SPECIAL REPAIR TO BLDG NO TR-02 AND TR-03 (OTM ACCN), SL/CH2A AND CH2B AND OTHER SANCTIONED WORKS AT UNDER AOR OF AGE B/R-I AT AKHNOOR UNDER GE (SOUTH) AKHNOOR

Amount

Demolition of cement concrete (unreinforced) concrete in ground floors and paving n-exc 15cm thickness ( below or above ground floors.) complete all as specified and as directed by engineer in charge.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by engineer in charge.

Dismantling of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlars facings, dressed stonework and precast concrete articles, complete all as specified and as directed by Engineer-In-Charge.

Plain cement concrete Nominal Mix (1:2:4) M-15, type B-0 (using 12.50mm graded crushed stone aggregate), nominal mix, 25mm thick, as in floors, finished even and smooth without using extra cement, complete all as specified and as directed by Engineer-In-Charge.

Machine cut kota stone slab, (minimum size shall be 550x550mm), flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, and including laid over screed bed or bedding layer of mortar 20mm thick in cement mortar 1:6, complete all as specified and as directed by Engineer-In-Charge.

Machine cut kota stone slab, (size shall in one length), 12mm thick, as in riser of steps, skirting, dado and pillar, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, and including laid over screed bed or back plastering layer of mortar 15mm thick in cement mortar 1:4, complete all as specified and as directed by Engineer-In-Charge.

M&L GI wire of 6mm dia including fixing with straining bolts and nuts with hook and ncessary PCC work in M-10, Nominal Mix type C-1 (1:3:6) using 20mm graded crushed stone aggregate, and necessary form work for mosquito net equal to length of barrack and 04 Nos line in each barrack shall be provided, complete all as specified and as directed by Engineer-In-Charge. Note:- Cost of required Nos of Gusset Plates of any thickness, nut & bolts, PCC work in notified mix , form work and other adjoining items required for completion of job shall be deemed to have been included in quoted rate and nothing extra shall be admissibe on this ground.

Brickwork with subclass ‘B’ bricks, old size bricks, straight or curved on plan exceeding 6.0mtrs mean radius built in cement mortar 1:6, complete all as specified and as directed by Engineer-In-Charge.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc, complete all as specified and as directed by Engineer-In-Charge.

Rendering 15mm thick on fair faces of brick work or concrete surfaces, in cement mortar 1:4, including mixing water proofing compound @ 3% by weight in cement, rendering is to be finished even and smooth (without using extra lime or cement), complete all as specified and as directed by Engineer-In-Charge. Note: Cost of water proofing compound shall deemed included in quoted rates.

Rendering 15mm thick, on any faces of brick or concrete surfaces, in cement mortar 1:6, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed by Engineer-In-Charge.

Rendering 10mm thick, on any faces of brick or concrete surfaces, in cement mortar 1:6, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed by Engineer-In-Charge.

Rendering 5mm thick on any type of surfaces, on ceiling, in cement mortar 1:3, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed by Engineer-In-Charge.

Rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, conforming to Fe 410-W (Gde- E- 250) quality-A, complete all as specified and as directed by Engineer-In-Charge.

Rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening, Fe 410-W (Gde-E-250) quality-B, complete all as specified.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 22.50cm but not exceeding 30.0cm long, dia of neck 5 to 10mm, complete all as specified and as directed by Engineer-In-Charge.

Mild steel work in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting including securing bolts; and similar work conforming to Fe 410-W (Gde- E- 250) quality-A,, complete all as specified and as directed by Engineer-In-Charge.

S&F in replacement of Rotational moulded polyethylene water storage tanks of 1000 liters capacity, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe, complete all as specified and as directed by Engineer-In-Charge.

Vitrified Ceramic tiles 10mm thick (square/ rectangular) polished, non-skid, area of each tiles not exceeding 0.36 Sqm but not exceeding 0.42 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, and including laid over screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6, complete all as specified and as directed.

Vitrified Ceramic tiles 10mm thick (square/ rectangular) polished, non-skid, area of each tiles not exceeding 0.36 Sqm but not exceeding 0.42 Sqm, set and fixing in skirting/ dado or any other vertical surfaces and pointed in white or coloured cement to match and including 10mm thick rendering in cement mortar 1:4, complete all as specified and as directed.

Non-skid, coloured, ceramic tiles 7 to 8 mm thick (square/ rectangular) (Designer Pattern) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including laid over screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6, complete all as specified and as directed by Engineer-In-Charge.

M&L for applying two coats of cement base paint on newly plastered surfaces of walls including preparation of new surfaces complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over one coat of chalk whitening, preparatory to distempering, after making surface smooth with 3mm thick birla white wall care putty, complete all as specified and as directed by Engineer-In-Charge.

Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sqm each, complete all as specified.

Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) area exceeding 1.50 Sqm but not exceeding 4.0 Sqm each, complete all as specified.

Glazed ceramic tiles in vertical surface/ dado, size 300x450mm/ 300x200mm, 6/7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match, the shade/ colour of tiles including 10mm thick rendering in cement mortar 1:4, complete all as specified and as directed by Engineer-In-Charge.

Solid PVC Door Frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specification and drawing, including making good to disturbed surface of walls, complete all as specified and as directed by Engineer-In-Charge.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Paneling of plain colour PVC sheet to be fitted in the mild steel frame welded/ sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing in SSR, complete all as specified and as directed by Engineer-In-Charge.

Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 Kg/mtr with comprising frame thereto like bottom rail & top rail section of as directed by Engr-in-Charge, including necessary joining cleats, including and fixing of 5.50mm thick plain glass sheet with rubber packing/ beading glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21 100mm long (2 Nos.) suitable handle (1 No.), fixing in repairs, complete all as specified and as directed by Engineer-In-Charge. Note : Cost of frame as directed, shutter, glass and other filling material in panels shall be deemed included in quoted rate

Anodised aluminium powder coated (minimum thickness of powder coating 50micron) openable door shutters with comprising bottom rail section of frame not less than 111.6x44.75 and 2.44mm thick, top rail section 105x44.45 and 2.20mm thick, lock rail 150x44.5 and 3.0mm thick, with door handle locking system (Godrej/ Link/ Harrison), shutters frame including necessary joining cleats, glazing clips, rubber neoprene packing, 150mm long handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc and fixing 5.50mm thick plain glass sheet with rubber packing/ beading, complete all as specified and as directed by Engineer-In-Charge. Note : Cost of door frame, shutter, glass and other filling material in panels shall be deemed included in quoted rate.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, , complete all as specified and as directed by Engineer-In-Charge.

Preparation of new or previously untreated wood or wooden surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed by Engineer-In-Charge.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10cm width or girth including and applying two coats of synthetic enamel paint over one coat of zinc chrome/ red oxide primer, complete all as specified and as directed by Engineer-In-Charge.

Aluminium alloy, anodised, sliding door bolt, size 250mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and as directed.

Aluminium anodised, barrel tower bolts of extruded Section, size 150mm long and fixed, complete all as specified and as directed by Engineer-In-Charge.

Mild steel spring for doors, 300mm, ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and as directed by Engineer-In-Charge.

Anodised aluminium powder coated grills of 6-8mm dia of wire and average width of aperture 75mm and fized with aluminiu wire of any pattern, complete all as specified and as directed by Engineer-In-Charge. Note: Weight of grill per square meter shall be decided by BOO for payments.

Cast iron body Door closer hydraulically regulated, designation No-3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

M&L for preparation of old surfaces of walls including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc including cornices, pilasters etc (plastered or unplastered surfaces) and applying one coat of Oil emulsion distemper (white/tined ) complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of old surfaces of walls including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc including cornices, pilasters etc (plastered or unplastered surfaces) and applying one coat of cement base paint, complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of old surfaces of walls including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc including cornices, pilasters etc (plastered or unplastered surfaces) and applying two coat of Oil emulsion distemper (white/tined ) complete all as specified and as directed by Engineer-in-Charge.

Plain cement concrete M-10(1:3:6), type C-1 (using 20mm graded crushed stone aggregate), 50mm thick, as in plinth protection and providing the joints throughout the thickness, filled with mastic filling comprising bitumen 85/25 grade and sand mixture 1:3 by weight, complete all as specified and as directed by Engineer-In-Charge.

Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 125x60mm, complete all as specified and as directed by Engineer-In-Charge.

PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in back filling of steel chowkhat single or double rebated or for fixing complete all as specified and directed.

Factory made, 35mm thick, second class hardwood, plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and as directed by Engineer-In-Charge.

Factory made, glazed and skeleton shutters in second class hardwood, 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and as directed by Engineer-In-Charge.

Factory made steel window, box type, using ERW hollow 'P' section, comprising double frame for and including gauged and glazed skeleton shutter with wire mesh and plain sheet glass 3.0mm thick, 4mm thick frosted glass, jointed internally and made with flat iron 40x4mm complete including grill/ guard bars of 8mm square bars fixed horizontally @100mm C/C including mild steel hinges, handles, tower bolts, stops, lugs etc, complete all as specified and as shown in drawing No- CEUZ/TD-1304, sheet No- 1/3 to 3/3 and as directed by Engineer-In-Charge. Note :- Cost of window shall include all members and spare parts as elaborated in the Drwaing and in the specifications and nothing shall be paid extra seperately.

Cutting holes in brick walls , Superficial area n exc 150 sqcm built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required, complete all as specified and as directed by Engineer-In-Charge.

Dismantling framed steel truss of size not exceeding 10m in span, complete all as specified and as directed by Engineer-In-Charge.

Vitreous China wash down water closet pan (pedestal pattern), white (including fixing bolts, flush pipe but excluding flushing cistern) and including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and making good to dismantled/ damaged floor in cement concrete M-15 (1:2:4), type B-1 (using 20mm graded crushed stone aggregates), fixing in repair, complete all as specified and as directed by Engineer-In-Charge.

Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white washing, complete all as specified and as directed.

Cleaning of blocked/ choked SGSW/ Cast Iron drain pipes/ sewer lines of any dia and any types, in horizontal or vertical position by rodding, from manholes to manholes and manholes end to septic tanks/ soakage wells, flushing with pressure jet of water/ sewage suction machine after taking out existing manholes covers and putting back manhole covers in original position after cleaning of lines including removing the sludge and other waste materials/ blockage in drain pipes, transport to outside of Unit/ Cantonment area and spreading bleaching powder on top of manholes covers of septic/ soakage pits or in the surrounding areas to make hygienically fit, complete all as specified and as directed by Engineer-In-Charge. Note: Cost of transportation of waste materials shall be deemed included in quoted rates.

Taking up or down steel tubing of 15mm bore pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed.

Tubes, 'medium grade' galvanised, 15mm bore, ISI marked, making concealed, with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, including cutting and chasing the any type of surfaces, complete all as specified and as directed.

Refixing old steel tubing galvanised, 15mm bore, making concealed, with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts and connections in new or old position (walls, ceiling, floors, etc.), complete all as specified and as directed.

Taking up or down steel tubing of 20mm bore pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed.

Tubes, 'medium grade' galvanised, 20mm bore, ISI marked, making concealed, with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, including cutting and chasing the any type of surfaces, complete all as specified and as directed.

Refixing old steel tubing galvanised, 20mm bore, making concealed, with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts and connections in new or old position (walls, ceiling, floors, etc.), complete all as specified and as directed.

Bib taps, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed.

Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore pipe, fixed in repairs, complete all as specified and as directed by Engineer-In-Charge.

Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 20mm bore pipe, fixed in repairs, complete all as specified and as directed by Engineer-In-Charge.

Angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore pipe, fixed in repairs, complete all as specified and as directed by Engineer-In-Charge.

Wall mixer with bend pipe for overhead shower with built-in non return valve, for hot and cold water, chromium plated, for 15mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge. Make: Cat Part No-F1014402 of Cera/ Jaquar/ Parko/ Hindware.

Centre hole basin mixture for hot and cold water, chromium plated, with round sport without pop up waste system for 15mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge. Make: Cat Part No-F1013451 of Cera/ Jaquar/ Parko/ Hindware.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed for 15mm bore pipe, fixed in repair, complete all as specified and as directed by Engineer-In-Charge.

PVC connections 15mm size with brass nuts of length 450mm fixed in repair, complete all as specified and as directed by Engineer-In-Charge.

PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, capacity 10.0 litres and making good to dismantled/ damaged floor/ surfaces, fixing in repair, complete all as specified and as directed.

Shower, chromium plated, with arm and round shower rose 125mm size, fancy type, fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Sinks with drainage board made of stainless steel 1.0mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Tubular towel rail, 20mm dia, D-type, 60cm long between flanges, brass chromium plated, fancy type, including end brackets, complete all as specified and as directed by Engineer-In-Charge.

Stainlees steel grating, chromium plated, size 125mm, heavy duty, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Plate rack (kitchen stand) stainless steel, size 760x910x230mm, thickness of stainless steel sheet not less than 0.80mm, weight not less than 8.00Kg each, fixing by means of electrical drill machine, fasteners and screws, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

M&L Cement concrete M-15, type B-1, 1:2:4 ( using 20mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded or chamfered angles and throating and necessary form work, all as specified.

Curtain rod, 20mm dia, mild steel, fancy type, any colour coated, pvc layered with fixing and including end knobs, fixing brackets, stops, round rings to hold the curtain, fixing in repairs with wall plugs and screws, complete all as specified and as directed by Engineer-In-Charge.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, cverall length of cover plate 150mm, fixed in floor, complete all as specified and as directed.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, complete all as specified and as directed by Engineer-In-Charge.

Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and as directed by Engineer-In-Charge.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and as directed by Engineer-In-Charge.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, complete all as specified and as directed by Engineer-In-Charge.

Anodised aluminium snap grid frame work for false ceiling, powder coated, comprising of aluminium Tee (weight of section not less than 280 gms/mtr) and aluminium angle (weight of section not less than 280 gms/mtr), grid size 605x605mm, including Hangers 6.0mm dia, galvanised iron (upto1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of galvanised iron flat 40x3 mm size 60mm long and expansion hold fasteners 12.50mm dia, 40mm long including Perforated particle board/ tiles for insulation and accoustic purposes, 600x600 mm in size and 12mm thick, fixed with frame work (any type) or on snap grid, complete all as specified and as directed by Engineer-In-Charge.

Providing and fixing ceiling board 4mm thick, designer, in ceiling fixed as per manufacturer’s instructions, including Aluminium snap grid frame work of main and tee (weight not less than 240gm/Rm), angle (weight not less than 217 gm/Rm), grid size 605x605mm, for false ceiling all as specified, and hangers 6mm dia, galvanised iron (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of galvanised iron wire of 4.0mm dia, length as required at site and expansion hold fasteners 12.50mm dia, 40mm long, complete all as specified and as directed by Engineer-In-Charge.

PVC waste pipe, 40mm bore with cup washers, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Vitreous China wash hand basin, white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32mm dia and waste coupling, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Precast reinforced cement concrete M-20(1:1.5:3), type A-1, (using 20mm graded crushed stone aggregate), nominal mix, as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs and similar articles with plain faces as specified in clause No- 4.11.16 of SSR Part-I (2009), set in cement mortar 1:4, complete all as specified and as directed by Engineer-In-Charge. Note : The descrption shall also deemed to have included the cost of TMT bars of 10mm dia and over all as per codal provisions as conforming to IS 456:2000 and necessary form work.

Providing and fixing World Squash Federation (WSF) approved Maple Hardwood Sports flooring-I grade MFMA stamped in size 20 mm x 57 mm/83 mm Tongue & Groove , kiln dried and treated for termites for Delhi climate . Pine wood sleepers of size 38mm x 63.5mm x1.22m installed at 230mm distance from centre to centre. The thickness of plywood shall be of 12mm thick. The sleepers anti termite and bugs. 8mm thick cohesion/cushion pads shall be placed under the wooden sleepers for extra resilience.The maple flooring will be finished with anti skid polyurethane finish & shall be laid on the IPS surface as vapour barrier. The maple floor should be un-finished sanded with 60 grit sand paper to leave a "nap" on the floor. Floor should not be sealed and polished. Game line shall be applied as per WSF standards.

Providing and fixing of Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of mild steel heavy duty both sie movement ( capacity to hold lift glass of 100-150Kgs) , other parts made of mild steel heavy duty and fixed, complete all as specified and as directed by Engineer-In-Charge.

Stainless steel door handles of 'H' type of 30mm dia and 18" size, complete all as specified and as directed by Engineer-In-Charge.

S&F Top patch made of stainless steel, complete all as per manufacurer's instructions, all as specified.

S&F Bottom patch made of stainless steel, complete all as per manufacurer's instructions, all as specified.

S&F Pivots of stainless steel for fixing of Top patches, complete all as per manufacurer's instructions, all as specified.

S&F Door lock of stainless steel and fixing on glass door, complete all as per manufacurer's instructions, all as specified.

Providing and fixing 12 mm thick toughened glass which will consists of rear 4 panel of 12 mm thick clear toughened glass with a door with 15mm fins. The total size of of the glass wall would be around 21 feet to 7 feet conssisting 4 panels , 4 fins and 1 door, included with the glass walls, fittings and bolts that are embedded for the glass fins. It is here to note that for installations of rear glass walls, clear area is required figured all sides grinding & polishing single door shutter having holes for fixing of door handles and cut out for fixing of top and bottom patches, The glass meets the specifications laid down by the World Squash Federation (WSF). as per Engr-in-Charge dirn and company profile and instructions thereon. Make : Saint-Gobain/Modi Guard/Triveni Float Glass) Note 1: Proper Handling of glass till the functionability of glass wall and door is assured by the GE and Engr-in-Charge. In case any defect is observed due to transportation or during installation process shall not bear any compensation from the Deptt and same shall be at the risk of firm and borne by the firm itself for the new glass of specified specification. Note 2 : International quality glass back wall shall be warranted for 5 years by the Manufacturer on their letter Head for any kind of defect noticed same shall be rectified or replaced without any cost to the Govt..

M&L Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors, complete all as specified and as directed by Engineer-In-Charge.

M&L epoxy hard plaster treatment for 3 walls ( Front & 2 sides) will consist of 12mm thick 2 layers , fibre reinforced , cement based and resin modified , marking lines in red colour and painting woth epoxy paint . Please note that the walls of the squash court should be cement plastered in proper level and devoid of any undulations & be in the right angle , complete all as specified and as directed by Engineer-In-Charge.

Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, conforming to Fe-410 (Gde-E-250) quality-B, complete all as specified and as directed by Engineer-In-Charge. Note :- Size and structural details of the member shall be as per Engr-in-Charge directions.

S&F 12mm thick plain acrylic sheet for cladding of existing steel columns by using clamps and other fixtures , complete all as specified and as directed by Engineer-In-Charge. Note : Make shall be among of the manufacturers as approved by HQ E-in-Cs Br or by Competent authority.

M&L preparation and applying two coats of yellow/white or of any other colour marking paint, straight line n exc10cm including border with black paint upto 25mm wide on either side to be done with aromatic PU coating. FK 666 as per manufactrur instructions. Note : The make shall be among of the manufacturer approved by E-in-Cs Br or by Competent authority.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc., complete all as specified and as directed by Engineer-In-Charge.

Point wiring for one light/ fan/ bell point controlled by one switch with 1.50 Sqmm, PVC insulated, unsheathed, single core, multi-stranded, copper conductor cable, 1100 Volts, using colour coding, drawn in and including non metallic medium grade rigid PVC conduit, fire resistance, ISI marked, 20mm dia including all accessories concealed by chasing/ cutting grooves in the surface of walls/ floors/ ceilings and making good the disturbed surface matching to existing descriptions/ specifications, with and including sunken type pressed steel/ welded mild steel terminal box 1.20mm thick coated with anti corrosive paint and with bakelite laminated sheet top cover 3.0mm thick and including FRLS PVC green insulated unsheathed 1.50 Sqmm copper earth continuity wire connected to earth dolly, complete all as specified and as directed by Engineer-In-Charge.

Description all as per serial item No- 100.00 here-in-before but for one 3- pin, 5-Amps, socket outlet on same board.

Description all as per serial item No- 100.00 here in before but for one 3-pin socket outlet 5-Amps on the independent board.

Point wiring for 3-pin, 15 Amps, switch socket combination on independent board with 2.50 Sqmm, PVC insulated, unsheathed, single core, multi-stranded, copper conductor cable, FRLS, 1100 Volts, using colour coding, drawn in and including non metallic medium grade rigid PVC conduit, fire resistance, ISI marked, 20mm dia including all accessories concealed by chasing/ cutting in the surface of walls/ floors/ ceilings and making good the disturbed surface matching to existing descriptions/ specifications, with and including sunken type pressed steel/ welded mild steel terminal box 1.20mm thick coated with anti corrosive paint and with bakelite laminated sheet top cover 3.0mm thick and including FRLS PVC green insulated unsheeathed 2.50 Sqmm copper earth continuity wire connected to earth dolly, complete all as specified and as directed by Engineer-In-Charge.

Switch piano, flush type, single pole, one way, 5 Amps, complete all as specified and as directed by Engineer-In-Charge.

Bell push switch, single pole, one way, flush type, 5-Amps, 240 volts, complete all as specified and as directed by Engineer-In-Charge.

Switch socket combination 2-in-1, 3-pin, 5 Amp flush type universal type, complete all as specified and as directed by Engineer-In-Charge.

Switch socket combination 2-in-1, 3-pin, 5 and 15 Amp flush type universal type, complete all as specified and as directed by Engineer-In-Charge.

T bulb curve, 12 Watt LED base B22 cool day light, complete all as specified and as directed by Engineer-In-Charge.

Stepped type (multi-steps) electronic regulator for ceiling fan 1200 mm, 240 volts, 100 Watts, single pole, including connecting, complete all as specified and as directed by Engineer-In-Charge.

Ceiling rose, three phase/ PVC/ polycarbonate, isolated body, complete all as specified and as directed by Engineer-In-Charge.

Lamp holder, PVC Polycarbonate type with back plate suitable for batten fittings, complete all as specified and as directed by Engineer-In-Charge.

Door bell, AC, 230 Volts, single pole, ding-dong type sound, completeall specified and as directed by Engineer-In-charge.

S & F Inverter LED Batten with opal diffuser, IP20, battery back-up & functioning as per product TDS, 20 Watt, complete with all accessories with twin core twisted flexible copper conductor cable with suitable size all as specified and directed. Havells cat part No- PRIDE PLUS INVERTER BATTEN LHEXACP7FN1W020 or Equivalent Makes in Crompton/Philips/Osram.

S&F in replacement of 4 feet highly engineered plastic body suitable with fully diffused diffuser for general lighting in areas. The luminaire should have a color consistency SDCM < 5, CRI > 80 and CCT of 6500K. The luminaire shall be compliant with IP20 and IK02 classification. Luminaire shall be designed to emit at least 2000 nominal lumens and an outstanding solution efficacy of atleast 100 lumen/watt and maximum system wattage of 20 Watts. The electronic driver used shall have a power factor >0.95 and THD <20% with 4 KV internal surge protection. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters and including suitable size and length of flexible copper wire and making the connection, complete all as specified and as directed by Engineer-In-Charge. Make : Bajaj cat part No BCLSB 20 WH Bajaj or Equivalent makes in Havells/Crompton. Warranty certficate for 2 years to be provided by Employee of Organization of Terittory.

LED tube light fitting, 10 watt, retrofit, 2-feet long, indoor decorative aluminium extruded LED battens, including LED lamp 10 Watt and connecting up with twin core twisted flexible copper conductor cable of suitable size, complete all as specified and as directed by Engineer-In-Charge. Make: Havells cat part No- Lumi Line Plus BS10WLED865SPCSS or equivalent in Crompton/Philips/Bajaj.

Sub main wiring (concealed conduits to surfaces) for circuits/ submain wiring alongwith earth wire with two run of 6.0 Sqmm of fire resistance, PVC insulated copper conductor, single core cable, multi-stranded, FRLS, ISI marked, 1100 Volts grade and one run of 6 Sqmm, FRLS, PVC insulated copper conductor, single core cable, multi stranded, ISI marked, 1100 Volts grade as earth wire connected to earth terminal, drawn in and including non metallic medium grade rigid PVC conduit, fire resistance, ISI marked, 25mm dia including all accessories concealed by chasing/ cutting grooves in the surface of walls/ floors/ ceilings and making good the disturbed surface matching to existing descriptions/ specifications, complete all as specified and as directed by Engineer-In-Charge.

S&F SAUCER NEXTGEN HIGHBAY Next generation, energy saving, environment friendly & robust highbay LED with PDC housing suitable for ceiling (Surface/Suspended) mounting with system efficacy upto 150 lm/W incl connecting with suitable size wire from ceiling rose to light fittings . Make :Havells cat Part No SAUCERGENXPROHBP80WLED757P90DBOLTG or Equivalent makes in Bajaj/Crompton. Warranty certficate for 2 years to be provided by Employee of Organization of Terittory.

S&F in replacement of SITC of high-quality integrated LED Street Light with a minimum system lumen of 4950 Lm and system wattage not exceeding 45W with a nominal efficiency 110 lumen/watt. CCT of 5700K with SDCM of < 5 and CRI >70. The housing should be of non-corrosive high-pressure die-cast aluminum with heat resistant toughened clear glass to with stand extreme environments with PF > 0.95. Lifetime of 50K hours @L70.The Ingress protection should be minimum IP 66 with an IK rating of 07. The Luminaire should have 4KV internal 10KV external surge protection in the Luminaire.Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters and including suitable size and length of flexible copper wire and making the connection including House service bracket for mounting light fittings House service bracket any type complete with 1.50mtr long galvanised iron pipe 40mm dia medium grade, bent to required shape including mild steel clamps of flat iron 40x6mm, hook, stay, nut, bolt and washer including painting with two coats of synthetic enamel paint over one coat of red oxide primer , complete all as specified, complete all as specified. Make : Bajaj cat part No ENXT P 54L WH PO PC SD or Equivalent makes in Wipro/Philips. Warranty certficate for 2 years to be provided by Employee of Organization of Terittory.

S&F in replacement of Ventilair fan, Plastic Body , sweep 250mm with louver shutter, superior rating for energy saving, copper wounded motor , Electrically operated automated front shutter Modern design, fashionable & elegant look and gravity Shutter To prevent entry of foreign objects like dust, bird, pets etc complete with nut bolts, washers incl making necessary connection with suitable size and length of wire of copper condutor, complete all as specified and as directed by Engineer-In-Charge. Make: Havells/ Crompton Greaves/ Usha/ Bajaj/ Orient. Note: Old Exhaust fan taken out from the existing opening and shall be deposited at Store Yard of MES and shall be the property of Deptt..

S&F in replacement of Ceiling fan, mettalic, sweep 1200mm, with BLDC Motor, high speed, inclduing necessary fitting/fixtures such as Hook and clamps etc including connectig wire of suitable size and length from ceiling rose to fan connector, having BEE Star Rating- 5 Star, Rated Power Input in Watt 28±10%, Rated Speed in RPM 345±10%, Rated Air Delivery in CuM/ Min- 220 Minimum, Service Value CMM/W 7.85 Minimum No of Speed 5 , Insulation Class- E, Temperature Rise @ Rated Voltage 25 degree Celcius (Max) by winding resistance measurement at an ambient 30 degree Celcius, High Voltage Test Withstands 1.5KV, Insulation resistance Above 2 MΏ, Type of Ball Bearings Single row deep groove ball bearings of 6202 sizes Top & Bottom Cover should be of aluminium, Type of Lubricant Used Lithium Based – Shell Alvania RL3, Material of Blade Aluminium, BEE Certification, Material of Canopies- Polypropylene, complete all as specified and as directed.. Make: BAJAJ Model No Energos 28 or Equivalent Makes in Havells / Crompton Greaves/ Usha / Orient Electric energy star Note: (i) Old Ceiling fan taken out from the existing opening and shall be deposited at Store Yard of MES and shall be the property of Deptt.” (ii) The Unit rate shall include the cost of MS brackets incl nut and bolts for hanging of the ceiling fans of any sweep.

S&F in replacement of Sheet metal enclosures for Triple Pole and Neutral distribution boxes with double door glazed for incorporating MCBs, IP-43, 4-way with 200 amps rated busbar, 240 volts, as per IS-8623, complete all as specified and as directed by Engineer-In-Charge.

S&F in replacement of Sheet metal enclosures for Single Pole and Neutral distribution boxes with double door glazed for incorporating MCBs, IP-43, 8-way with 200 amps rated busbar, 240 volts, as per IS-8623, complete all as specified and as directed by Engineer-In-Charge.

S&F in replacement of MCB, single pole, 6 to 32 Amps, 240 Volts, 50 Hz, including necessary incoming and outgoing electric connection with suitable size of copper lugs, complete all as specified and as directed by Engineer-In-Charge.

S&F in replacement of MCB, Single Pole and Neutral, 0-32 Amps (up to), 240 volts, 50 Hz, 'C' curve including necessary incoming and outgoing electric connection with suitable size of copper lugs, complete all as specified and as directed by Engineer-In-Charge.

S&F in replacement of MCB, Triple Pole and Neutral, 40-63 Amps (up to), 240 volts, 50 Hz, 'C' curve including necessary incoming and outgoing electric connection with suitable size of copper lugs, complete all as specified and as directed by Engineer-In-Charge.

Sheet metal enclosures in replacement of with socket plug top and MCB suitable for single pole and neutral including a two pin and earth plug and socket complete with one single pole MCB, single pole, 40 Amps, 240 Volts, complete all as specified and as directed.

S&F in replacement of Earthing complete with galvanised steel earth plate electrode 60 cm x 60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level. connecting to the GI wire 4 mm dia by means of bolls, nuts, check nuts and washers of galvanised iron and earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering , perforated at bottom. 1.75 metre long placed on top edge of earth plate. charcoal and common salt filling with fixing arrangement, funnel wire mesh and earth work in soft soil returning filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate 3 of SSR-2009 Part-I and connecting to earth test point all as specified or indicated including testing on completion. NOTE :- (i) Item of earthing includes cost of 7.5 m long GI wire of size 4 mm dia with protection pipe of 15mm dia GI medium grade, any variation in length shall be adjusted through deviation order based on SSR rates enhanced by (-40)%. (ii) On testing after completion of earthing if the desired earth resistance is not obtained earthing will be re-done by the contractor at his own risk and cost.

Making Provision of holes in brick wall for fixing of exhaust fan of size 250mm sweep incl making good to the disturbed surfaces to the existing specification, complete all as specified and as directed.

Excavation in trenches n exc 1.5 metre wide & n. exc 1.5 metre in depth for laying of cable and getting out in any type of soil, complete all as specified.

Returning filling in incl spreading watering and well ramming in layers in hard/dense soil each not exceeding 25cm thick complete all as specified.

Removing excavated materials/ soils, to a distance not exceeding 50mtrs and depositing where directed at a level not exceeding 1.50mtrs, complete all as specified and directed by Engineer-In-Charge.

Supply, laying commissioning, testing of the XLPE LT cable 1100 volts grade of size 16 Sqmm 2 core armoured, PVC sheathed with aluminium conductor heavy duty laid in trenches/fixing on wall in PVC conduit pipe with the help of clamp/shadels, under road crossing through protection pipe etc after taking out existing under ground cable, complete all as specified and directed.

Supply, laying commissioning, testing of the XLPE LT cable 1100 volts grade of size 25 Sqmm 3.5 core armoured, PVC sheathed with aluminium conductor heavy duty laid in trenches/fixing on wall in PVC conduit pipe with the help of clamp/shadels, under road crossing through protection pipe etc after taking out existing under ground cable, complete all as specified and directed.

Sand cushioning to protection of underground cables, laid 8 Cm before laying and 15 Cm after laying of cable, and punned to form an overall layer of 18 Cm thick, complete all as specified and directed by Engineer-In-Charge. Note: Punned thickness shall be measured.

Sub class ‘B’ bricks, modular size, brick covering laid dry, flat, transversally along the length of cable on sand cushioning for mechanical protection of cable, with width equal to the length of the brick, complete all as specified.

S&F Tubes, Light grade' galvanised, 40mm bore, ISI marked for the protection of cable in trecnhes or fixed to wall incl necessary clamps , nut and bolts , complete all as specified and as directed.

Disconneting , removal of existing spilit AC (indoor or outdoor) carefully of capacity 1.0 Ton to 2.0 ton and re-fixing of the same at new location incl making connetion and re-filling of refrigerent gas if required, complete all as specified and as directed.

Amount of Schedule of credit of for Rs 1,06,280.00 shall be deducted from quoted amount.

M/s Rajesh Kumar Contractor

M/s Joginder Lal Malhotra

CHOPRA CONSTRUCTIONS

M/s Shivam Construction Co

M/S SAHNI CONSTRUCTION CO