CWE/FZR- /2022-23 Provn of boundary wall from pillar CBF near CP-5 post No 2 to sewage pump No 11 and Special repair to bldg No P-91 (OTM Accn) of Raj Rif under GE (West) Ferozepur cant

Amount

Surface excavation in soft/loose soil not exceeding 30 cm deep and averaging 15 cm deep and getting out, complete all as specified.

Excavation in trenches in hard/dense soil not exceeding 1.5 meter wide and not exceeding 1.5 meter deep for laying of cable, pole foundation, etc including taking out old brick cable protection cover and getting out forming bottom surface to required gradient complete all as specified and directed.

M&L Cement concrete (1:4:8) type D2 40mm graded agg in foundations, filling and mass concrete complete all as specified and directed

M&L for TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified and direceted.

All as per Item No 4 above but 5mm dia and over upto and including 10 mm dia in stirrups, spacers and binders complete all as specified & directed.

M&L Formwork (rough finished surfaces of concrete flat) to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to batter complete all as directed by Engr-in-Charge

M&L Formwork (rough finished surfaces of concrete Square, rectangular or polygonal) to sides of pillars, posts, struts, piers, columns and stanchions complete all as directed by Engr-in-Charge

M&L Formwork rough finished to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as directed by Engr-in-Charge

M&L Reinforcement cement concrete (Design mixed M-25) using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified.

M&L Reinforcement cement concrete (Design mixed M-25) using 20mm graded stone aggregate as in Columns, pillers, piers, post & struts, complete all as specified.

M&L Reinforcement cement concrete M-25 design mix concrete using 20mm graded aggregate as in foundations, including rafts, footings, foundation beams, Plinth beam, bases of columns etc, complete all as specified.

M&L for Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified.

Material and labour rendering 15 mm thick cement plaster in CM 1:4 on other than fair faces of brick/concrete work surfaces complete all as specified.

M&L Preparation of new plastered surfaces of walls etc and applying two coats of cement base paint over a coat of primer, complete all as specified.

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

S&F rolled mild steel structural work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165

M&L Painting to new or previously untreated steel surfaces of any description, over 10cm width or girth two coats with synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified.

S&F 110 mm bore PVC (SWR) pipes single socked in any length with rubber ring joints fixed to wall and floor including fittings complete all as directed

Returning, filling in, earth including spreading, leveling watering and well ramming in layers each not exceeding 25cm thick each layer, complete all as specified and directed.

Removal of surplus soil to a distance not exc. 50 meter and depositing where directed at a level not exc. 1.5 meter above the starting point complete all as specified and directed.

Demolition of reinforced cement concrete as in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas, shelves, over head tank and similar suspended work and removing debris outside MD land complete all as directed by E-in-charge.

Demolition of PCC of any description and in any position not otherwise specifically provided for complete all as specified.

Dismantling of brick work built in cement mortar of any specification and in any position complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar beding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

Taking down cement plaster of any description on brick or stone walls etc. including raking out joints, hackinng for key, scrubbinng down with water, etc. complete all as specified.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required, complete all as specified.

Taking down shutters of any description exc 1.00 sqm area and not exc 2.00 Sqm each and refixing in the same opening complete all as directed.

Dismantling structural steel work including door, gates, shutters but excluding framed truss etc complete all as specified.

Dismantling brick tiles or terracing tiles laid in single layer on roofs jointed and pointed in cement mortar complete all as specified.

Demolition of mud phuska in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and directed.

M&L for 80 mm thick average consolidated thickness,mud phuska on flat roofs including 25 mm thick mud plaster complete all as specified and directed.

Rendering/plastering, 10mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, surfaces finished even and smooth without using extra cement with WPC complete all as specified. Note:- (WPC will be measured and paid separately)

M&L for applying tack coat of industrial bitumen 85/25 at the rate of 1.20 kg per sqm including cleaning surfaces complete all as specified and directed.

S&F 150 micron polythene film including preparation of roof surfaces complete all as specified.

M&L for 40 mm thick brick tiles laid on mud mortar and joints grouted flush in cement mortar (1:3) mixed with 5 % of crude oil by weight of cement on mud phuska and pointed flush as work proceeds complete all as specified and directed.

M&L except tiles for 40 mm thick brick tiles laid on mud mortar and joints grouted flush in cement mortar (1:3) mixed with 5 % of crude oil by weight of cement on mud phuska and pointed flush as work proceeds complete all as specified and directed. Note :- Old brick tiles retreived by dismantling of treatment vide item No 9 above to be reused.

M&L Flush pointing to roof tiles laid flat in cement mortar (1:3), complete all as specified.

M&L for Taking down wooden/steel chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Square metre each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts, making good jambs with plaster in CM (1:4) to match with existing finish, complete all as specified.

M&L for Taking down wooden/steel chowkhats or frames with shutters (without taking off shutters from the frames) of size exceeding 1.50 Square metre and not exceeding 4.00 Square metre each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts, making good jambs with plaster in CM (1:4) to match with existing finish, complete all as specified.

Taking down shutters of any description ( window /doors/Ventilators) of size exceeding 1.00 Square metre and not exceeding 2.00 Square metre, complete all as specified.

Taking up or down 20mm steel tubing and connections including cleaning for refixing or removal to store complete all as directed.

Taking up or down 15mm steel tubing and connections including cleeaning for refixing or removal to store complete all as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc.Laid, bedded and pointed in any mortar.

M&L RCC 1:2:4 type B1 using 20mm graded aggregate as in Precast cover slab , shelves and similar articles and setting in cm (1:6) complete with joints to match the surface, complete all as directed.

M&L for Cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in plinth protection, 50mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints complete all as directed by Engr-in-Charge and as specified.

M & L PCC 1:5:10 type E-2 (40mm graded aggt) as in foundation filling & mass concrete complete all as specified.

Material and labour rendering 15 mm thick cement plaster in CM 1:4 on other than fair faces of brick/concrete work surfaces mixed with integral water proofing compound all as per manufacturer's instruction and as specified. Note: (i) WPC shall be measured and paid for separately as 'Supply only'.

M&L for Rendering 15 mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

M/L rendering 5mm thick in CM 1:3 on fair faces of concrete finished even and fair in ceilings, complete all as specified.

Supply only liquid integral water proofing compound, complete all as specified.

M&L for special treatment of sunken portion of WCs and Bath room as per following stages:- Stage 1 :- Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc . Stage 2:- Providing 10mm thick plaster in CM 1:4 with chemical of Dr. Fixit Pidicrete URP/SIKA/plaster seal of STP Ltd or equivalent Stage 3:- Applying Dr Fixit Primseal primer or STP Ltd(and allow to dry for 8 hours) under touch dry condition Stage 4:- Applying two coats of water proofing of Dr Fixit Pidicrete for the sunken portion of toilets/bathrooms (The surface after painting one coats shall be allowed to dry of 6 hours before next coats) all as per manufactutrer instruction Stage 5:-Again rendering 10mm thick in CM 1:4 mixed with Dr Fixit Pidicrete URP or plaster seal of STP Ltd. Stage 6:- All CI joints shall filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr Fixit pidicrete URP. Stage 7:- Making holes in wall and fixing 600mm long 40mm dia GI spout for draining the surplus water if any.

M&L for preparation of newly plastered surfaces of wall and applying two coats of white wash complete all as specified and directed.

M&L for preparation of old surfaces of wall and applying one coat of white wash complete all as specified and directed.

M & L for complete removal of existing treatment over wall and applying two coats of distemper oil emulsion over 2mm thick wall care putty complete all as directed.

M&L for preparing newly plastered surfaces of wall and applying two coats of distemper oil emulsion over 2mm thick wall care putty of any shade on walls surfaces complete all as directed.

M&L for preparation of newly plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for preparation of old surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for factory made box type window with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter steel handle and with glazing bars dovetailedor welded and with one shop coat of zinc chromate primer complete all as directed and shown on Drawing No CEJZ/TD-1019/08 & CEJZ/TD-1020/08.

M&L for factory made box type window with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter steel handle and with without glazing bars both dovetailedor welded and with one shop coat of zinc chromate primer complete all as directed and shown on Drawing No CEJZ/TD-1019/08 & CEJZ/TD-1020/08.

M&L for factory made steel ventilator side/top hung with glazing bars dovetailed or welded and with one shop coat of zink chromate primer complete all as specified and shown on Drawing No CEJZ/TD-1019/08 & CEJZ/TD-1020/08.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified.

S&F 3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads, in squares n.exc 0.50 Sqm in each pane complete all as specified.

S&F 3mm thick, frosted sheet glass ordinary quality and glazing, with oil putty or with wooden beads, in squares n.exc 0.50 Sqm in each pane complete all as specified.

S&F Factory made pressed steel frames made of 1.25 mm thick MS sheet of profile 125 mm X 60 mm for door and window frames with one or more rebates including lock strike plate, shock absorber, 20 mm dia 60 mm long MS conduit for housing of a drop bolt,hinges, hold fasts/lugs etc, treating of internal surfaces of chowkhats with coal tar or black paint including hold fasts/lugs etc complete all as specified.

S&F Factory made pressed steel frames made of 1.25 mm thick MS sheet of profile 105 mm X 60 mm for door and window frames with one or more rebates including lock strike plate, shock absorber, 20 mm dia 60 mm long MS conduit for housing of a drop bolt,hinges, hold fasts/lugs etc, treating of internal surfaces of chowkhats with coal tar or black paint including hold fasts/lugs etc complete all as specified.

S&F Factory made solid PVC door frame (having density not less than 600 kg/cum) of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube, complete all as specified in MES Schedule Part-I (2009),including making good jambs in CM(1:4) with finishes to match with existing, complete all as per specification & shown in drawing.

S&F Factory made solid panel PVC door shutter 30 mm thick (having density not less than 600 kg/cum) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site, complete all as per specification in MES Schedule Part-I (2009) & shown in drawing.

S&F Factory made, 35mm thick, 2nd class hard wood (Hollock), plain framed, panelled shutters, any number of panels, panels shall be of 9 mm thick B.W.P. commercial ply or 12mm thick BWR grade veneered particle board medium density, wood particle board with commercial face veneers, size of members as specified in clause 8.24(a) of MES Schedule Part-I section-8 complete all as specified.

S&F Factory made 35 mm thick,2nd class hard wood (Hollock), glazed and skeleton shutters open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass/gauge etc for doors, size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, complete all as specified.

S& F fixed in repairs aluminium alloy, anodized sliding door bolt with hasp and staple and fixing clips of sheet, cast or extruded section, and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed length of bolt 300 mm, complete all as specified.

S & F extruded aluminium anodised alloy handles, fabricated type, size of handle 150 mm complete all as specified and directed

S&F aluminium ,anodized 200mm long barrel tower bolts of extruded section, complete all as specified and directed

All as per item No 72 herein before but 150mm in size.

S & F 100 mm size butt hinges of medium weight cold rolled mild steel, complete all as specified.

S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type B-21 complete all as specified and directed.

S& F in repair Mild steel 300mm long ordinary rat tail rod pattern springs including roller and roller plate, complete all as directed.

S & F Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified.

All as per item No 77 herein before but in repairs

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work, complete all as specified.

M&L for welding in running for thickness of metal to be welded n exc 6mm, complete all as specified.

M&L for cement concrete type B1 1:2:4 (20mm graded aggregate) as copings, kneelers, apex stones, bed plates, kerbs, edge of paver block, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed

M&L Non skid ceramic coloured tiles 7-8 mm thick (square or rectangular) area of eacch tile exc 0.06 sqm but not exc 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floors including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surfaces 300 X 200X 7 mm set and jonnted in cement slurry and pointed in white or colour, set and jonnted in cement slurry and pointed in white or colour cement to match including 10mm thick back coat in CM 1:4 complete all as specified and directed.

M&L Granite (of any type) tiles 20mm thick machine cut, bedded in 15mm thick screed bed in CM 1:6 and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types including complete all as specified and directed.

M& L for Machine cut kota stone slab flooring 20-25mm thick over cement over 15 mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including notching/nosing/easing complete all as directed.

All as per item No 85 herein before but in skirting including 10mm back coat in CM 1:4 complete all as directed.

S&F Galvanised steel water tubing, 20 mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors including cutting and making good, complete all as specified.

Re-fixing only, steel water tubing, 20mm bore and connections in new or old position using new fittings fixing to wall/ceiling or laid in floors, complete all as specified.

S&F Galvanised steel water tubing, 15 mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors including cutting and making good, complete all as specified.

Re-fixing only, steel water tubing, 15mm bore and connections in new or old position using new fittings fixing to wall/ceiling or laid in floors complete all as specified.

S&F in repairs fancy type bib tap of CP brass, 15mm bore screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

S&F in repairs stop valve/angle cock fancy type of 15 mm dia cast copper alloy chromium plated screwed down, high pressure, with crutch or butter fly handle long shank and cup (concealed type) screwed both ends for iron pipes or for unions, complete all as specified.

S&F in repairs CP 15 mm dia pillar taps, fancy type screwed down high pressure, with or with out lettered ‘Hot’ or ‘cold’ with long screwed shanks and fly nuts, complete all as specified.

S&F in repair for 100mm dia Cast iron Nahani trap with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F Wash hand basin, flat back 550x400mm vitreous china (white) including waste coupling, waste pipe , angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing as in repair complete all as specified.

S&F in repairs Vitreous china Squatting pan , "Orissa Pattern" size 580 X 440 mm , white with integeral foot rests ( excluding Flushing cisitern and flush pipes) fixed in repairs including concrete bedding with cast iron ‘P’ or ‘S’ Traps with connector pipes etc complete all as directed.

S&F steel water tubes, 40mm diameter medium grade galvanized, with all fitting and fixed to RCC walls complete and ceiling or laid in floors or in sunken portion as spout including making necessary hole for inseting spout and making good with cement mortar (1:1) complete all as directed

S&F in repair PVC syphonic action type low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, 32 mm PVC flush pipe and necessary fixing arrangements and connecting to water pipe, complete all as specified .

M&L in repair, 2nd class soft wood fillets, sectional area n.exc. 3 sqcm, rectangular in section, wrought finished, fixed with PVC rawl plug & steel screw complete all as specified.

S&F factory made PVC cup boards/ Shelf / Partition of required size consisting of panel of 18mm thick Celuka PVC Ply and for supporting the hold of Shelf/ Partition and shall provided 3edges in size 18mm x18mm as per required length. The front side of the edge visible in the front of the shelf/ Partition to be edge lipped by 18mm width x 1mm thick PVC sheet using solvent cement etc. complete as per direction of Engineer-in-charge, manufacturer's specificaton and drawing, complete all as specified.

S&F continuous (Piano) hinges mild steel, bright finish or Electro galvanized 25 mm wide flaps (when open), complete all as specified.

S&Fin repair 1000 Ltrs capacity Rotational rotational moulded polythene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including dismantling old unsv water tanks and removing to store complete all as directed

S&F in repair 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, complete all as directed

S & F in repairs 20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass ferrule, complete all as directed

S&F PVC (SWR) 110 mm bore bends of any radius, complete all as directed

S&F cast iron soil, waste and vent pipes of 75 mm bore in any length with or without ears with cement joints fixed to wall complete all as specified and directed.

S&F CI bends of 75 mm bore diminishing pieces or tapers including jointing with CM 1:3 and making good complete all as specified and directed

M&L for Tubular towel rail, of aluminium anodized 20mm dia, D type, 60cm long between flanges fixed to wall, complete all as directed

M&L for taking down shutter of any description, area n exc 1 Sqm each for repairing the steel windows in any position by replacing the projecting type hinges (Single pane) welding the new hinge and refixing the shutter including applying two coats of synthetic enamel paint over a coat of primer complete all as directed. .

M&L Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade over sand cushioning complete all as specified and directed.

M&L sand filling under floors or in foundations including watering and consolidation or under ground cable in trenches/existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable complete all as directed by Engieer-in-charge .

Supply and fixed in repairs mild steel curtain rod powder coated with fixing side brakets, end cup, rings 10 Nos per RM and fixed with PVC rawl plugs and steel screws complete all as specified and directed.

M&L for preparation of new wooden surafces of any description not otherwise described , over 10 cm width or girth , priming with a coat of pink primer and applyinng 2 coats of synthetic enamel paint of approved shade complete all as directed

M&L for preparation of old wooden surface of any description over 10 cm width or girth and applying one coat of synthetic enamel paint white or tinted complete all as directed.

M&L for preparation of old painted steel surface of any description , over 10 cm width or girth not otherwise described and applying one coat of synthitic enamel paint white or tinted all as directed.

Taking down carefully copper /aluminium point wiring (light, fan, socket or power) complete, fittings such as switches, ceiling roses, pendants, regulators sockets light fitting etc removing materials to store for keetping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as directed and specified

Taking down carefully unserviceable main switches and distribution boards with fuses/ MCB's (single phase or three phase) of any capacity all as specified and directed.

Taking down carefully old unserviceable sub main wiring including meters and making good disturbed surfaces and matching with existing complete all as directed and specified

M&L Point wiring complete with 1100 volts grade PVC insulated unsheathed FRLS cable of copper conductor, multi stranded of size 1.5 sqmm, single core, in and including existing rigid non-metallic PVC conealed conduit, with all accessories if require such as bends,reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks(for housing lamp holders and light fittings etc) and existing MS pressed steel / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire of size 1.5 sqmm unsheated stranded copper conductor with green PVC insulation connected to common earth dolly complete all as specified and directed for the followings :- (a) One light/fan/Bell Point controlled by one single pole one way switch.

(b) One socket outlet on the same board controlled by one single pole one way switch

(c) One 5 amps socket outlet independent controlled by one single pole 5 Amp switch.

All as per Item No 120 mentioned here-in- before but one three pin 15 Amps switch socket out let on the independent board with 2.5 Sq mm PVC insulated copper conductor and 2.5 Sqmm copper conductor for continuous earthing complete.

Supply & Fixing Switch piano flush type single pole one way 5/6 Amp complete all as directed.

Supply & Fixing Switch piano flush type 15 amps, single pole one way duly ISI marked, complete all as directed.

Supply & Fixing Socket outlet 2 in one , 5/6 Amps flush type ISI marked, complete all as directed.

Supply & Fixing Socket outlet, 2 in one 6 pin 5 and 15 Amps piano flush type ISI marked, complete all as directed.

Supply & Fixing ceiling rose, PVC/Polycarbonate, isolated three terminals, complete all as directed.

Supply & Fixing Lamp holder PVC/Polycarbonate, isolated with back plate suitable for batten fittings including 10W LED Bulb omplete all as specified and directed.

Supply & Fixing step type regulator Piano switch type (5 step) for ceiling fan 1200/1400 mm size 230 volts, 6 Amps, complete all as directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified.

M&L Cutting holes making good the distributed surface, grouting nuts for fixing of Exhaust fans complete all as specified and directed.

Supply & Fixing LED tube light fitting 20 Watts,4 feet long decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient 230V, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size, complete all as directed.

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series TPN DBs (Vertical type)fitted with ABS frame and 415 volts 200 Amps rated enameled bus bar 4 way dust and vermin proof ssuitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 volts 200 Amps rated bus bar,Neutral link,Earth bar and Din rail, 8 way dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified.

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 volts 200 Amps rated bus bar,Neutral link,Earth bar and Din rail, 4 way dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified.

Supply & Fixing MCCB 100 Amps, 415 volts, 16 KA, 4 Pole complete all as specified.

Supply & Fixing MCB, Single pole 240 V,6 - 32 Amps 10 KA 'B Series, complete all as specified.

Supply and fixing SPN 32 Amps rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) and 32 Amps current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified.

Supply & Fix in repair sub main wiring of 6 sqmm PVC insulated unsheathed FRLS cable multistranded copper conductor with earth wire of 6.0 sqmm PVC insulated unsheathed FRLS cable multistranded copper conductor including PVC conduit pipe 25 mm dia all as specified and directed. Note:-Two run of single core 6 sqmm cable and one run single core 6.0 sqmm cable for earth wire and including conduit pipe 25 mm dia shall measured as one length).

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. complete all as specified and directed.

M&L as in repair Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC ( 1:3:6 ) type C-2 using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate, excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009)

Supply, laying , jointing and testing of cable XLPE insulated, screened, PVC bedded ,galvanized steel strip or wire armoured heavy duty electric cable with multistranded aluminium conductor, 1100 volts grade, laid in trenches or duct or passing through pipe or fixed to poles walls of size 50 Sqmm 3.5 core confirming to IS : 7098-1985 laid in trenches or passing through pipes/ducts or fixed to walls/poles complete all as specified and directed.

S&F Galvanized steel tube 40 mm dia light grade For protection of cable complete all as specified and as directed

M&L for Sand cushioning to under ground cable in trenches/existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable complete all as directed.

S&F cover to underground cable with one layer of bricks using sub class ‘B’ bricks (old size) laid flat across the cable complete all as specified. (Excavation and earth work measured separately).

Harmesh Kumar Sharma and Sons

Dee Kay EnterPrises

M/s Harkesh Kumar Bansal

HARBHAJAN SINGH KHARBANDA

M/s Surjit Singh and bros

M/S CHAWLA CONSTRUCTION COMPANY

S.R. Kaura and Company

shivam builders

Karan Engineers

M/S Pee Kay Builders

MS SUSHIL KUMAR CONTRACOR