Partitions in the HoD Cabin, Faculty Room, and Lab of the School of Business in the new CET building

Amount

Part A : Civil Works

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately):

(a) For fixed portion

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge.

(a) Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete :

(a) 100x60x2.50 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete

Providing and fixing partition upto ceiling height consisting of G.l. fram and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.l. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture’s specification and direction of engineer in charge all complete

75 mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming to IS: 2095: (part I): 2011 (Board with BIS certification marks) sqm

Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 24 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss crossing Gl wire etc. complete as per directions of Engineer-in-Charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge

20 mm nominal dia Pipes

15 mm nominal dia Pipes

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15 mm nominal bore

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

100 mm nominal size dia

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement: 4 coarse sand):

(a) Shelves (Cast in situ)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour :

New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre

Part B : Electrical Works

Supply and drawing following sizes of FR PVC insulated copper conductor,single core cable in the existing surface/recess/pVC conduit as required make Havells/Finolex/RR Kabel or equvalent

i) 2 x 4 sqmm + 1x 4sqmm earth wire

ii) 4x 6 sqmm + 2x 6sqmm earth wire

iii) 4 x 10 sqmm + 2x 6 sqmm earth wire

iv) 4x 16sqmm + 2x 6sqmm earth wire

Supplying and fixing following modular type switch/socket on the existing swith box/cover including connection etc.as required make legrand or equivalent

(a) 15 Amp Switch

(b) 15 Amp socket

c) 5 amps Switch

d) 5 amps socket

Supply and fixing modular blacking plate on the existing modular plate & switch box excluding modular plate as required

Supplying and , fixing of following modules GI boxes along with modular base & cover plate for modular switch in recess etc as required make havels crabtree

i) 1 or 2 Module

iii) 8 module

Supplying and fixing of following ways surface/recess mounting vertical type 415V TPN MCB distribution board of sheet steel dust protected duly powder painted inclusive of 200A tinned copper busbar common neutral link earth bar din bar for mounting MCBs ( But without MCBs and incommer) as required ( Note: Vertical type MCCB TPDB is normally used where 3 phase outlet are required

i) 4 way (4+12) double door

ii) 12way (4+36) double door

Supply and fixing 5amps to 32amp 240/415V 10KA C curve miniatutre ckt braker suitable for inductive load of following poles in the existing MCB DB complete with connection testing and commissioing etc as required

i) Single pole

(ii) Double pole

iii) Triple pole

iii) Triple and neutral

Proding and fixing following rating and breaking capacity and pole MCCB with thermo magnetic release and thermal spreader in exiting cubicles panel board including drilling holes in cubicles panel, making connection etc as required

i) 100 A ,30KA FP MCCB

Supplying and laying of CAT-06 computer cable in existing conduit steel/PVC conduit and termination etc. as required make D-link

Supply and drawing following pair 0.50mm dia FRLS PVC insulated annealed copper conductor unarmored telephone cable in the existing surface/ recessd steel/PVC conduit as required

i) 2 pair

Supplying and fixing following modular type switch/socket on the existing swith box/cover including connection etc.as required make Anchor/ Goldmedel/Kolor or equvalent

i) Telephone socket outlet

Supply and fixing of following sizes of medium class PVC conduit along with accessories in the surface/recess including cutting the wall amking good the same in case of recess conduit required

i) 20mm dia

i) 25 mm dia

Supply and drawing following sizes of FR PVC insulated copper conductor,single core cable in the existing surface/recess/pVC conduit as required make Havells/Finolex/RR Kabel or equvalent

i) 5X35sqmm sqmm

Supplying and fixing of computer point RJ-45 modualr type in compatiable box along with cover plate etc. complete make legrand or equvalent

Supply delivery and fixing of metal one way enclosure for 4 pole MCCB as required

i) 4 pole metal enclosure

DHIRAJ THAKURIA (BID ID -3260329)

NARAYAN DEKA (BID ID -3260034)