick work with fly ash bricks modular size straight or curved on plan exc. 6mtr mean radius, built in cement mortar 1:6, complete all as specified and directed.

Materials and labour for brick work with fly ash bricks old size straight or curved on plan exc. 6mtr mean radius, built in cement mortar 1:6, complete all as specified and directed.

Materials and labour for brick work except bricks with using old serviceable fly ash bricks any size straight or curved on plan to any radius built in cement mortar 1:6, complete all as specified and directed.(Old seviceable bricks obtained from demolition shall be reused)

Materials and labour for Bricks, sub class B, laid on edge in floors;old size brick, Bedded and jointed in Cement mortar 1:6 and pointed in Cement mortar 1:3 complete all as specified and as directed.

All as per Item No.74 above but except bricks complete all as specified and directed. (Old seviceable bricks obtained from demolition shall be reused)

Materials and labour for Bricks, sub class B, laid flat in floors;old size brick, Bedded and jointed in Cement mortar 1:6 and pointed in Cement mortar 1:3 complete all as specified and as directed.

All as per Item No.76 above but except bricks complete all as specified and directed. (Old seviceable bricks obtained from demolition shall be reused)

Cutting chases, pinning in brick wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concrete water tubing or concrete conduit wiring etc and making good, cutting not exc 10cm girth complete all as specified and as directed.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing, complete all as specified and directed.

Supply and fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed.

Supply and fixing 125 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified.

Supply and fixing flush door shutters 30mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Supply and fixing 30mm thick second class hard wood glazed and skeleton shutter, open rebated and prepared to receive glass gauze etc, divided into squares (with sash bar), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass exc., size of members of shutter as specified in SSR part-I, sec 8 clause 8.24(a), supplied and fitted to chowkats, complete all as specified and directed.

Supply and fixing 35mm thick second class hard wood glazed and skeleton shutter, open rebated and prepared to receive glass gauze etc, divided into squares (with sash bar), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass exc., size of members of shutter as specified in SSR part-I, sec 8 clause 8.24(a), supplied and fitted to chowkats, complete all as specified and directed.

Materials and labour for 6mm thick plywood, 5 ply, grade BWR,type BB fixed with screws to timber frame work as in cup board ,fix with brass screws and cups complete all as specified.

Materials and labour for 18/19mm thick Particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work as in cabinet, cup board,moduler kitchen etc. including external teak wood lipping all round, 6mm thick fixed with nails complete all as specified.

Materials and labour for second class hard wood plain fillets. square, rectangular or triangular in section, wrought, secured with nails or brads of sectional area exc 3 sqcm and not exc 6 sqcm complete all as specified and directed. .

Materials and labour for Second class hard wood in scantlings, clean swan, timber framed and fixed, complete all as specified and as directed.

Supply and fixing in repairs Aluminium (Extruded section body) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed.

Supply and fixing in repairs 150mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed.

Supply and fixing anodised powder coated aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

Materials and labour for providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws. complete all as specified and directed

Materials and labour for providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed

Material and labour for coloured aluminium anodised louvers ventilators of frame of section 63.5mm x 38.1mm x 1.01 mm or appropriate equivalent section with aluminium members for holding glass strips including necessary locking arrangement, 4mm thick frosted glass strips etc complete all as specified and directed.

Supply and fixing Aluminium anodized barrel tower bolts of extruded section, 200 mm long, complete all as specified and directed.

Supply and fixing Aluminium anodized barrel tower bolts of extruded section, 150 mm long, complete all as specified and directed.

Supply and fixing Aluminium anodized barrel tower bolts of extruded section, 100 mm long, complete all as specified and directed.

Supply and fixing extruded aluminium alloy handles, fabricated type, anodized, 150 mm size , complete all as specified and directed.

Supply and fixing extruded aluminium alloy handles, fabricated type, anodized, 100 mm size , complete all as specified and directed.

Supply and fixing for 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Supply and fixing for 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Supply and fixing Mild steel butt hinges, medium weight, cold rolled 100 mm size , complete all as specified and directed.

Supply and fixing MS butt hinges medium weight 75mm long, complete all as specified and directed.

Supply and fixing Hasp and staple, safety type, aluminium anodised 75mm including bolt to hinge plate and fixed with screws complete as specified and directed.

Supply and fixing 2 lever brass lock, cupboard grade 1, 50mm size complete as specified and directed.

Supply and fixing stainless steel 02 Lever door lock of approved make complete as specified and directed.

Supply and fixing stainless steel 04 Lever door lock of approved make complete as specified and directed.

Supply and fixing 40mm dia, cupboard knobs, brass, polished fixed with nut, screw and washer of mild steel, bright finished complete as specified and directed.

Supply and fixing in repair continuous (Piano) hinges mild steel bright finish or electro galvanised, width of flaps when open 30mm complete as specified and directed.

Supply and fixing Aluminium power coated fancy curtain rails plain or colour 20to 25 mm dia as approved with teak wood finishing brackets and knobs complete all as specified.

Supply and fixing 4 mm thick sheet glass, ordinary quality and glazing with oil putty in squares n.exceeding 0.50sqm in each pane , complete all as specified and directed.

Supply and fixing 5.5mm thick plain glass and glazing in square not exc 0.50 Sqm in each pane complete all as specified and directed.

Supply and fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Materials and labour for rendering 15mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

Materials and labour for rendering 15mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces of drain, finished even and smooth without using extra cement, complete all as specified and directed.

Materials and labour for rendering 20mm thick in two layers of 10 mm thick each in cement mortar (1:4) on fair faces of brick work or concrete surfaces,WPC shall be mixed with morter of top layer, finished even and fair, complete all as specified and directed. (Note: WPC shall be measured and paid separately as supply only)

Materials and labour for flush pointing to brick walls in cement mortar (1:3) on brick work or concrete surfaces,complete all as specified and directed.

Supply only integral Water Proofing Compound of approved make.

Materials and labour for preparation of new/old plastered surfaces of wall and applying 1mm thick wall care putty of approved make complete all as specified and directed.

Materials and labour for applying three coats of white wash on new wall surface including preparation of surface, complete all as specified and directed.

Materials and labour for preparation of new plastered surfaces of walls and applying two coats of weather proof antifungal exterior emulsion paint (as per manufacturer instructions) of approved colour over a coat of alkali resistant primer over 1mm thick wall care putty complete all as specified and directed.

Materials and labour for preparation of new plastered surfaces of walls and applying two coats of weather proof antifungal exterior emulsion paint (as per manufacturer instructions) of approved colour over a coat of alkali resistant primer complete all as specified and directed.

Materials and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper of approved colour with roller over one coat of primer after preparation of surface complete all as specified and directed.

Materials and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper of approved colour with roller over one coat of primer over 1 mm thick wall care putty of approved make complete all as specified and directed.

Materials and labour for complete removal of existing paint from surfaces of wall and applying two coats of weather proof antifungal exterior emulsion paint (as per manufacturer instructions) of approved colour over a coat of alkali resistant primer over 1mm thick wall care putty complete all as specified and directed.

Materials and labour for complete removal of existing paint from surfaces of wall and applying applying two coats of oil bound distemper of approved colour with roller over one coat of primer complete all as specified and directed.

Materials and labour for 605X605mm anodised aluminium snap grid frame work for false ceiling including hangers 2.5 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including supply and fixing 4mm thick Decorative non asbestos fibre cement boards fixed or laid/ inserted to aluminium frame work as in ceiling complete all as specified and directed. Note:- The size of aluminium main and cross tee shall be 40mm x25mm x2mm and size of angle shall be 25mm x 25mm x 2mm or higher)

Materials and labour for 8/9mm thick PVC ceiling/wall panels of interlocking types, width 250/255 mm with lamination design and exc 60% of PVC content including necessary H-joints, internal/external corner trim, corner cove,F/J edge trims where required fixed with hidden screws and including steel/wooden frame work of width 50mm complete all as specified and directed.

Supply and fixing 15 mm bore medium grade galvanized steel water tubing with all fittings, fixed to wall/ceiling or laid in floor complete all as specified.

Supply and fixing in repairs, stainless steel sink with drainage board, 1 mm thick for kitchen or laboratoty with plugs, waste pipe, washers, including cantilever cast iron brackets, connecting union to waste pipe etc including bedding in cement mortar to dwarf wall, overall size 915x460mm with bowl size 410mm x 330mm x160mm with 40 dia mm CP waste coupling and PVC waste pipe complete all as specified and directed.

Supply and fixing repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with CP brass bracket guard railing 60cm long complete all as specified and directed.

Supply and fixing Snow White vitreous china wash down water closet pan (pedestal pattern) 'S' Trap One piece EWC 'S' concealed including soft close seat cover, internal twin flush fittings and making all necessary connection as specified and directed.

Supply and fixing in repair 10Ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed.

Supply and fixing vitreous china, white, flat back wash hand basin of size 525 mm x 415 x 140 mm thin Rim counter top basin including counter with jet black granite with and including CP brackets (of suitable size) including 32 mm bore brass chromium plated waste coupling, 32 mm dia PVC waste pipe etc complete all as specified and directed.

Supply and fixing in repairs vitreous china bowl urinal flat back size 355 x 340 x 535 mm white (minimum) with gratings and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipes ) etc

Supply and fixing for 450mm long PVC connections 15mm size with PTMT nuts, complete all as specified and directed.

Supply and fixing in repairs, 15mm cromium plated two way Bib taps, cast copper alloy with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

Supply and fixing 15mm bore dia Stop cock cast copper fancy type chromium plated alloy screwed down high pressure with crutch or butter fly handle serwed both ends for iron pipe or for unions complete all as specified and as directed.

Supply and fixing 15mm bore dia angle cock cast copper fancy type chromium plated alloy screwed down high pressure with crutch or butter fly handle serwed both ends for iron pipe or for unions complete all as specified and as directed.

Supply and fixing Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

Supply and fixing CP Soap dish holder including CP screws complete all as specified and as directed.

Supply and fixing CP Soap dispenser with glass bottle including CP screws complete all as specified and as directed.

Supply and fixing CP Towel ring, square type including CP screws complete all as specified and as directed.

Supply and fixing CP Toilet paper holder including CP screws complete all as specified and as directed.

Supply and fixing Concussive push button taps of cast copper alloy, screwed for iron pipe and fixed.

Supply and fixing in repairs CP Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified.

Supply & fixing CI Floor trap 100mm diameter of outlet, with gratings, including jointing to waste pipe fixed in PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) complete all as directed.

Supply and fixing 32mm bore Bottle trap of chromium plated having minimum water seal of 25mm .

Supply and fixing PVC (SWR) pipes 150mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

Supply and fixing PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

Supply and fixing PVC (SWR) bends any radius 110mm bore with access door, complete all as specified and directed.

Supply and fixing PVC (SWR) junction single, (Single T) equal or unequal, 110mm bore, complete all as specified and directed.

Supply and fixing PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

Supply and fixing PVC (SWR) bends any radius 75mm bore with access door, complete all as specified and directed.

Supply and fixing PVC (SWR) junction single, (Single T) equal or unequal, 75 mm bore complete all as specified and directed.

Materials and labour for surface preparation including cleaning the surface, treating of construction joints, filling of honey combs with polymer modified mortar (cement : sand: approved ploymer (Asian/Beger/Shalimar/STP) for filling cracks up to 3mm using approved crack seal, bigger cracks, damaged potions and hollow areas shall be repaired with polymer modified cement morters complete as per manufacturer instructions. Manufacturer:- ASIAN/ BERGER/ SHALIMAR/STP.

Materials and labour for Roof treatment by application of non toxic polyurethane modified acrylic based single component (P U Roof Coat) solvent free, cold applied polyurethane modified elastomeric waterprooofing membrane with excellent UV resistant capacity as per ASTM D6083 [a water based 100% acrylic elastomeric emulsion polymer latex coating used as protective coating for roofs] after preparing the surface by cleaning and repairing the roof cracks by cement & sand mortar (1:4), with antishrinkage mortar if any, apply two coats along with a priming coat (two coats of P U Roof Coat and one coat of primer coat compatible with main product as per manufactures specification) and reinforced with 20 gms Geotextile Fleece, including the cost of primer coat and base preparation, tools & plants complete as per manufacturer instructions. Manufacturer:- ASIAN/ BERGER/ SHALIMAR. Note:- (i) Application of roof treatment shall be done by the authorized applicator of manufacturer as approved by GE. (ii) Contractor shall be obtained the Guarantee from the manufacturer for 10 years and submit to the department alongwith the Guarantee as specified in CA.

Supply and applying to concrete surfaces single component, fibre reinforced shrinkage compensated, polymer modified structural grade repair mortar of thickness 40mm. The repair mortar should have a compressive strength of 45 N/sqmm , flextural strength 7 N/sqmm and tensile strength 2.5 N/sqmm at 28 days and curing the treated surface with polymer based curing agent having moisture retention as per ASTM C 156, drying time 3 hours at 23 degree C temparature, complete with tools & plants as per manufacturer instructions. Manufacturer:- FOSROC CHEMICALS/ PIDILITE INDUSTRIES /STP LTD ). Note:- (i) Work shall be done by the authorized applicator of manufacturer as approved by GE.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc

Taking down carefully old serviceable Main Switch, DB's consisting of MCBs wooden/GI/MS sheet board etc for kept in store and for later use all as directed.

Taking down carefully unserviceable sub main wiring of any size/core/type including making good the disturbed surfaces all as directed.

Taking down ceiling fans/exhaust fan of any size,dismantling blades and removing fan and blades to MES store complete all as specified and directed.

Materials and labour for concealed point wiring with two runs of FRLS PVC insulated unsheathed, 1100 V grade cable multi stranded copper conductor of size 1.5 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 1.50 sqmm green in colour as earth lead, drawing through in and including PVC rigid conduit of size not less than 20mm, with all fittings & accessories including provn of MS sunk terminal box of appropriate size suitable for switch fixed flush to wall for mounting switch, sockets, fan regulators etc with 3mm thick hylum sheet top cover with screws & cup washers for one light / fan point / call bell complete. NOTE : Cost of making good the disturbed surfaces (if any) matching with the existing surface is deemed to be included in the unit quoted rates. all as specified and directed.One light/fan/call bell point controlled by one switch one way 5 Amps

All as per Item No.164 above but for One 2/3 pin socket outlet 5/6Amps on independent board

All as per Item No.164 above but for One 2/3 pin socket outlet 5/6 Amps on the same board with other switches.

All as per Item No.164 above but for one switch socket combination 15/16 Amps on independent board with cable 2.5 sq mm size and earth wire 2.5 sqmm

Supply and fixing Switch piano, flush type, single pole, one way switch 5 Amps.

Supply and fixing Switch socket combination 2 in 1, 5 Amps flush type.

Supply and fixing Switch socket combination multipurpose 5 A/16 Amps,5 in 1, flush type.

Supply and fixing Ceiling rose surface bakelite 3 terminals 65x50mm all as directed.

Supply and fixing Socket outlet 3 Pin, 5 Amp flush type universal, 240 volts, complete all as specified all as directed.

Supply and fixing Bell Push Flush type 5 Amp, 240 volt all as specified.

Supply and fixing Bell Ding-Dong AC 230 V Single Pole complete all as specified and as directed.

Supply and fixing in repair ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

Supply and fixing electronic step regulator (speed regulation in 5 steps) suitable for ceiling fan 1200 sweep/1400 mm, 120 Watt complete all as specified and directed.

Supply and fixing in repair energy saving and environmental friendly long life LED security/street Light fittings 25 watts, made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover, IP 66 protection, inbuilt driver, connecting with suitable size copper wire, with 32mm bore 1 m long medium grade GI bracket made to shape complete all as specified and as directed.

Supply, fixing and connecting in repair exhaust fan metal body complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 230mm complete all as specified and as directed.

Taking down existing unserviceable light fitting and Supply and fixing new decorative type surface and wall mounted 20 Watt LED batten light fittings, 4 feet long, with aluminium housing and integrated electronic driver, fixed to walls/ceiling, environmental friendly, energy efficient ready to use pack .

Taking down existing unserviceable light fitting and Supply and fixing new decorative type surface and wall mounted 9/10 Watt LED batten light fittings, 2 feet long, with aluminium housing and integrated electronic driver, fixed to walls/ceiling, environmental friendly, energy efficient ready to use pack .

Taking down existing unserviceable light fittings and Supply and fixing new recess mounted downlighter, 15 watts, 230 volts, including driver, necessary fixing arrangement and connecting with suitable size flexible copper wire complete all as specified and as directed.

Supply and fixing MCB distrubution board TPN 4way, double door, IP 42, IK-09, sheet steel, phosphatised,powder coated with 200 amps rated bus-bar,neutral link,earth bar and din rail, 440 V, including taking down existing unserviceable DB with MCBs complete all as specified and directed. by Engineer-in-charge.

Supply and fixing MCB Single pole, 240 volts 5 to 32 Amps 10 KA rupturing capacity, C series

Supply and fixing MCB TPN, 440volts 40 Amps, 10KA rupturing capacity, C series

Materials &Labour for submain concealed wiring with two single core PVC insulated, unsheathed, stranded copper conductor of size 6.0 Sqmm one single core PVC insulated, unsheathed stranded copper conductor 6.0 Sqmm green in colour as earth continuity conductor drawn into and including PVC conduit (medium grade) with all fitting & accessories complete all as specified and directed by Eng-in-Charge .

Supply and laying XLPE insulated PVC inner sheathed, armoured with galvanized steel strip or wire heavy duty underground cable with stranded aluminum conductor 1100 volt grade of size 16 Sqmm 4 Core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing complete all as specified and directed including taking down old unserviceable XLPE cable with brick protection and complete all as specified and as directed.

Materials and labour for 50 mm outer dia double wall corrugated (DWC) HDPE pipe, ISI marked for enclosing cable below ground/road surface to a required depth including suitable size couplers for jointing of pipe all as per site requirement etc complete all as specified and directed.

Supply and fixing test point terminal block made of gun metal or phosphorus bronze of size 75x75x25 mm, drilled and screwed including 3 nos. 8 mm dia 25 mm long hexagonal head screw fixed on wall complete all as specified and as directed

Materials and labour for air termination, single pointed aluminium rod 12 mm dia and 300 mm long all as specified and as directed

Materials and labour for aluminium strip 25x3 mm with saddles and fixing screws etc for roof conductors and down conductors above ground specified and as directed

Materials and labour for GI strip 32 x 6 mm buried in ground for interconnection of earthing complete all as specified as directed.

Materials and labour for porcelain insulator suitable for fixing earthing strip to the wall / floor etc all as specified and as directed

Materials and labour for earthing complete with galvanized steel pipe electrode 40mm bore , medium grade, 2.5 meters length, buried directly and preferably vertically in ground with top edge not less than 1.25 meters below ground level connected with earthing lead galvanized iron strip of size 25x5 mm connected to galvanized earth pipe by means of bolts, nuts, checknuts and washer of galvanized iron including PCC (1:2:4) type B1 precast RCC cover slab with suitable handle made of 6mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanized steel tube for watering with one end fix with cast iron funnel and wire-mesh , with protection pipe of 32 mm dia light grade galvanized steel tubing upto 7.5 meters length for drawing earthlead including common salt, charcol , bentonite in alternate layers etc, complete all as shown in EP number 2 of SSR part-1 including testing on completion and including taking down old u/s earthing & testing complete all as specified and as directed.

M&L for Advance encapsulated compound based Chemical earthing CPRI tesed maintenance free , pipein -pipe technology upgraded (Zinc coated). , Zinc & Alloy coated (80 -100) microns with pure zinc (99.9%) & Alloy coating (200-250) microns.Earthing system conforming IS 3034. The outer and inner pipe should be 76.2mm and 41.9mm dia respectively of 3 mtrs long zinc coated with with additional special alloy coating 300mm on top side for additional protection of the terminal . The annular space between the pipes to be filled up with Compact fill (CF) (Crystalline Conductive) mixture which should be machine pressed in the pipes not disintegrate or collapse when outer pipe corrodes . The inner pipe should be extended with terminals for connectivity.The job includes digging the pits ,lowering the pipe in pipe earth electrode,filling of pure conductolite back filling compound (BFC Conductolite ) having excellent moisture retaining capacity in 250 mm around the electrode min 4 bags of 25 KG per pit per unit. The BFC should be eco friendly it should not contain environmently hazardous material/metal having ROHS certification from NABL accredited lab.The earth pit should be provided with a FRP earth pit cover for protection and safe guard of terminals. The material of earth electrode should have good electrical conductivity & anti corrosion property in wide range of soil conditions. The job also include M & L for in PCC(1:3:6) type C-1 around the FRP cover for support and foundation and colouring the PCC work with desired colour.complete all as specified and directed. Note :- (i) Design of earth electrode should be of pipe-in-pipe technology . (ii) Contractor have to submit literature of earth electrode and get the make approved of GE before procurement. (iii) The earth electrode shall be CPRI tested to withstand short current test for 60kA rms for 1.0 second and 150kA for peak current.

M/S STANDARD CONSTRUCTION CO

SRI SURAJIT SENGUPTA

D.D. BROTHERS

RAJU AICH