ADDN/ ALTN TO ALL MAIN GATES UNDER INS TANAJI AREA AND PROVN OF LIGHTNING ARRESTORS IN BLDG NO P-13 AT CABS UNDER GE (NW) MANKHURD

Amount

S&F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe-410W (Gde E-250, quality 'A') complete all as specified and directed.

M & L for 1.60mm thick mild steel, plain black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

Demolition of brick work or stone/ boulder mansonry built in cement mortar complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Excavation in trenches,n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc or shaft wells, cess pits, manhole, pier holes n.exc 10 Sqm on plan and n.exc 1.5 m in depth and getting out in Soft /loose soil complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded aggregate) as in foundations,filling and mass concrete complete all as specified and directed.

M&L RCC nominal mix, type B1, 1:2:4 (20 mm graded aggregate) as in foundation, including rafts, footings, foundation beam, plinth beams, bases for columns etc, basement slabs under reamed plies and mass concrete complete all as specified and directed.

M&L RCC nominal mix, type B1, 1:2:4 (20 mm graded aggregate) as in columns, pillar, pier etc complete all as specified and directed.

M&L RCC nominal mix type B1, 1:2:4 (20 mm graded aggregate) as in beams, lintels over 1.5m span complete all as specified and directed.

Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and beams sides and soffits (if any) of foundation and plinth beams; and similar work for rough finished surface of concrete etc complete all as specified and directed.

Use and waste forrnwork to sides of pillars. posts. struts. piers. columns and stanchions for rough finished surfaces of concrete, square, rectangular or polygonal etc complete all as specified and directed.

Use and waste of formwork to edge of concrete flat,treat, break in floors,window cills, concrete railling, opening in concrete wall ,floor and roof nexc 20 cm wide and side of RCC bands in walls, horizontal or sloping and similar work exc 10 cm and n exc 20cm wide for rough finished surfaces. and complete all as specified and directed

M&L for TMT steel bars 10mm dia and over, cut ot lenth,bent to shape required,including cranking bending spirally for hooping for columns,hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

All as per Item No 13 but 5mm dia and over upto including 10mm dia in stirrups, spacers and binders complete all as specified and directed

M&L PCC block masonry with solid blocks, grade C (5.0) exc 10 cm in width and setting in cement mortar (1:6) etc complete all as specified and directed.

Returning,filling in,including spreading, levelling,watering and well ramming in layers n.exc 25cm thick in soft/loose soil complete all as specified and directed.

Removing excavated material outside MD land complete all as specified and directed.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6, as in wall etc complete all as specified & directed. Note: PCC bond stone and face work shall be measured and paid separately.

Taking down cement plaster of any description on brick wall, ceiling etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Raking out joints/pointing to random rubble or polygonal rubble uncoursed or brought up to courses in cement mortar complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of bricks or concrete surface work in CM 1:6, finished fair and even without using extra cement including necessary scaffolding complete all as specified and directed.

M & L for broken glass coping on top of walls in CM 1:3 complete all as specified and directed.

S&F in repairs galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provn of galvanised mild steel wire, staple or steel pins etc complete all as specified and directed. Note : Each line wire to be measured

S & F in repairs barbed razor type concertina coil DG hot galvanised spring for site wire manufactured by M/s Special steel Ltd or M/s Super Fence or M/s Global Engrs as approved by GE, 1.45 to 1.50 Kg/metre and dia of coil when stretched 610 mm complete all as specified and directed.

M & L two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer including preparation of previously untreated surfaces of steel and iron exc 10 cm width or girth complete all as specified and directed.

M&L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over & including screed bed 15 mm thick in cement mortar 1:4set and jointed in neat cement slurry and pointed in white or coloured cement to match Colour is approved by GE complete all as specified and directed.

M&L for 12-15mm thick dholopur tiles of size 200x100mm fixed in vertical surfaces over & including screed bed of 10mm thick in cement mortar 1:4 set and jointed in cement slurry at pointed in white or coloured cement to match with existing, complete all as specified and directed.

M&L for stainless steel word at any location including screwing , fixing it to the wall with suitable adhesive material complete all as specified and directed. (size of letter shall be 250 x 35 x 25 mm with thickness 1.5mm)

M & L for sand cushioning by spreading in trenches fine dry river sand by gently by punning down manually as in cable protection complete all as specified and directed. Note : Punned thickness will be measured and paid.

Supply and laying un-reinforced precast concrete cable cover class LV, type-I, flat size 250mm x 150mm x 40mm laid in trenches complete all as specified and directed.

Supply, laying and testing cable XLPE insulated screened PVC bedded, ISI marked, galvanized steel strip or wire armoured, electric power cables (heavy duty with stranded aluminium conductor 1100 volts grade of 3 core 4 sqmm including saddling in wall, cable duct with lugs & spacers connecting to LT panels etc complete all as specified and directed.

M&L for cutting / boring of PCC/hard standing at a depth not more than 15 cm deep and 15 cm in breadth for passing earthing conductor and making good the disturbed surfaces with PCC (1:2:4) type B-0 or cement mortar (1:3) complete all as specified and directed.

S& F GI steel tubing light grade 40 mm dia for laying in ground for road crossing etc for cable protection including necessary fittings , clamps for supports, etc complete all as specified and directed.

S&F cable junction box IP 66 with metric knockouts for cable entry of size 130x180x77 mm, fixed on poles / walls with suitable fixing arrangements viz. 25x3mm GI clamps fixed with GI nuts and bolts, washers, etc complete all as specified and directed.

S & F MCB DB 2 way SPN, double door, IP - 53 with 200 Amps rated bus bar and connecting up complete all as specified and directed.

S & F MCB SP 32 Amps, 240 / 415 Volts, 50 Hz, 10 KA breaking capacity complete all as specified and directed.

Supply and fix LED 50 Watt flood light fittings complete with and including drivers, pressure die cast aluminium housing, prewired complete. The fitting shalll conform to cat No . JETACOMPECTOFL50WLED757LTG of Havellsi/Bajaj/Crompton Greaves/ Philips/ Wipro complete all as specified and directed.

S&F mild steel angle sections of 25x25x5 mm size including clamps, bolts, nuts, washers drilled for bolt, welding, bending cold or hot in any shape or size as directed and painted with two coats of aluminium paint over a coat of red oxide Zinc chrome primer for fixing gate lights in wall/ floors etc complete all as specified and directed.

M & L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers all as shown in Electrical Plate No.3 of MES SSR part-I 2009 connected to earthing test point all as specified or indicated including testing on completion including earthwork, PCC chamber, CI cover protection & watering pipe funnel mesh etc all as required at site complete all as specified and directed.

M&L for earthing complete with Copper earth plate electrode 600x 600x 3.15 mm thick buried directly in ground with top edge of the plate not less than 1.5 mtrs below normal ground level and connected to earth test point by means of copper Strip of size 20x3 mm as earthing lead all as specified and shown in electric plate No 3 of MES SSR Part-I 2009 including earthwork, PCC chamber, CI cover, protection and watering pipe, funnel, mesh etc all as required at site and all as directed. Note: (1). 7.5 RM Copper strip in deemed to be included in quoted rates beyond 7.5 RM strip shall be measured and paid separately (2). Rate quoted by the tenderer is deemed to include salt & Charcoal upto & above 450 mm top of Copper plate complete all as specified and directed.

Supply & fixing for copper strip 20 x 3.15mm on wall/roof/batten or recessed or buried in ground including all insulators, screw, nut bolts for roof conductor and down conductor complete all as specified and directed. Note : Insulator support shall be placed at a distance not more than 40 cm from each other. All screws, nuts/ bolts shall be chromium plated type

Supply & Fixing air termination Copper rod 12 mm dia, 300 mm long for lightening conductor including copper base plate with all necessary nut bolts and drilling job etc.complete all as specified and directed.

M&L for test point terminal block made of gun metal or phosphorus bronze size 75x75x25 mm drilled and screwed including 3 nos. 8 mm dia, 25mm long hex. head screw complete all as specified and directed.

M&L for painting on wall with synthetic enamel paint of black colour background of 200 x 150 mm size and writing work with white synthetic enamel paint for earth test result with date & year complete all as specified and directed.

M&L for lightening conductor assembly made out of GI pipe light grade of size 50 mm bore along with welded flange at one end & GI reducer socket 50 x 40mm at another end connected with GI pipe light grade of size 40 mm bore of suitable length with one end GI reducer socket to connect air termination & connector for earth strip duly fixed with necessary nuts bolts & washers in PCC 1:2:4 type B0 30cm x 30 cm x 30 cm complete all as specified and directed. A sum of Rs 3,550.00 towards sch of credit shall be deducted to arrive the contract sum.

M/s Hari Om Construction

A P ENTERPRISES

Joy builders

mp construction co