REPAIR TO JOINERY FLOORING TILING AND ELECTRICAL WORK AT ENTITY B 61 WEU HIRANKUDNA UNDER AGE BR II AND REPAIRS TO TOILET BATHROOM SUNKON SHAFT LEAKAGE SEAPAGE PLUMBING ETC OF OFFRS MD ACCN AND OTM ACCN IN THE AOR OF AGE BR I NORTH UNDER GE NORTH

Amount

Dismantling timber scantling in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section unframed work complete all as specified and directed

Taking down chowkhat with shutters with out taking off shutters from the frame n.exc 1.5 Sqm each complete all as specified and directed

Taking down chowkhat with shutters with out taking of shutters from the frame exc1.5 Sqm but n.exc 4 Sqm each complete all as specified and directed

Taking down door shutters of any description exceeding 1 square metre and not exceeding 2 square metre each easing, and adjusting as required and re-fixing in same opening including renewal of screws complete , all as specified and directed by Engineer-in Charge.

Taking down shutters of any description exc 1.00 sqm but n.exc 2 sqm each complete all as specified and directed.

Refixing in same opening of any description exc 1 sq. m and n exc 2 sq. m each complete all as specified and directed.

S&F Glazed and skeleton shutters, open rebated and 35mm thick 2nd class hardwood prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. cla-use 8.20 (a); supplied and fitted to chowkats etc complete all as specified and directed.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed

S&F Steel ventilators with centre hung shutter including hinges,steel peg stay, complete all as specified and directed

S&F Galvanised stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed

S&F, in repairs, Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks/screws/ galvanised wire staples in all type window like tubelar sectin,Z section , aluminium window, complete all as specified and directed.

S&F butt hinges med weight cold rolled SS, size 100 mm complete all as specified and directed.

S&F 150mm long Mild steel barrel tower bolts, stove enamellled black, with bright bolt and fixed complete all as specified and directed.

S&F 150mm long Mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed.

S & F 300 mm long Mild steel sliding door bolts plate type, store enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F, in repair, ordinary rat tail rod pattern spring incl roller and roller plate complete 300mm of mild steel incl necessary welding for fixing arrangement etc complete all as specified and directed.

S & F aluminium powder coated three track window ( two shutters glazed & one shutters wire gauge) with frame, glazed with 4 mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber beading joining cleat for fixing in position, concealed type lock for all three shutter, PVC roller etc all as specified below :-- (a) Frame (top & side) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 21447) (b) Frame (bottom) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 21446) (c) Top & side Members of shutter Section shall be be of size 18.00 x 40.00 x 1.50 (Section No 21455) (d) Interlock Section of Shutter shall be be of size 18.00 x 40.00 x 1.50 (Section No 21454) (e) Bottom Members of shutter Section shall be be of size 18.00 x 40.00 x 1.50 (Section No 20844) Note:-(i) Section Number given above are of make Jindal, Contractor may use similar section of other make mention in Appx 'B

S&F aluminium door shutter with frame100X45X1.5mm powder coated fixed to wall with steel fastnes min four number each side partly glazed with 5 mm thick tinted glass and partly panelled with 8mm thick coloured aluminium composit panels incl rubber beading, joining cleat for fixing in position, 2 numbers aluminium door handle 250 mm long, 1 number aluminium barrel tower bolt 200 mm long ,1 number aluminium floor door spring & one No 4 liver mortice lock of Godrej of size 100 mm in each shutter will be provided all as specified and directed as per following specifications -- (a) Vertical Members of shutter (Style) Section shall be of size 85.00 x 44.45 x 1.50 mm (Section No 19560) (b) Top rail ( Top Members) of shutter Section shall be of size 85.00 x 44.45 x 1.50 mm (Section No 19581) (c) Lock rail (Middle member) of shutter Section shall be of size 150.00 x 44.45 x 1.50 mm (Section No 19596) (d) Bottom rail ( Bottom Members) of shutter Section shall be of size 150.00 x 44.45 x 1.50 mm (Section No 19584) (e) Glazing clip for securing glass of shutters shall be of 0.80 mm thick (Section No 19370). Standered quality rubber beading shall be used for securing of glass (f) Top, Bottom and verticle member of shuttert will be tightened with hexagonal nut and purpusly made bolt of 10mm dia MS round bar threaded on both the end . Note:-(i) Section Number given above are of make Jindal, Contractor may use similar section of other make mention in Appx B.

S&F aluminium anodised powder coated Deco grill DG-104 10mm wide with U shape snap beading all as Complete specified and directed.

S & F Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, as specified.

S&F Factory made solid panel PVC door shutter 30 mm thick ( style ) consisting of frame made out of mild steel tubes for top and bottom rails . Mild steel frame shall be covered with heat moulded plain cover PVC 'C' channel having a PVC sheet strip of 20 mmcomplete all as specified and directed . Make Rajshri

S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming toto Fe.290.Gde-E-165 complete all as specified and directed.

M&L Welding in repairs n. exc 6mm thick metal and n. exc 2.5 cm in length all as specified and directed..

Cutting holes in brick walls built in cement mortar for inserting hold fasts and making good dismentled portion in CM 1:3 or cement concrete 1:2:4 type B-I as required, Exc half brick but not exc one brick wall.

M & L for appying two coats of synthetic enamel paint over a coat of red oxide primer on new steel surface including preparation of surfaces complete all as specified and directed.

M&L two coats of synthetic enamel paint over one coat of primer on new wooden surfaces including preparation of surfaces exc. 10 cm width or girth all as specified.

S&F, 3 mm thk sheet glass ordinary quality and galzing with oil putty or wodden beads in square n.exc 0.5 sqm each complete all as specified and directed.

S&F, 3 mm thk sheet frosted glass ordinary quality and galzing with oil putty or wodden beads in square n.exc 0.5 sqm each complete all as specified and directed.

S&F, 3 mm thk sheet frosted glass ordinary quality and galzing with oil putty/wooden / aluminium beads in square n.exc 0.5 sqm each including hacking out old broken glass ( any thickness ,size,quality or description) from wooden frame work, glazed with oil putty or fixed with wooden beads complete all as specified and directed.

S&F, 3 mm thk sheet glass ordinary quality and galzing with oil putty/wooden/steal beads in square n.exc 0.5 sqm each including hacking out old broken glass ( any thickness ,size,quality or description) from wooden frame work, glazed with oil putty or fixed with wooden beads complete all as specified and directed.

M&L Taking down cement plaster from other than fair faces of any description from brick, stone walls or concrete surfaces including raking out joints, hacking for key,scrubbing down with water , rendering 15mm thick in cement mortar 1:6,mixed with PD proof 101 LW(+) of Dr fixit or equvalant integral WP admixer @200 ml/bag of cement over two coats of super latex 302 of Dr fixit or equ. in the ratio 1:4: 7 (one part super latex 302, 4 part water and 7 part cement ) @ 1.50 Kg of homogenious mixture per Sqm in two coats and finished the surface even and fair without using extra cement complete all as specified and directed. Note- PD proof 101 LW(+) and super latex 302 shell be measured and paid seperatly

M&L Taking down cement plaster of any description from brick, stone walls or concrete surfaces including raking out joints, hacking for key,scrubbing down with water,and rendering 15 mm th in cm (1:4) in two layers (10mm+5mm ) mixed with PD proof 101 LW(+) of Dr fixit or equvalant integral WP admixer @200 ml/bag of cement over two coats of super latex 302 of Dr fixit or equ. in the ratio 1:4: 7 (one part super latex 302, 4 part water and 7 part cement ) @ 1.50 Kg of homogenious mixture per Sqm in two coats and finished the surface even and fair without using extra cement complete all as specified and directed. Note- PD proof 101 LW(+) and super latex 302 shell be measured and paid seperatly

M&L cement plaster of any description from brick, stone walls or concrete surfaces including raking out joints, hacking for key,scrubbing down with water,and rendering 15 mm th in cm (1:4) in two layers (10mm+5mm ) mixed with PD proof 101 LW(+) of Dr fixit or equvalant integral WP admixer @200 ml/bag of cement over two coats of super latex 302 of Dr fixit or equ. in the ratio 1:4: 7 (one part super latex 302, 4 part water and 7 part cement ) @ 1.50 Kg of homogenious mixture per Sqm in two coats and finished the surface even and fair without using extra cement complete all as specified and directed. Note- PD proof 101 LW(+) and super latex 302 shell be measured and paid seperatly

M&L Taking down cement plaster of any description from brick, or concrete cieling surfaces including raking out joints, hacking for key,scrubbing down with water,and rendering 10 mm th in cm (1:4) in mixed with PD proof 101 LW(+) of Dr fixit or equvalant integral WP admixer @200 ml/bag of cement over two coats of super latex 302 of Dr fixit or equ. in the ratio 1:4: 7 (one part super latex 302, 4 part water and 7 part cement ) @ 1.50 Kg of homogenious mixture per Sqm in two coats and finished the surface even and fair without using extra cement complete all as specified and directed. Note- PD proof 101 LW(+) and super latex 302 shell be measured and paid seperatly

Supply only PD proof 101 LW (+) of Dr Fixit or eqe. complete all as specified.

Supply only super latex 302 of Dr Fixit or eqe.complete all as specified.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of birla white putty over a coat of primer complete all as specified and directed.

M&L preparing newly plastered surfaces and applying two coats of cement base paint over a coat of primer on wall complete all as specified and as directed .

M&L for preparation of newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing the serviceable tiles to store and rubbish off the premises etc complete all as specified and directed..

M&L for glazed ceramic coloured tiles of size 350 X 250 X 7mm / 450 X 350 X 7mm thick on vertical surface such as dado, skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including layer 10mm thick in cement mortar 1:4 complete all as directed and specified

'M&L non skid coloured ceramic tiles 7 to 8 mm thick (square/rectengular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor, over 15mm thick screed bedding layer of mortar in CM 1:6 for laying floor finish complete all as specified and directed.

'M&L non skid coloured ceramic tiles 7 to 8 mm thick (square/rectengular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor, over 15mm thick screed bedding layer of mortar in CM 1:6 for laying floor finish complete all as specified and directed.

M&L for Vetrified Ceramic tiles 10 mm thick (Square/rectangular) lightshade,polished area of each tile not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor, over 15mm thick screed bedding layer of mortar in CM 1:6 for laying floor finish complete all as specified and directed. .

'M&L non skid coloured ceramic tiles 7 to 8 mm thick (square/rectengular) area in vertical surface as skirting/dado of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor, and including layer 10mm thick in cement mortar 1:4 complete all as directed and specified

M&L for Vetrified Ceramic darkshade tiles 10 mm thick (Square/rectangular) polished area in vertical surface as skirting/dado of each tile not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor, and including layer 10mm thick in cement mortar 1:4 complete all as directed and specified .

Dismantling loose concrete cover of RCC coloums, beams, slabs, Chajjas (Soffit only), and the like as directed, roughening and cleaning concrete surfaces with steel wire brushes, washed with water and allowed to dry, including dusting of steel reinforcement applying two coats of Epoxy phenolic anti corrosive protective coat manufactured by Sika, product code Ferroguard 903 or equivelent in other makes as per list of makes, all as directed by Engr-in-charge, providing fabric mild steel wire mesh 75 mm x 75 mm of 2 mm dia as reinforcement to concrete surfaces, applying adhesive/admixture make Polycrete (Polycrete shall be procured from Chemisol Adhesive Pvt Ltd Co. or their authorized dealer.) or equvalent in other makes as per list of makes, over steel mesh and providing 25 mm thick (average thickness) guniting mix (using 1 part of ordinary portland cement 53 grade and 2 parts of ghaggar sand mixed with adhesive/admixture polycrete or equivalent as per manufacturers instruction or 3% by wt of cement all as directed with a pressure of 2 to 2.5 kgs per sqm by guniting machine and surfaces finished even and fair, including 15mm thick plaster in cement mortar 1:4 including liquid water proof compound, necessary steel scaffolding and shuttering for working platform/formwork etc complete all as directedby Engr -In -Caharge. Notes :- (i) Guniting work may be carried out upto 10 mtr height from ground level. (ii) Rates are inclusive of all adhesive,adimixtures and WPC liquid etc.

Demolition of cement concrete of any description and in any position(unreinforced) in ground floors below or above ground level n.exc 15 cm thick and clearing rubbish from site all as directed and specified.

M&L for 40 mm thick Cement concrete 1:2:4 type B-1 as in floor including surfaces to be finished even and smooth with using extra cement complete all as specified and directed

M&L for Glass dividing strips, 3mm thick and 38 mm wide complete all as specified and directed

M & L 75 mm thick Cement concrete 1:3:6 (40mm graded aggregate) in flooring or plinth protection including surfaces to be finished even and smooth without using extra cement complete all as specified and directed.

M&L Chequered cement concrete coloured tiles 20cm x 20cm x 25mm thick , set jointed and pointed in neat cement slurry in floors with white cement and pigments over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L for 60mm thick, machinne pressed precast concrtete interlocking pavers block with grey cement and no pigment any shape and size confirming to IS 15658-2006 of size 250x250mm, having compressive strength of M-35 grade zig,zag (uni-paver) over & including 50mm thick sand filling under floors in foundation etc complete as specified and directed.

Demolition of brick/stone masonry built in CM. all as specified.

M&L brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 all as specified.

M&L brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 but except bricks all as specified.

M&L half brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:4 all as specified and directed.

Dismantaling plain or corrugated AC sheeting corrugated or semi-corrugated etc. in roof covering all as specified and directed..

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550MPa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling of timber scantlings, of framed work, from any position & height 40 Sq.cm and over in section complete all as specified and directed..

S & F Steel work in tubular trusses/purlin of any size or shape including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 including nut,bolt, MS plate complete all as specified and directed by Engr-in-Charge.

S&F framed work as in doors or gates of angle or other section with gusset plates,rails,braces, etc.,complete drilled for fixing of steel sheeting in or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing complete, confirming; Fe 410-W. all as specified and directed

S&F in repairs 500 ltrs capacity two layer rotational molded polyethylene water storage tanks, colour white (cylindrical vertical with closed top) hoisted of and fixed in position incuding provn of inlet , out let and over flow connection with tank connection nipple of existing pipe dia including, dismantling existing water tanks etc all as specified and directed.

-- Ditto --as item above But 1000 ltrs capacity of tanks

S&F Ball valves 20 mm high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for ironpipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms)

S&F in repairs 15mm Gun-metal, globe or gate valves, with iron wheel head, screwd both ends or iron pipe and fixed etc all as specified and directed.

S&F in repairs 20mm Gun-metal, globe or gate valves, with iron wheel head, screwd both ends or iron pipe and fixed etc all as specified and directed.

M&L for Formwork for filleting to produce rebates to door frames etc. including any stops, mitres etc.to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizintal or sloping and similar work exc 5 cm but n exc 10cm wide complete all as specified and directed.

M&L Roughening surfaces of old concrete surfaces by picking sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @ 3 Kg/Sqm complete all as specified and directed

M & L for Water proofing treatment to RCC roof slab, walls, chhajjas etc, shall be carried out as specified below and as directed by Engineer-in-Charge. (a) M&L for 15mm thick plaster screed bed layer in CM 1:3 on existing surfaces. (b) Preparing plastered surfaces of roof slab, walls, chhajjas etc, by brooming with broom sweeping free from dirt dust etc & evenly applying a coat of approved bituminous primer @ 0.40 Kg/Sqm of area complete all as specified. (c) Laying 3mm thick APP polymer modified approved membrane, non woven, polyester, weighing not less than 3.5 Kg/Sqm with laps & overlaps as specified & joints sealed and applied over a coat of bitumin of Gde 85/25 1.2 kg per sqm complete by torch application method all as specified & directed by Engr-in-Charge. Carrying out test by flooding water for 24 hrs for leakage & seepages and rectifying the same to the entire satisfaction of GE. (d) Finally applying a coat of solar reflective bituminous aluminium paint @ 0.15 ltr/Sqm on the top of membrane surfaces complete all as specified & as directed by Engr in Charge

M&L for plain cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in roof padding,roof kerbs of mud spots rounded or chamfered levelling /sloping course finished even and fair or to produce rebates to door frames etc complete complete all as specified.

M&L for Cutting chases, pinning in Brick walls making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and ctting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specified and directed.

Ditto as item 78 above for Cutting chases, pinning in Stone, concrete block or slab walls etc complete all as specified and directed.

Demolition of reinforced cement concrete in roof floor (other than ground floors) beams staircase, landing chajja and similar work complete all as specified.

M&L for Reinforced cement concrete 1:2:4 type B-1 ( using 20 mm graded cdrushed stone aggregate) as in chajjas and the like, all as specified and directed by Engr-in-Charge.

Use and waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick surface horizontal or sloping, fair finished surface of concrete, all as specified .

M&L for TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified.

M&L for TMT bars 6mm to 8mm dia in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified.

M&L for Rendering 10+5 mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified. (Water proofing compound to be measured and paid for separately).

M&L for Rendering 10mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement all as specified.

M&L for Rendering 10mm thick on other than fair faces of brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement all as specified.

M&L for Rendering 10mm thick on brick or concrete surface as in ceiling in cement mortar 1:3 finished even and smooth without using extra cement all as specified.

Supply only liquid water proofing compound complete all as specified.

M&LProviding cement concrete in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneeless apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 mix type B-0 etc complete all as specified & directed.

M&L for preparation of old decorated plastered or unplastered surfaces wall by brooming down scrapping down smoke and efflorescent salts etc and applying two coat of white wash on walls complete all as specified and directed.

Disconnecting existing overhead tanks,setting aside or lowered if required for repairing ,cleaning etc and hoisting if reqd reconnecting and refixing in position but capacity exceeding 250 litres and not exc 500 litres complete all as specified & directed.

Disconnecting existing overhead tanks,setting aside or lowered if required for repairing ,cleaning etc and hoisting if reqd reconnecting and refixing in position but capacity exceeding 500 litres and not exc 1000 litres complete all as specified & directed.

Cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc capacity exceeding 250 litres and not exc 500 litres complete all as specified & directed.

Cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc capacity exceeding 500 litres and not exc 1000 litres complete all as specified & directed.

S&F in repair ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (min wt 142 gm each) for 20 mm bore of pipe.

Taking up or down steel water tubing and connections 20mm bore pipe complete all as specified and directed.

M&L 20mm bore GI tubing medium grade with all fittings and fixed complete to walls, ceiling or laid in floor complete all as specified and directed.

Refixing of old steel tubing and connections in new or old position ( wall/floor/ceilings etc ) of size 20 mm bore complete all as specified.

Taking up or down steel water tubing and connections 15mm bore pipe complete all as specified and directed.

M&L 15mm bore GI tubing medium grade with all fittings and fixed complete to walls, ceiling or laid in floor complete all as specified and directed.

Refixing of old steel tubing and connections in new or old position ( wall/floor/ceilings etc ) of size 15 mm bore complete all as specified.

Taking down of eaves gutters and rainwater pipes (any size or any pattern),including all fittings etc. all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length rubber ring joints fixed to walls complete all as specified and directed.

Supply only 110mm bore PVC (SWR) bends with rubber ring joints fixed to walls complete all as specified and directed.

S&F in repair stop valve, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 20 mm bore complete all as specified.

S&F in repair water closet squatting pan ``Orissa pattern`` 580 mmx440 mm, white with integral foot rests including fixing charges of flushing cistern, connection to trap, anti syphonage pipe and provn of lime concrete etc complete all as specified.

S&F in repair Viterous China wash hand basin white, flat back size 550 x 400 mm incl CI or Angle iron 50x50x6 mm brackets one No CP fancy Pillar tap 15mm bore , one No 32 mm dia CP waste coupling, one No 32mm dia PVC flexible waste pipe and one No 15mm bore 450mm long PVC connection complete all as specified and directed by Engineer in charge.

S&F in repair PVC low level flushing cistern 10 ltrs capacity incl PVC float valves, PVC connection and out let pipes complete.

S&F in repair Bib cock with long thread, chromium plated , with long body, wall flange screwed for iron pipe or for brass ferrule and fixed to 15mm bore pipe complete all as specified.

S&F in reapir angular stop valve cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm dia pipe, all as specified. ISI marked.

S&F in rep Bib tap cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe of size 15mm bore chromium plated. all as specified

S&F in repairs Chromium plate tubular towel rail, 20mm dia, D type, 60cm long between flanges . all as specified.

S&F PVC connections 15 mm size with PTMT nuts of length 450 mm.

S&F in repairs plate rack made of stainless stee, 600 x 750X0.55mm including fixing as per manufacturers instruction. all as specified.

S&Fin repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar including fixing cantilever brackets connecting union to pipe and 32mm dia GI pipe duly painted upto Nihani Trap or Floor trap complete as directed at site, overall size 915mmx460mm bowl size 410mm x 330mm x160mm. all as specified.

M&L Indian type WC/EWC including demolittion of cement concrete (unreinforced) in sunken portion of WC, area n.exc 1.50 sqm including removing of unserviceable materials incl rendering 10 mm thick plaster in cement mortar ( 1:4 ) with WPC and laying lean concrete in bottom portion of WC and then applying 3mm thick APP membrane over bitumen primer surface of walls and bottom portion of WC with torch method , provide 32 mm dia GI tubing as spout of sunken portion 0.60 m long of approved quality , By filling Khanger / cinder and lean concrete, supply and fix vitreous china Squatting pan "Orissa pattern" size 580x440mm white, with integral foot rest & ' P' traps & jointing new 100 mm dia CI pipe with lead joints to WC ( excluding flushing cistern & flush pipe ) . Testing of sunken portion will be carried out by filling water for 24 Hrs in sunken area complete in all respect as specified and directed .

S&F in repair for Gypsum ceiling board for ceiling prepainted, perforated finish, 600 x 600 x 9 to 9.5mm thick in size, of approved brand/make, laid over and including grid work of size 600 x 600mm, made out of 0.5mm thick G.I. tee 32 x 24 mm for main, 25x24mm for cross tee and 20 x 20mm angle fixed on wall, powder coated finish on exposed faces of tee and angle. hung from ceiling using 2 mm thick G.I. Suspension wires spaced at 1200 mm on main runners including making niches for fans/light at as specified and directed.

S&Fin repair CP mixer, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, mixing 'Hot' or 'Cold' water with long screwed shanks and fly nuts, screwed for iron pipe and fixed of bore dia 15mm.

S&F in repair elegent mirror PVC cabinet with towel rail of size 450x600x150 mm all as specified

S & F Glass Shelf Corner trangular type shelf 250 mm radius with guard bars with CP brackets fancy type 5mm thick glass

S&F in repair Vitreous china wash down water closet pan (pedestal pattern), white including fixing bolts, flushing cistern and flush pipe connection to trap and to flushing pipe including provn of cement concrete beading complete all as specified and directed.

Supply only EWC Seat cover black colour of PVC complete all as specified and directed.

S&F in repairs shower rose fancy type bass chromium plated 125 mm heavy duty pattern with swivel joints type screwed for 15mm bore including jointing to pipe or unions complete all as specifed and directed.

S&F in repair CP hand spray (health facucet with 1.0 M long easy flex tube in chrome finish and wall hook) complete all as specified and directed.

S&F in repair 2 in 1 Angle Valve 15 mm CP fancy pattern type cast copper alloy screwed for iron pipe or forbrass ferrule and fixed all as specified and as directed

S&F in rep chromium plated jet for WC with 1.00 M long PVC pipe including necessary fittings complete all as specified and directed.

M&L for removal of plant growth by injection with chemical glyphosphate solution (4% concentration) @ 20ml or till refuse by cutting or injection in stem of plants or roots at 30mm. The area shall then be sprayed with solution 25ml glyphosphate (4% concentration) diluted with 1ltr of water.The size of block considred as whole bldg. All roots of plants shall be removed completely and making good the disturbed surface and painted with cement base paint or acrylic paint all as specified and directed.

Dismantling cast iron pipe pipes, jointed in cement mortar of any dia upto 100mm. all as specified.

S&F cast iron soil, waste and vent pipes (sand cast) 100mm bore in any length with or without ears with cement joints fixed to walls duly apply a coat of bitumenous black paint complete all as specified and directed.

S&F cast iron soil, waste and vent pipes (sand cast) 75mm bore in any length with or without ears with cement joints fixed to walls duly apply a coat of bitumenous black paint complete all as specified and directed.

S&F in rep Cast iron bend (any radius) diminishing pieces or tapers 100mm bore fitted with oval access door. all as specified.

S&Fin rep Cast iron bend (any radius) diminishing pieces or tapers 75mm bore fitted with oval access door.

S&F in repairs 32/40mm dia PVC waste pipe for WHB & sink with union complete all as specified.

E/M Portion S&F in repair sheet metal enclosure with single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps 'C' curve, 240 Volt complete all as specified & directed

S&F in repair MCB DB, single pole and neutral with 200 Amps rated bus bar, 230 volts, glazed, double door type, IP-43, including connecting all connections of wire to MCBs with proper lugs & making good to the disturbed surface complete for the following no of way :-

S&F in repair MCB DP/SPN, 240 Volts, AC, breaking capacity 10 KA, 'C' curve and connections by using suitable copper lugs complete of following rating :-

S&F in repair MCB SP, 240 Volts, AC, 6 to 32 amps, breaking capacity 10 KA, 'C' curve and connection by using suitable copper lugs complete

S&F in repair MCCB 4 Pole, 415 volt, AC, fixed type, with breaking capacity 16 KA suitable for load line DB & connection complete of following rating :-

63 amps rating

100 amps rating

S&F in repair of modular switch 10 amps, one way, single pole one module, 230 volts

S&F in repair of modular switch 10 amps, 2 way, single pole one module, 230 volts

S&F in repair of modular socket ,10 Amps, 5 pin, 2 module, 230 volts

S&F in repair of modular switch 16/20 amps single pole one module, 230 volts

S&F in repair of modular socket 16/20 amps, 2 module, 230 volts

S&F in repair of modular bell push with indicator 6 amps, one module

S&F in repair of modular fan step regulator 120 watt 2 module , 230 volts

S&F in repair of modular type GI metal flush box 1.60mm thick incl making good to disturbed surfaces to match with the existing complete for following moduls :-

Two/ three Modular

4 Modular

8 Modular (2 rows of 4 module)

12 Modular (2 rows of 6 module)

S&F in repair of modular cover plate with frame for following sizes :-

Two modular

Three modular

4 Modular

8 Modular ( 2 rows of 4 module)

12 Modular ( 2 rows of 6 module)

S&F in repair LED Bulkhead luminaire 10 watt, of polycarbonate housing and enclosed with acrylic diffuser IP-65 protection incl connection complete all as directed

S&F in repair LED Post top lantern luminaire with die cast aluminium spigot, lid cover and clear acrylic cover 40 watt, 5700 K with IP-65 protection incl connection complete.

S&F in repair wall mounted LED batten with aluminium housing and initigrated electronic drive 18/20 watt fixture 4 feet provided for efficient heat dissipation with polycorbonate diffuser and integrated electronic driver and all accessories pre-wired including connecting up with twin core flat flexible copper conductor cable of suitable size complete

S&F in repair surface and wall mounted LED batten 10 watt 2 feet long extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffusser and integrated electronic drive, pre-wired including connecting up with twin core flat flexible copper conductor cable of suitable size complete

S&F in repair highly efficient round shape downlighter 25 watt, 240 volt, CCT 5700 K with driver suitable for ceiling cutout 225 mm dia incl connection complete

S&F in repair surface/ceiling mounted LED panel type of size 2ft x 2ft, 36W, 230V, 5700K complete with driver full window glarefree opal diffuser LED panel with CRCA powder coated white housing complete with all accessories required for connection and making good the disturbed ceiling complete (Make- Havells cat Part No- PLUTOSURFACE2X2PLS36WLED857S/ Wipro cat part No- CRCO10R038HP57GL1 / Phillips Cat part no- SM365C LED32-6500 PSU OD WH)

S&F in repair LED flood/security light fitting of 30 watts with pressure die-cast aluminium housing complete with all accessories, fixing of fitting on wall with necessary fixing arrangement as required at site & connection complete all as specified & directed

S&F in repair fresh air ventilating Fan 200/250 mm sweep, 230V, AC, plastic body with louver shutter etc complete and connection from ceiling rose to fan terminal incl cutting of hole at wall for required size and making good disturbed surface complete

S&F in repair exhaust fan 300 mm sweep, 230V, AC, steel body with louver shutter etc complete and connection from ceiling rose to fan terminal incl cutting of hole at wall for required size and making good disturbed surface complete all as directed

S&F in repair wall mounting fan 400 mm sweep, adjustable, plastic blade grill for protection, pull cord control for speed and oscillation on-off, ABS body incl connection complete (Make- Havells/Khaitan/Usha)

Excavation in trenches not exc 1.5 Mtr wide and n.exc 1.5 mtr in depth, getting out for electric cable complete in any type of soil complete

Removing surplus excavated soil to a distance n.exc 50 mtr and depositing where directed at a level n. exc 1.5 mtr above starting point

Returning, filling in, soil obtained from excavation including spreading, levelling, watering and well ramming in layers n.exc 25cm thick complete

Supply and laying sub class 'B' bricks laid dry and flat across the length of cable for protection of cable complete

M&L for sand cushioning for protection of cable with screen wash river sand complete

Supply and laying or fixing or passing through pipe in repair of 1100V grade, heavy duty cable with XLPE insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of following size

10 sqmm 2 core

16 sqmm 4 core

25 sqmm 3.5 core

M&L for earthing with Galvanised Steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground vertically at a depth not less than 2.25metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using GI wire of size 4mm dia as earthing lead (upto the body of the equipment) by means of GI bolts, nuts, check nuts and washers and thimbles and protected by light grade 40mm dia GI pipe connected to main switch board or main control board and GI pipe medium grade 20mm bore for watering and including funnel, wire mesh, RCC pit cover and PCC chamber pit with PCC (1:3:6) type C-2 using 40mm graded stone aggregate, including excavation and earth work in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance not exceeding 50m all as specified and shown in electrical plate No 5 of SSR 1991(Part-I) complete

S&F in repair Plug top, 3 pin, 05 amps, 230 volt complete

S&F in repair Plug top, 3 pin, 15 amps, 230 volt complete

S&F in repair fan motor kit assembly for 500mm sweep, single phase, 145 watt, 230 volt, AC, 50 Hz, copper wound with three speed control and blade for desert cooler complete all as directed

S&F in repair of precast RCC earthing pit with CI cover, including angle iron frame made out of 35x35x4mm thick for supporting the edges of pit cover as dimension shown in Electrical plate No-2 of SSR part-I complete all as directed

M&L in repair for loop junction box, outdoor type, size 30cmx20cmX15cm, made out of engineering plastic one piece moulding type, bus bar rating 63 amps 4 strips aluminium with bus bar mounting colour R, Y, B, N on DMC unbreakable insulator with cable entry main supply from bottom side and pole light connection from back side, simens grey colout, shock proof, rust proof, fire retardant, having front opening and locking arrangement with MCB SP 10 amps - 01 No, box duly fixed on the pole with flat iron clamp of size 25 mmX3mm with nuts & bolts complete all as specified and directed (Note : Cost of incoming& outgoing cable lugs & glands of suitable size deemed to be included in the quoted rate) (Make : Unilac / Universal Switch Gear Control / Sintex / Tricolite)

S&F desert/Air cooler of body size 25"x25"x32", made out of corrosion resistant, 18 SWG GI sheet duly powder coated paint with 500mm sweep, copper wound fan motor kit of not less than 145 watt with metallic blade, ISI marked, 1400 RPM, 230 volt AC, tank capacity not less than 100 ltr, incl plastic submersible pumps, electronis fan regulator with P/switch, desert cooler to be fitted with 6mm thick plywood to cover the gap as required size at existing window and old/unsv desert cooler depositing in E/M Store yard complete all as directed

S&F in repair aesthetically designed energy saving LED wall light ,14 watt, white powder coated CRCA housing and PS diffuser, CCT 6500 K incl connection complete all as directed

M&L for painting of security watch tower MS structure of size 4m X 4m X 12m, having four vertical MS angle columns with bracing, supports MS flats & horizontal supports etc with one coat of red oxide and two coat of synthetic enamelled paint after preparation of surfaces complete all as specified and directed

M&L in repair of existing MS watch tower with replacing old/badly rusted and unserviceable MS angles/MS chanels/MS flats, clamp etc including fabrication, cutting, welding and bending as per site requirement to get required size of MS work incl painting with two coat of synthetic enamelled paint over one coat of primer complete all as specified and directed

S&F lamp holder, 230 volt AC, PVC / Polycarbonate type with back plate suitable for batten fitting including 9 watt LED bulb inverter type upto 4 Hrs back up 6500 K complete all as specified & directed

Sch of Credit- Total contract sum shall be calculated after deduction of Sch of Credit amount Credit amount - 64494.00

S GOURAV PRAKASH ENTERPRISES

QUALITY CONSTRUCTIONS CO

ANSH VANSH CONSTRUCTION COMPANY

Simran construction Company

friends associeates

M.S. ENGINEERING & CONSTRUCTION