Construction of ICAI Bhawan - Raipur Situated at plot no. A-130, Sector-11A. kamal Vihar, Raipur for The Institute of Chartered Accountants of India (ICAI) Bhawan at Raipur (CG)

TOTAL AMOUNT WITH CORRECTION FACTOR (0.973) AS PER OM OF

Grand Total (DSR+ Non DSR) (A):- 22,26,47,060

Sl. No. DSR 2023 Item of Work Unit Quantity DSR RATE Non-DSR RATE DSR Amount Non-DSR Amount

1 Clearing & Grubing

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings

of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish

outside the periphery of the area cleared and clearing grass and removal of the rubbish outside

the periphery of the area cleared complete in all aspects.

2 Earthwork Excavation

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in

foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including

dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil

and disposal of surplus excavated soil as directed, within a lead of 50m.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or

stacked materials.

3 Sand Filling

Supplying and filling in plinth with sand under floors, including watering, ramming,

2.27 consolidating and dressing complete.

4 BACK FILLING

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc.

2.25 in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and Cum 714.75 196.00 1,40,091.00

watering, lead up to 50 and for all lift.

5 Earth filling

Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical

2.25 (a) transport upto a lead of 5km also including ramming and watering of the earth in layers not Cum 10608.00 700.50 74,30,904.00

exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift.

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone

aggregate 40 mm nominal size derived from natural sources).

7 Anti-termite Treatment

(A)Chemicals The chemical used for the soil treatment shall be of the following with the

concentration shown is aqueous emulsion.Imidachloprid 30.5% SC, Doses: 2.1 ml per lit of

(B) Method of Treatment1.Treatment of Top Surface of Plinth Filling 2.Treatment at Junction

of the wall and the floor 3.Treatment of Soil Along External Perimeter of Building 4.

Treatment of Soil Surrounding Pipes, Waste and Conduits.

8 Plinth protection

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand

(zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived

4.17 from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well sqm 168.87 749.30 1,26,534.29

rammed and consolidated and grouted with fine sand, including necessary excavation, levelling

& dressing & finishing the top smooth.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

9 6.4 superstructure above plinth level up to floor V level in all shapes and sizes in

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 121.04 9105.95 11,02,184.19

Providing and laying in position ready mixed or site batched design mix cement concrete for

reinforced cement concrete work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in

recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve

durability and workability without impairing strength; including pumping of concrete to site of

5.33 laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing

and reinforcement as per direction of the engineer-in-charge; for the following grades of

concrete. Note: Extra cement up to 10% of the minimum specified cement content in design

mix shall be payable separately. In case the cement content in design mix is more than 1.10

times of the specified minimum cement content, the contractor shall have discretion to either

re-design the mix or bear the cost of extra cement.

5.33.1 All works upto plinth level

5.33.1.2 Concrete of M30 grade with minimum cement content of 350 kg /cum cum 661.96 9655.70 63,91,678.92

5.33.2 All works above plinth level upto floor V level

5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum cum 1097.46 9860.40 1,08,21,384.72

Add for using extra cement in the items of design mix over and above the specified cement content quint

11 Reinforcement

Steel reinforcement (Fe-500D) for R.C.C. work including straightening, cutting, bending,

placing in position and binding all complete upto plinth level.

Steel reinforcement (Fe-500D) for R.C.C. work including straightening, cutting, bending,

placing in position and binding all complete above plinth level.

All shuttering of RCC members shall be as per DSR 2023 Subhead 5. As per Drawings &

Directions of the Engineer in charge.

a 5.9.1 Foundations, footings, bases of columns, etc. for mass. Sqm 518.40 392.15 2,03,290.56

b 5.9.3 Suspended floors, roofs, landings, balconies and access platform Sqm 4965.81 927.25 46,04,547.32

c 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers Sqm 3987.25 736.40 29,36,207.95

d 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 1968.03 961.30 18,91,864.84

e 5.9.7 Stairs, (excluding landings) except spiral-staircases. Sqm 490.66 764.95 3,75,326.92

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping

f 5.11 etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every

additional height of 1 metre or part thereof (Plan area to be measured).

5.11.1 Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) Sqm 2500.00 384.30 9,60,750.00

12 1:6 Cement Mortar

Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10

average compressive strength in super structure above plinth level up to floor V level in.

13 1:4 Cement Mortar

Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10

average compressive strength in super structure above plinth level up to floor V level in.

14 12 mm Plastering (1:6 Cement Plaster)

13.1.2 12 mm cement plaster of mix. sqm 5958.63 333.35 19,86,309.31

15 15 mm Plastering (1:6 Cement Plaster)

13.2.2 15 mm cement plaster on the rough side of single or half brick wall of mix. sqm 5958.63 383.00 22,82,155.29

16 6 mm Plastering (1:3 Cement Plaster)

13.16.1 6 mm cement plaster of mix. sqm 1506.00 300.45 4,52,477.70

17 Water Proofing

Providing and applying fibre reinforced elastomeric liquid water proofing membrane with

resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in

three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid

22.22A (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing sqm 1850.00 563.10 10,41,735.00

liquid (dry film thickness of complete application/system not less than 500 microns). The

operation shall be carried out after scrapping and properly cleaning the surface to remove loose

particles with wire brushes, complete in all respect as per the direction of Engineerin - Charge.

18 Vitrified Floor Tiles

Providing and laying Double chargeVitrified tiles in floor in size (600 x 1200 mm) with water

absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in

all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand)

11.41A.1.3 jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement sqm 1471.60 1577.15 23,20,932.36

and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only .

Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness,

leveling system and rubber mallet for placing the tiles gently and easily.

19 Vitrified Floor Skirting

Providing and laying Vitrified tiles in different sizes (1000x1000 mm), with water absorption

less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in

11.46.4 skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), sqm 222.00 2162.60 4,80,095.90

jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement

& matching pigments etc. complete.

20 Matt/Antiskid finish Vitrified Floor Tiles

Providing and laying Glazed Vitrified tiles Matt/Antiskid finish for floor in size (600 x 1200

mm) with water absorption less than 0.08% and conforming to IS:15622, of approved brand &

manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4

11.41A coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with

white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond

cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required

thickness, leveling system and rubber mallet for placing the tiles gently and easily.

11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size

21 Glazed Ceramic Floor tiles

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300mm or more

(thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of

approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20

mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @

3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc.,

22 Ceramic glazed wall tiles

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to

be specified by the manufacturer), of approved make, in all colours, shades except burgundy,

bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps

and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing

with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with

pigment of matching shade complete.

23 Granite flooring

Providing and laying flamed finish Granite stone flooring in required design and patterns, in

linear as well as curvilinear portions of the building all complete as per the architectural

drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4

(1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement

slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge.

24 Carpet Flooring

Supply, Installation, providing & fixing of tufted, 1/10 gauge, 100% type nylon, cut pile 800-

1,000 GSM roll carpet, which is suitable & recommended to be used in an Auditorium

application. The selected carpet have inbuilt “ PP Woven Cloth ” and “ Action back ® ️” for

better performance. It have a standard length & width of 25m and 4m respectively. The carpet

MR have a minimum pile height of 7mm, with a total height of 9mm, also have a minimum pile sqm 550.00 1800.00 9,90,000.00

weight of 1000g/m ² and a minimum total weight of 2000g/m ² , Fire resistance of Bfl-s1,to

ensure adequate quality for the said usage. Rates quoted are inclusive of minimum 6mm layer

of foam backing. The carpet also have color fastness standard of minimum 4 or more for

rubbing (wet or dry), water or light.

25 Engineered Hardwood Flooring

Providing and laying in position 14 mm thick Engineered Hardwood Flooring of size

14*215*2200 mm having smart lock tongue and groove joints to secure long lasting joint. The

material comprising of three layers, Top Layer is of genuine hardwood surface, the middle

layer is of pine or spruce ribs laid transversely and the third layer is stabilizing bottom layer.

The Floor is finished on top with seven course of UV curved formaldehyde free lacquer. The

planks are installed on foam and polythene sheet on top of the under floor and stuck to one

another using adhesive in the groove of the board all complete including all accessories

(Skirting, Profile) etc

26 False Ceiling

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum)

false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having

moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS

8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85%

(minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot

dipped galvanised iron section of 0.33 mm thick(galvanized @ 120 gram per sqm including

both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of

size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of

26.26 length 600 mm to form grid module of size 600 x 600 mm, suspended from ceiling using

galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer

diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-

shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size

24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of

plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work

shall be carried out as per specifications, drawing and as per directions of the Engineer-in-

Charge. With fully perforated 12 mm thick micro tegular edged or 10 mm thick square edged

GRG false ceiling tiles.

With fully perforated 12 mm thick micro tegular edged or 10 mm thick square edged GRG

false ceiling tiles.

27 Wooden Slats

Supply & installation of wall paneling of Anutone slats surco high density fiberboard made

out of pure pinewood particles, Fr Grade - Pure Pinewood Particle core with test BS 476 part

5, - Melamine laminated finish, perforated wooden grooved HDF slats L16-2 (2 mm grooves

@ 8 mm centers), tongue-groove edge for a seamless look of lineal dimension size 128 mm x

2440 mm x 16 mm thick having density 700 Kg /m3, weight -9 Kgs/m2 ,2mm Front Side

Sound Abstroctor &1076 Distractor Hole nonwoven acoustic to be pasted on slats surco is to

be installed by using GI strut system. The technical parameters are as follows Core Variants -

Fiberboard, Climate (OC RH) – 50, 70 Light reflectance – 75%,Green (RC %) – 25, Hygiene

(VoC, Clean room) – Low, Class 1, NRC-0.85,Strength, Load capacity (Kg) - Anti sag, Ball-

Impact. The concealed wall paneling system shall include GI Wall channel (WC25) having

thickness 0.45mm, length 3600mm, unequal flanges of 15 & 20mm and web of 25mm should

be fixed along the perimeters of the wall with nylon sleeves and suitable fasteners at every

300mm centers. Then fixed Main channels (MC45) having thickness 0.8mm, length 3600mm,

equal flanges of 15mm and web 45mm from the side wall & fixed at every 1200mm centers

with GI cross channel(CC25) having thickness 0.45mm, length 3600mm, knurled web 35mm,

depth of 25mm and equal flanges 9.5mm is fastened to the Main channel in the direction

perpendicular to the Main Channel at every 600mm centers. The framework will maintain 50 /

75 mm gap from the walls. Now clad the wooden Anatone slats surco on the CC 18 with the

help of center & edge clips to get better locking of slats. The tongue & groove are to be

properly aligned to get flush look . Synth Anuton poly fiber PF 5 x 50 wool of 500 gsm to be

filled between the horizontal & vertical studs as in filler with the help of wire / stick 7

adhesive. Test certificate of the use products shall be submitted after procurement of materials.

28 Wool Magnesia Bonded

Supply & installation of Anutone pinewood wool magnesia bonded soak fabric cord binary /

Triangle design of selected colours (ref colour chart ) kerfs edge fabric wrapped ,pinewood

fibers panels of size 600 X 600/ 1200 x 25 mm having density -400 Kg /m3 weight -10 Kg / mt

2 installed by using GI strut system. The GI strut works includes cross channels CC50 having

thickness 0.45 mm , length 3600 knurled web 50, depth 50 mm & base 100 mm equal flanges

of 13 mm is fastened to wall positioned horizontally in a regular manner at 600mm centers.

PVC vinyl core UV treated H - spline having thickness 2 mm & length 2400 mm to be fixed or

using Z bar or H spline on the back or edge of panels / tiles & similar on the back of channels

perpendicular to the cross channels CC50 at 600mm centers. Kerfed edge fabric wrapped

factory panels shall be then inserting into the H - spline against wall to perfect fit. Panels shall

be back lined with acoustical infill of anutone Synth PF 5 x 50 mm thick adhered to the wall

using stick 7 adhesive. The technical parameters are as follows: core variant - pinewood fibers.

Fire class 1 & P Acoustic - NRC 20 mm C10 - 0.85, Climate - OCRH - 50,90 Termite

resistance - yes light reflectance - colour dependent, Green RC% - 10, Hygiene ( Voc, Clean

Room ) - Low, Strength, Load Capacity ( Kg ) - Ball impact. Test certificate of the use products

shall be submitted after procurement of materials.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) (Frame

size 50 x 100 mm)solid door/ window/ Clerestory windows & other Frames/ Chowkhat

comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate

and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum

toxicity index of 12 for 100gms) fabricated with miter joints after applying PVC solvent

cement and screwed with full body threaded star headed SS screws having minimum frame

density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge),

minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance

to spread of flame of Class A category with property of being termite/borer proof,

water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash

fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S

hold fast/lugs or SS dash fasteners shall be paid for separately).

30 WPC Shutter

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) (30 mm

thick) solid plain flush door shutter of required size comprising of virgin polymer of K value

58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice

husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having

minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N

26.87.1 (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and sqm 11.03 4346.70 47,922.37

resistance to spread of flame of Class A category with property of being termite/borer proof,

water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required

size with necessary full body threaded star headed counter sunk S.S screws, all as per direction

of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be

paid separately).

31 Acoustic Door

Providing & Fixing of ARAI certification Acousticaly treated auditorium door with heat

activated intumescent fire seal strip mounted on the door frames on all three sides and one coat

of anti-termite fire retardant primer. Door shutter consisting of 77mm thick door shutter having

minimum 32 dB acoustic cum 120 min. fire rating having infill of 50mm thick resin bonded

Polyfibre wool of 24kg / M3 density with FR Acrylic Sealant sandwiched between two 9mm

thick (Starpan Make or Approved equivalent) Magnesium Oxside boards a 100% without

asbestos, Brucite and Meerschaum having a density not less than 1150kg/M3 and thermal

conductivity 0.14 W/m* K faced with 3.4mm thick commercial ply 1mm laminated on both

sides with heat activated intumescent fire seal strip of size 10mm x 4mm mounted in the

grooves having hardwood lipping including door closer, CE & EN 1154 certified 2 hrs fire

rated with 10 years warranty tested to BS 476 Part 22 and as per approved make &

single/double leaf panic exit devices, CE & EN 1125 certified 2 hrs fire rated tested in

accordance with BS 476 Part 22. complete in all respect as per the direction of the Engineer-in-

32 Aluminum Door

Providing and fixing lockable Sliding - Folding system Aluminum works for doors applications

of TOSTEM make. The extruded aluminium sections should be made from Grade 6063-T5 &

Anodized with Texguard coating, silicon coated to suit marine atmosphere. All profiles should

be None insulated Profiles. Corner connection will be Butt joint with Screw using Nano

gaskets for sealing. All other major accessories should also be made by the same manufacturer.

All panels will have no visible hinge or connecting hardware and shall not be connected on any

side of the outer frame. Intermediate profile spaces must be equipped with pinch resistant

gasket. EPDM gaskets should be used in all meeting points instead of Brush Pile. The outer

frame Depth will be 72mm. All materials which are used should be corrosion-resistant so that

they are good functioning in different environments and that there are no negative influences

either on the aluminium or on the surface treatment. Glass to be used is 16 MM TOUGHENED

ET 4350 ST GOBAIN. All hardware shall be TOSTEM make only.

The system should allow the application of glazing or panels with thickness up to 8mm. The

external perimeter of aluminium sections should be Anodized with Texguard coating. The

system should qualify Air tightness ASTM E283:200 mm at 175Pa of pressure; Water tightness

ASTM E331:2000 Pa. System should have a 10-year warranty on properties, functionality and

design, within restrictions defined by technical specifications of anodizing & 1-year warranty

on wearing parts. Warranty realistically only applies to normal and foreseeable use.

33 Fire rated door Frame

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x

60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet (Zinc coating

not less than 120 gm/sqm) suitable for mounting 120 minutes Fire Rated Glazed Door Shutters.

The frame shall be filled with mineral wool Insulation having density minimum 96Kg/sqm.

The frame will have a provision of G.I. anchor fastners 14 nos (5 each on vertical style & 4 on

horizontal style of size M10 x 80) suitable for fixing in the opening along with factory made

template for SS ball bearing hinges of size 100x89x3 mm for fixing of fire rated glazed shutter.

The frame shall be finished with an approved fire resistant primer or powder coating of not less

than 30 micron in desired shade as per the directions of Engineer - in- Charge.

34 Fire rated door Shutter

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 minutes Fire rating

conforming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory

approved by Engineer-in-Charge, with suitable mounting on door frame, consisting of vertical

styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out

9.162 of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/ sqm) duly filled mineral wool SQM 43.79 12017.90 5,26,203.75

insulation having density minimum 96 kg/cum and fixing with necessary stainless steel ball

bearing hinges of size 100x89x3 mm of approved make, including applying a coat of approved

fire resistant primer or powder coating not less than 30 micron etc all complete as per direction

of Engineer-in-Charge.

Supplying and fixing-Fixing of Un-plasticised poly vinyl chloride (UPVC) (FENESTA/NCL

VEKA LTD.) Casenent Door-60-Series duly manufactured using UPVC reinforced profiles of

60mm x 55mm x 2.5mm for outer frames 102mm x 60mm x 2.5mm casement Door Sash

profile and 74mm x 60mm x 2.5mm mullion peofile capable of mounting single glazing

system, structurally reinforced with hot dip galvanised up to 50 microns of minimum thickness

of 2.0 mm prefabricated & welded through fusion welding the door sash shall be fitted with

MR 12mm thick WPC Board of Greenply make duly fixed with EPDM weathering seal resistant sqm 143.53 11633.97 16,69,847.56

accessories like clipping locking system made of aluminium 1 No. per set of sashes and th

esystem isto be installed at the site using anchor fasteners, silicon rubber sealant,easy

glazing/deglazing at site etc. including cost and conveyance of all material, accessories, labour

charges, materials and product conforming to ASTM D 638-14,EN-447-95 and other

applicable codes and standards. (Ref.-Office of the Engineer-In-Chife (CIVIL), Odisha Nirman

Soudha, Bhubaneswar. Lt. No-16100)

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand

and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic

21.18 floor spring type fixing arrangement and making necessary holes etc. for fixing required door sqm 11.34 5325.90 60,395.71

fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper

etc.to be paid separately).

37 UPVC Sliding door

Providing and fixing System Aluminum works for Sliding doors and windows with 35mm

visible aluminum section width in the center mullion. The extruded aluminum sections should

be made from Grade 6063 & Anodized with Texguard coating , silicon coated to suit marine

atmosphere. All profiles should be None insulated Profiles. Corner connection will be Butt

joint with Screw using Nano gaskets for sealing. All other major Accessories should also be

made by the same manufacture. All Slider doors & windows will be center locking. Integrated

Anti-lift in slider panel, EPDM gaskets should be used in slider windows & doors in all

meeting points instead of Brush Pile. The outer frame Depth will be 72mm. All materials

MR which are used should be corrosion-resistant so that they are good functioning in different sqm 8.64 8379.89 72,402.23

environments and that there are no negative influences either on the aluminum or on the

surface treatment. The system should allow the application of glazing or panels with thickness

up to 8mm. The external perimeter of aluminium sections should be Anodized with Texguard

coating, the system should qualify Airtightness 8 m3/h.m2 at 75Pa of pressure, Water tightness

150 Pa, Wind load resistance 1200 Pa. System should have a 10-year warranty on properties,

functionality and design, within restrictions defined by technical specifications of anodizing &

1-year warranty on wearing parts only applies to normal and realistically foreseeable use. All

Slider doors & windows will be center locking .

38 UPVC Sliding windows

Two track two panels sliding door with Aluminium channel for roller track, wool pile, zinc

alloy (zamak) powder coated handle on every panel along with multi-point locking system,

adjustable nylon rollers with SS 304 body. Using R3 series with frame (55 mm & above)

x (40 mm & above) & sash (30 mm & above) x (74 mm & above). (Height upto 2.5 metre).

Providing and fixing double glazed hermetically sealed glazing in aluminium windows,

ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap,

21.1 including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both sqm 0.00 4997.70 -

primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-

in-charge complete.

40 UPVC Ventilator (1000 x 600)

Providing and fixing of UPVC (Un Plasticized Poly Vinyl Chloride) Ventilator made out of

hollow- chambered UPVC Sections having isolated drainage and reinforced throughout with

galvanized steel. The ventilator shall be made out of UPVC sections having an overall size of

60mm x 60mm thickness. Structurally Reinforced with hot dip galvanized up to 50 microns of

minimum thickness of 1.2mm with locking system. Prefabricated & welded through fusion

welding the window outer frame & sash shall be fitted with 5mm thickness Pin-Head glass of

reputed brand (Saint Gobain Glass), weathering sealant & Accessories like louvers made by

brand. The outer frame is to be installed at the side using anchor fastener, Silicon Rubber

Sealant. At least 15 years manufacturing warranty for discoloration, wrapping, mechanical

failures, Shrinkages, Rooting Corrosion etc. with a quality Certificate from relevant

departments of that government through the Dealers including of all materials and abounds etc.

Complete as per directions of Engineer in charge.

41 UPVC Ventilator (600 x 600)

Providing and fixing of UPVC (Un Plasticized Poly Vinyl Chloride) Ventilator made out of

hollow- chambered UPVC Sections having isolated drainage and reinforced throughout with

galvanized steel. The ventilator shall be made out of UPVC sections having an overall size of

60mm x 60mm thickness. Structurally Reinforced with hot dip galvanized up to 50 microns of

minimum thickness of 1.2mm with locking system. Prefabricated & welded through fusion

welding the window outer frame & sash shall be fitted with 5mm thickness Pin-Head glass of

reputed brand (Saint Gobain Glass), weathering sealant & Accessories like louvers made by

brand. The outer frame is to be installed at the side using anchor fastener, Silicon Rubber

Sealant. At least 15 years manufacturing warranty for discoloration, wrapping, mechanical

failures, Shrinkages, Rooting Corrosion etc. with a quality Certificate from relevant

departments of that government through the Dealers including of all materials and abounds etc.

Complete as per directions of Engineer in charge.

42 Toilet Cubicle

Providing & fixing Greenlam Sturdo Essentia Toilet Cubicle (of following standard dimension

which includes 600mm door size width) made of heat, bacteria, water, chemical, scratch,

impact and anti bacterial, anti virus, anti fungal resistant 12mm thick solid compact laminate

panels tested by Shriram Test House. Finish of the compact laminate should be Suede / *Raw

Silk, which includs doors, pilasters & intermediate panels finished with approved texture/shade

as per the detail drawings & as per IS 2046 (Indian Standard) and as per fire retardant BS-

476/97 standard. The product should have Green Guard Certificate. Reduction of virus in 2

hours and 24 hours when tested by ISO 21702: 2019 standard. This also includes providing and

fixing in position necessary hardware made out of Nylon Polymide Grade-6 & Aluminium

powder coated top rail as per manufacturer ’s specifications & Architects instructions like (1)

Nylon Door Knob, (2) Nylon Gravity hinges, (3) Nylon Thumb turn lockset indicators, (4)

Aluminum Powder Coated Top Rail, (5) Nylon Coat Hooks, (6) U-Channels, (7) Nylon

Adjustable Foot, (8) Noise Deafening Tape etc. (9) Screws & wall Plugs. The top fitting should

consist of Aluminium Powder Coated top rail which will get fixed with Mid & End

pilasters.All other hardware & screws will of stainless steel in 304 Grade with satin finish. Top

rail is extruded Aluminium will be powder coated or anodized (Grade 6063 Micron

Aluminium). All pilasters are supported by grade-6 Nylon Polymide Thermoplastic palm

design pedestal footing with non corrosive steel inserts. The base diameter 65mm and neck

diameter of 33mm anchored to the floor with grade 304 satin finish stainless steel screws with

push fit capping at a clearance height of 150mm. Model is Heat and Bacteria Resistant

Polymide in which aluminium U-Channel will be used for the fixing of intermediate panels to

43 Toilet Urinal

Made of 12 mm thick compact laminate thotal height 1195 mm , Depth 450 , Gap from ground

500 to 600 mm. Hardware:-Stainless steel L clamp is used to attach the divider to the wall,

stainless steel L clamp hardware fittings along with Su 316 screws are used to fix the Urinal

partitions on the wall.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats,

square or round bars etc. including priming coat with approved steel primer all complete.

45 Synthetic enamel Paint (Iron work)

13.61 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. sqm 7.92 155.90 1,234.73

46 S.S. RAILING

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates

etc., including welding, grinding, buffing, polishing and making curvature (wherever required)

and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing

10.28 with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required kg 3000.00 772.40 23,17,200.00

size, on the top of the floor or the side of waistslab with suitable arrangement as per approval

of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be

considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

47 13.45 Finishing walls with textured exterior paint of required shade. sqm 2504.81 223.60 5,60,076.41

48 MCM (Modified Clay Material)

Supply & Fixing of MCM Modified Clay Material ‐ MCM R Series Brick (087089) ‐ 222 x 63

mm of PHOMI make or equivalent, as per company standard dimension, pattern, color as

specified, manufactured through unfired patented (Ref: US patent 8505840 B2 & European

Patent 2157139) manufacturing technology, bonded together by using low heat temperature and

having CE approval with the thermal conductivity of 0.0590 W/M.K — EN 12667 (2001),

thermal resistance of 0.0568 M2 K/W — EN 12667 (2001) and Fire Insulation ‐ Class A —

MR ASTM E84 ‐ 15. The product should be patented from United States and Europe and with sqm 210.00 6129.55 12,87,204.53

certifications by IGBC, Singapore Green Label and China Green Building material. MCM

Materials should be fixed with suitable Cement/ Polymer/Epoxy based adhesive as per

adhesive chart and substrate and per directions of Engineer in‐charge. Grouting should be done

using filling and pointing method as per installation drawing provided, and colour of the grout

should be as per the architect’s specification depending on the substrate and as per the direction

of Engineer in‐charge.

49 External (AAC Block)

Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry 100 mm/ 125 mm

thick with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3)

6.38 in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 cum 104.02 10195.45 10,60,566.39

coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at

every third course of masonry work.

50 Glass panel

Design supply & installation of suspended Spider Glazing system designed to withstand the

wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-

316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear

toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with

laminated glass fins 21 mm thick. The Glass finsand glass panel assembly shall be connected to

Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the

bottom using SS channel of 50 x 25 x 2 mm using fastener & anchor bolts, non staining

weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic

contacts, all complete to perform as per specification and approved drawings. The complete

system to be designed to accommodate thermal expansion & seismic movements etc. The

joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the

assembly to be filled with non staining weather sealant, so as to make the entire system fully

water proof & dust proof. The rate shall include all design, Engineering and shop drawing

including approval from structural designer, labour, T&P, scaffolding, other incidental charges

including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer

plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of

payment, actual elevation area of Glazing including thickness of joints and the portion of Glass

panel inside the SS channel shall be measured.

51 Terracotta tiles

26.92.2 With 16 mm thickness (+/- 10%) terracotta tiles of other than grey colors. sqm 7.56 5991.40 45,294.98

Providing and applying white cement based putty of average thickness 1 mm, of approved

13.80 brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth sqm 9654.13 156.05 15,06,526.83

With water thinnable cement primer on wall surface having VOC content less than 50

grams/litre: (DSR 2023 item no. 13.85.3 P-206.)

54 Water proofing

Finishing walls with water proofing cement paint of required shade: (DSR 2023 item no.

55 Acrylic emulsion paint

Finishing walls with ready mixed Premium acrylic emulsion paint (Company Depot Tinted) having

VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt

resistance exterior paint of required shade with silicon additives. (DSR 2023 item no. 13.48A P-

Supply of " ROOM NAMES " Materialtype 1. SS 316 Grade 1mm Thickness Brush Finish 2.

56 MR Laser Cut 3.Chemical Etching 4. Asian Enamel Paint as per Design 5. Bl:ack Colur Letter 6. no. 19.00 906.24 17,218.56

Size: 400mm X 80 mm (16" X 4" inches)

Supply of " FIRE COMMAND ROOM " Materialtype 1.2mm Rigid Sheet 2.Photo

57 MR Luminescent 3. HP latex Printing With Lamination 4. Single Side 5. Size: 400mm X 80 mm no. 1.00 906.24 906.24

(16" X 4" inches)

Supply of " ENTRANCE " Materialtype 1. SS 316 Grade 1mm Thickness Brush Finish 2.

58 MR Laser Cut 3.Chemical Etching 4. Asian Enamel Paint as per Design 5. Bl:ack Colur Letter 6. no. 3.00 2039.04 6,117.12

Size: 600mm X 150 mm ( 24" X 6" inches)

Supply of " TOILET & LIFT " Materialtype 1. SS 316 Grade 1mm Thickness Brush Finish 2.

59 MR Laser Cut 3.Chemical Etching 4. Asian Enamel Paint as per Design 5. Bl:ack Colur Letter 6. no. 4.00 792.96 3,171.84

Size: 200mm X 170 mm ( 7" X 8" inches)

Supply of " ROOM NUMBERS " Materialtype 1. SS 316 Grade 1mm Thickness Brush Finish

60 MR 2. Laser Cut 3.Chemical Etching 4. Asian Enamel Paint as per Design 5. Bl:ack Colur Letter 6. no. 2.00 254.88 509.76

Size: 75mm X 150 mm ( 6" X 3" inches)

Supply of " STAIR CASE " Materialtype 1. SS 316 Grade 1mm Thickness Brush Finish 2.

61 MR Laser Cut 3.Chemical Etching 4. Asian Enamel Paint as per Design 5. Bl:ack Colur Letter 6. no. 3.00 1274.40 3,823.20

Size: 245mm X 230 mm ( 10" X 9" inches)

Supply of " LIFT " Materialtype 1. SS 316 Grade 1mm Thickness Brush Finish 2. Laser Cut

62 MR 3.Chemical Etching 4. Asian Enamel Paint as per Design 5. Bl:ack Colur Letter 6. Size: no. 6.00 2718.72 16,312.32

600mm X 200 mm ( 24" X 8" inches)

Supply of " FIRE EXIT" Materialtype 1. 2mm Rigid Sheet 2.Photo Luminescent 3. HP latex

Printing With Lamination 4. Single Side 5. Size: 260mm X 105 mm ( 10" X 4" inches)

Supply of " IN CASE OF FIRE " Materialtype 1. 2mm Rigid Sheet 2.Photo Luminescent 3. HP

latex Printing With Lamination 4. Single Side 5. Size: 185mm X 210 mm ( 7" X 8" inches)

Supply of " FLOOR INDICATOR " Materialtype 1. 2mm Rigid Sheet 2.Photo Luminescent 3.

HP latex Printing With Lamination 4. Single Side 5. Size: 185mm X 210 mm ( 7" X 8" inches)

Supply of " MCP " Materialtype 1. 2mm Rigid Sheet 2.Photo Luminescent 3. HP latex Printing

With Lamination 4. Single Side 5. Size: 185mm X 210 mm ( 7" X 8" inches)

Supply of " FIRE EXTINGUISHERS " Materialtype 1. 2mm Rigid Sheet 2.Photo Luminescent

67 MR 3. HP latex Printing With Lamination 4. Single Side 5. Size: 185mm X 210 mm ( 7" X 8" no. 17.00 198.24 3,370.08

Supply of " ACTION BY SECURITY & FIRE ORDER " Materialtype 1.2mm Rigid Sheet

68 MR 2.Vinyl Sticker 3. HP latex Printing With Lamination 4. Single Side 5. Size: 600mm X 1200 no. 7.00 4078.08 28,546.56

mm ( 24" X 48" inches)

Supply of " ASSEMBLY POINT " Materialtype 1. 3mm ACP Board 2.Photo Luminescent 3.

69 MR HP latex Printing With Lamination 4. Single Side 5. Size: 600mm X 600 mm ( 24" X 24" no. 1.00 2039.04 2,039.04

Supply of " ASSEMBLY POINT " Materialtype 1. 3mm ACP Board 2.Photo Luminescent 3.

70 MR HP latex Printing With Lamination 4. Single Side 5. Size: 600mm X 600 mm ( 24" X 24" no. 9.00 958.16 8,623.44

Supply of " PLUMBING SHAFT/ FIRE HOSE REEL/ FIRE SHAFT " Materialtype 1. 2mm

71 MR Rigid Sheet 2.Photo Luminescent 3. HP latex Printing With Lamination 4. Single Side 5.Size: no. 7.00 141.60 991.20

Specification: 6 ft Nizarna (Standing) Maa Saraswati Statue Providing, fabricating, and

installing a 6 ft Nizarna statue of Maa Saraswati including pedestal, internal support, finishing,

and complete installation at site.

•Primary Material: Natural stone (Marble / Sandstone / Granite) as approved.

•Quality: Free from cracks, veins, and discoloration; durable for indoor or outdoor installation.

•Finish: Polished, honed as per design approval.

•Height: 6 ft (approx. 1.83 m) from base to crown

•Width/Depth: Proportional to height (approx. 1–1.5 ft width, 2–2.5 ft depth)

•Base/Pedestal: 1–1.5 ft high, reinforced for structural stability

Structural Support:

•Internal mild steel or stainless-steel rod/frame for stability

•Anchoring provisions to secure statue on pedestal

•Designed to withstand total weight and external forces.

Design & Craftsmanship:

•Nizarna (standing) posture holding Veena and traditional attributes (books, lotus)

•Classical attire, jewelry, and ornaments carved or cast in detail

•Smooth finishing with no sharp edges; facial features serene and proportionate

•Iconography to follow traditional Shilpa Shastra guidelines

•RCC pedestal prepared to carry statue weight

•Anchoring using MS/SS bolts or dowels

•Alignment, plumb, and level checked with laser/plumb line

•Temporary supports and protective measures during installation

•All materials, labour, transport, fabrication, installation, scaffolding, protective coatings, and TOTAL:- 10,08,22,359.59 1,43,26,344.19

Estimate for the Work :- ICAI BHAWAN BUILDING, RAIPUR. (PH Works)

Unit Rate Amount

Sl No. DSR Item Code Description Unit Qty MARKET

DSR 2023 DSR 2023 MARKET RATE

A- Internal Sanitary & Plumbing System

1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply and all CPVC plain & brass threaded fittings,

including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent cement and testing of joints complete as

per direction of Engineer in Charge.

Internal work - Exposed on wall

ITEM NO-18.7.2 20mm dia C-PVC pipe Mtr 120 335.00 48,186.00

ITEM NO-18.7.3 25mm dia C-PVC pipe Mtr 120 401.55 48,186.00

ITEM NO-18.7.4 32mm dia C-PVC pipe Mtr 130 518.75 67,438.00

ITEM NO-18.7.5 40mm dia C-PVC pipe Mtr 120 702.95 84,354.00

ITEM NO-18.7.6 50mm dia C-PVC pipe Mtr 120 934.15 1,12,098.00

2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded

fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent cement and the cost of cutting chases

and making good the same including testing of joints complete as per direction of

Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

ITEM NO-18.8.2 20mm dia C-PVC pipe Mtr 120 537.60 64,512.00

ITEM NO-18.8.3 25mm dia C-PVC pipe Mtr 110 627.25 68,998.00

ITEM NO-18.8.4 32mm dia C-PVC pipe Mtr 90 739.30 66,537.00

3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply including all CPVC plain & brass threaded

fittings This includes jointing of pipes & fittings with one

step CPVC solvent cement, trenching, refilling & testing of joints complete as per

direction of Engineer in Charge.

ITEM NO-18.9.5 40mm dia C-PVC pipe Mtr 40 563.05 22,522.00

ITEM NO-18.9.6 50mm dia C-PVC pipe Mtr 50 794.25 39,713.00

ITEM NO-18.9.7 65mm dia C-PVC pipe Mtr 45 1674.40 75,348.00

4 Supplying all materials, labour, T&P and fitting and fixing PVC SWR soil waste

ventilating pipes and fittings of the following outside diameter conforming to ISI No.

13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches

including jointing with supply of approved rubber lubricant by non-heat application

method/as per manufacturer’s specification, testing, earthwork in excavation in all

kinds of soil and refilling of trenches as per specification and direction of the

Engineer in charge.

ITEM NO- 19.3.1 110mm SWR pipes Mtr 490 458.50 2,24,665.00

5 Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for

unplasticised Rigid PVC pipes conforming to IS: 13592 Type A, including jointing with

seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

MR 110mm PVC 'P' trap Each 40 580.00 23,200.00

ITEM NO-12.42.1.2 110mm PVC socket plain Each 85 136.15 11,573.00

ITEM NO-12.42.5.2 110mm PVC plain bend Each 70 150.35 10,525.00

ITEM NO-12.42.5.2 110mm PVC door bend Each 30 150.35 4,511.00

ITEM NO-12.42.3.2 110mm PVC door Tee Each 25 234.15 5,854.00

MR 110mm PVC plain Tee Each 50 322.70 16,135.00

ITEM NO-12.42.4.2 110mm PVC door cross Tee Each 35 221.35 7,747.00

MR 110mm dia PVC Offset without ear Each 28 407.40 11,407.20

MR 110mm PVC vent cowl Each 35 58.20 2,037.00

MR 110mm PVC Clamp Each 260 42.80 11,128.00

6 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :

5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

7 ITEM NO- 12.44 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm

diameter and weighing not less than 440 grams. Each 12 54.70 656.00

8 MR Matrix Set -1 (WB 65 x 35 with one pair mounting brackets, EWC & Cistern complete

with fittings & seat cover, one no hinged rail 76 cm and five nos of grab rails 60 cm)

9 Supplying all materials,labour,T&P and fitting and fixing vitrous Chaina washed

down water Closet (European type water closet - EWC) with integral "P" or "S" type

trap to the floor including wodden plug and chromoum plated screw including

jointing the trap with soil pipe in CM(1:1) fixing plastic seat cover for washed down

water closet with crmium plated brass hinges and rubber buffers including polishing

etc all complete as per specification and direction of Engineer-in-charge.

European Water Clost "S" trap

10 Supplying all materials, labour, T&P and fitting and fixing 10 litres capacity low level

flushing cistern with a pair of cast iron or M.S brackets complete with fittings such

as siphonic arrangements 15mm nominal size brass/pvc ball valve with polythene

float CP brass handle, unions and couplings for connection with inlet, outlet and

overflow pipes,32mm dia CP flush bend,15mm dia pvc inlet connection pipe

including cutting holes and making good the same and connecting the flush bend

with cistern and closet and connecting the inlet pipe with supply main etc all

complete as per specification and direction of the Engineer in charge.

ITEM NO 17.18.1 10 litres PVC L.L. Cistern (Slimline-white) with flush bend . Each 27 1190.65 32,147.55

11 Supplying all materials ,labour ,T&P and fixing Wash basin with hole for pillar taps

with cast iron or MS brackets painted white including cutting holes in walls and

making good the damages with supply of wooden plugs, screws and cement etc.

fixing pedestral for wash basin recessed at the back for the reception of pipes and

fittings, fixing PVC waste pipe of 32mm nominal diameter for wash basin including

brass check nut complete, fixing pillar taps capstan head screw down high pressure

lettered 'Hot' and 'Cold' with long screws, shanks and back nuts of 15mm dia

nominal bore, fixing15mm dia PVC inlet connection pipe and making connection

with pillar cocks and supply mains for wash basin , fixing 12mm dia CP brass waste

etc.all complete as per specification and direction of Engineer-in-charge.

ITEM NO 17.8 550mmx400mm size wash hand basin with Porcelain pedestal Each 7 1683.35 11,783.00

ITEM NO 17.7.3 560mmx450mm size under counter basin Each 16 2301.75 36,828.00

ITEM NO 17.69 32mm dia PVC waste pipe with brass coupling nut Each 23 115.30 2,652.00

ITEM NO 18.21.1.1 15mm dia PVC inlet connection pipe 0.45m long Each 23 85.00 1,955.00

12 Supplying all materials,labour,T&P and Bowl pattern urinal of the following sizes

including connecting the urinal with 32mm dia PVC waste pipe 910mm long by

means of white lead mixed with chopped hemp, fixing 32mm dia cp dome

west,15mm dia cp spreader including cutting holes in wall and making good the

damages with supply of wooden plugs,screws and cement etc. all complete as per

specification and direction of the Engineer-in-charge.

580x380x350 mm half stall urinal with 5 litre P.V.C. automatic flushing cistern

ITEM NO 17.75 Cost of 15mm dia urinal spreader Each 10 107.20 1,072.00

ITEM NO17.28.2.1 32mm dia CP dome waste Each 10 119.55 1,196.00

ITEM NO 18.7.1 15mm dia PVC inlet connection pipe 450 Mm Polyamid Braided Hose 12 mm Each 10 286.80 2,868.00

13 Supplying all materials, labour, T&P and fixing Cera Quatrino 24x18 inch Stainless

Steel Single Bowl Kitchen Sink, Matt Finish, Top Mount, 1.0 mm Thick, Grade: 304

including fitting and fixing a pair of cast iron or MS brackets painted white, fixing

50mm/40mm dia ss waste, fixing 50mm/40mm dia PVC waste pipe 910mm long

with supply of wooden plugs, screws and cement etc including cutting holes in walls

and making good the damages etc all complete as per specification and direction of

the Engineer in charge.

ITEM NO 17.9.1 (610x457x250 mm) stainless Steel kitchen sink Each 2 3892.75 7,786.00

14 Supplying all materials, labour, T&P, fitting and fixing brass/CP fittings of the

following nominal bore with supply of all jointing materials complete as per

specification and direction of the EIC.

ITEM NO -18.49.1 15mm dia CP 2way bib cock Each 27 506.80 13,684.00

ITEM NO-17.16A 15mm dia CP Health faucet Each 27 349.15 9,427.00

ITEM NO-18.63 15mm dia CP Angle stop cock Each 56 156.90 8,786.00

ITEM NO -18.15.1 15mm dia CP Abulation Tap Each 2 353.25 707.00

MR 15mm dia CP Sink cock with regular swinging spout with wall flange Each 2 1520.00 3,040.00

ITEM NO-17.7.4 15mm dia Pillar cock Each 23 1879.20 43,222.00

ITEM NO-18.53A 15mm dia CP extension piece Each 60 74.80 4,488.00

ITEM NO-18.74.1 PVC Connection Pipe Each 50 96.35 4,818.00

ITEM NO-17.28.1.1 32mm PVC Waste Discharge Pipe Each 33 103.90 3,429.00

ITEM NO-18.53A 15mm dia. C.P flange Each 85 74.80 6,358.00

ITEM NO-10.25.2 125mm dia CP gratting Each 52 172.60 8,975.00

15 Supplying all materials,labour,T&P and fixing standard sized Glass-shelf, Towel Rail,

Towel Ring, Soap Holder, Soap dispenser with C.P brass bracket and guard rail

complete fixed to wooden pluges with screw etc.all complete as per specification

and direction of Engineer-in-charge.

ITEM NO-17.33 600mmx125mm size glass shelf with C.P ruard Rail. Each 7 1083.50 7,585.00

ITEM NO-17.72 CP Towel Ring. Each 18 231.95 4,175.00

ITEM NO-18.65 C P soap Holder. Each 6 111.45 669.00

ITEM NO-17.71 C P Soap Dispenser.

ITEM NO-17.34.1 C P Toilet Roll Holder. Each 25 803.70 20,093.00

MR Bolt touch-free infrared hand dryer with 1150W rated power & carbon brush motor.

16 Supplying all materials ,labour ,T&P and fixing Mirror of superior glass mounted on

6mm thick A.C. sheet or ply wood sheet and fixed to wooden plugs with chromium

plated brass screws and washers etc.all complete as per specification and direction

of Engineer-in-charge.

ITEM NO - 17.31 Single Mirror 600mmx450mm Each 23 1607.95 36,983.00

17 Supplying all materials, labour, T&P and fitting and fixing G.M/ Brass fittings of the

following nominal bore with supply of all jointing materials complete as per

specification and direction of the Engineer in charge.

ITEM NO - 18.17.1 25mm dia Brass F.W valve Each 30 622.40 18,672.00

ITEM NO - 18.17.2 32mm dia Brass F.W valve Each 22 689.60 15,171.00

ITEM NO - 18.18.3 25mm dia CPVC Ball valve Each 28 464.05 12,993.00

18 MR Supplying all materials, labour, T&P and providing fitting and fixing Aquaguard PRO

Thermapure 120 PSS RO ACH which gives you Hot,Cold & Ambient purified

water.Aquaguard PEO Thermapure 120 PSS RO has built-in-3 stage

combinations,Tank Capacity 120Ltr.,Cold Water-80 Ltrs,Hot water-20 Ltrs.,Ambient

water-2- Ltrs.,Cooling capacity-60 LPH,Refrigerant-HFC R134a,Cold water

temperature-15 Deg.C+/-1*,Heating coil wattage-2000W,Hot water temperature-50

Deg C+/-1,Thermal insulation-PUF,No of Faucets-1 Hot,1 Cold,1 Ambient,Tank,front

panel and drain tray MOC-SS304,Other body panels-Powder coated CRCA Steel,No

of filtration stages-7,RO Capacity-50 LPH*,RORecovery%-50%*,TDS Reject-90%*,

Dimentions (WxDxH)cm-75x72x144,Net weight-92 Kg.etc.all complete as per

direction of the Engineer-in-charge.

19 Providing and placing on terrace (at all floor levels) polyethylene water storage tank,

IS : 12701 marked, with cover and suitable locking arrangement and making

necessary holes for inlet, outlet and overflow pipes but without fittings and the base

support for tank.

ITEM NO - 18.48 Fixing 3 no's of 2000Ltr Roto-moulded water storage tanks-In Terrace floor Per Ltr. 6000 11.00 66,000.00

ITEM NO - 18.48 Fixing 2 no's of 500Ltr Roto-moulded water storage tanks-In Security Shade terrace

B- Construction of 1 Nos of 10000 Liters Fire fighting RCC Over head Tank of Inside

20 Supplying all materials, labour, T&P and providing cement concrete (1:1.5:3) with

M20 hard broken granite chips for R.C.C works including hoisting, laying, watering,

curing, conveyance of all materials to worksite, payment of royalty, taxes etc all

complete as per specification and direction of the Engineer in charge.

21 Supplying all materials, labour, T&P and providing M.S reinforcement for R.C.C work

including cutting, bending, binding, and tying the grills and placing in position

including cost of binding wire 18 to 20 gauge, conveyance of all materials to

worksite, payment of royalty, taxes etc all complete as per specification and

direction of the Engineer in charge.

22 Supplying all materials, labour, T&P and providing rigid and smooth centering and

shuttering for R.C.C works including false work and dismantling them after casting

including conveyance of all materials to worksite, payment of royalty, taxes etc all

complete as per specification and direction of the Engineer in charge.

a ITEM NO - 5.9.3 RCC floor roof, chajja etc sqm 23.36 927.25 21,661.00

b ITEM NO - 5.9.6 RCC Beam, Column, wall etc sqm 61.05 961.30 58,687.00

23 Supplying all materials,labour,T&P and providing 6mm CP (1:4) with cement

punning on brick work including watering,curing,cost of all materials, conveyance of

all materials to worksite,payment of royalty,all taxes etc.all complete as per PWD

ITEM NO - 13.12 specification and direction of the Engineer-in-charge. sqm 32.46 537.45 17,446.00

24 ITEM NO- 13.18 Supplying all materials, labour, T&P and providing cement punning including

watering, curring and conveyance of all materials to site. sqm 32.46 79.95 2,595.00

Quantity same as item No-4

25 ITEM NO -10.25.2 Providing fitting and fixing stainless steel ladder including fixing to wall necessary

welding etc. complete Kg 60.00 172.60 10,356.00

26 ITEM NO -10.25.2 Providing fitting and fixing MS cover made out of MS angle and sheet duly welding

and fixing with frame and hinges along with locking arrangement of size 60cmx60cm

etc complete as per direction of Engineer-in-charge Kg 20.00 172.60 3,452.00

C. External Services

27 ITEM NO -19.4.2 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I.

grating brick masonry chamber with water tight C.I. cover with frame of 300 x 300

mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not

less than 2.70 kg as per standard design Each 7.00 2734.20 19,139.00

150 x 100 mm size P type

28 ITEM NO -19.30.3 Supplying all materials ,labour ,T&P and Constructing brick masonry chamber for

underground C.I. inspection

chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I.

cover with frame (light duty) 455x610 mm internal dimensions, total weight of

cover with frame to be not less than 38 kg (weight of cover

23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5

fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete

1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size),

inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand),

finished smooth with a floating coat of neat cement on walls and bed concrete etc.

complete as per standard design.

Inside dimensions 600x 850 mm and 45 cm deep for pipe

line with three or more inlets Each 8.00 9594.35 76,755.00

29 Supplying all materials ,labour ,T&P and constructing Man Hole Chamber of inside

size 910mmx910mmx910mm with cement concrete (1:3:6) using 40mm size

crusher broken hard black granite metal on bed , KB brick work in cement mortar

(1:6) in foundation and plinth, moulding and shaping the channel inside and

benching with cement concrete (1:2:4) using 12mm size crusher broken hard black

granite chips, 12mm thick cement plaster (1:3) with cement punning to inside,

cement flush pointing (1:3) to outside, R.C.C cover slab (1:2:4) using 12mm size

crusher broken black hard granite chips with R.C.C man hole cover, earth work in

excavation in all kinds of soil and refilling the cavity around the chamber including

watering,curing, conveyance of all materials to worksite, payment of royalty, taxes

etc.all complete as per approved drawing, P.H specification and direction

Inside size : 910mmx910mmx910mm

ITEM NO 19.9.1.1 Circular MH inside dia 900mmx1110mm with sides sloped upto560mm Each 10 12725.00 1,27,250.00

30 Supplying all materials, labour, T&P and making MS step iron in 20mm diameter MS

steel bars and fixing into walls of man hole/septic tank duly embedded in cement

concrete (1:3:6) complete as per specification and direction , DSR 2023 vol-1 item

ITEM NO -10.25.2 Making MS step iron in 20mm diameter MS steel bars Kg 486 172.60 83,884.00

31 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars

jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2

fine sand) including testing of joints etc. complete

ITEM NO -19.6.2 150mm dia Hume pipe- NP-2. Mtr. 170 556.45 94,597.00

ITEM NO -19.6.3 250mm dia Hume Pipe- NP-2. Mtr. 110 899.80 98,978.00

D. Construction of 6.75mx3.60m x 1.40m(h) Rain water Recharge Pit- 2 Nos.

32 Sinking of tube well through D.T.H.Rig.

33 Lowering of PVC casing pipe inside bore.

34 MR Cost.of 200mm dia (Sch.80)Pipe Mtr. 50 1775.60 88,780.00

35 MR Cutting slot in casing pipe for recharge of rain water Mtr. 50 353.50 17,675.00

36 Labour for packing gravel outside the tube well

37 MR Cost of washed gravel. Cum 4.7 1723.50 8,100.45

38 ITEM NO 2.8 & 2.26 Earth work in all kinds of soil within 50 mtr initial lead and 1.5mtr initial lift including 133.38

rough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not

exceeding 0.3 mtr in depth and as per direction of the Engineer in charge.

39 ITEM NO - 4.1.8 Supplying all materials, labour, T&P and providing cement concrete (1:4:8) with 4cm 2.16

size hard granite metal including watering, curing, conveyance of all materials to

worksite, payment of royalty, taxes etc all complete as per specification and

direction of the Engineer in charge. Cum 6812.00 14,745.00

6.4 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation

7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in

40 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 22.8 9105.95 1,99,558.00

41 13.1.1 Supplying all materials, labour, T&P and providing 12mm thick cement plaster (1:4) 182.4

on brickwork including watering, curing, conveyance of all materials to worksite,

payment of royalty, taxes etc all complete as per specification and direction of the

Engineer in charge. Sqm 347.05 63,302.00

42 ITEM NO -13.18 Supplying all materials, labour, T&P and providing cement punning including 97.2

watering, curing, conveyance of all materials to worksite, payment of royalty, taxes

etc all complete as per specification and direction of the Engineer in charge.

43 ITEM NO - 5.9.3 Supplying all materials, labour, T&P and providing rigid and smooth centering and 6.26

shuttering for R.C.C works including false work and dismantling them after casting

including conveyance of all materials to worksite, payment of royalty, taxes etc all

complete as per specification and direction of the Engineer in charge.

44 ITEM NO - 4.20.1.4 Supplying all materials, labour, T&P and providing reinforced cement concrete work 0.84

of M-25 grade with 20mm and down grade black hard granite crusher broken stone

chips including hoisting, laying, watering, curing, conveyance of all materials to

worksite, payment of royalty, taxes etc all complete as per specification and

direction of the Engineer in charge. Cum 9439.05 7,929.00

45 ITEM NO - 5.22.6 Steel reinforcement (Fe-500D) for R.C.C. work including straightening, cutting,

bending, placing in position and binding all complete upto plinth level.

46 Providing and filling filter media

b ITEM NO - 0295 20mm size washed gravel-2x6.0x2.50x0.40=12 Cum 12.00 1425.00 17,100.00

47 ITEM NO - 10.25.2 Providing fitting and fixing M.S.grill, Jalli cover over the harvesty pindi. Qntl. 4.00 172.60 690.00

E. Sinking of 200mm x 150mm Large Tube well through DTH method - 2Nos.

48 MR Labour for drilling a perfectly vertical bore hole of specified dia for a specified depth

below ground level through consolidated and unconsolidated rock with down the

hole hammer drilling rig or combination rig as required to suit the site condition as

per the direction of the Engineer in charge including use of own rig with its

accessories, tools and plant and consumables etc for lowering of 200mm/150mm

dia G.I/P.V.C/M.S casing pipes for housing fitted with socket and with or without

well screen as per the necessity for soft, medium, hard and boulder

formation(G.I/P.V.C/M.S casing pipes if required to prevent collapse of overburden

is to be provided by the contractor including lowering and withdrawing after

completion of the tube well), 200mm dia to 400mm dia in overburden portion

including packing of gravel supplied by the contractor for 400mm dia bore only .

Drilling of 200mm dia bore 0 to 30 mtr (2x30mtr)

49 MR Drilling of 200mm dia bore 31 to 45 mtr (2x15mtr) mtr 30 1113.35 33,400.50

50 MR Drilling of 150mm dia bore 45 to 100 mtr (2x55mtr) mtr 110 1113.35 1,22,468.50

51 MR Labour for lowering the following size of PVC casing pipes with or without slotted

pipes as per necessity from ground level upto 300 mtrs depth and fitted and set up

in perfectly vertical position including cutting and threading of blank pipes and

slotted pipes and supplyinging and fixing of all jointing materials ,extra sockets and

T&P etc. all complete and keeping the top of casing pipe threaded including plugging

the tubewell to prevent entry of foreign materials.

Lowering of 200mm dia PVC casing pipes 0 mtr to 30 mtrs (2x30mtr)

52 MR Lowering of 200mm dia PVC casing pipes 31 mtr to 45 mtrs (2x15mtr) mtr 30 180.50 5,415.00

53 MR Cost of 200mm dia PVC schedule - 80 pipe (2x46mtr) mtr 92 1941.45 1,78,613.40

54 MR Cleaning and developing the tube well with supply of compressor worked till clear

and adequate discharge is obtained from the tube well including supply and use of

all necessary equipment and labour as per direction of the Engineer in charge .

55 MR Supplying all materials, labour, tools and plant and withdrawing casing pipes from

the unsuccessful bore and depositing in the departmental store in good condition.

Labour for withdrawing of 200 mm dia PVC/GI Casing Pipe

56 MR Supplying all materials,labour,T&P and providing around sealing by cement

concrete grouting of annualr space around GI/PVC housing pipe upto 5 mtr below

ground level ( as per drawing ) to plug the bore hole excluding cost of cement all

complete as per direction of the Engineer-in-charge . Mimimum one meter of casing

pipe to nserted in the bore in to the rock the bottom to ensure sanitary sealing (

excluding cost of cement which willbe supplied by the Department ) .

CC(1:2:4) with 12mm chips for grouting up to 5 mtr Depth in

Installation of 2 HP submerssible pump-motor

57 MR Supplying all materials, labour, T&P and providing fitting & fixing submerssible pump

with squirrel cage induction type submerssible electric motor to run single-phase

line voltage ranging from320 to450 volt confirm to IS 8034/89 with following

specification suitable control pannel jointing with GI/PVC/HDPE pipe, electrification,

testing, commissioning , trial running, conveyance of all material to work site,

payment of all taxces etc all complete as per PH specification and direction of

Engineer-in-charge.

KS4HF-2010 2H.P three phase 10 stage head range 30 to 54 metres, discharge 155

to 110 L.P.M with outlet dia of 32m. each 3 16625.60 49,876.80

58 MR DOL contol pannel each 3 3805.50 11,416.50

59 MR 2.50 sqmm flate cable mtr 250 128.10 32,025.00

60 MR 40mm dia steel short piece each 6 202.00 1,212.00

61 MR Steel rope with cover mtr 100 26.70 2,670.00

62 MR Well cap each 2 152.30 304.60

63 MR 50mm size CI bracket each 6 91.30 547.80

64 MR 20mm dia rigid U-PVC pipe mtr 160 6.90 1,104.00

65 MR Supplying all materials, labour, T & P and providing & electrification to submerssible

pump sets ane service connection including fitting fixing of electric board & Switch

etc all complete as per direction of Engineer-in-charge.

66 MR Supplying all materials , labour, T&P and providing and fixing to wall or ceiling and

floor PVC pipes conforming to ASTM-D-1785/89 ( Sch-80 ) and G.I pipe fittings of the

following nominal bore with clamps including making good the wall,ceiling and floor

,testing all complete as per P.H. specification and direction of Engineer-in-charge .

In ground floor

40mm dia UPVC ASTM-D Pipes

67 MR Supplying all materials, labour, T&P and constructing Bore well protection chamber

of the inside size 650x650x1000hight with cement concrete (1:3:6) using 40mm size

hard granite metal on foundation, 1st class Fly ash brickwork in cement mortar

(1:3), with base cement concrete (1:2:4) using 12mm size h.g chips,12mmthick

cement plaster (1:4) inside and outside, R.C.C cover slab in (1:1.5:3) using 12mm

size h.g chips, earthwork in excavation in all kinds of soil and refilling the cavity

around the chamber including watering, curing, conveyance of all materials to

worksite, payment of royalty, taxes etc all complete as per approved specification

and direction of the Engineer in charge.

Bore well chamber

F. Construction of 100KLD RCC Fire fighting Under ground Reserver of Inside size-

68 ITEM NO - 2.8 & 2.26 Earth work in All kinds of soil and gravels mixed with stone and boulder not

exceeding 0.014 Cum in volume within 50m initiallead and 1.5 m initial lift including

rough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not

exceeding 0.30m in depth and as per specification approved by the Department.

69 -do- with Ist additional depth of 1.50 m over the initial lead and lift.

70 ITEM NO - 2.27 Supplying all materials, labour, T&P and filling in foundation and plinth with sand

well watered and rammed including conveyance of all materials to worksite,

payment of royalty, taxes etc.all complete as per direction of the Engineer in

71 ITEM NO - 4.1.8 Supplying all materials, labour, T&P and providing cement concrete (1:4:8) with 4cm

size hard granite metal including watering, curing, conveyance of all materials to

worksite, payment of royalty, taxes etc all complete as per specification and

direction of the Engineer in charge.

72 ITEM NO - 5.19A Supplying all materials, labour, T&P and providing cement concrete (1:2:4) with

M25 hard broken granite chips for R.C.C works including hoisting, laying, watering,

curing, conveyance of all materials to worksite, payment of royalty, taxes etc all

complete as per specification and direction of the Engineer in charge.

Base slab -1x10.90x6.40x0.30=

73 ITEM NO - 5.22.6 Supplying all materials, labour, T&P and providing M.S.Reinforcement for RCC work

including cutting, banding, binding, straightening and trying the grills and placing in

position including cost of binding wire 18 to 20 gage.

74 ITEM NO -5.9.1 Supplying all materials, labour, T&P and providing rigid and smooth centering and

shuttering for RCC work including false work and dismantling then after casting

including cost of materials complete in ground floor.

75 ITEM NO -5.9 RCC Beam, Column, wall etc

76 ITEM NO -5.9 RCC Plinth bend/ Raft

77 ITEM NO -13.16 Supplying all materials, labour,T&P and providing 6mm thick cement plasster (1:3)

over CC work including watering curring and conveyance of all materials to site.

Bottom - 1x10.00x5.50=

78 ITEM NO 4.1.8 Supplying all materials, labour, T&P and providing cement punning including

watering, curring and conveyance of all materials to site.

Quantity same as item No-4 Sqm 13.95 79.95 1,115.00

79 ITEM NO 10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,

channels, plates etc., including welding, grinding, buffing, polishing and making

curvature (wherever required) and fitting the same with necessary stainless steel

nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless

steel dash fasteners , stainless steel bolts etc., of required size, on the top of the

floor or the side of waistslab with suitable arrangement as per approval of Engineer-

in-charge, (for payment purpose only weight of stainless steel members shall be

considered excluding fixing accessories such as nuts, bolts, fasteners etc.).DSR 2023

Item no-10.28, P-173.

80 MR Providing fitting and fixing RCPC cover etc complete as per direction of Engineer-in-

81 ITEM NO 5.9.6 Supplying all materials, labour, T&P and providing shoring and shuttering foundation

trenches, pits etc with close wooden planks or sheets shuttering etc all complete as

per direction of the Engineer in charge.

82 MR De-watering

10 daysx 2hours x 5.0 HP pump HP-Hr 100 59.00 5,900.00

G. Construction of 15KLD RCC Domestic Under ground Reserver of Inside size-

ITEM NO 2.8 & 2.26 Earthwork in excavation of foundation in all kinds of soil within 50m initial lead and

1.5m initial lift including rough dressing and breaking clods to minimum 5cm to 7cm

and laying in layers not exceeding 0.30m in depth and as per direction of the

Engineer in charge. Cum 18.38 260.3 4,783.00

Initial lift - 1 x 3.5 x3.50x 1.50 =

Earthwork in excavation of foundation in stonety earth mixed with gravel within

50m initial lead and 1.5m initial lift including rough dressing and breaking clods to

84 ITEM NO - 2.26

minimum 5cm to 7cm and laying in layers not exceeding 0.30m in depth and as per

direction of the Engineer in charge. Cum 8.58 126.8 1087.00

1st Extra lift - 1 x 3.5 x3.50x 0.70 =

Supplying all materials, labour, T&P and providing filling sand including watering,

85 ITEM NO. - 2.27

ramming and conveyance of all materials to site. Cum 10.21 79.95 816.00

ITEM NO - 4.1.8 Supplying all materials, labour, T&P and providing cement concrete (1:4:8) with 4cm Cum

size hard granite metal including watering, curing, conveyance of all materials to

worksite, payment of royalty, taxes etc all complete as per specification and

direction of the Engineer in charge. 1.26 6812 8593.00

Supplying all materials, labour, T&P and providing cement concrete (1:2:4) with

M25 hard broken granite chips for R.C.C works including hoisting, laying, watering,

87 curing, conveyance of all materials to worksite, payment of royalty, taxes etc all

complete as per specification and direction of the Engineer in charge.

ITEM NO - 5.22.6 Supplying all materials, labour, T&P and providing M.S.Reinforcement for RCC work Kg 107.85

88 including cutting, banding, binding, straightening and trying the grills and placing in

position including cost of binding wire 18 to 20 gage. 520.08 56,091.00

Supplying all materials, labour, T&P and providing rigid and smooth centering and sqm. 842.5

89 shuttering for RCC work including false work and dismantling then after casting

ITEM NO - 5.9.2 including cost of materials complete in ground floor. 11.31 9,530.00

Supplying all materials,labour,T&P and providing 6mm CP (1:4) with cement sqm. 518.55

punning on brick work including watering,curing,cost of all materials, conveyance of

all materials to worksite,payment of royalty,all taxes etc.all complete as per PWD

ITEM NO - 13.11 specification and direction of the Engineer-in-charge. 47.08 24,413.00

Supplying all materials, labour, T&P and providing cement punning including sqm. 79.95

91 ITEM NO -13.18

watering, curring and conveyance of all materials to site. 24.20 1,935.00

Supplying all materials, labour, T&P and futting and fixing 20mm dia MS/CI step iron mtr 10 172.6

92 ITEM NO - 10.25.2 including supply of necessary C.C(1:2:4) for fixing etc complete as per P.H.D.

specification. 1,726.00

Supplying all materials, labour, T&P and cleaning of debries,uprooging and cum 10 17.6

93 ITEM NO - 2.31 disposing at a safe distance all complete as per direction of the Engineer in charge

Sl No. Items Qty Offer Price Offer Total Item Image

1 Auditorium Chair, Push Back, PU Foam, PU Arm, Fabric 500 10000 5000000

Tapestry, 550(L) X 660(D) X 965(H)

Columbia 2 Sofa

Two Seater Sofa, Wooden Frame, SS Pipe Leg,

Size in mm - 1450(L) X 755(D) X 750(H), Leatherette

Faculty Chair GV 618

3 Chair, PU Arm, Chrome Plated Pipe Stand, Seat & Back 18 7350 132300

Fabric Tapestry

Galaxy Centre Table

Centre Table, SS Pipe Frame Chrome Finish, PLPB Edge

Banded Top, 18mm Thick, Marino 10858 Colour

Size 1200 x 600

Lobby Area 0 0

Columbia 3 Sofa

Three Seater Sofa, Wooden Frame, SS Pipe Leg,

Size in mm - 1920(L) X 755(D) X 750(H), Leatherette

Columbia 2 Sofa

Two Seater Sofa, Wooden Frame, SS Pipe Leg,

Size in mm - 1450(L) X 755(D) X 750(H), Leatherette

Columbia 1 Sofa

3 Single Seater Sofa, Wooden Frame, SS Pipe Leg, 2 18700 37400

Size in mm - 865(L) X 755(D) X 750(H), Leatherette Tapestry

Galaxy Centre Table

Centre Table, SS Pipe Frame Chrome Finish, PLPB Edge

Banded Top, 18mm Thick, Marino 10858 Colour

Size 1200 x 600

Galaxy Corner Table

SS Pipe Frame Chrome Finish, PLPB Edge

Banded Top, 18mm Thick, Marino 10858 Colour

FIRST FLOOR 0 0

MCS Room 1 0 0

Student 14 Desk with Chairs

Desk Size W1200 X D400 X H750

2 Seater Student Table With Chair, 2 Side Post Forming

Top, Perforated Metal Modesty And Book Storage, Powder

Coated Pipe Frame

Faculty Table Classic 15 (1200 x 600 x 750)

2 Table, Particle Board Top, Fixed Metal Pedestal, 1 22200 22200

Metal Frame, Powder Coated

Faculty Chair GV 618

3 Chair, PU Arm, Chrome Plated Pipe Stand, Seat & Back 1 7350 7350

Fabric Tapestry

MCS Room 2 0 0

Student 14 Desk with Chairs

Desk Size W1200 X D400 X H750

2 Faculty Table Classic 15 (1200 x 600 x 750) 1 22200 22200

3 Faculty Chair GV 618 1 7350 7350

Faculty Room 0 0

Faculty Table Numero 10 (1350 x 600 x 750)

Table, Particle Board Top, MS Powder Coated Legs

Faculty Chair GA 569

Medium Back Chair, PP Arm, Gas Lift, Nylon Base, Seat &

Mesh Tapestry, Synchro Tilt

Office Bearer 0 0

Numero 7 Table (1200 x 600 x 750)

Executive Table, Particle Board Top

2 Low Back Chair, Pipe PP Arm, PU Moulded Seat & Back, Gas 1 8550 8550

Lift, Nylon Base, Fabric Tapestry, Swivel Tilt

Visitor Chair GB 414

3 Chair, Pipe PP Arm, PU Moulded Seat & Back, Powder 2 6650 13300

Coated Pipe Stand, Fabric Tapestry, Powder Coated

Branch Admin 0 0

Numero 6 Table (1800 x 1650 x 750)

Executive Table, Particle Board Top

Storage 9 (1500 x 450 x 750)

Wooden Storage, Particle Board Structure

Medium Back Chair, PP Arm, Gas Lift, Nylon Base, Seat &

Mesh Tapestry, Synchro Tilt

Visitor Chair GA 551 A

Visitor Chair, PP Arm, Powder Coated Pipe Frame, Mesh

& Seat Fabric Tapestry

Numero 8 Table (1500 x 1650 x 750)

Executive Table, Particle Board Top

Medium Back Chair, PP Arm, Gas Lift, Nylon Base, Seat &

Mesh Tapestry, Synchro Tilt

Conference Room 0 0

Conference 10 Model Table (3000 x 1200 x 750)

Conference Table, Particle Board Edge Banded Top

Conference Chair GM 247

2 Medium Back Chair, PP Arm, Gas Lift, Chrome Base, 10 10600 106000

Leatherette Tapestry, Swivel tilt

Committee Room 0 0

Conference 5 Model Table (4200 x 1500 x 750)

1 Conference Table, Particle board and MDF top, 1 91700 91700

(Without Flip-Up Box)

High Back Chair, PP Arms, Gas Lift, Chrome Base,

Tapestry, Swivel Tilt

Chairman Office 0 0

Accent 1 Desk 2400 x 2000 x 750

Office Table, MDF Top 25mm Thick With Veneer Polish &

Main Chair GP 138 A

2 High Back Chair, Silver PP Cushion Arms, Gas Lift, Silver PP 1 15000 15000

Base, Leatherette Tapestry, Swivel Tilt

Visitor Chair GP 139 A

3 Medium Back Chair, Silver PP Cushion Arms, Gas Lift, Silver 3 14000 42000

PP Base, Leatherette Tapestry, Swivel Tilt

Diplomat 3 Sofa

3 Seater Sofa With Wooden Frame, Wooden Leg,

Size in mm - 2155 (L) X 840 (D) X 760 (H), Leatherette

Diplomat 2 Sofa

2 Seater Sofa With Wooden Frame, Wooden Leg,

Size in mm - 1500 (L) X 840 (D) X 760 (H), Leatherette

Orbit Centre Table

Centre Table, SS Pipe Frame Chrome Finish, PLPB Edge

Banded Top, 18mm Thick, Marino 10858 Colour, 1200 x

Rest Room 0 0

Hostel 9 model Single Bed

1 Single Bed, Wooden Ply, CRCA Pipe Frame, Powder Coated, 3 16400 49200

PPCP shoes, Without Mattress, Size L 2050 X W 965 X H 835

SECOND FLOOR 0 0

Multipurpose Hall 0 0

Without arm, Chrome Plated Pipe Frame,

Stackable, PP Back, Seat Leatherette Tapestry, Chrome

Computer Lab 0 0

Customized Numero 10 Table with Wire Manager of Size

Study/Computer Table, Particle Board Top, MS Powder

Medium Back Chair, PP Fixed Arm, Push back, PU Moulded

Seat & Back, PP Back Cover, Gas Lift, Nylon Base, PVC

Beading, Fabric Tapestry

GENERAL ABSTRACT

NAME OF THE WORK :- ICAI BHAWAN, RAIPUR

SL.No. Description of Item DSR 2023 DSR 2025 Non-DSR

i Paved Road = 3459102.23 -

ii 2 no of Gate with Security Room = 2717665.20 25,11,504.00

iii. Boundary Wall = 5283783.99 -

iv. landscape = 742883

ABSTRACT ESTIMATE FOR CONSTRUCTION OF PAVED ROAD

DSR 2023/ Non-DSR Non-DSR

Sl. No. Item of Work Unit Quantity DSR RATE DSR Amount

Market price RATE Amount

1 Granular subbase

Construction of granular sub-base by providing close graded Material

conforming to specifications, mixing in a mechanical mix plant at OMC, carriage

of mixed material by tippers to work site, for all leads & lifts, spreading in

uniform layers of specified thickness with motor grader on prepared surface

and compacting with vibratory power roller to achieve the desired density,

complete as per specifications and directions of Engineerin-Charge.With

material conforming to Grade-III (size range 26.5 mm to 0.075 mm ) having CBR

Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150

mm thick sub grade of compacted bed of 20 mm thick nominal size stone

11.45 aggregate and base course and filling with 150 mm thick Jamuna sand, sqm 418.15 1708.10 7,14,237.75

including spreading, well ramming, consolidating and finishing smooth etc. all

comp per direction of Engineer-in-charge.

3 Sand filling

Supplying and filling in plinth with sand under floors, including watering,

ramming, consolidating and dressing complete.

Providing and laying factory made chamfered edge Cement Concrete

paver blocks in footpath, parks, lawns, drive ways or light traffic

parking etc, of required strength, thickness & size/ shape, made by

table vibratory method using PU mould, laid in required colour &

pattern over 50mm thick compacted bed of sand, compacting and

proper embedding/laying of inter locking paver blocks into the sand

bedding layer through vibratory compaction by using plate vibrator,

filling the joints with sand and cutting of paver blocks as per required

size and pattern, finishing and sweeping extra sand. complete all as

per direction of Engineer-in-Charge.

80 mm thick C.C. paver block of M-30 grade with approvedcolor design and

5 Pre-cast Kerb Stone

Providing and laying at or near ground level factory made kerb stone of M-25

grade cement concrete in position to the required line, level and curvature,

jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making

joints with or without grooves (thickness of joints except at sharp curve shall

not to more than 5 mm), including making drainage opening wherever required

complete etc. as per direction of Engineerin- charge (length of finished kerb

edging shall be measured to calculate volume for payment). (Precast C.C. kerb

stone shall be approved by Engineer-in-charge).

ABSTRACT ESTIMATE FOR GATE STRUCTURE

Item of Work Unit Quantity DSR RATE Non-DSR RATE DSR Amount Non-DSR Amount

No. Market price

Item no. - 2.8 &

1 Earthwork Excavation

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in

foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including

2.26 dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil

and disposal of surplus excavated soil as directed, within a lead of 50 m.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in

foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan),

including dressing of sides and ramming of bottoms, for all lift, including getting out the

excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m.

2 Sand Filling

Supplying and filling in plinth with sand under floors, including watering, ramming,

consolidating and dressing complete.

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone

aggregate 40 mm nominal size derived from natural sources).

4 Back Filling

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in

layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and

watering, lead up to 50 and for all lift. DSR 2023 vol-1 item no. – 2.25 P-90.

5 Earth Filling

Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical

transport upto a lead of 5km also including ramming and watering of the earth in layers not

exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift.

Providing and laying in position ready mixed or site batched design mix cement concrete for

reinforced cement concrete work (M-25), using coarse aggregate and fine aggregate derived

from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of

concrete, to improve durability and workability without impairingstrength; including pumping

of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering,

shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the

following grades of concrete.

Providing and laying in position ready mixed or site batched design mix cement concrete for

reinforced cement concrete work (M-25), using coarse aggregate and fine aggregate derived

from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of

concrete, to improve durability and workability without impairingstrength; including pumping

of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering,

shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the

following grades of concrete. Cum 13.88 9860.40

7 Steel reinforcement (Fe-500D) for R.C.C. work including straightening, cutting, bending, placing

5.22.6 in position and binding all complete upto plinth level. DSR 2023 item no.5.22.6 P-110. Kg 4088.76 4,40,972.77

Steel reinforcement (Fe-500D) for R.C.C. work including straightening, cutting, bending, placing

5.22A.6 in position and binding all complete upto plinth level. DSR 2023 item no.5.22.6 P-110. Kg 2361.42 2,54,679.15

All shuttering of RCC members shall be as per DSR 2023 Subhead 5. As per Drawings &

Directions of the Engineer in charge.

a. 5.9.1 Foundations, footings, bases of columns, etc. for mass. Sqm 69.60 392.15 27,293.64

b. 5.9.3 Suspended floors, roofs, landings, balconies and access platform. Sqm 20.82 927.25 19,305.35

c. 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. Sqm 73.82 736.40 54,364.36

d. 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 97.02 961.30 93,263.95

Brick work with non modular fly ash bricks conforming to IS:12894, class designation

6.34.2 10 average compressive strength in super structure above plinth level up to floor V cum 10.62 8752.55 92,952.08

Brick work with non modular fly ash bricks conforming to IS:12894, class designation

10 average compressive strength in super structure above plinth level up to floor V cum 0.25 8752.55 2,188.14

13.1.2 12 mm cement plaster of mix. sqm 75.84 333.35 25,281.26

13.2.2 15 mm cement plaster on the rough side of single or half brick wall of mix. sqm 72.18 383.00 27,644.94

13.16.1 6 mm cement plaster of mix. sqm 62.26 300.45 18,706.88

9 Cement concrete flooring 1:2:4

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished

11.3 with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing sqm 13.68 614.2 8,402.26

of steps etc. complete.

10 UPVC Doors Frame

Providing and Fixing factory made uPVC door frame, made of uPVC exturded sections, of size

65 mm x 55 mm with wall thickness 2.0 mm ( ± 0.2 mm), corners of the door frame to be

mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side

vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm

( ± 0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the

frame, fixing the frame with jamb with required number & size of anchor dash fastners, all

complete as per manufacturer’s specification and direction of Engineer-in-charge.

11 UPVC Doors Shutter

35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded

soild PVC profiles, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx

35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side),

having one side thickness of 15 mm integrally extruded on the hinge side of the profile for

better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1

mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self

driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross

9.142.2 section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5 mm thick solid sqm 4.20 4713.05 19,794.81

PVC Lock rail of size 115 mm x 35 mm, out of which 75 mm to be flat and 20 mm to be tapered

at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the

styles & rails with the help of solvent and self driven self tapping screws of 125mm x 11 mm,

including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel,

all complete as per manufacturer’s specification and direction of Engineer-in-charge.

12 WPC DOOR SHUTTER

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) (30 mm

thick) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-

60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat

husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum

density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),

minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance

to spread of flame of Class A category with property of being termite/borer proof,

water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required

size with necessary full body threaded star headed counter sunk S.S screws, all as per direction

of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid

13 WPC DOOR FRAME

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) (Frame

size 50 x 100 mm)solid door/ window/ Clerestory windows & other Frames/ Chowkhat

comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and

natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum

toxicity index of 12 for 100gms) fabricated with miter joints after applying PVC solvent cement

and screwed with full body threaded star headed SS screws having minimum frame density of

26.86.3 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum rmt 9.90 947.70 9,382.23

compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to

spread of flame of Class A category with property of being termite/borer proof,

water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash

fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S

hold fast/lugs or SS dash fasteners shall be paid for separately).

14 UPVC Sliding Windows

Two track two panels sliding door with Aluminium channel for roller track, wool pile,

zinc alloy (zamak) powder coated handle on every panel along with multi-point locking

9.147.B1.2 system, adjustable nylon rollers with SS 304 body. Using R3 series with frame (55 mm sqm 3.60 8106.30 29,182.68

& above) x (40 mm & above) & sash (30 mm & above) x (74 mm & above). (Height upto

15 UPVC Ventilator

Providing and fixing of UPVC (Un Plasticized Poly Vinyl Chloride)(Make: Fenstech) Ventilator

made out of hollow- chambered UPVC Sections having isolated drainage and reinforced

throughout with galvanized steel. The ventilator shall be made out of UPVC sections having an

overall size of 60mm x 60mm thickness. Structurally Reinforced with hot dip galvanized up to

50 microns of minimum thickness of 1.2mm with locking system. Prefabricated & welded

through fusion welding the window outer frame & sash shall be fitted with 5mm thickness Pin-

MR Head glass of reputed brand (Saint Gobain Glass), weathering sealant & Accessories like sqm 0.72 15736.67 11330.40

louvers made by brand. The outer frame is to be installed at the side using anchor fastener,

Silicon Rubber Sealant. At least 15 years manufacturing warranty for discoloration, wrapping,

mechanical failures, Shrinkages, Rooting Corrosion etc. with a quality Certificate from relevant

departments of that government through the Dealers including of all materials and abounds

etc. Complete as per directions of Engineer in-charge

16 M.S. grills

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats,

9.48.1 square or round bars etc. including priming coat with approved steel primer all complete. Kg 2396.64 219.10 5,25,103.82

17 Synthetic Enamel Paint

Painting with synthetic enamel paint of approved brand and manufacture to give an even

18 Acrylic Smooth Exterior Paint

Finishing walls with Acrylic Smooth exterior paint of required shade.New work (Two or more

13.46 coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ Sqm 72.18 160.60 11,592.11

0.90 litre/10 sqm).

19 Acrylic Emulsion Paint

Finishing walls with ready mixed Premium acrylic emulsion paint (Company Depot Tinted)

having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal

resistance, dirt resistance exterior paint of required shade with silicon additives.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to

prepare the surface even and smooth complete.

21 10.2 Structural steel work

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work,

including cutting, hoisting, fixing in position and applying a priming coat of approved steel Kg 2000.00 133.70 2,67,400.00

primer all complete.

22 Market price GFRC WORK

Providing, manufacturing, and installation of Glass Fiber Reinforced Concrete (GFRC) work at

Entry/Exit Gate as per architectural design, pattern, colour, and texture approved by the

Engineer-in-Charge, including all materials, labour, tools & tackles, fixing arrangements, and

complete installation. The GFRC panels/elements shall have a thickness of 25–30 mm and be

installed on/between RCC or blockwork columns or structural steel framework using Dry Fixing

Method with suitable Stainless Steel (SS) pipe & cleats framework, fasteners, and necessary

hardware, complete in all respects.

The GFRC mix shall consist of:

•‘53 Grade’ Ordinary Portland Cement (Make: Birla/JK Cement or equivalent),

•Quartz and Fine Silica Sand,

•Alkali Resistant Glass Fibre (Make: Owens Corning or equivalent),

•Super Plasticizers/Additives (Make: BASF or equivalent),

•Polymers (Make: BASF or equivalent), and

•U.V. Resistant Synthetic Inorganic Pigments (Make: BAYFERROX, Germany or equivalent).

The casting shall be done in Synthetic Rubber/FRP moulds manufactured using mould/tool-

grade resin (Make: Revex/Reckli or equivalent).

All works shall be executed strictly as per approved shop drawings, architectural details, and

directions of the Engineer-in-Charge.

No additional payment shall be made for tools, tackles, or scaffolding.

Scope of Work Includes:

1.GFRC Pen Column: Size – 6200 mm (H) × 1080 mm (Dia/Width)

2.GFRC Book Cladding for Security Cabin: Size – 4485 mm (H) × 4825 mm (W)

3.Minimum Gate Clear Height: 6.50 metres

Complete in all respects as per drawing and direction of Engineer-in-Charge.

ABSTRACT ESTIMATE FOR COMPUND WALL

Sl. DSR 2023/ Non-DSR Non-DSR

Item of Work Unit Quantity DSR RATE DSR Amount

No. Market price RATE Amount

SITE DEVELOPMENT

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and

saplings of girth up to 30 cm measured at a height of 1 m above ground level and

2.31 removal of rubbish outside the periphery of the area cleared and clearing grass and cum 4792.88 17.60 84354.69

removal of the rubbish outside the periphery of the area cleared complete in all

2 Earth Filling

Excavating, supplying, stacking and filling of local earth (including royalty) by

mechanical transport upto a lead of 5km also including ramming and watering of the

earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of

foundation etc. complete for all lift.

B. BOUNDARY WALL

Earth work in excavation by mechanical means (Hydraulic excavator) / manual

means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm

2.8 on plan), including dressing of sides and ramming of bottoms, for all lift,

including getting out the excavated soil and disposal of surplus excavated soil

as directed, within a lead of 50m.

a) 2.8.1 All kinds of soil Cum 94.08 260.30 24,489.02

Extra for every additional lift of 1.5 m or part thereof in excavation / banking

excavated or stacked materials.

2.26.1 All kinds of soil Cum 94.08 126.80 11,929.34

4 Sand Filling

Supplying and filling in plinth with sand under floors, including watering, ramming,

consolidating and dressing complete.

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded

stone aggregate 40 mm nominal size derived from natural sources).

6 R.C.C. work M 25

Providing and laying in position ready mixed or site batched design mix cement

concrete for reinforced cement concrete work (M-25), using coarse aggregate and

fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to

5.33.1.1 accelerate / retard setting of concrete, to improve durability and workability without cum 64.96 9504.75

impairingstrength; including pumping of concrete to site of laying, curing, carriage for

all leads; but excluding the cost of centering, shuttering, finishing and reinforcement

as per direction of the engineer-in-charge, for the following grades of concrete.

Providing and laying in position ready mixed or site batched design mix cement

concrete for reinforced cement concrete work (M-25), using coarse aggregate and

fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to

accelerate / retard setting of concrete, to improve durability and workability without

impairingstrength; including pumping of concrete to site of laying, curing, carriage for

all leads; but excluding the cost of centering, shuttering, finishing and reinforcement

as per direction of the engineer-in-charge, for the following grades of concrete.

7 R.C.C. work M 25

Steel reinforcement (Fe-500D) for R.C.C. work including straightening, cutting,

5.22.6 bending, placing in position and binding all complete upto plinth level. DSR 2023 item

Foundation and plinth KG 7905.60 107.85 852618.96

All shuttering of RCC members shall be as per DSR 2023 Subhead 5. As per

Drawings & Directions of the Engineer in charge.

a 5.9.1 Foundations, footings, bases of columns, etc. for mass. Sqm 138.24 392.15 54210.82

b 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. Sqm 266.22 736.40 196044.41

c 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 288.00 961.30 276854.40

Brick work with non modular fly ash bricks conforming to IS:12894, class designation

6.34.2 10 average compressive strength in super structure above plinth level up to floor V cum 58.73 8752.55 513993.50

10 1:6 Cement Plaster

13.1.2 12 mm cement plaster of mix. Sqm 548.10 333.35 182709.14

11 1:3 Cement Plaster

13.16.1 6 mm cement plaster of mix. Sqm 152.64 300.45 45860.69

12 Acrylic Smooth Exterior Paint

Finishing walls with Acrylic Smooth exterior paint of required shade.New work (Two

13.46 or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior sqm 700.74 160.60 112538.84

primer applied @ 0.90 litre/10 sqm)

Sl.No. DSR 2025 Item Description Unit Quantity Rates

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm

thickness of existing ground prepared with proper level and ramming with tools

2.33 wooden (Dhurmos) and than rolling the surface with light roller make the Per Sqm 2569 257.00 660233.00

surface smoothen and light waterning with sprinkler and maintenance for 30

1 days or more till the grass establish properly, as per direction of officer-in-

charge. palm well developed with fresh & healthy foliage of ht. plant 210cm to

240cm in big 40cm Cement Pot

Providing and stacking of Lagerstroemia flosreginae of height 150-165 cm.in

big poly bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Peltophorum species of height 150-165 cm. in big

poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Plumeria acutifolia of height 120-135 cm. with 2-3

branches in HDPE bag of size 30 cm as per direction of the officer-in-charge

6 10443 Cineraria Per Tray 20 440.00 8800.00

7 10449 Dianthus hybrid Per Tray 20 480.00 9600.00

9 10446 Cosmos hybrid Per Tray 20 590.00 11800.00

10 10458 Petunia hybrid Per Tray 20 510.00 10200.00

11 40464 Verbena hybrid Per Tray 20 350.00 7000.00

12 10473 Vinca Hybrid Per Tray 20 400.00 8000.00

13 10474 Zinnia hybrid Per Tray 20 390.00 7800.00

Project Name:- Construction of Building Projects for The Institute of Chartered

Accountantsof India (ICAI) Bhawan at Raipur

Summary of Electrical Works

Sl.No. Services Amount

DSR 2022 DSR 2025 MARKET RATE

2 External Electrical 32,68,286.00 35,98,584.00

5 ELV System 2,53,22,282.37

Project Name:- Construction of Building Projects for The Institute of Chartered Accountantsof India (ICAI) Bhawan at Raipur

BOQ INTERNAL ELECTRICAL WORKS

Sl.No. Item Code Description of work Unit Qnty. RATE

DSR 2022 DSR 2025 MARKET RATE DSR 2022 DSR 2025 MARKET RATE

A. Circuit Cum Wiring

1 Supplying & Wiring for light point/ fan/ exhaust fan point/ call bell point with

1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface /

recessed 1.6 mm thick PVC conduit with modular switch and earthing the point

with 1.5 sqmm FRLS PVC insulated copper conductor single core cable including

providing modular box with cover of requisite number of modules including

providing cover plates as required.

a) ITEM NO 1.10.3 (DSR Primary Point Group C

2 Supplying & Wiring from first light point to next Light Point (Secondary Point)

with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in

surface / recessed 1.6 mm thick PVC conduit and earthing the point with 1.5

ITEM NO 1.55.3 (DSR sqmm FRLS PVC insulated copper conductor single core cable including required

2022) single rose and Metal box. Each 299 858.00 2,56,542.00

3 Supplying & Wiring for twin control light point with 1.5 Sqm.m FRLS PVC

insulated copper condutor single core cable in surface / recessed PVC conduit 2

way modular switch,modular plate,suitable GI box and earthing the point with

ITEM NO 1.11 (DSR 1.5 Sqm.m .FRLS PVC insulated copper conductor single core cable etc as

4 Supplying and fixing two module stepped type electronic fan regulator with

ITEM NO 1.25 (DSR proper modular plate switch box including connections etc. as required.

5 Supplying and fixing 6 Amp Socket with 6 Amp switch (Modular Type) on

ITEM NO 1.24.1 AND

1.24.4 (DSR 2022) existing board. Nos 5 225.00 1,125.00

6 Supplying & fixing suitable size GI Box with modular plate and cover in front on

surface or in recess, including providing and fixing 3pin 5/6 amps modular

ITEM NO 1.31 (DSR socket outlet and 5/6 amps modular switch etc. as required.

7 Supplying & fixing suitable size GI Box with modular plate and cover in front on

surface or in recess, including providing and fixing 2Nos 3pin 5/6 amps modular

ITEM NO 1.56 (DSR socket outlet and 2Nos 5/6 amps modular switch etc. as required.

8 Supply, installation, testing & commissioning of 6 / 16 Amp Plug Boards

consisting of a 16 Amp clip-in type modular switch with indicator and a 6/16

Amp clip-in type modular shuttered plug socket fixed on metallic concealed box

ITEM NO 1.32 (DSR including interconnections and making good the damages caused complete as

2022) required and as per direction of Engineer-in-charge. Nos 71 586.00 41,606.00

9 Supply, installation, testing & commissioning of 6 / 16 Amp Plug Boards

consisting of Two nos 16 Amp clip-in type modular switch with indicator and

2nos 6/16 Amp clip-in type modular shuttered plug socket fixed on metallic

concealed box including interconnections and making good the damages

MR caused complete as required and as per direction of Engineer-in-charge. Nos 14 924.00 12,936.00

10 Supplying, installation, testing & commissioning of suitable size GI box with

modular plate and cover in front on surface or in recess including providing and

ITEM NO 1.57 (DSR fixing 25A modular socket outlet and 25A modular SP Mcb "c" curve including

2022) connections, painting etc as required. Each 18 727.00 13,086.00

11 Supplying, installation, testing & commissioning of 20 Amp , 415volts, TPN

industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top

along with 20amps "c" curve, TPMCB, in sheet steel enclosure, on surface or in

recess, with chained metal cover for the socket outlet and complete with

ITEM NO 2.19 (DSR connections, testing and commisioning etc. as required.

12 Wiring for circuit/ submain wiring along with earth wire of following size of FRLS

heavy gauge PVC insulated copper conductor single core cable in heavy duty

PVC conduit laid in surface/ recess as required.

a) ITEM NO 1.14.2 (DSR 2X2.5 + 1X2.5 sqmm FRLS Cu wire

b) ITEM NO 1.14.3 (DSR 2X4 + 1X4 sqmm FRLS Cu wire

c) ITEM NO 1.14.4 (DSR 2X6 + 1X6 sqmm FRLS Cu wire

d) ITEM NO 1.14.9 (DSR 4X6 + 2X6 sqmm FRLS Cu wire

e) ITEM NO 1.14.10 (DSR 4X10 + 2X6 sqmm FRLS Cu wire

f) ITEM NO 1.14.11 (DSR 4X16 + 2X10 sqmm FRLS Cu wire

B. Fan & indoor Fixtures

13 Supply, delivery and fixing of Ceiling fan hook box made out of 18 swg GI sheet

and containing 10 mm dia round ms bar projecting atleast 150mm on either

side & duly bent to accommodate ceiling fan down rod bolt & having earthing

arrangement as per direction of Engineer-in-charge.

14 Supplying, installation, Testing & Commissioning of LED Recessed/ surface

Down lighter (Round/ square/ Rectangular) SMD type of following body

material with PMMA and prismatic diffuser and construction as per IS : 10322

with driver as per the requirement with Driver efficiency >85%, Operating

voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -15 deg to

40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit

protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80 , UGR (Unified Glare Rating) <

19, Flicker free (flicker should be below 5%), life time (LED,Driver & electrical

circuitary), of minimum 50000 Burning Hours with 70% of initial Lumen

maintained till life ends ,CCT 3000°K / 4000°K / 5700°K / 6000°K / 6500°K (As

per ANSI Bin), SDCM (Standard Deviation Color Matching) <3, Maximum power

consumption should not more than the specified rating and Fixture shall be

confirming to relevant BIS standards and trade mark certificate (T.C.).

Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on

housing Complete in all respect i/c connections with 1.5 sq mm FRLS, PVC

insulated copper conductor single core cable and earthing etc. as required with

Minimum 5 year OEM warranty. System lumen efficacy ≥105 and <120 lm/Watt

output . LM79 & LM80 Test report from NABL lab for all testing required for LED

fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved

by Engineer-in-Charge as per requirement. (Thermal management: heat sink of

aluminum housing such that LED junction temperature shall not rise above

90°C). Powder coated die cast /Extruded aluminum Body including trim

a) ITEM NO 1.1.4 (DSR Surface Mounted LED Light fitting 18 W

b) ITEM NO 1.1.4 (DSR Recess Mounted LED Light fitting 18 W

c) ITEM NO 1.1.3 (DSR Recess Mounted LED Light fitting 12 W

d) ITEM NO 1.1.3 (DSR Surface Mounted LED Light fitting 12 W

e) ITEM NO 1.1.2 (DSR Recess Mounted LED Light fitting 9 W

15 Supplying, installation, Testing & Commissioning of LED Recessed/ surface

Down lighter (Round/ square/ Rectangular) COB Type of following body

material and construction as per IS : 10322 with driver as per the requirement

with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency

50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge

protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥

0.95, IP20, CRI >80 , UGR (Unified Glare Rating) < 19, Flicker free (flicker should

be below 5%), life time (LED,Driver & electrical circuitry), of minimum 50000

Burning Hours with 70% of initial Lumen maintained till life ends , CCT 3000°K /

4000°K / 5700°K / 6000°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation

Color Matching) <3, Maximum power consumption should not more than the

specified rating and Fixture shall be confirming to relevant BIS standards and

trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/

Embossing/ Screen printing on housing Complete in all

respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper

conductor single core cable and earthing etc. as required with Minimum 5 year

OEM warranty. System lumen efficacy ≥105 and <120 lm/Watt output . LM79 &

LM80 Test report from NABL lab for all testing required for LED fixtures as per

BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-

Charge as per requirement. (Thermal management: heat sink of aluminum

housing such that LED junction temperature shall not rise above 90°C). Powder

coated die cast /Extruded aluminum Body including trim with Aluminum

a) ITEM NO 1.4.6 (DSR 30Watt Recessed

b) ITEM NO 1.4.5 (DSR 22Watt Recessed

16 Supplying, installation, Testing & Commissioning of Panel light 2x2 ft., of

following body material and construction as per IS : 10322 with driver as per

the requirement with Driver efficiency >85%, Operating voltage AC 140- 270

Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade,

internal surge protection of 2.5 KV with Short & Open circuit protection, THD <

10% , P. F. ≥ 0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free,

(flicker should be below 5 %), life time (LED,Driver & electrical circuitry), of

minimum 50000 Burning Hours with, 70% of initial Lumen maintained till life

ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000 ° K / 4000 ° K /

5700 ° K /6000 ° K / 6500 ° K (As per ANSI Bin), SDCM(Standard Deviation Color

Matching) <3, Maximum

power consumption should not more than the specified rating and Fixture shall

be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures

Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete

in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper

conductor single core cable and earthing etc. as required with Minimum 5 year

OEM warranty. System lumen efficacy ≥ 105 <120 lm/Watt output . LM79 &

LM80 Test report from NABL lab for all testing required for LED fixtures as per

BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-

Charge as per requirement. (Thermal management: heat sink of aluminum

housing such that LED

junction temperature shall not rise above 90 ° C). Powder coated die cast /

Extruded aluminium Body (Thickness

a) ITEM NO 1.6.4 (DSR 36Watt

17 Supplying, installation, Testing & Commissioning of LED surface mounted Batten

light of following body material and construction as per IS : 10322 with driver

(Replaceable) as per the requirement with Driver efficiency >85% ,Operating

voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40

deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit

protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be

below 5 %), life time (LED,Driver & electrical circuitary), of minimum 50000

Burning Hours with , 70% of initial Lumen maintained till life ends, CCT 3000°K /

4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation

Color Matching) <3, Maximum power consumption should not more than the

specified rating and Fixture shall be of relevant BIS standard and trade mark

certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/

Screen printing on housing. complete in all respect i/c connections with 1.5 sq

mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as

required with Minimum 5 year OEM warranty. System lumen efficacy ≥ 105

<120 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing

required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall

be as approved by Engineer-in-Charge as per requirement. (Thermal

management: heat sink of aluminum housing such that LED junction

temperature shall not rise above 90 ° C).Powder coated die cast / Extruded

aluminium Body (Thickness≥ 1.20 mm)

a) ITEM NO 1.9.1 (DSR 20Watt

18 Supply , installtion, testing and comisioning of External down lighter for Accent,

Façade lighting and similar application 15W, High efficient Surface mounted LED

round downlighter with white powder coated, pressure die cast aluminium

housing. High transmittivity Toughened glassr provides soft light. LED Efficacy

80% Typ driving current is 146,IP65 and IK06, Ambient temp-0 to 45Deg,CCT -

6500K(Available in3000K and 4000K also),50,000 hrs @ L70 life. Driver

efficiency>85%,THD<10%, Powerfactor>0.95, Luminaire lumen ≥ 1350 lm. -

Cutout Dia-ø100mm Surface mounted downlight with high performance and

efficiency. Make Wipro LD08-151-029-65-SM

19 Surface mounted 10 watt LED decorative alluminium Batten Light for Mirror

Lighting over wash basin,CRI not less than 80,CCT of 5700 degree K) consists of

white powder coated , die-cast Alluminium housing with high quality frosted

diffuser for glare-free uniform lighting distribution and with dali dimmer similar

to Wipro (CAT No: LL20-111-XXX-65AL1).

20 Surface Mounted LED Bulkhead fitting(1000Lumen/10W) CRI not less than

80,CCT of 5700 degree K) consists of white powder coated , die-cast

Alluminium housing with high quality frosted diffuser for glare-free uniform

lighting distribution and with dali dimmer Similar to Wipro (CAT No:LW07-141-

21 Item No:- 1.38 (DSR Supplying and fixing call bell/ buzzer suitable for single phase,230 V, complete

2022) as required. Each 4 396.00

22 Supplying,installation,testing and commissioning of Passive Infrared(PIR)

technology based occupancy sensor having high preformance, non regulating

programmable type, suitable for connected load upto 10Amp , for 2.8mtr

mounting height up to 5 m diameter coverage area along with necessary

ITEM NO 15.1 (DSR fixing arrangements i/c programming at site etc. complete as required.

23 Supplying,installation,testing and commissioning of Microwave sensor

technology based occupancy sensor with day light dimming(lighting level shall

be regulated as per availability of natural day light in an area along with

occupancy detection.) having high preformance, regulating programmable

type, suitable for connected load upto 10Amp , for 4mtr mounting height up

to 5 m diameter coverage area along with necessary fixing arrangements i/c

ITEM NO 15.3 (DSR programming at site etc. complete as required. Similar to Wipro

24 Supplying, installation, testing and commissioning of BLDC ceiling fan including

wiring the down rod, earthing etc as required.

a) ITEM NO 2.2.3 (DSR 1200 mm sweep

25 Supplying, installation, testing and commissioning of metal body wall mounted

fan including earthing etc as required.

26 Supplying, installation, testing and commissioning of Exhaust fan including

louvres, Ceiling Rose & Electric Connection as required.

C. Panels, MDBs, DBs. MCBs

Supply, installation, testing and commissioning of cubicle type sectionalised,

front operated top entry dust and vermin proof M.V.Panel Boards suitable for

operation at 415V, 3 phase, 4 wire, 50Hz distribution system fabricated out of

2.0 mm thick CRCA sheet, insulated busbar with heat shrienkable PVC sleeve,

base channel, wiring with space heater, thermostat and control MCBs shall be

provided for all vertical sections of main LT Panel, all hinged door shall be

earthed through 2.5 sq mm tinned braided, the incoming and outgoing feeders

shall be accommodated in a modular arrangement, detachable gland plates,

adequate size cable alley, Sign writing, Painting, Earthing, Numbering, Danger

plate, including PVC insulated copper FRLS wires of minimum 1.5 sq.mm & 2.5

sq.mm for CT's etc. with all accessories including interconnections, earth bus,

Surge protection Device(SPD) etc. as required.

27 Main LT PANEL (To be installed in Substation Building)

Busbar -1000 Amp Al busbar with SC rating of 50 KA suitable for operation at

415 Volt, 50 Hz, 3 Phase supply

One (1)- Incomer feeders (1 nos from EB) each comprising of

One (1) - 800A,TPN, 50KA,EDO ACB

One(1)- Multifunction digital meter suitable for three phase four wire system,

unbalanced loading CL 1.0, flush mounting with Voltage, Current, pf. KW, KWH,

KVA, KVAr, KVAh, KVArHr

One set - Indicating lamp for ON/OFF/Trip and Phase indication with control

One(1) set of 800/5A ,15VA , Cl 1.0, CTs.

One (1)- Incomer feeders (1 nos from Dgset1) each comprising of

One (1) - 500A,TPN, 50KA,Motorised MCCB

One(1)- Multifunction digital meter suitable for three phase four wire system,

unbalanced loading CL 1.0, flush mounting with Voltage, Current, pf. KW, KWH,

KVA, KVAr, KVAh, KVArHr

One set - Indicating lamp for ON/OFF/Trip and Phase indication with control

One(1) set of 500/5A ,15VA , Cl 1.0, CTs.

One (1)- Incomer feeders (1 nos from Solar inverter) each comprising of

One (1) - 63A,TPN, 25KA,MCCB

One set - Indicating lamp for ON/OFF/Trip and Phase indication with control

Electrictro mechanical interlock for incomers

One (1)- Changeover switch

One (1) - 250A,TPN, Change over switch

One set - Indicating lamp for ON/OFF/Trip and Phase indication with control

Three (3) - Outgoing Feeders (For One 200KVAR APFC Panel, One Fire Fighting

Panel and One Spare) each comprising of

One (1) - 400A,TPN, 25KA,MCCB

One set - Indicating lamp for ON/OFF/Trip and Phase indication with control

One (1) - Outgoing Feeders (For One EV Charging panel) each comprising of

One (1) - 200A,TPN, 25KA,MCCB

One set - Indicating lamp for ON/OFF/Trip and Phase indication with control

Five(5) - Outgoing Feeders ( 2nos VRF odu Panel, Two for Ups and One Spare)

each comprising of

One (1) - 160 A,TPN, 36KA,MCCB

One Set ON/OFF Indicating lamp with control fuse/ MCB with required other

Six(6) - Outgoing Feeders (Two for Lift, One for STP, One for Water supply,

One External Lighting and One Spare) each comprising of

One (1) - 63 A,TPN, 36KA,MCCB

One Set ON/OFF Indicating lamp with control fuse/ MCB with required other

Two (2) - Outgoing Feeders for (Two spare) each Comprising of

One (1) -32A TPN 25KA MCCB with required other accesories.

One Set ON/OFF Indicating lamp with control fuse/ MCB with required other

Fifteen (13) - Outgoing Feeders (13nos PDB and AC DB and 2nos spare) each

One (1) -63A TPN 10KA MCB with other required accesories.

Six (6)- Outgoing Feeders (4Nos LDB and 2nos spare) each Comprising of

One (1) -32A TPN 10KA MCB with other required accesories.

Four (4)- Outgoing Feeders (for spare) each Comprising of

One (1) -32A DP 10KA MCB with other required accesories.

*The Switchboard shall be complete with all interconnections, risers, internal

wiring, labels, control/circuit fuses or MCB, Space heater, internal lighting &

Thermocouple etc. complete as required.

MR PANEL AS ABOVE Set 1 17,26,748.00 17,26,748.00

28 200 KVAR APFC Panel

Supply, Installation, testing and commissioning of Automatic Power Factor

Correction (APFC) panel, indoor type floor mounted free standing totally

enclosed, extendable, IP 42, of following capacity for 3 phase, 415 V + 10 %, 50

Hz AC System for Ambient temperature -5°C to +40°C, fabricated in

compartmentalized designed made of CRCA sheet steel of 2.0mm thick for

framework & covers, 3 mm thick for gland plate i/c cleaning & finishing

complete with 9 tank process for powder coated of approved shade ( RAL 7032-

Siemens gray or as approved by Engineer-in-Charge), having front section

(switch gear and control accessories) and rear section capacitor and reactor,

front and rear access, having suitable current carrying capacity, extensible TPN

Aluminum alloy bus bar of high conductivity, DMC/SMC bus bar supports,

bottom base channel of MS Section, fabrication shall be done in transportable

section, entire panel shall have common copper earth bar of minimum size of

25mm x 5mm with 2 nos. earth studs, the earth terminals provided on the body

of capacitor bank shall also be bonded to the main capacitor panel earth bus

with 2 nos. 8 SWG or 6 SWG GI earth wires/

equivalent size of copper conductor cable, forced ventilation for maintaining

temperature rise not more than 5°C from ambient, interconnections,

connections with 14% detuned reactor and heavy duty 525 V ISI marked

Impregnated MPP(Metalized Polypropylene) Capacitor (IS 13340 Part -1 & 2)

APFC Panel shall be in compliance with IS :16636 & CPWD Specifications etc. as

per below details

Suitable capacity MCCB Microprocessor base with O/C, S/C, E/L release of TPN

50KA breaking capacity (Ics=Icu), ON, OFF, Trip, R, Y, B - LED Indicating Lamp set

along with required Instruments and accessories with extended rotary handle

and door interlocking arrangement. Current rating of the Incomer in ampere

shall be APFC Panel rating in KVAR x 1.4 x 1.5 or Nearest higher standards

(B) Instruments & Indications

i) 3-Phase current sensing APFC microprocessor relay/controller , advance 8/12

stages (8 stages for capacity below 100 KVAR and 12 stages 100 KVAR & above)

with Communication Ethernet/ RS485/ SNMP port open protocol for BMS

integration as per approved by Engineering in charge and having display of

Phase wise V, A, PF, Cos-Phi, Kw, KVA, KVAR, THD-V , THD-I, harmonics up to 31

level. 3 nos of dual core CT's accuracy class 1, 15VA at incomer of PCC Panel

ii) Auto Manual Selector switch, auxiliary contactors with timer for delay in

iii) Digital Multi function meter with LED Display for V, A, PF, KW, KVA, KVAR,

THD-V & I, Frequency.

iv) Suitable rating control transformer shall be provided for control and

indication circuit.

v) All components like control transformer, meter, relay and indicating lamp

shall be protected by using suitable rating individual MCB's.

vi) Wiring of the control circuit shall be done by using 2.5 sq mm, FRLS 1100 V

grade, PVC insulated multi stranded copper control wire.

1.3 Amp per Sq.mm, TPN, Electrolytic grade Aluminum bus bar of capacity 1.25

times of incomer rating as per CPWD specification.

(D) Outgoings (APFC Section)

Selection of the capacitors combinations shall be for continuous rating and each

capacitor bank shall have suitable capacity Heavy Duty ISI Marked Capacitor,

capacitor duty contactor, the capacitor shall be mounted on channel with base

of perforated M S Powder coated sheet, connections inter connections etc. and

other features as per CPWD Specifications and relevant IS Code having

(i) Capacitor bank ratings & stages shall be as per the technical

specifications sheet of NIT.

(ii) Capacitor will be MPP self healing type with discharge resistor, pressure

release mechanism.

(iii) Since Capacitor Voltage is 525 Volts, thus higher KVAR has to be considered

to get rated output at 415 Volts.

(iv) 14% Detuned Reactor of class H insulation & 150% linearity in series with

(Note: Technical specifications sheet for selection of the capacitors

combinations shall be provided by the NIT Approving Authority with due

consideration of number of capacitors i.e. 1 KVAR, 2 KVAR, 3 KVAR, 5 KVAR, 10

KVAR.....for smooth correction).

a) Item No:-4.1.7 (DSR-

29 UPS PANEL(O/G)

Two (2) no. Incomer- 160 Amp TPN ,25 KA MCCB with 3 Nos Phase indicating

lamps with control fuse/ MCB Digital Voltmeter and Ammeter with selector

switch with other required accessories.

Busbar - 400 Amp,25KA Cu TP2N busbar suitable for operation at 415 Volt, 50

Hz, 3 Phase supply

Six(6) - Outgoing Feeders for (Three nos UDB and 3nos spare) each Comprising

One (1) - 63 Amp TPN, 10 KA MCB (C-Curve)

Six(6) - Outgoing Feeders for (3Nos ELDB and 3nos spare) each Comprising of

One (1) - 32 Amp TPN, 10 KA MCB (C-Curve)

Four(4) - Outgoing Feeders for (4nos spares ) each Comprising of

One (1) - 32 Amp DP, 10 KA MCB (C-Curve)

MR PANEL AS ABOVE Set 1 2,73,476.00 2,73,476.00

30 Lift Panels

One (1) Incomer - 63 Amp, 25 KA, 4P MCCB with 3 Nos Phase indicating lamps

with control fuse/ MCB Digital Voltmeter and selector switch

Busbar - 160 Amp Al busbar with SC rating of 25 KA suitable for operation at

415 Volt, 50 Hz, 3 Phase supply

One (1) - Outgoing Feeder with 63 Amp, 10Ka 4P MCB for lift supply

Four (8) - Outgoing feeder with 32A,2P, 10KA MCB for ARD battery

MR charger,Liftwell lighting & one nos spare No 2 73,474.00 1,46,948.00

31 UPS Incomer -1

One (1) no 100 Amp TPN ,25 KA MCCB with required other accessories &

suitable metal enclosure concealed in wall for power supply to 40KVA UPS.

31 VRF ODU PANEL 1

One (1)-Incomer feeders from Main LT panel

One (1) - 160 Amp TPN ,36 KA MCCB with 3 Nos Phase indicating lamps with

control fuse/ MCB Digital Voltmeter and Ammeter with selector switch ( Make-

LEGRAND-DPX3 / Siemens-3VM Model/ Schneider- NSX/ ABB-TMAX XT/ LK)

One(1)- Multifunction digital meter suitable for three phase four wire system,

unbalanced loading CL 1.0, flush mounting with RS 485 communication port for

reading Voltage, Current, pf. KW, KWH, KVA, KVAr, KVAh, KVArHr(BMS

One set - Indicating lamp for ON/OFF/Trip and Phase indication with control

One(1) set of 160/5A ,15VA , Cl 1.0, CTs.

One(1) Digital Ammeter with S/S.

One(1) 0-500V Digital Voltmeter with S/S.

Busbar -200 Amp Al busbar with SC rating of 36 KA suitable for operation at 415

Volt, 50 Hz, 3 Phase supply

Three(3) - Outgoing Feeders (For 2nos AHU starterl and One Spares) each

One (1) - 63A,TPN, 25KA,MCCB

One Set ON/OFF Indicating lamp with control fuse/ MCB with required other

Four (4) - Outgoing Feeders (For 3nos for VRF Outdoors and 1nos Spare) each

One (1) - 63A,TPN, 10KA,MCB

PANEL AS ABOVE (Make of switch gears: Legrand/ LK/ Schneider/ Seimens/

1 VRF ODU PANEL 2

One (1)-Incomer feeders from Main LT panel

One (1) - 160 Amp TPN ,36 KA MCCB with 3 Nos Phase indicating lamps with

control fuse/ MCB Digital Voltmeter and Ammeter with selector switch ( Make-

LEGRAND-DPX3 / Siemens-3VM Model/ Schneider- NSX/ ABB-TMAX XT/ LK)

One(1)- Multifunction digital meter suitable for three phase four wire system,

unbalanced loading CL 1.0, flush mounting with RS 485 communication port for

reading Voltage, Current, pf. KW, KWH, KVA, KVAr, KVAh, KVArHr(BMS

One set - Indicating lamp for ON/OFF/Trip and Phase indication with control

One(1) set of 160/5A ,15VA , Cl 1.0, CTs.

One(1) Digital Ammeter with S/S.

One(1) 0-500V Digital Voltmeter with S/S.

Busbar -200 Amp Al busbar with SC rating of 36 KA suitable for operation at 415

Volt, 50 Hz, 3 Phase supply

Three (3) - Outgoing Feeders (For 2nos for VRF Outdoors and 1nos Spare) each

One (1) - 63A,TPN, 10KA,MCB

PANEL AS ABOVE (Make of switch gears: Legrand/ LK/ Schneider/ Seimens/

32 Supplying and fixing following way, horizontal type three pole and neutral,

sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with

tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections,

powder painted including earthing etc. as required. (But without

MCB/RCCB/Isolator). (For all Floors LDBs, PDBs, ACDBs & UDBs)

a) ITEM NO 2.4.1 (DSR 4 way, Double door(4+12)

b) ITEM NO 2.4.2 (DSR 6 way, Double door(4+18)

c) MR 4 way, Double door(8+18) Each 8 5,075.00 40,600.00

d) MR 6 way, Double door(8+18) Each 4 6,202.00 24,808.00

33 Supplying and fixing of following ways surface/ recess mounting, vertical type,

415 volts, TPN MCB distribution board of sheet steel, dust protected, duly

powder painted, inclusive of 200 amps tinned copper bus bar, common neutral

link, earth bar, din bar for mounting MCB’s (but without MCB’s and incomer ) as

required . (Note : Vertical type MCB TPDB is normally used where 3 phase

outlets are required.) . (For ACDBs)

a) ITEM NO 2.5.1 (DSR 4 way, Double door(4+12)

b) ITEM NO 2.5.2 (DSR 8 way, Double door(4+24)

34 Supplying and fixing following way, single pole and neutral,sheet steel, MCB

distribution board, 240 V, on surface/ recess, complete with tinned copper bus

bar, neutral bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without MCB/RCCB/Isolator)

a) ITEM NO 2.3.2 (DSR 8 way, Double door

b) ITEM NO 2.3.3 (DSR 12 way, Double door

35 Supply and fixing 5A to 63A rating, 240/415V , 10kA, "C" curve, miniature circuit

breaker suitable for inductive load of following poles in the existing MCB DB

complete with Connections, testing and commissioning etc as required.

a) MR 63 Amps, FP 10 KA MCB (C-Curve) Each 12 3,688.00 44,256.00

b) ITEM NO 2.10.5 (DSR 32 Amps, FP 10 KA MCB (C-Curve)

c) ITEM NO 2.10.4 (DSR 32 Amps, TP 10 KA MCB (C-Curve)

d) MR 63 Amps, DP 10 KA MCB (C-Curve) Each 2 1,930.00 3,860.00

e) ITEM NO 2.10.2 (DSR 32 Amps, DP 10 KA MCB (C-Curve)

f) ITEM NO 2.10.1 (DSR 6 Amp to 32 Amp, 10 KA SP MCB (C-Curve)

36 Supplying and fixing following rating, Four pole, (three phase and neutral), 415

volts, Residual currents circuit breaker (RCCB), having a sensitivity current

30mA in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

a) ITEM NO 2.15.3 (DSR 63Amps 4P 415 volts RCCB 30 mA

b) ITEM NO 2.15.2 (DSR 40Amps 4P 415 volts RCCB 30 mA

37 Supplying & Testing of 1.1 KV grade Aluminium XLPE Armoured power cable of

following size suitable for 415 Volt, 3Ph, 50 c/s supply.

38 Supplying & Testing of 1.1 KV grade Cu XLPE Armoured power cable of following

size suitable for 415 Volt, 3Ph, 50 c/s supply.

39 Supplying & Testing of 1.1 KV grade Cu XLPE Un Armoured (Flexible) power

cable of following size suitable for 415 Volt, 3Ph, 50 c/s supply.

40 Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of

1.1KV grade of following size direct in ground including excavation,sand

cushioning,protective covering and refilling the trench etc as required.

a) ITEM NO 7.1.1 (DSR Upto 35 sq. mm

41 Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE power

cable of 1.1KV grade of following size on wall surface as required.

a) ITEM NO 7.7.1 (DSR Upto 35 sq. mm

b) ITEM NO 7.7.2 (DSR Above 35 sq. mm and upto 95 sq. mm

c) ITEM NO 7.7.3 (DSR Above 95 sq. mm and upto 185 sq. mm

d) ITEM NO 7.7.4 (DSR Above 185 sq. mm and upto 400 sq. mm

TERMINATION OF CABLES

42 Supply & Making end Termination with brass compression gland and

Cu/aluminium lugs for PVC insulated and PVC sheathed cable of 1.1 kv grade

(without cost of Cable)

b) ITEM NO 9.1.32 (DSR 4C X 10 sqmm(19 mm)

c) ITEM NO 9.1.33 (DSR 4C X 16 sqmm(28mm)

d) ITEM NO 9.1.34 (DSR 4C X 25 sqmm(28mm)

e) ITEM NO 9.1.19 (DSR 3.5C X 70 sqmm(35 mm)

f) ITEM NO 9.1.27 (DSR 3.5C X 185 sq. mm (57mm)

h) ITEM NO 9.1.30 (DSR 3.5C X 300sq. mm (70mm)

43 Supply & making of Sigle Compression cable glands and crimping type Cu. cable

lugs with required tools and equipments as per IS. The glands and lugs shall be

suitable for 2XY cables.

Supplying and laying of fallowing dia DWC HDPE pipe ISI marked along with all

accessories like socket, bend, couples etc. conforming to IS 14930, Part II

complete with fitting and cutting, jointing etc. direct in ground (75 mm below

ground level) including excavation and refilling the trench but excluding sand

cushioning and protective covering etc., complete as required.

b) ITEM NO 14.16.1 (DSR

c) ITEM NO 14.16.5 (DSR 200 mm dia

45 Supply Installation, Testing and Comisioning of perforated Hot dipped

Galvanised iron tray (Galvanisation thickness not less than 50 microns) with

perforation not more than 17.5% in convenient sections, joined with

connectors, suspended from the ceiling with G.I suspenders including GI bolts &

nuts etc as required.

a) ITEM NO 4.6.2 (DSR

150 mm (W) X 50 mm depth X 1.6 mm thickness

b) ITEM NO 4.6.4 (DSR

300 mm (W) X 50 mm depth X 1.6 mm thickness

c) ITEM NO 4.6.6 (DSR 450 mm width X 50 mm depth X 1.6 mm thickness

Supplying, installation, Testing & Commissioning of of following capacity at full

load (Unity Power Factor) at operating temperature 0 to 40 deg C, Relative

humidity 0 to 95%, Online double conversion true sine wave Uninterrupted hot

swappable (allow for the replacement or addition of battery modules without

shutting down the entire system) modular Power Supply (UPS) system with N+1

modules (N denotes total number of moduels requird for rated capacity). The

UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back

up (Battery VAH capacity shall not be less than 1600 VAH per KVA of UPS rating

per Hour backup time) on full load (Battery shall be VRLA, SMF in ABS

Container) and Static Bypass switch alongwith provision for manual bypass,

suitable isolation transformer for additional protection against neutral faults

etc. UPS shall have inbuilt phase sequence correction.

The UPS systems offered are to be of the latest technology with Digital Control

Microprocessor based for reliable operation using Insulated Gate Bipolar

Transistor (IGBT)'s both for the rectifier &

inverter (3 Level) with PWM (Pulse Width Modulation). The quality of design,

manufacturing and inspection process should confirm to the relevant

International standards such as IEC/EN/VDE. The operating efficiency of the UPS

systems shall be >96% while operating on battery mode and delivering quality

power to the 100% non-linear loads. Current total harmonic effect(ITHD) on the

input grid shall be < 5% at 50 %load. (The required LC ( inductor (L) and a

capacitor (C)) filters shall be included in UPS cost), extreme power factor kit to

be included to limit the input power factor (PF) to 0.99 and output power factor

shall be unity (i.e. kw rating of the UPS shall be kva rating x 1 ), however UPS

shall be suitable to take load at 0.7 laging to 0.7

leading power factor loads. UPS shall be suitable for incoming supply AC :

3Phase 400V +/-20%, 50 Hz +/-5 Hz, AC Output voltage: 3Phase 415 Volt, 50 Hz

+/- 0.2Hz, Overload capacity of 120% for 10 mins, Sine wave output. Non

condensing, noise level less than 60db at 1 meter distance, protections: Input

Under voltage over voltage, abnormal out voltage, battery over charging,

output over current, short circuit protection, battery deep discharge protection,

UPS must comply with low voltage electromagnetic compatibility (EMC)

achieved as per EN 6204, EN6204 Part I and Part 2, it shall be a Voltage and

Frequency Independent (VFI)-type UPS. Communication RS232/RS485/SNMP

port open protocol for BMS integration, all hardware & software for iOT

Communication as per approved by Engineering in charge. Required battery

racks and interconnecting copper conductor cables of suitable size and

connectors and all required accoseries are inclusive of the cost). This system

must provide a means for logging and alarming of all monitored points plus

email notification. Forced air-cooling with integral inbuilt fans with redundancy

(if one fan fail UPS should be able to handle at least 80% of the load, Noise

Level 65 DB at 1 meter distance. The system shall be in compliance IEC 62040-

1,2 & 3, IS: 16242 and CPWD Specification. Display Panel (minimum) (In-build 5

inch or more LC Display / LED ) to display : a) Input: Voltage, current, Frequency.

b) Bypass: Voltage, Frequency. c) Output: Voltage, frequency, Current.

d) Battery: Voltage, Capacity. e) Load: KVA, KW, Percentage.

f)Temperature: STS, Inverter, PFC. g) Event Logging & Statistical Data (On

LCD/LED): UPS should capture and display up to 3000 events like: Over

temperature / DC Bus Fail / Fan Fail / Fuse Fail / Overload / Short-circuit /

Device Fail / Inverter Fail / Rectifier Fail / Bypass Fail, etc. h) Statistical Data: No.

of power failures / Transfers to Bypass / Total Running time, etc. i) Mains Mode

of Operation /Battery Mode of Operation / Bypass feeding the load / UPS Fault

/Battery charging and discharging, overload, battery voltage and battery

capacity. j) Audible Alarms : Mains Failure, Battery Low Alarm, UPS Overload,

Fault, Shutdown, Input Over, Under Voltage, Output Over, Under Voltage,

Battery Over, Under Voltage, Over Load and short circuit, Over Temperature.

The UPS should have QR code which should contain drawing, test report OEM

manual,Geo- Tag of manufacturing location etc.

46 ITEM NO 5.2.4 (DSR:-

2025) 40KVA (Each Power module shall be < 10 KVA) Nos 2 5,99,469.00 11,98,938.00

47 Supply, delivery, installation & testing of TV outlet boards containing a clip-in

type modular TV Socket outlet fixed on metallic concealed box including

ITEM NO 1.24.7+1.27.1 connections and making good the damages caused complete as required and as

(DSR 2022) per direction of Engineer-in-charge. Each 4 446.00 1,784.00

48 Wiring to TV Antenna Socket outlet from junction box with Coaxial copper

conductor TV antenna cable run inside prelaid conduit complete including

ITEM NO 1.19 (DSR termination, testing etc complete as required and as per direction of Engineer-

49 Sullying and fixing of 20mm medium class PVC conduit along with accessories in

ITEM NO 1.21.1 (DSR surface/recess including cuttting the wall and making good the same in case of

2022) recess conduit as required. Mtr 160 128.00 20,480.00

G. Miscllaneous Items

50 MR Supplying 11 kV hand gloves as reqd. Set 2 1,357.00 2,714.00

Supplying and Laying Rubber mat 1M X 2M X 2.0MM thick to withstand 1.1 KV

dielectric strength, Electrical Safety/Shock Chart & SLD etc as required.

52 Providing and fixing LT danger notice plate of 200 mm X 150 mm, made of mild

steel, at least 2 mm thick, and vitreous enameled white on both sides, and with

MR inscription in single red colour on front side as required. Each 2 232.00 464.00

53 Supplying of First aid box as approved by St.John Ambulance Brigade/ Indian

MR Red Cross Society and confirming to IS 2217/ 1963. Each 2 543.00 1,086.00

54 S/F of Shock Treatment chart duly glazed mounted on Aluminum Frame with

MR sheet glass as required. Each 2 644.00 1,288.00

55 Providing & fixing of M.S. angle iron with fixing materials and painting for cable

MR racks in trenches/ on walls etc .as required. Kg 100 172.00 17,200.00

S/F of Shock treatment/ restoration charts written in Hindi/ local lenguage and

English duly framed and covered with 3.0 mm glass as required.

57 Supplying of Caution Boards manufactured out of 16 SWG, MS sheet of

450mmx 300mm size duly painted white and having `MAN ON LINE' and 'DO

NOT SWITCH ON' written in Red complete with hanging arrangement as

MR required and & approved by the Engineer Incharge. Each 2 202.00 404.00

58 Earthing with CU earth plate 600 mm X 600 mm X 3 mm thick including

accessories, and providing masonry enclosure with cover plate having locking

arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and

ITEM NO 5.6 (DSR 2022) salt as required. Set 11 13,838.00 1,52,218.00

59 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including

accessories, and providing masonry enclosure with cover plate having locking

arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and

ITEM NO 5.1 (DSR 2022) salt as required. Set 8 7,472.00 59,776.00

60 Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia GI pipe from

ITEM NO 5.10 (DSR earth electrode including connection with brass nut, bolt, spring, washer

2022) excavation and refilling etc. as required. Mtr 195 1,551.00 3,02,445.00

61 ITEM NO 5.14 (DSR Providing and fixing 25 mm X 5 mm dia copper strip on wall/surface or in recess

2022) for connection etc. as required. Mtr 100 1,162.00 1,16,200.00

62 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe (with supply

ITEM NO 5.11 (DSR of pipe)from earth electrode including connection with G.I. nut, bolt, spring,

2022) washer excavation and re-filling etc. as required. Mtr 120 706.00 84,720.00

63 Providing and fixing 50 mm X 5 mm dia GI strip on wall/surface or in recess for

MR connection etc. as required. Mtr 300 343.00 1,02,900.00

64 ITEM NO 5.15 (DSR Providing and fixing 25 mm X 5 mm dia GI strip on wall/surface or in recess for

2022) connection etc. as required. Mtr 200 244.00 48,800.00

Lightning Protection

65 Providing and fixing of lightning conductor finial, made of 25 mm dia 1000 mm

long, Solid Copper , having multiple prong at top, with 85 mm dia 6 mm thick

copper base plate including holes etc. Along with Test junction complete as

MR required. Nos 8 8,732.00 69,856.00

66 Providing and fixing testing joint, made of 20mm x 3mm thick GI strip, 125mm

ITEM NO 6.12 (DSR long, with 4nos of GI bolts, nuts, chuck nutts and spring washer etc. complete as

67 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall

ITEM NO 6.7 (DSR 2022) for lightning conductor complete as required.(For horizontal run) Mtr 423 126.00 53,298.00

68 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall

ITEM NO 6.8 (DSR 2022) for lightning conductor complete as required.(For vertical run) Mtr 60 197.00 11,820.00

69 ITEM NO 6.14 (DSR Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in

2022) ground as required. Mtr 40 195.00 7,800.00

Project Name:- Construction of Building Projects for The Institute of Chartered Accountantsof India (ICAI) Bhawan at Raipur

BOQ External Electrification Works

Unit Rate Amount

Sl No. Description Unit Qty

DSR 2025 MARKET RATE DSR 2025 MARKET RATE

Outdoor Fixtures

1 Post top Lights

Supply of LED Post Top with a system lumen output of 3500 lumens =

and a minimum system efficacy of >90 lm/W. The luminaire shall

have a rated system lifetime of 25,000 burning hours at L70. The

luminaire should have a color temperature of 6000K and CRI > 80.

The luminaire shall meet IP65 with THD < 20% and PF > 0.9. The

luminaire shall have closed diffused optics with polycarbonate

diffuser board. The fixture is similar to Wipro (CAT No:LP07-431-

XXX-57-CL) or Equivalent of Crompton/ Unilux . This is including

cost of all material, conveyance, royalities as directed by Engg-in-

charge all complete.

Installation of LED post tops includes preparing designing & erecting

a foundation in the ground with anchor bolts to suit the fixing of base

plate, fixing of post top on foundation using anchor bolts & the base

plate. The contractor shall ensure all post tops installed are in line

Pole height: 2.5 to 3 m above ground level.

Body of the pole: Hot dip GI with matt finish & 70% grey/black color

or as specified by EIC.

Junction Box: Inbuilt with MCB, connector etc.,

Desired output lux level:15(+/-3)

Protection: IP65 class I

Voltage range : 210-270

Colour temprature : 5700K (neutral)

2 Single Arm Street Lights:

Supply, erection, testing & commissioning of road lighting HDG

Octagonal Pole conforming to IS 875 and BS EN ISO 1461 & 410

SP 33 of 7.0 meter with base plate drilling of 1" dia hole on the

upper portion of the pole for the installtion of street light and 1" dia

hole on the lower portion of the pole for entry of the wire Base pole

paintng of red oxide and two coats of black enamel paint. The poles

shall have extra provided and fixed with 4'x2' dia being erected by

laying 5'x2'x2' (length, breadth and width) cement concrete block in

the ratio 1:3:6 and block be continued up to 1 feet above the ground

level i.e 4 feet below ground level including surface plastering the

job including excavation of pole with 4 feet deep and refilling the

same after installation of the pole and with holes at top of the pole

for fixing ring type single armed GI braket for the installation of the

integral flood light luminaire of 70 watt (Make : Wipro (Cat no: LR09-

781-XXX-57-XX). The Dust and wheather proof gasket using for

250mm x 200mm x 150mm deep box nominal size of 16 SWG thick

MS sheet cable looping box with the existing pole with MS clamp

made out of 25mm x 3mm thick flat iron with suitable nuts and bolts

complete with hinged cover and locking screws earth studs

neoprene gasket suitable for Nos 4 pole mounted including supply

and fixing one no 6 Amp MCB carrier with base and 4 way 60 Amp

terminal block suitable to receive PVC armoured cable fixed on

suitable size Baketillte sheet base complete connection through GI

pipe (classB) 40 mm dia Nominal 1.5 mtr length along the pole or

protection of underground cable (on vertical run) with painting all

complete as the direction of EIC.

3 Spike / focus Lights

Supply, Installation,Testing & commissioning of IP-65, LED Garden

Spike Light including 1 no. of 9 watt LED luminairs & Basewith

BrickMasonry work (200 x 200 x 200)mm for the above fitting as per

EIC of approved make including with all,., materials & labour..

(Make: Wipro CAT No. LF05-600-036-27-XX ).

4 Gate Lighting

Supply, installation, testing & commissioning of 40W Gate Lighting

with other necessary arrangements like Pedestal, loose wire box &

connectors etc. Make:-Wipro (CAT No:LP07-501-XXX-57-CL).

Supply, installation, testing & commissioning of 11W STATIC

COLUMN Bollards Light with other necessary arrangements like

Pedestal & connector etc. Similar to Wipro CAT No. LB14-131-XXX-

6 2 way Up/Down Light

Supply, installation, testing & commissioning of 2X12W LED 2way

Up/Down Light including all other accessories & labour etc as per

EIC. Similar to Wipro Make : Cat no:- LW35-271-029-30UDX).

7 External Feeder Pillar for External Lighting

Design, Supplying, Installation, testing and commissioning of 415 V

feeder pillar panel compartmentalised, factory made Godrej Almira

type suitable for outdoor installation, made up of CRCA sheet steel

of thickness not less than 2 mm with a weather proof canopy of top,

double door construction, IP 54 protection, anti corrosive chemical

resistant paint with, automatic dawn and dusk with astronomical

controller for street light outgoing, , complete with Aluminium bus

bars, inter-connection with solid/ stranded copper conductor wires/

copper strips, glands neutral links, etc., and mounted with following

switch gears, etc., complete as required with detailed specifications:

, energy saver for automatic switching ON/OFF as per pre-sets time

cycle, digital multifunctional meter and suitable CT etc., including

concrete pedestal and associated civil works.

. Busbar-100 Amp Al busbar with neutral bus SC rating of 25 KA

suitable for operation at 415 Volt, 50 Hz, 3 Phase supply

One (1) - 63 A,TPN, 25KA,MCCB Incomer

One(1) set of – 63/5A , 15VA , CL 1.0, CT

One Set ON/OFF Indicating lamp with control fuse/ MCB.

one set of appropriate Contactor & Digital Timer at incomer side.

4 Nos - 16 Amp TPN MCB Outgoing

3 Nos - 16 Amp DP MCB Outgoing

1 No.s - 16 Amp DP MCB with 6/16 Amp socket outlet with 10 Amp

modular switch and 1 No- Bracket Holder with 6 Amp Modular

DG Sets & Other Accessories

8 320 KVA Silent type DG Sets & Other Accessories

Supply Installation Testing And commissioning of 320KVA at 0.8pf

415V 50Hz 3phase CPCB IV+ DG Set w complete with 1500 RPM

Diesel Engine of suitable BHP & AC Brush less Alternator mounted

on a common base Frame & coupled through a flexible coupling or

Alternator 1. 1500 RPM, 1P or 3P, Brushless type, screen

protected, revolving field, Self-excited alternator conforming to

IS/IEC 60034-1 IP23, with standard Alternator Protection (over

voltage, over speed & Under voltage) 2. A reliable long life with

superior class 'H' insulation with temperature rise to Class H

Diesel Engine: Engine: Engine should comprise of Silencer,

Electronic governor from >25 KVA & above, suitable rating battery ,

Battery charging alternator, battery charger , Inbuilt Fuel tank with

fuel pipe, AVM pads , Control panel with 3P MCCB of suitable rating

with short circuit protections ( 25kA, 36kA, 50kA) with

microprocessor based controller indicating genset parameters ( i.e.

volt, amps, KWH, KVAR, Hrs etc.), The diesel engine shall be

capable of providing 10% overload for 1 Hr for every 11 Hrs of

continuous running at full load.

The DG set shall be supplied as per OEM specifications and shall

be tested at site along with below.1. CRDI Engine >25 KVA DG

set2. Water cooled Radiator coupled to engine3. Dry type air

cleaner with service indicator4. First fill of lube oil, Coolant & first fill

of Diesel5. Electrical starter motor with soft start System6. Battery

charging alternator7. Remote Monitor system >58.5 KVA & Above8.

2 years / 5000 Hrs Warranty from commissioning or 30-month form

supply.9. Emission control system - EGR & (DOC, SCR for >75 KVA

DG set)10.10 Mtrs Exhaust pipe from Silencer

Genset Controller:

1. Microprocessor based genset monitoring, metering and control

system with full graphics LCD display for easy front panel access.

2. AMF relay, manual and remote start / stop modes for 1-ph & 3-ph

3. Backlit and full graphics display with power saving feature

4. Engine parameter monitoring -Lube oil pressure, Engine coolant

temperature, Fuel level, Battery voltage, Engine running hours

5. AC Alternator parameter monitoring -Voltage L-N & L_L, Current,

kW, kVA (Phase & Total), Frequency, kWH, PF

6. Genset Protection: Engine: Low lube oil pressure, High coolant

temperature, Battery High/Low Volts, Fail to Start, Sensor failure,

Low fuel level, Overspeed AC Alternator: Over/Under Voltage,

Over/Under, Frequency, Loss of AC sensing, Over frequency, Over

Current, kW Overload, Unbalancing load

7. Maintenance notification based on Engine Run Hour & due date

8.Communication: USB port, RS485, CAN

9.30-50 Event logs

Acoustic Enclosure: 1. Specially designed to meet stringent

MOEF/CPCB IV+ norms2. Weatherproof, powder coated Acoustic

enclosure for DG set for sound attenuation fabricated from 1.2 mm /

1.6 mm CRCA sheet steel (structure) with side wall fabricated from

1.2mm /1.6 mm CRCA sheet and filled with PU Foam/Rockwood for

Fire retardant acoustic and for better safety3. Designed to operate

in extreme climatic conditions in temperatures ranging from -10 deg

to 55 deg without any external aid4. Fabricated base frame with

AVM pads.5. Noise level is less than 75 db (A) at a distance of 1

Mtrs as per CPCB norms, complete in all respect.

9 Supplying and laying MS pipe for horizontal and vertical run of

Exhaust piping with asbestos lagging and Al sheet cladding along

with clamps, MS Supports & all arrangments supports above 3 mtr

MR etc from the roof of DG Set as required. Mtr 30 9,973.00 2,99,190.00

10 Supply of Hand pump to pump the HSD fuel from barrels to

MR the DG tank with flexible hose pipes etc as required. Each 1 10,452.00 10,452.00

11 Constrution of DG foundation with M-20 Grade RCC(1:1.5:3) of size

6.8m(L)X3m(W)X0.5m(H) with provisioning of 110 PVC piping for

Cable laying with all other required accessories as per the direction

MR of Engineering Incharge. Ls 1 54,698.00 54,698.00

12 11kV/0.433kV ONAN WITH ON LOAD TAP CHANGER WITH

BUCHHOLZ, OTI , WTI RELAYs

Design, Manufacture, Supply at site, inspection of Consultant's/

client at Factory at your cost, Receiving, unloading & shifting to

Sub-Station, storing, inspection of Consultant's/client at site,

handling, installing in correct aligned position, on existing

foundation, testing and commissioning of 500kVA continuous duty

cycle, 11kV/0.433kV, 3 phase, 50Hz, Dyn-11 vector group, step

down, outdoor type, copper wound, ONAN type transformers with

On Load Tap changer & with all fixing accessories including

complete as per specifications. Tap changing range shall be +5%

to -10% in steps of 2.5%. Class 'A' of Thermal insulation Suitable

for Ambient temperature 45º C. Maximum winding temprature 105º

The Following Fittings Shall Be provided with all required

accessories:- Rating & Terminal Marking Plate, Earthing Terminals,

Lifting Lugs For Main Tank & Top Cover, Filter Valve , Drain Cum

Sampling Valve, Thermometer Pocket, Dial Type Oil Temperature

Indicator, Air Release Plug, Silica Gel Breather, oil conservator,

Explosion Vent, Inspection Cover, Arcing Horn, Radiators Mounted

on Tank, 4 Nos. bi-directional Rollers, First Filling of Transformer Oil

as per IS:335, Magnetic Oil Level Gauge, Buchholz Relay, Oil

Temperature Indicator, Winding Temperature Indicator, Marshalling

Box, Epoxy Bushing, PU Paints, Palm, LV Bus Bar, Radiator Valves,

Cable Box on LT side & Cable Box on HT side. Transformer shall

Compliance to IS:1180 Level-1 & IS:2026 all parts latest as on date

whichever is higher. complete with all accessories

The transformer shall be delivered along with after complete factory

tests and temprature rise test, Operational & Maintenance manual

and test certificate of unconditional guaranteed against

manufacturing defects for a period of 18 months from the date of

Item No:- 3.8.5 Transformer as Described Above Set 1

13 SITC of Cubicle type or Pole Mounted(with cantilever provisioning

on DP Structure with Iso, LA & AB Switch appropiate ratings as

required) type 11KV HTCT Metering, HT cabling, inddor and

MR outdoor End terminations. LS 1 14,50,000.00 14,50,000.00

14 LT Kiosk Panel

Incoming - 800 Amp TPN ACB, 60 kA (Icu=Ics) , with

Microprocessor based O/L, E/F, S/C Relay, Complete with Digital

type Multifunctional Meter (V,A,PF,KWH,KVA & KW ) with CTs and

control MCB, phase indicating lamps LED type, On/Trip indications.

Four pole SPD class-B at LT incoming breaker

Note- Final rating & various parameter of Equipments, in addition to

the specified above shall be selected on the bases of ambient

conditions at site, client specific requirements, standards specified

in the tender, requirement for the NOC from various statutory

authorities, CPWD guidelines & as per detail designed stage

MR calculations. Each 1 5,33,552.00 5,33,552.00

Project Name:- Construction of Building Projects for The Institute of Chartered Accountantsof India (ICAI) Bhawan at Raipur

BOQ EV CHARGING STATION WORKS

Unit Rate Amount

Sl No. Description Unit Qty MARKET MARKET

Code DSR 2025 DSR 2025

EV Chaging Point

Supply, Installtion, testing and commisioning of Power : 7 kW, Input power supply:

1phase 230 +10% Volt, output supply: 230 Volt AC, Frequency:50 Hz +/-3%,

Operational temperature range : -25 to 55 degree C (outdoor), -5 to 55 degree

C(Indoor)., RH upto 95%, Charging Device as per IS-17017-22-1 EV-EVSE

Communication: as per relevant IS Codes, Bluetooth Low Energy, one Charge

Point Plug/ Socket as per IS- 60309 and IS-17017-2, Vehicle Inlet/ Connector As

per EV manufacturer, suitable for 2 Wheelers and 4 wheelers. Indoor use: at least

IP41; Outdoor use: at least IP44. Mechanical Strength :protection of the external

enclosure against mechanical impact shall be IK08 according to IEC

62262.O/L,S/C protection. Insulation Resistance > 1 M Ω. Cable Length: 7.5 m.

RCD having a rated residual operating current not exceeding 30 mA; Separate

RCD for multiple outputs. Telecommunication port of the EV supply equipment

Item No according to IS 13252 (Part 1) : 2010. OCPP(Open charge point protocol) 1.6J

15.1.1 (DSR upgradable to ocpp 2.0. Device Should follow 17017 series of IS codes in general

2025) and the installation of the system shall comply with relevent IS Codes Set 19 23,385.00 4,44,315.00

2 EV Chaging Panel

One (1) Incomer - 200 Amp, 36 KA, TPN MCCB , One(1) set of – 200/5A , 15VA ,

CL 1.0, CT with 3 Nos Phase indicating lamps with control fuse/ MCB Digital

Voltmeter and Ammeter with selector switch .(with required other accesories.)

Busbar - 300 Amp Al busbar suitable for operation at 415 Volt, 50 Hz, 3 Phase

Twelve(20) - Outgoing Feeders for (19 Nos EV Charger & 1nos spares) each

One (1) -32A TPN 10KA MCB with other required accesories.

One Set ON/OFF Indicating lamp with control fuse/ MCB with required other

Market Price PANEL AS ABOVE Set 1 188198 1,88,198.00

Project Name:- Construction of Building Projects for The Institute of Chartered Accountantsof India (ICAI) Bhawan at Raipur

Sl. No. DSR 2025 Description Unit Qty. Unit Rate Amount

PASSENGER LIFT - 13PAX

Supplying, Installation, Testing & Commissioning of

following capacity passenger Machine room less

(MRL) lift with regenerative drive as per CPWD

General Specification for Electrical Works (Part-III Lift

& Escalator) 2003, BIS Codes, NBC 2016 as

amended upto date having provision for barrier free

access as per Harmonised Guidelines & Standards for

Universal Accessibility in India - 2021 of MoHUA,

serving different floors in the lift shaft as per detailed

specifications enclosed and as under including all

other equipment and accessories complete as

(i) Speed-1 MPS

(ii) Floors-5 (G+4)

(iii) Travel -17 Meters (approx.)

(iv) Stops & opening- 5 stops and 5 openings

(v) Controller: A.C. variable voltage & variable

(vi) Automatic rescue device (ARD) complete with dry

maintenance free batteries as required.

vii) Operation: Microprocessor based single automatic

push button/simplex selective collective/duplex

collective selective with/without attendant

(viii) Power-415 Volts+10%, 3 phase, 50 Hz, 4 wires

(ix) Car Enclosure: Stainless steel scratch proof

(Moon Rock/Honeycomb/ Hairline Finish) on all sides

and stainless steel decorative ceiling with fans (indirect

throw) and LED fitting.

(x) The car flooring should be smooth and antiskid as

21.1 approved by engineer-in-charge.

Project Name:- Construction of Building Projects for The Institute of Chartered Accountantsof India (ICAI) Bhawan at Raipur

Description Unit Qty.

No. DSR2025 Unit Rate Amount

SupplyingPV Installation, Testing and Commissioning of on-grid Solar 0 0.00

Photovoltaic Power Plant conforming to various applicable standards BIS,

IEC, MNRE guidelines, the Central Electricity Authority Regulations and

CPWD Specifications as amended up to date, consisting of Mono/Poly

Crystalline silicon solar cells module, net metering facility, necessary

control, protections, earthing, cabling, mounting structure, junction boxes,

power conditioning units, Real time online web interfaced Data Monitoring

System, Distribution panels, grid connecting arrangement, conduits,

pipes, cable trays and other accessories etc. as required.

a) High Energy Efficiency Solar Photovoltaic Module of capacity 330 Wp

or above, manufactured in India, conforming to IS 14286/IEC 61215,

IS/IEC 61730- Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic

Module conversion efficiency shall not be less than

23% at STC with temperature coefficient of Pmax

better than -0.30% per 0C. PV modules used in solar

power plants/ systems must be warranted for their

output peak watt capacity, which should not be less

than 90% at the end of 10 years and 80% at the end of

25 years. Solar Modules shall be designed to operate

in relative humidity upto 100% with temperature

between -10 0C and +85 0C. Further, each PV module

used in any solar power project must have Radio

frequency identification tag with information such as

name of manufacturer, month and year of

manufacturing, country of origin (separately for Solar

cell and module), I-V curve, Unique Serial No and

Model No of the module, Wattage, Im, Vm and FF, name of test lab

issuing IEC certificate. b)Power Conditioning Unit (PCU) of 350-800 V DC

Input voltage range and 415 V AC, three phase, 4

wire, 50Hz +/- 2.5 Hz, output voltage suitable to

generate AC with a variation of 10% at nominal

voltage. Power with efficiency not less than 97%, total

17.1 harmonic distortion less than 3% and suitable for KW 20.00 54,280.00 10,85,600.00

Project Name:- Construction of Building Projects for The Institute of Chartered Accountantsof India (ICAI) Bhawan at Raipur

BOQ FOR FIRE PROTECTION SYSTEM

Unit Rate Amount

Sl No. Description Unit Qty MARKET

Code DSR 2022 DSR 2022 MARKET RATE

FIRE PUMPS & ALLIED WORKS

1 Supply, Installation, testing and commissioning of Electrical motor

driven Centrifugal pump set for fire fighting Hydrant & Sprinkler

system consisting of the following :

a) Horizontal Centrifugal single stage pump. End suction, top

discharge with all accessories capacity 2280 lpm at 70 m head driven

by electric motor 415 volts, 3 phase 50 Hz, AC supply of 60HP or of

suitable HP capacity for manual/automatic operation with CI casing,

standard fitting, CS diffusers, bronze impeller (dynamically balanced)

and SS (304) Shaft with mechanical seal.

b) The installation shall be complete with flexible coupling and

coupling guard, 150 mm dial pressure gauge of 0-16 kg/cm2 range

with gun metal shut off cock on delivery side as required.

c) Squirrel cage induction motor, TEFC, synchronous speed 3000

RPM, suitable for operation with IP 55 protection for enclosure,

horizontal foot mounted type with Class-'F' insulation, conforming to

d) Erected on provided suitable size cement concrete foundation duly

plastered with anti vibration pads with perfect aligning, proper

levelling complete pump set with accessories duly painted with two

coats of synthetic enamel paint of fire red colour over a coat of primer

Item no. - (ISC code 536 as per IS 2932 of 2003) complete(The pump should

18.1.5 (DSR be tested for bench mark at factory and test certificate shall be

2 Supplying, installation, testing and commissioning of main fire pump

(MFP/DP) suitable for water discharge of 2280 LPM at 70 m head

driven by 60 HP or suitable HP capacity diesel engine at required

working speed suitable for automatic operation and consisting of

following : (Diesel Engine Driven)

a) Horizontal type, single stage, centrifugal casing pump of cast iron

body & bronze impeller with stainless steel shaft(SS410 grade),

mechanical seal conforming to IS 1520.

b) Water cooled with radiator, diesel engine conforming to relevant IS

standard complete with auto starting mechanism, 12/24 volts DC

electric starting equipment with battery of required AH capacity with

necessary charger suitable to work on 230v, 50Hz AC supply, diesel

tank of minimum 150ltr capacity with first filling of diesel up to 100%

level with necessary piping with valves up to engine , exhaust pipe

extended up to 10 m outside pump house duly insulated with 50 mm

thick glass wool with 1.0 mm thick aluminium sheet cladding,

residential silencer, instruments and protection as per standard

specification, stop solenoid for auto stop in the event of fault with

audio indications etc. as required.

c) M.S. fabricated common base plate, coupling, coupling guard,

foundation bolts, Flexible rubber coupling etc. as required.

d) Erected on provided suitable size cement concrete foundation duly

plastered with anti vibration pads with perfect aligning, proper

levelling complete pump set with engine assembly and accessories

duly painted with two coats of synthetic enamel paint of fire red colour

Item no. - over a coat of primer (ISC code 536 as per IS 2932 of 2003)

18.2.5 (DSR complete.

3 Supply, Installation, testing and commissioning of horizontal single

stage Jockey pump of capacity 180 lpm at 70 m driven by electric

motor 415 volts, 3 phase 50 Hz, AC supply of 5HP or of suitable HP

capacity for manual/automatic operation and consisting of following.

a) Horizontal/vertical type, multi stage, centrifugal casing pump of

cast iron body & bronze impeller with stainless steel shaft (SS410

grade), mechanical seal conforming to IS 1520.

b) Squirrel cage induction motor, TEFC, synchronous speed 3000

RPM, suitable for operation with IP 55 protection for enclosure,

horizontal foot mounted type with Class-'F' insulation, conforming to

c) M.S. fabricated common base plate, coupling, coupling guard,

foundation bolts, Flexible rubber coupling etc. as required.

d) Erected on provided suitable size cement concrete foundation duly

plastered with anti vibration pads with perfect aligning, proper

levelling complete pump set with accessories duly painted with two

coats of synthetic enamel paint of fire red colour over a coat of primer

Item no. - (ISC code 536 as per IS 2932 of 2003) complete.

MCC cum control panel:

Designing, Supply, Transportation, Installation, Testing and

commissioning of system controller to control operation of main

electric fire pump, diesel pump, Pressurization pump, Terrace pump

in sequence as per specification consisting of relays, timers.

Sensors, annunciation window for fault indication, complete as per

specificationMakes: As per list of recommended brands.

400A, 50kA 4 Pole MCCB, Ics=100% Icu Rating Digital Voltmeter 0-

500V with selector switch Ammeter (0-400 A) with selector swtich &

LED type RYB phase indicating lamps, ON, OFF, trip indicating

lamps Set of Copper Bus Bar 800Amps

(Note : All outgoing feeders for pumps should have digital Ammeter

with selector switches, and LED type ON, OFF, trip indicating lamps)

200 Amp, 50kA TPN MCCB, Ics=100% Icu, with fully automatic

Star/Delta starter suitable for 75 hp pump with overload protection,

current sensing type single phase preventor complete with all

acceessories and internal wiring required for automatic operation,

selector switch for local/remote, auto/manual/OFF operation. - 1 sets

100 Amp, 50kA TPN MCCB, Ics=100% Icu, with Suitable HP fully

automatic Star/Delta starter with overload protection, current sensing

type single phase preventor complete with all acceessories and

internal wiring required for automatic operation, selector switch for

local/remote, auto/manual/OFF operation. - 1 sets

DIESEL ENGINE CONTROL

Control for diesel engine comprising - Automatic/Manual selctor

switch & 3 attempts starting device, timers and relays as required,

push buttons, start/stop in manual mode Indicating lamp for high/

Low Lub. Oil pressure, High Water Temp and Engine on indication

Battery charger suitbale for 12V/24 V DC with boost and trickle

Item no. - selector switch, 0-30 V DC volt meter, and 0-20 A DC Ammeter All

18.5.2 (DSR standard relays and accessories for automatic operation of diesel

2022) engine System Controller. Set 1.00 2,87,855.00 2,87,855.00

5 Supply, Fabricating, fixing, testing and commissioning of air cushion

tank (material IS 2062/2002) with SS air-release valve of approved

quality with S.S isolation valve, GM drain valve, gate valve, provision

for pressure switches, pressure gauge etc. Inside the pump house

including making inlet and outlet connection with MS pipe of required

length from discharge header to air cushion tank, fixing properly and

securing the same to the base etc. complete in all respect having

painting including two coats of approved paint over a coat of primer.

The tank shall be fabricated out of 8mm thick MS sheet shall be of

cylindrical shape with 300mm dia and 1.5m height. The tank shall be

installed on suitable vertical legs having M.S. plate of size 75mm x

75mm x 5mm at the bottom. The legs shall be grouted in Cement

concrete foundation. Flange connection shall be provided for

Item no. - connection with discharge header. The tank shall be tested at 25

18.20 (DSR kg/sq.cm before installation.

6 Supplying,Installation,testing and commissioning of electric motor

driven pressurization Terrace pump having discharge of 450 LPM at

35 MWC head complete with pump Set, Electric Motor suitable for

operation on 415V, 3ph, 50C/s A/C supply Base frame, 2 no.

Item no. - pressure switch, 1 no. pressure gsuges,2 nos. Butterfly valves, 1 no.

18.4.2 (DSR NRV . PCC foundation and foundation bolts

7 Supply,installation,testing and commissioning of Floor/Wall mounted

sectionalised, front operated top entry dust and vermin proof M.V

panel Boards suitable for operation at 415V, 3 phase, 4 wire, 50 Hz

distribution system fabricated out of 2.0 mm thick CRCA sheet ,

insulated busbar with heat shrinkable PVC sleeve, base frame,

complete with all accessories including interconnections, earth bus

etc as required comprising of One (1)- 63 Amp,10 KA,TPN (class-C)

MCB with 3 Nos phase indicating lamps with control fuse/MCB,

Digital Voltmeter with selector Switch. DOL starter with O/L and

Single Phasing Preventor Suitable for motor. ON/OFF indication

lamps, Auto manual switch and ON/OFF push button.

8 Supply, Providing & fixing 150 mm dial type Pressure gauge of (0-

16kg/cm2) range with gun metal shut off cock etc. duly calibrated

before installation in MKS and FPS units and fixing the same where

required as directed including all fittings, short piece, nipples, elbows

Item no. - testing the joints etc. All complete. (Quantity of this item will be

16.8 (DSR payable only where it has not been included in the relevant composite

9 Supply, Providing & fixing Pressure Switch the most commonly used

fluid control components of Aluminium enclosure with storage

temperature 40 to 180°F (-40 to 82°C) along with ambient

temperature 0 to 160°F (-18 to 71°C),set point shifts less than 1% of

range for a 50°F (28°C) ambient temperature change. Unit will

operate down to -40°F (-40°C) but with reduced repeatability.

Maximum media temperature 200°F (93°C), Shock Set point repeats

after 50 G, 10 millisecond duration. Switch output One SPDT

Item no. - including seven electrical terminations; Refer to 'How to Order' and

18.22 (DSR vibration set point repeats after 10 G, 5-500 CPS.

10 Supply ,installation, testing & Commissioning of orifice plate made of

6mm thick stainless steel with orifice of required size in between

Item no. - flame and landing valve of external and internal hydrant to reduce

18.13 (DSR pressure to working pressure of 3.5 kg/sq. cm complete as required.

11 Providing and fixing CI double flanges suction strainer (PN 1.0) “Y”

type including, nuts, bolts and 3mm thick rubber insertion complete.

a) Item no. - 200mm dia

12 Providing and fixing butterfly valves, wafer end type class PN

1.6 as per IS: 13095-1991 or BS: 5155, including necessary nuts,

bolts, gaskets etc. complete (without gear box) (Discharge Side)

a) Item no. - 200mm dia

b) Item no. - 150mm dia

c) Item no. - 100mm dia

d) Item no. - 50mm dia

13 Providing & Fixing of CI gate Valve as per IS : 14846 (PN 1.0 Rating

for suction side of the pumps ) and rising spindle type with flanges ,

bolts , nuts , washers , gaskets etc.

a) Item no. - 200 mm dia

b) Item no. - 150 mm dia

c) Item no. - 100mm dia

d) Item no. - 80 mm dia

14 Supply, installation, testing and commissioning of approved Cast

Iron Non-Return Valves including making flanged joints by providing

necessary nuts, bolts, gaskets etc.

a) Item no. - 200 mm dia

b) Item no. - 150 mm dia

c) Item no. - 100 mm dia

15 Supply, installation, testing & commissioning heavy class MS suction

& delivery headers of required length conforming to IS: 1239 up to

150 mm dia pipes and IS:3589 with 6.35 mm thick with welded joints

standard MS Fittings and with end flange connections having inlet &

outlet flanged connections including supports from wall, floors &

ceiling complete as required. Cost should be inclusive of all supports

/ clamps / brackets, anchor fastener, flexible expansion bellows etc.

a) Item no. - 25 mm dia

b) Item no. - 50 mm dia

c) Item no. - 80 mm dia

d) Item no. - 100 mm dia

e) Item no. - 150 mm dia

f) Item no. - 200 mm dia

16 Providing and fixing exhaust, Diesel engine driven pump exhaust M.

S. pipe class ’B’ of suitable dia (150mm dia) for the engine including

fitting like flanges, bends, reducers, etc. The pipe shall be provided

with 12 mm thick supercera ceramic fibre rope, 21 gauge, necessary

excavation, fixing of silencer connections at engine exhaust,

necessary supports, back filling, cutting and making good, bird proof

and weather proof flap complete in all respect as directed.

17 Providing and installation of GM Ball Valve, IS-318 LTB-2 SS Stem

AISI 410, Ball SS 304/CF8, Teflon gland packing, screwed female

threads to IS-554,

18 Supply, installation, testing and commissioning of Fire Brigade inlet

connection with provision for Four male instantaneous coupling

fabricated out of 150 mm dia. approved make heavy class MS pipe

with non-return valve, Butterfly valve for fire fighting system including

making connection by providing necessary piping & fittings to the fire

storage tank, fire fighting wet riser, sprinkler system painting the

same with 3 coats of enamel paint over a coat of Zinc Chromate

primer all complete as per drawings, specifications.

a) Item no. - Four way

19 Supply, installation, testing and commissioning of following sizes of

PVC sheathed XLPE insulated Aluminium Copper conductor/

power/control armoured cables of 1100V grade on surface of wall or

in existing cable trays with fixing hardware etc. as required.

Aluminium Conductor armoured cables:

Cable Termination :

20 Supply & making end termination with brass Double compression

glands for the following XLPE insulated PVC sheathed 1100 V grade

cable including cost of crimping lugs/ ferrules, compression glands,

solder, cable sockets, insulation tape etc. complete as reqd.

Suitable for aluminium conductor armoured cables:

a) Item no. - 3.5 x 120 Sq mm

b) Item no. - 3.5 x 70Sq mm

21 Supply, installation, testing & commissioning of following size G.I.

Strip/G.I. wire clamped to existing cable tray, wall for

system/equipment earthing complete as required including

interconnection etc.

a) Item no. - 25mm G.I Strip

b) Item no. - 6 SWG . G.I wire

External Piping (Hyd + Spk) - Underground / above ground Pipes

22 Supply, installation, testing & commissioning of MS pipe

(IS:1239/IS:3589) heavy class including cutting, screwing, welding

etc. complete with fitting viz. tees elbow, bends, flanges, reducers

etc. including providing anti-corrosive treatment (coating and