CLEANING OF EXISTING SEWAGE LINE, SEPTIC TANK AND REPAIR TO DRAIN, CULVERT, FENCING, JAFFERY WALL, PATH, HARD STANDING ETC IN NEW PINTO PARK AT AF STN BASANT NAGAR UNDER GE (AF) PALAM DELHI CANTT-10

Amount

Demolition of brick work built in cement mortar, including all quoins, arches, pillars etc of any description including removing debrish from site complete all as specified and as directed.

Demolition of concrete in ground floor and paveings n.exc 15 cm thickness below or above ground level complete all as specified and as directed.

Demolition of reinforced concrete roofs, floors (other than ground floors), beams, staircases, landing, chajjas slabs and similar suspended work complete all as specified and as directed.

Taking down cement plaster or cement lime plaster on brick or stone walls etc including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any dscription not otherwise provided for complete all as specified and as directed.

Cleaning of SGSW pipe lines 150 mm bore pipe and removing the blockage by means of rodding with and including bamboo splits/flexible iron wire or concrete malacces rods from manhole to manhole, through pipes from trap to manhole, rendering the system clear and flushing the delogged line with sufficient quantity of water and removing sludge/waste material etc. to a distance n. exc 50 M and burrying in pits and re-filling the same complete all as specified and as directed. Note:- The cost for excavation and earth work for pits is deemed to be included in the unit rate.

Description all as per Serial Item No 6.00 herein above but for pipe line of 200 mm bore pipecomplete all as specified and as directed.

M&L for cleaning of manholes n. exc 1.0 m deep and removing sludge/waste materials etc to a distance n. exc 50 m and burrying in pits and re-filling the same complete all as specified and directed. Note:- The cost for excavation and earth work for pits shall be deemed to be included in the unit rate.

Description sll as per ser item No 8.00 above but deep exceeding 1.0 M and n. exc 1.5m complete all as specified and as directed.

Description all as per ser item No 8.00 here in before but exceeding 1.5 M and n. exc 2.5m deep complete all as specified and as directed.

Cleaning of blocked floor/Nahani trap and CI pipe upto 1st manhole and removing all silt, residue sludge both organic and in organic nature including any type of foreign materials and removing waste materials/ sludge etc to a distance exceeding 50 mtr and sealing the sides of traps in bath room/ kitchen using Aqua TS of Aqua shield water proofing or equivalent, any damage caused during cleaning shall be made good by contractor to the entire satisfaction of Enginner-in-Charge.

Cleaning of blocked WC trap and CI pipe upto 1st manhole and removing all silt, residue sludge both organic and in organic nature including any type of foreign materials and removing waste materials/ sludge etc to a distance exceeding 50 mtr and damage caused during cleaning shall be made good by contractor to the entire satisfaction of Enginner-in-Charge.

Demolition and breaking up 150 mm internal dia drain pipes (slat glazed ware, AC or reinforced concrete) set in cement mortar complete all as specified and as directed.

Description all as per Ser Item No 13.00 herein above but 200 mm bore drain pipe complete all as specified and as directed.

M&L for reinforced concrete pipes, class NP2, 150 mm bore, laid and jointed complete with and including collars complete all as specified and as directed.

Description all as per ser item no. 15.00 above, but 200 mm bore pipe complete all as specified and as directed.

M&L for 100 mm thick concrete bed to drain pipes in cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregate) including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and as directed.

Description all as per Ser Item No 17.00 here- in-after above but for 200 mm bore pipe complete all as specified and as directed.

M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggregates) as in foundations, filling and mass concrete etc complete all as specified and directed.

M&L PCC (1:3:6) type C-2 (using 20 mm graded stone aggregate) as in surface channel, drain and manholes complete all as specified and as directed.

M&L PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in benching, coping including necessary use and waste of form work complete all as specified and as directed.

M&L for PCC (1:2:4), type B-2 (using 20 mm graded crushed stone aggregate) as in surface channel, drain and bedding including necessary use and waste of form work and weathering, slightly rounded or chamfered angles complete all as specified and as directed.

M&L for providing reinforcement cement concrete nominal mix (1:2:4) type B1 (using 20mm gradedd stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

M& L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for precast cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregates) as in landing cover slab, drain and manhloe cover, shelves troughs and the like including weathering, slightly rounded or chamfered angles and throating set in cement mortar (1:4) complete all as specified and as directed.

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre depth for foundation, manhole etc not exc 10 Sqm on plan and not exc 1.5 metre in depth including getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in soft/loose soil complete all as specified and as directed.

Removing excavated surplus soil/material not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed.

M&L for mild steel works (Fe-290 Grade E-165) as in posts and struts etc in fencing of angle or other sections, including cutting tops to shape as directed, drilling holes, notching for wire etc, comlete all as specified and as directed.

M&L for mild steel plain bar 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed.

M&L for chain link fencing 4 mm dia of galvanized steel wire (150 x 100)mm mesh made up into mattresses or cages, lapped wire & laid in position including closing after filling etc including binding with wire complete all as specified and as directed.

S&F rolled mild steel grade Fe-290 Gde-E-165 quality-A as in framed work as in doors or gates of angle or other section gates of with gusset plates, rails, cladding, chowkhats/frame or like etc welding hold fast, hinges complete all as specified and as directed.

S&F hard drawn steel wire fabric cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia weight per sqm not exc 4kg complete all as specified and as directed.

M&L for cutting holes in brick walls, built in cement mortar or cement lime mortar, exc half brick but not exc one brick thick, for inserting hold fasts and making good dismantled portion in cement mortar (1:3) or cement concrete (1:2:4) type B1 complete all as specified and as directed.

M & L for removing loose, disturbed or disintegrated old concrete surfaces of RCC beam, column, lintel, pardi, railing, slabs etc, cleaning thoroughly exposed reinforcement, by sand blasting using suitable pump as directed by the GE, preparing exposed concrete surfaces to receive guniting, applying one coat of anti corrosive paint to the exposed reinforcement, supply and fix welded wire mesh of size (100 x 100) mm of 3 mm dia wire, weight not less than 1.37 Kg/Sqm & binding with 22 guage mild steel (annealed) binding wire to reinforcement and applying pressure guniting in cement mortar (1:3), average 30mm to 50mm thickness and thereafter rendering 10mm thick plaster in cement mortar (1:4), mixed with water proofing compound @2% by weight of cement and finishing the surfaces even and smooth without using extra cement to match with the existing surfaces, removing the debris outside MD land including material and labour upto G+3 storey for necessary scaffolding and safety arrangement for guniting work, complete all as specified and as directed. Note:- The finish of the surfaces to be matched with the existing surface. WPC shall be measured & paid separately as supply only).

M&L for brick work with sub class `B' bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and as directed.

M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:4), surface finished even and fair including necessary scaffolding up to 18 m height complete all as specified and as directed.

M&L for 10mm thick plaster on fair faces of brick work or concrete surfaces in cement mortar (1:3) as in ceilings, surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:6) surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparing plastered or unplastered new surfaces on ceilings including brooming down or steel wire brushing, scraping down and applying three coats of white wash complete all as specified and as directed.

M&L for preparing plastered or unplastered old surfaces on ceilings including brooming down or steel wire brushing, scraping down and applying two coats of white wash complete all as specified and as directed.

M&L for preparing plastered or unplastered new surfaces on walls including brooming down or steel wire brushing, scraping down and applying two coats of distemper oil emulsion over a coat of alkali resistent primer complete all as specified and as directed.

M&L for preparation of surfaces plastered or unplastered new surfaces on walls including brooming down or steel wire brushing, scraping down and applying two coats of cement base paint of approved colour and shade complete all as specified and as directed.

M&L for preparation of plastered or unplastered old deorated surfces by complete removal of existing treatment and applying two coats of oil bound distemper over a coat of 1 mm thick cement base wall care putty complete all as specified and directed.

M&L for preparation of plastered or unplastered old decorated surface of walls by washing and rubbing down and brooming down or with steel wire brushing, scraping down, smoke soot's moulds, moss efflorescent salts& trading oil, greasy spots and filling cracks/holes by putty and applying one coat cement base paint walls complete all as specified and directed by Engr-in- charge.

M&L for preparation of new or previously untreated surfaces of steel of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over & incl one coat of red oxide primer complete all as specified and as directed.

M&L for preparation of old painted surfaces of wood & wood based surfaces of any description not otherwise described over 10 cm width & girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of old painted surfaces of steel and iron surfaces of any description not otherwise described over 10 cm width & girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Cleaning of PVC over head service tank of capacity exceeding 500 liters but not exceeding 1000 litres, cleaning by brooming, removing all dirt, vegetation grown on roof around tank if any, washing the tank with approved bleaching powder. Rendering it clean to store potable water after applying two coats of lime wash internally including writing the date of cleaning and capacity of tank with white synthetic enamel paint on the outlet surface directly visible (letters not exceeding 30 centi metre height) complete all as specified and as directed.

Description all as per Srl Item No. 50.00 here-in- above but of capacity exc 250 and not exc 500 liters complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premices complete all as specified and as directed.

Demolition of stone slabs and tiles laid, beded and pointed in any mortar of any description or thicknes in floors, aprons etc complete all as specified and as directed.

M&L for joint free non skid coloured ceramic tiles, 7 to 8mm thick (squre or rectangular) area of each tile n. exc. 0.11sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces, laid over & including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

M&L for joint free coloured glazed ceramic tiles in vertical surfaces of size (450x300)mm x7mm thick, set and jointed in cement slurry and pointed in white or coloured cement to match with and including laid over 15mm thick cement rendering in cement mortar (1:4) complete all as specified and as directed.

M&L for 20mm thick granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, walls window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with and including over 15mm thick screed bed or bedding layer of cement mortar (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match

M&L For Pre polished chequred cement concrete tiles 30x30 cm x 25 mm thick set jointrd and pointed neat cement slurry with gray cement and pigment in floors including 15 mm thick screed bed cm 1.4 ratio all as specified

M&L for 75 mm thick cement concrete type D2, 1:4:8 (using 40 mm graded aggregate) as in sub base, to be finished even and fair complete including use of necessary form work all as specified and directed.

M&L for hard core of gauge n exc 63mm, deposited spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size, with grey cement and pigment to match, conforming to IS 15658-2006 of 60mm thick M-35 grade laid over 50 mm thick sand cushioning complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in roof (tiling), staircase landing, floors (other than ground floor) including removal of debrish out of MoD Land complete all as specified and as directed.

Taking down existing tarfelt including plaster including removal of debrish out of MoD Land complete all as specified and as directed.

M&L for providing cement concrete (1:2:4), type B-0, (using 12.5mm graded stone aggregate) as in roof padding to maintain slope etc complete all as specified and as directed.

M&L for preparation surface including cleaning of all dirt and providing the following water proofing treatment in narrow width over the roof gutter of stores houses or chajjah/canopy/parapet wall, below PVC/RCC water tanks etc of G+3 storied building accessible / non accessible RCC roof to be executed through approved applicator of the membrane manufacturer with following specification etc complete all as specified and directed by Engineer-in-Charge.:- (a) Plastering 10mm thick in cement mortar (1:4) on concrete surfaces using WPC @3% by weight of cement, surface finished even and smooth. (b) Surface shall be throughly wire brushed, cleaned, washed, dried up properly and apply evenly a bituminuous primer coat conforming to IS @0.4 ltr /Sqm over concrete / plastered roof surface. (c) Applying evenly a tack coat of bitumen 85/25 grade @1.20 kg/ sqm. (d) Laying of 3mm thick APP membrane sheet (min weight 3 Kg/Sqm) consisting of a core of 160 gms/Sqm polyster non woven fabric mat protected on both sides with a high quality polymeric asphaltic mix again protected with thermo fusible HMHDPE FILM on dried primed surface by torch application method. APP membrane will normally be laid in length at right angle to the direction of slope. The overlap shall be minimum 100mm on longitudinal direction and 150mm on the transverse direction including cuttings, grooves etc. (e) Membrane bonded completely to the substrate & the over laps are then scaled/fused by flameand including two coat of water proofing bituminous aluminum paint on top of APP membrane all as directed.

M&L for cement concrete tiles of size (20cm x 20cm) x 20mm thick machine pressed, set & pointed in neat cement slurry in floor with grey cement and no pigment and cut and polished on roof over and including 15 mm thick screed bed in CM (1:4) complete all as specified and as directed.

S&F framed work such as grills, gratings etc with ends of bars shouldered and or reveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

M&L for steel plain, black sheet 1.00mm thick in wall cladding, steel gates and similar work, cut to size, holes round headed screws, clout nails or rivets and fixed to steel framing with plain 40mm lap joint with reveted or welded seams, including bending or turning up, mitred angles etc. complete all as specified and as directed.

M&L in repair cement concrete kerb stone in (1:2:4), type B-1 (using 20mm graded stone aggregate) and set in cement mortar (1:6) on road and path complete all as specified and as directed.

M&L in repair precast cement concrete louvres and jallies 40 mm thick in (1:2:4) type B-0 (using 12.5mm graded stone aggregate) including all mouldings but excluding frame and set in cement mortar (1:6) complete all as specified and as directed.

S&F stairs (framed) including stringers, treades, landing, balusters, hand rail, nosing in steps etc. including cleats, brackets, etc. complete all as specified and as directed.

Dismantling timber scantling 40sqcm over in section in any position complete all as specified and as directed.

Dismantling asbestos cement (corrugated, semi corrugated etc.) sheets in roof coverings complete all as specified and as directed.

S&F MS steel work in tubular trusses and tubular posts including special shaped washers etc., complete using but welded tubes confirming to IS 1161- 1979 graded St 240 complete all as specified and as directed..

S&F mild steel work (FE 290Grade E-165) roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and as directed.

S&F pre painted galvalume aluminium zinc coating GI based (Tiles Pattern) corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to fix the wall fixed with self taping scrows complete all as specified and as directed.

Demolition of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed.

M&L for providing & fixing false ceiling at all heights with semi perforated 12mm thick micro tegular edged GRG (Glass Fibre Reinforced Gypsum false ceiling tiles of size 595x595 mm of approved texture, design and patterns having moisture content less than 2% , humidity resistance of 99%, NRCO.50 TO 0.75 AS PER is 8225:1987, nONCOMBUSTIBLE AS PER bs 476 (PART 4) -1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000mm, cross-T of size 15x32 mm of length 1200 mm and secondary intermediate cross -T of size 15x32 mm of length 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e. 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85x25x2 mm, Galvanised iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall/partition with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wall wood screws complete all as specified and directed.

Dismantling water tanks exc 500 & n exc 1000 ltr capacity and removing to store complete all as specified and as directed.

S&F for 500 ltr rotational moulded polyethylene water storage tanks three layered (cylindrical vertical with closed top), hoisted and fixed in position complete all as specified and as directed.

M&L for 40 mm thick cement concrete (1:2:4) type B0 (using 12.5 mm graded stone aggregate) as in flooring, surface finished even and fair complete with and including necessary use and waste of form work complete all as specified and as directed.

Taking down AC or PVC pipes of 100/110mm dia of any description including all fittings complete all as specified and as directed.

Supply and fixing 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with and including suitable PVC clamps at one meter of interval complete all as specified and as directed.

S&F PVC (SWR) bends of radius, suitable for 110mm dia PVC pipes complete all as specified and as directed.

Removing loose sand and deposit site including loading, unloading and stacking and transport etc. and returning, filling same sand and sieves after spreading in layers not exceeding 30cm thick, watering, ramming and finishing to required size, shape, slope etc. complete all as specified and as directed by Engr-in -charge. Note:- Distance of depositing sand at site n. exc 100 m and where directed at a level n. exc 1.5 m above the starting point.

M&L for filling sand and saw dust mixture in a ratio of (1:1) by volume with proper sieving the sand of averaging size 1.18mm,100% passing through 2.36mm and 100% retained on 600 micron, spreading in layers not exceeding 30cm thick, watering, ramming and finishing to required size, shape, slope etc. complete all as specified and directed by Engr-in -charge. Note:- (i) prior approval of sand shall be taken by Engr-in-charge. (ii) Punned thickness of sand saw dust mixture shall be measured and paid.

M&L for machine cut kota stone slab flooring/steps and risers 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete with and including laid over 15mm thick screed bed in CM (1:4) complete all as specified and as directed.

Taking down precast cement concrete louvers and jallies including removal of debrish out of MoD Land complete all as specified and as directed.

M&L for 75mm thick PCC (1:2:4) type B2 (using 40mm graded stone aggregate) as in floor including necessary use and waste of form work complete all as specified and as directed.

JAIPAL AND BROTHERS (BID ID -3064003)

Arihant Enterprises (BID ID -3063474)

Commercial Traders (BID ID -3072369)

RK TRADERS (BID ID -3063363)

DEV CONSTRUCTION (BID ID -3063227)

M/S Satyam Associates (BID ID -3063877)