From Taluka Border to Nandane and Sayane to Deobhane and upto Dhamani to Biladi and Arni to Ambode upto Mukti road (Construction of Concrete road to Nandane(District Border) Sayane Devbhane NH-3 Dhamane Biladi Nimkhedi Aarni Vani Malane Ambode Nandan

Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50 metre and spreading for embankment or stacking as directed.

Providing earth work in embankment with approved materials obtained from departmental land upto lead of 50 metre including all lifts, laying in layers of 20 centimetre to 30 centimetre thickness breaking clods, dressing to the required lines, curves, grades and section, watering and compaction with vibratory roller to achieve not less than 97 % of standard proctor density Etcetera complete (Material obtained from departmental Land)

Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at Optimum Moisture Content, carriage of mixed Material to work site, spreading in uniform layers with motor grader/ Paver on prepared surface and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- Plant Mix Method and Grading - I Material

Construction of dry lean cement concrete Sub-base over a prepared sub-grade with coarse and fine aggregate (natural sand/ Verticle Shaft Impactor grade finely washed crushed sand) conforming to Indian Standards: 383, the size of coarse aggregate not exceeding 25 milimetre, cement content not to be less than 150 kilogramme per cubic metre, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor /by suitable means as approved by Engineer-in-charge , compacting with vibratory roller, finishing, curing and including preparation of sub-grade surface if required etcetra complete. with fully automatic micro processor based Programmable logic controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetra complete.

Providing and laying 125 micron Low Density Polyethylene (LDPE) sheet confirming to Indian Standards 3395 : 1997 below concrete pavement including all materials and labour complete.

Providing and laying in-situ Mix-40 Grade unreinforced plain cement concrete pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate (natural sand/ Verticle Shaft Impactor grade finely washed crushed sand) conforming to Indian Standards 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013, mixed in a batching and mixing plant/ non tilting mixer and Weigh batcher as per approved mix design, admixtures, transporting to site, spreading, laying with approved make paver,compacted and finished in a continuous operation, finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound /by providing cement vata in cement Mortar 1:8 @ 0.6 metre X 0.6 metre centre to centre, admeasuring 80 milimetre at bottom and 40 milimetre at top with depth of 75 milimetre and maintaining the same throughout curing period by any other method approved by Engineer-in-charge. with fully automatic micro processor based Programmable logic controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetra complete.

Providing and fixing in position Thermo Mechanical Treated FE 500, 25 milimetre dia dowel bars precoated with anticorrosive epoxy paint of required diametre 60 centimetres Long and at 30.00 centimetre Centre to Centre and wherever directed including handling, straightening, necessary cutting supported by Thermo Mechanical Treated FE 500, chairs with proper alignment by using properly designed assembly of Bulkheads lubricating half length with bituminous paint as directed Etcetera complete.

Providing and fixing in position Thermo Mechanical Treated FE 500, tie bars precoated with anticorrosive epoxy paint of 12 milimetre diametre 70 centimetres long and at 30.00 centimetre Center to Center and wherever directed including handling, straightening wrapping with paper of approved quality for half length, necessary cutting, handling, straightening, supported by assembly of Thermo Mechanical Treated FE 500, chairs with proper alignment Etcetera complete.

Cutting transverse contraction joints 3 to 4 milimetre wide and depth 60 milimetre in concrete slab using concrete cutting machine with diamond studded saw within 48 hours of casting of bay / slab Etcetera complete including subsequent widening of the groove 8 to 10 milimetre wide at top having depth of 15 milimetre as directed by Engineer incharge.

Providing to contraction joints polysuphide sealent (Pouring grade) confirming to BS : 5212 - 1989 into sawed groove widened at top for sealent reservoir of specified size and shape as per detailed drawing including fixing Polyethylene foam backer rod of required diameter (appraox. 25% larger than the initial 3 milimetre to 4 milimetre joint) overlaid with bond breaking tape as per detailed drawing. Item includes cleaning the joints with water jet / air compressor and allowing joint to become thoroughly dry before sealent Indian Standards applied and applying primer. (A) Contraction and longitudinal joints (15 milimetre deep x 8 milimetre wide)