Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹33.4 CrAdmitted-Finance | ₹33.4 Cr | L1 | Admitted-Finance |
| 2 | L2₹41.3 CrAdmitted-Finance | ₹41.3 Cr | L2 | Admitted-Finance |
| 3 | L3₹43.0 CrAdmitted-Finance 14 BILASIPARA P O P S BILASIPARA DIST DHUBRI ASSAM PIN 783348 | DHUBRI | ASSAM | 783348 | ₹43.0 Cr | L3 | Admitted-Finance |
| Sl No | Description | Qty | Unit | M.P.KHAITAN L1 | VSK INFRASTRUCTURES PRIVATE LIMITED L2 | Shree Gautam Construction Co. Ltd. L3 |
|---|---|---|---|---|---|---|
| 1.00EARTH WORK | ||||||
| 1.10 | Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth , 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m as directed by Engineer - in - Charge.
All kinds of soil. | 1,357.53 | cum | - | - | - |
| 1.20 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms,depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth,including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil
Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia. | 2,300 | metre | - | - | - |
| 1.30 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. | 224.53 | cum | - | - | - |
| 1.40 | Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials.
All kind of soil | 230.75 | cum | - | - | - |
| 1.50 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. | 99.8 | cum | - | - | - |
| 1.60 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m
outside the periphery of the area cleared. | 3,965 | sqm | - | - | - |
| 2.00CEMENT CONCRETE WORK | ||||||
| 2.10Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : | ||||||
| 2.20 | 1:4:8 ( 1Cement:4 coarse sand:8 graded stone stone aggregate. 40 mm nominal size | 400.84 | cum | - | - | - |
Tender Value
₹35.9 Cr
EMD Value
₹71.8 L
Closing Date
6 Feb 2020, 3:00 pmClosed
Rajeev Sood
General Manager Technical NHIDCL, 3rd Floor, PTI building 4, Parliament Street, New Delhi-110001
Construction of North East Regional Office of National Highways and Infrastructure Development Corporation Ltd. at Guwahati, Assam.
2019_NHIDC_529960_1
NHIDCL/GHY-RO-Building/2015
Open Tender
Civil Works - Buildings
550 days
Guwahati
Please refer Tender documents.
5 documents required · 5 mandatory
₹10,000
MD NHIDCL
₹71.8 L
NHIDCL HQ
21 Apr 2020
23 Dec 2019
7 Feb 2020
23 Dec 2019
6 Feb 2020
23 Jan 2020
23 Dec 2019 - 17 Jan 2020
17 Jan 2020
Amount
EARTH WORK
Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth , 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m as directed by Engineer - in - Charge. All kinds of soil.
Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms,depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth,including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.
Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. All kind of soil
Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.
CEMENT CONCRETE WORK
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
1:4:8 ( 1Cement:4 coarse sand:8 graded stone stone aggregate. 40 mm nominal size
1:5:10 (1 Cement : 5 coarse sand (Zone III : 10 graded stone aggregate 40 mm nominal size)
Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor,etc., up to floor five level, excluding the cost of centering, shuttering and finishing : 1:2:4 (1 Cement : 2 coarse sand (Zone III ): 4 graded stone aggregate 20 mm nominal size).
REINFORCED CEMENT CONCRETE WORK
Centering and shuttering including strutting, propping etc. and removal of form for :
Foundations, footings, bases of columns, etc. for mass concrete.
Walls (any thickness )including attached pilasters, butteresses, plinth and string courses etc.
Suspended floors, roofs, landings, balconies and access platform
Shelves (Cast in situ)
Lintels, beams, plinth beams, girders, bressumers and cantilevers
Columns, Pillars, Piers, Abutments, Posts and Struts
Stairs, (excluding landings) except spiral-staircases
Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like
Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured): Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level: Thermo-Mechanically Treated bars of grade Fe-500D or more.
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level: Thermo-Mechanically Treated bars of grade Fe-500D or more.
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/recoverable separately).
All works upto plinth level
All works above plinth level upto floor V level
All works above xtra for R.C.C./ B.M.C/ R.M.C. work above floor V level upto Terrace
Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable /recoverable separately.
Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum)
Providing M-35 grade concrete instead of M-25 grade BMC/ RMC. (Note : Cement content considered in M-35 is @ 350 kg/ cum)
Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-InCharge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical locations in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in- Charge. (Material shall conform to ASTM 6063).Floor Joint of 100 mm gap
Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall conform to ASTM 6063.): Wall Joint of 100 mm gap
Providing and fixing of expansion joint system of approved make and manufacture for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates as per ASTM B221-02. The system shall be such that it provides water tight roof to roof /roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement.(Material shall confirm to ASTM 6063.)Roof Joint of 100 mm gap
MASONRY WORK
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)
Extra for brickwork /AAC Block masonary in superstructure above floor level V level , for each four floors or part there of by mechanical means.
Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means.
Brick work with non modular fly ash bricks conforming to IS:12894,class designation 10 average compressive strength in super structureabove plinth level up to floor V and above level in : Cement mortar 1:6 (1 cement : 6 coarse sand).
Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above plinth and upto floor V level and above: Cement mortar 1:4 (1 cement :4 coarse sand).
CLADDING WORK
GRANITE SKIRTING (IN ALL STAIRCASES & FLOORS) Granite work gang saw cut (polished and machine cut) of thickness 18 mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately). Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble : Area of slab upto 0.50 sqm
GRANITE COUNTERS (IN KITCHEN, PANTRY & ALL TOILET AREAS) Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade: Area of slab over 0.50 sqm.
GRANITE EDGE MOULDINGS FOR COUNTERS Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc.. Complete as per design approved by Engineer-in-Charge : Granite work
EXTERNAL STONE WORK Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately).White sand stone - 30mm thick gang saw cut stone.
STRUCTURAL STEEL FRAME (FOR FIXING OF DRY CLADDING) Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut with machine cut edges sand stone) on walls at all heights using M.S. square/ rectangular tube in the required pattern as per architectural drawing, including cost of cutting, bending, welding etc. The frame work shall be fixed to the wall with the help of M.S. brackets/ lugs of angle iron/ flats etc. which shall be welded to the frame and embedded in brick wall with cement concrete block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) of size 300x230x300 mm, including cost of necessary centring and shuttering and with approved expansion hold fasteners on CC/RCC surface, including drilling necessary holes. Approved cramps/ pins etc. shall be welded to the frame work to support stone cladding, the steel work will be given a priming coat of Zinc primer as approved by Engineerin- charge and painted with two or more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the Engineer-in-charge for approval before execution). The frame work shall be fixed in true horizontal & vertical lines/planes. (Only structural steel frame work shall be measured for the purpose of payment, stainless steel cramps shall be paid for separately and nothing extra shall be paid).
STAINLESS STEEL CRAMPS WITH NUTS,BOLTS & WASHER Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge.
CERAMIC WALL TILES, SKIRTING & DADO Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
GLASS REINFORCED CONCRETE (GRC) WALL CLADDING TILES Providing and fixing of Glass Reinforced Concrete (G.R.C) Wall Cladding Tiles in approved design, size, texture, thickness, pattern and color. The thickness of the tiles should range between 12 to 18 mm (depending on the texture of the tile), allowing variance of ±2 mm in accordance with IS: 1237-1980. The composition of tiles should be ‘43’ Grade White Portland cement, reinforced with Alkali Resistant Glass Fiber and the pigmentation should be done with exterior grade synthetic inorganic iron oxide pigments manufactured by ‘BAYFERROX (Germany)’ or equivalent. The pigmentation should be homogeneous and in accordance with British Standards BS EN 12878:1999. The other additives should be fine washed graded quartz, super plasticizers and integrated water proofing agents and others. The tiles should be produced with high vibration technology and should have compressive strength equivalent to M-40 Grade@28 days. The top surface of the tiles should be sealed with acrylic lacquer resulting in surface water absorption of tiles, less than 1% and water absorption by 24 hrs immersion method, less than 8%. The tiles should be applied on a rough plaster of cement mortar 1:3 (1 cement: 3 coarse sand) and the fixing of tiles should be done by tile adhesive or equivalent as per manufacturer’s laying instruction.GRC Wall Cladding Tiles.Pattern: Unibrick country Brick. Size: 7.5" x 2.25. Colour-Copper Red
WOOD AND P.V.C WORK
DOOR FRAMES Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately): Second class teak wood.
Providing wood work in frames of partitions / panelling etc 1"X2"Battens sawn and fixed in position with necessary stainless steel screws etc. : Salwood
FLUSH DOOR SHUTTER Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.
M.S. SLIDING DOOR BOLTS Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm.
MORTICE LATCH LOCK & HANDLES Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.
DOOR STOPPER / BUFFER Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.
TOWER BOLT Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300X10 MM
Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted withintumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).
Supplying Dash fastener / Chemical fastener
Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge
Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.
STAINLESS STEEL HANDLE Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete: 125 mm
Providing and fixing UPVC (un-plastisized polyvinyl chloride) sliding windows size 2400w x 2070h (53.48 sqft) complete in all respect with specification of SY05 Combination System,Combination System, 6.0mm+12mm air gap +6mm thick toughened glass, White colour,I-60 Slider Series Coupling 180 - 40107-01400, Full Reinforcement, Channel Reinfof type, 1.5mm Rein thick frame , 2.00mm Reinf thick Sash, White Frame colour , Window O/F: 41101-11000,Slider O/F : 41201-01000,Mechanical T-Joins, 74mmFrame T/M Stan., White Sash Colour, Slider Sash : 41201-03000, Slider Screen-: Track + Screen, Super Screen Sas type,White Handle Colour,: Grooved SL Alumi Rail, Patio sliding Handle,SS430 (CS) Espag. Type,White Bead Colour all complete as per drawing Fixing should be done as per Approved brand specifications.
Providing and fixing UPVC (un-plastisized polyvinyl chloride) sliding windows size 1200w x 2070h (26.74 sqft) complete in all respect with specification of SY05 Combination System,Combination System, 6.0mm+12mm air gap +6mm thick toughened glass, White colour,I-60 Slider Series Coupling 180 - 40107-01400, Full Reinforcement, Channel Reinfof type, 1.5mm Rein thick frame , 2.0mm Reinf thick Sash, White Frame colour , Window O/F: 41101-11000,Slider O/F : 41201-01000, White Sash Colour, Slider Sash : 41201-03000, Slider Screen-: Track + Screen, Super Screen Sas type,White Handle Colour,: Grooved SL Alumi Rail, Patio sliding Handle,SS430 (CS) Espag. Type,White Bead Colour all complete as per drawing Fixing should be done as per Approved brand specifications.
Providing and fixing UPVC (un-plastisized polyvinyl chloride) sliding windows size 600w x 2070h (13.37 sqft) complete in all respect with specification of SY05 Combination System,Combination System, 6.0mm+12mm air gap +6mm thick toughened glass, White colour,I-60 Slider Series Coupling 180 - 40107-01400, Full Reinforcement, Channel Reinfof type, 1.5mm Rein thick frame , 1.5mm Reinf thick Sash, White Frame colour , Window O/F: 41101-11000, White Sash Colour, C'ment T- Sash : 41101-13000, ,White Handle Colour,Casement Handle - Espag, SH Friction hinge type, SS Friction Hinge,SS430 (CS) Espag. Type, White Bead Colour all complete as per drawing Fixing should be done as per Approved brand specifications.
Providing and fixing UPVC (un-plastisized polyvinyl chloride) sliding windows size 900w x 2070h (20.05 sqft) complete in all respect with specification of SY05 Combination System,Combination System, 6.0mm+12mm air gap +6mm thick toughened glass, White colour, Coupling 180 - 40107-01400, Full Reinforcement, Channel Reinfof type, 1.5mm Rein thick frame , 1.5mm Reinf thick Sash, White Frame colour , Window O/F: 41101-11000, White Sash Colour, C'ment T- Sash : 41101-13000, ,White Handle Colour,Casement Handle - Espag ,SH Friction hinge type,SS Friction Hinge,SS430 (CS) Espag. Type,White Bead Colour all complete as per drawing Fixing should be done as per company specifications.
Providing and fixing UPVC (un-plastisized polyvinyl chloride) sliding windows size 750w x 2070h (16.71sqft) complete in all respect with specification of SY05 Combination System,Combination System, 6.0mm+12mm air gap +6mm thick toughened glass, White colour, I-60 Slider Series ,Coupling 180 - 40107-01400, Full Reinforcement, Channel Reinfof type, 1.5mm Rein thick frame , 2.0mm Reinf thick Sash, White Frame colour , Window O/F: 41101-11000, Slider O/F -41201-01000,White Sash Colour, Slide Sash : 41201-03000, Slider Track+Screen,Super Screen Sas Type,White Handle Colour,Grooved shape SL Alumi rail,Patio Sliding handle,SS430 (CS) Espag. Type,White Bead Colour all complete as per drawing Fixing should be done as per Approved brand specifications.
VENTILATORS Providing and fixing UPVC (un-plastisized polyvinyl chloride) ventilator size 900w x 900h (8.72sqft) complete in all respect with specification of SY01 Combination System,Combination System, 6.0mm+12mm air gap +6mm thick toughened glass, White colour, I-60 Int. Glz. Sys,Tilt/Turn F ,White colour, Full Reinforcement, Channel Reinfof type, 1.5mm Rein thick frame , White frame colour,Window O/F -41101-11000,White Bead Colour all complete as per drawing Fixing should be done as per Approved brand specifications.
Providing and fixing UPVC (un-plastisized polyvinyl chloride) ventilator size 600w x 600h (3.88sqft) complete in all respect with specification of SY01 Combination System,Combination System, 6.0mm+12mm air gap +6mm thick toughened glass, White colour, I-60 Int. Glz. Sys,Tilt/Turn F ,White colour, Full Reinforcement, Channel Reinfof type, 1.5mm Rein thick frame , White frame colour,Window O/F -41101-11000,White Bead Colour all complete as per drawing Fixing should be done as per Approved brand specifications.
FULLY AUTOMATIC SLIDING DOOR Providing and fixing Automatic Sliding glass door operator 4150mm , compliant with future European standards and produced according to the guidelines for power-operated windows, doors and gates, BGR 232, the UVV and the VDE regulations. TÜV design tested, tested according to the low voltage guidelines, fulfils DIN 18650 standards, for framed glass door application with 12mm tougned glass for 2 Nos sliding door panels and 2 Nos fixed panels, both sliding Operator & Frame Finish should be Silver Anodised E6/C0, with operator dimensions (H x D) : 100 x 180 mm and of length as required to suit the opening size given below. TThe track profile should be separate from the main profile for enabling reduction in vibration insulation. Microprocessor-controlled control unit, Self-learning, with adjustable parameters for opening and closing speed, hold-open time and opening and closing force, reversing when obstruction is encountered, Class of protection IP 20. Activators- 6 Safe Combinations Radars with Motion & Presence Detection (02 Nos), Light barrier comprising of receiver and transmitter - 01 Pair, with Electro-mechanical locking, Program Switch with Key. Max Panel Weight Carrying Capacity of 2 X 100 Kgs. tem shall have constant power supply 230V+ 5%, 50Hz, AC . The requirement in total is as mentioned ,wall cconneting profiles be used on top of overpanel and on all sides to fixed panels only .The above work should complete in all respect as per approved drawings and to the satisfaction of Architect /Engineer-in-Charge. (Note: For 100% power back up we have D.G Set)
GLASS DOOR Supply & Fixing of Glass Door (Single Leaf) size 0f 2100 mm x 1050mm of 10mm toughened glass with Slim line 45mm frames clip in profiles all around the door with complete assembly . DP45 Door Profile frame of size 45X50mm with seals with Junior Office Hinges (3nos) & Studio Gala Locks (1no) & Studio Gala lever handles in aluminium silver (EV1) finish , Euro profile cylinder and TS 89 Door closer with slide channel (as per EN 1154) and saddle plate for fixing on the Glass door and necessary seals to be provided all around the door frames. The slim line profiles shall be suitable for Glass thickness of 10mm .The Profile shall be matt natural anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system. All Profiles to be with 2 mm Gauge thickness Excluding 20 Micron of Anodizing.
FULL HEIGHT GLASS PARTITIONS Supply and Fixing of Glass partition of 10mm Toughened Glass using slim line System-45 Frames clip in profile to a height of maximum 3m or as per drawing.The Fixed glass to be fixed using BP45 Profiles at Top & Bottom & fixed frame cleat . The profile size to be 45x25MM to be fixed on to the floor/ ceiling as per the architect design. H Junction profile to be used at all Glass to Glass vertical joints, 90 Deg L Junction Profiles and T Junction profiles necessary as per design.In case of Glass overall panel MP45 & BP45 Overpanel Profile to be used. The clip in profiles shall be suitable for Glass thickness of 10 mm .The Profile shall be matt natural anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system. All Profiles to be with 2 mm Gauge thickness Excluding 20 Micron of Anodizing.
FULL HT. PARTITION Providing and fixing 69 mm thick of Approved brand drywall partition system, which include "Approved brand Steel" G.I framework (180GSM Galvanizing; 345 Mpa Yield Strength), comprising of 51mm Floor and Ceiling track profile, 0.5mm thick, having two equal flanges of 32mm, fixed to the floor and ceiling, in plumb with each other, with sleeves and screws at 610mm; Vertical G.I studs of size 51mm, 0.5mm thick, having one flange of 42mm and another flange of 44mm and two equal lips of 5mm insert fixed into the track profiles at 610mm centers. 9mm Approved brand Heavy Duty Fibre Cement board (Confirming to IS 14862; Type - B) are screw fixed to the either sid of the framework with 25mm drywall screws, respectively, at 300 mm centers. Rate shall be inclusive of Glass wool of 48kg/m3 density and 50mm thickness that has to be placed in between the cavity of frame. Jointing and Finishing: Finally edges of the board are to be jointed and finished so as to have a flush look which includes filling and finishing with Approved brand compound of standard. make with Self adhesive Fiber glass mesh tape. The rate shall be inclusive of providing & finishing 2 coats of top paint and labour for cutouts for light fixtures, AC grills,diffusers etc,
LOW HT. PARTITION Providing and fixing 69 mm thick X1350 mm height , approved brand drywall partition system/ approved equivalent, which include "Approved brand Steel" G.I framework (180GSM Galvanizing; 345 Mpa Yield Strength), comprising of 51mm Floor and Ceiling track profile, 0.5mm thick, having two equal flanges of 32mm, fixed to the floor and ceiling, in plumb with each other, with sleeves and screws at 610mm; Vertical G.I studs of size 51mm, 0.5mm thick, having one flange of 42mm and another flange of 44mm and two equal lips of 5mm insert fixed into the track profiles at 610mm centers. 9mm approved brand Heavy Duty Fibre Cement board (Confirming to IS 14862; Type - B) are screw fixed to the either side of the framework with 25mm drywall screws, respectively, at 300 mm centers. Rate shall be inclusive of Glass wool of 48kg/m3 density and 50mm thickness that has to be placed in between the cavity of frame. Jointing and Finishing: Finally edges of the board are to be jointed and finished so as to have a flush look which includes filling and finishing with approved brand compound of std. make with Self adhesive Fiber glass mesh tape. The rate shall be inclusive of 2 coats of top paint and labour for cutouts for electrical, telephone,computer conduites etc.
1-(F) UNICOLOR LAMINATE: Providing ,fixing Uni + unicolour decorative laminate with homogeneous same color of decorative surface and core layers as per 438:3 -2005, FSC & Green Guard . Item to be completed in all respects as per drawings and instructions from Project in charge .
1-(B))MR+(MAR RESISTANT)TUFF GLOSS LAMINATES Providing ,fixing Merino MR+(Mar Resistant)Tuff Gloss Laminates 1mm thickness , conforming to IS 2046:1995, 3to 4 times more resistant than normal Gloss Laminate, gloss meter reading is over 110 at 60 degree angle reading as per ASTM D6037-96 . Item to be completed in all respects as per drawings and instructions from Project in charge.
9.75mm THICK MDF EXTERIOR GRADE PLAIN PARTICAL BOARD Providing and fixing MDF Exterior grade plain partical board of approved makes: Plain Exterior Grade MDF Boards of 9.75mm thickness, Exterior grade wood base (Grade-I), Melamine Bonded, Stamped IS 12406. All accessories, screws, fixing implements , labours, material and all lifts. Item to be completed in all respects as per drawings and instructions from Engineer in charge.
12 mm THK. 710 BWP PLY Providing and fixing partition skinning with avg 12 mm thk BWP Grade Plyboard IS 710 BWP grade on over Al. skeletal frame/wooden frame , as approved by Architect. Plywood shall be 12mm thick, non-decorative, factory made as per IS:710 and should be ISI marked and be made of non-coniferous timber red hard wood with moisture contents not more than 12% and dimension as given in IS code. The panel comprising of plywood should be 9 ply construction and cross bend and panel core shall be glued by hot pressed with Quadra process, while the thickness of face veneer (Okume/Gurjan) shall not be less than 0.5mm. all core shall fully confirm to the requirement specified in the IS code. All timber used should be well seasoned and chemically treated. Adhesive used shall be phenol formaldehyde synthetic resin BWP type specified in IS:848-1974. All dimensions shall be finished dimension and manufacturers test certificate for test specified in IS:710 shall be rendered.” Item shall be complete in all respect.
CHANNELED WOODWORKS WALL PANELLING OF SIZE: 192X2400X15MM Providing and Fixing Channeled Woodworks perforated panels of width 192mm, thickness of 15mm and length 2400 mm or as required by the Architect/ approving engineer, made of a Moisture Resistant fibre board with minimum 595 Kg/M3 density substrate with a laminated facing as per the approved shade & finish and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the visible surface has a “Helmholtz” fluted perforation of 3mm width and 13mm of visible panel each. The edges of the panels shall be “tongue-and-grooved” to receive special clips for installation. The back of the perforated panel shall have sound absorbing non-woven acoustical fleece having NRC of 0.59. The panels shall be mounted on special aluminium splines (keel) using clips provided by Approved brand and approved by the Architect/ Engineer-in-Charge. INSTALLATION: Install wooden battens (provided by others) of section 50x50mm or as approved by the Architect on the solid wall horizontally using screws and plugs at spacing of 600mm centre-to-centre. Screw the aluminium extruded keel for channelled woodworks provided by Approved brand over the lowest and second wooden batten at an on-centre distance of 600mm. Install the Skirting (provided by others) of width 50mm or more as required by the Architect/ Engineer-in-Charge and insert the tongue end of the panel in the skirting. Place the inside clip on the groove end of the panel along the Al keel and then place the tongue end of the next panel. Continue installing rows of panels by inserting the tongue into the groove of the earlier inserted panel and progressively installing inside clips into the next keel till the actual height is achieved. Finish off the edges using wooden moulding of matching colour (provided by others). Installation to be carried out by Approved brand Trained Installation team & Installation should be carried out as per Approved brand recommended procedure.
OPTRA ACOUSTICAL WALL PANELING Providing and supplying ‘Optra Acoustical Wall Paneling’ of approved brand with square edges made of fibre glass substrate 25mm thick and wrapped on the front side with an acoustically transparent and classified for Fire reaction Class A as per ASTM E-84, fabric with an option of colors – Husk, Copper, Sangria, Sesame, Coffee, Charcoal, Titanium, Flame, Peanut & Shell as per the choice of the Architect of size 600X600 mm providing a minimum sound absorption level of 0.85 NRC to be affixed to wall using Wall panel impalers supplied by approved brand and construction adhesives as per the instructions laid down by the manufacturer. INSTALLATION: 4nos. of approved brand wall panel Impalers of shall be fixed to the wall surface using self-tapping screws. Silica based construction adhesive to be dabbed on to the projecting elements (spikes) of the impalers. Approved brand Optra wall panels shall be pierced through the spikes of the impalers ensuring the line and level of the panels are maintained. Installation to be carried out by approved brand Trained Installation team & Installation should be carried out as per approved brand recommended procedure.
ARTIFICAL GREEN WALL Providing testing and commissiong of Artificial boxwood matt is a matt prepared with synthetic PVC leaves made to look like actual plant for vertical applications both in indoors & outdoors. The main reason for usage of this matt is maintenance-Artificial matt stands up to heavy use and requires no irrigation and trimming and no sunlight but only requires periodic cleaning if used in interiors. Since major cities across globe are turning into concrete jungles with very less space for greenery, so artificial green matt in different leave patterns which almost look real is best solution to create a soothing green effect without any maintenance. For exterior applications UV matt are recommended for long life Application is done using rubber adhesive or by simply hanging matt on walls with screws giving a long lasting installation. Further artificial flowers or bushes to be added in matt to give more natural look as per requirement. TechArtz Global is major importer of this material from Germany & China to India. The Rate shall be includive of providing and fixing SS Fastner of 10mmdia. and 100mm Long (IS code) duly Fixed the ply to Wall .
STEEL WORK
Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/c making provision for fixing glass if required and fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)
FLOORING
RECTIFIED GLAZED CERAMIC FLOOR TILES Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.
VITRIFIED FLOORING Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified tiles matt/ antiskid finish of size. Size of Tile 600x600 mm.
VITRIFIED SKIRTING Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete: Size of Tile 600x600 mm.
VITRIFIED WALL TILES/ DADO Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 800x800 mm.
GROUTING the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in charge. Size of Tile 800x800 mm.
Providing and fixing removable raised/false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug. b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-charge. c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be corrosion resistant epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and, an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure the quality of the product: 300 mm Finished Floor Height (FFH)
FLAMED GRANITE FLOORING (IN PARKING AREAS) Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
GRANITE FLOORING Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge: Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
TEXTURE LAMINATED WOODEN FLOORING Providing and laying of 8mm thick AC5 grade textured laminated wooden flooring (as/ EN 13329) , including 100mm high skirting with 0.2mm thick direct laminate on top of specially developed substrate core of planks size 1288mm x196mm having smart lock tongue and grove construction with edges dullly impregnated to secure long lasting joints secure together confirm to EN 13329. the approved decorplanks to be placed on a 0.2 mm thick alkali resistant polyethylene foam (density 3920-935kg/m3) with a 1.5mm thick extruted polythylene foam( density 30-32 kg/m3 ) on top to secure the floating floor to resist any moisture movement from the sub floor on top to secure the floating instalation . the skirting is to be secured with the help of matching wall based ,60mm high, with t-profile &reducer/ beading . the instalation at site has to be done by company trained and approved inatallers. all complete as per instructions from engineer-in-charge.( the item icludes skirting &all necessary profiles,beading etc. complete in all respect).
VINYL FLOORING Sports flooring of Vinyl flooring polaris consists of following specifications for Badminton court, General performance sports flooring,shock absorption, vertical deformation,vertical ball behaviour,resistance of rolling load,resistance to wear ,specular gloss having overall thickness 6.5mm weight 4200 g/sqm sheet size 1.5m width & 10m length shall all be conforming to BS EN 14904.h shall all be conforming to BS EN 14904.
Providing and fixing of Glass Reinforced Concrete (G.R.C) Flooring Tiles in approved design, size, texture, thickness, pattern and color. The thickness of the tiles should range between 22 to 25 mm, allowing variance of ±5 mm in accordance with IS: 1237-1980. The tiles should be made with M-40 Grade Concrete mix design having ‘43’ Grade White Portland cement, reinforced with Alkali Resistant Glass Fiber and the pigmentation should be done with exterior grade synthetic inorganic iron oxide pigments manufactured by ‘BAYFERROX (Germany)’ or equivalent. The pigmentation should be homogeneous and in accordance with British Standards BS EN 12878:1999. The other additives should be fine washed graded quartz, super plasticizers and integrated water proofers and others. The tiles should be produced with high vibration technology and should have compressive strength equivalent to M-40 Grade@28 days. The top surface of the tiles should be sealed with acrylic lacquer resulting in surface water absorption of tiles, less than 1% and water absorption by 24 hrs immersion method, less than 8%. The beds where the tiles are to be laid shall be clean, wet and mopped. The bedding for the tiles shall be 20mm thick and with cement mortar 1:3 (1 cement: 3 coarse sand) and it shall be spread properly and the usage shall begin only after 48 hours. GRC Paving Tile Pattern:-Weatherdale Size: 12"x12" Colour-Delhi Stone
ROOFING
Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.
Providing and fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Rockwool conforming to IS: 8183, density 48 kg/ m3, 50 mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5mm x 24 gauge wire mesh, for top most ceiling of building.
Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc. : 100 mm diameter
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.: Bend 87.5° 110 mm bend.
GYPSUM FALSE CEILING Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recomme-nded jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I
Providing and fixing to the inlet mouth of rain water pipe PTMT (an Engineering Thermoplastic) grating square (Slit) 150 mm square with a height of 8 mm and weighing not less than 100 gms
PLAIN PANEL SUN LOUVERS: Providing and fixing Plain Panel Sun Louvers of approved make having approved colour. The system shall consist of panel 84 mm wide X 16mm deep X 0.6mm thick with round edges panel length upto 6 Mtrs. The panel shall be coil coated on a continuous paint line double baked and roll formed enamelled corrosion Resistance Aluminium Alloy AA5050 (Al. Mg.) for higher strength and good roll forming characteristic. The Panel shall be clipped to Aluminium SL-4 panel stringer of Size: 33mm wide and 86mm deep X 0.95mm thick in a standard length of 5 Mtrs, made of double baked enamelled Aluminium Alloy AA 5050 (Al. Mg.) in white colour with cutouts to hold the panel in a module of 86mm C/C. The prongs on SL–4 stringers shall be to accommodate an angle of 21.30 Degrees between two panels. The first stringers shall be fixed at 150mm from both ends & thereafter at a distance of 0.75 to1 Mtr, depending on Wind Load. The Stringer shall be fixed to a suitable sub-structure with Nut/Bolt & Washer. All properties and specifications shall comply with ECCA directives and more specifically EN 1396:1996. Paint Finish: Panel shall be stove enamelled and finished with special three layered coating system of approved make (consisting of first a conversion layer of thickness 800-2000mg/sq mtr, a polyurethane basecoat of 16-20 microns, and a special top coat of polyamide particles of 8-12 microns thick to provide excellent abrasion and damage resistance) in a continuous coil coating process of the approved colour on the exposed side and the reverse side with epoxy.
GI METAL LAY IN BLACK GROOVE CEILING Providing & Fixing of GI Metal Suspended Ceiling System - Approved make In Perf. With fleece 600x600x0.5mm (MICROLOOK) EDGE TILES in global white colour to be laid on Black Groove 15mm wide T - section flanges color white having rotary stitching on the Main Runner, 1200 mm & 600 mm Cross Tees with web height of 38mm. The tiles should have Humidity Resistance (RH) of 100%, with Light Reflection of 62%, NRC 0.7. INSTALLATION: To comprise main runner spaced at 1200mm centres securely fixed to the structural soffit at 1200mm maximum centre. The First/Last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centres. SUSPENSION SYSTEM accessories supplied by Hilti consisting of HLC Sleeve Anchor Fasteners of thread size 6.5mm x 25/5 with Soffit Cleat made of Galvanised steel of size 27 x 37 x 25 x 1.6mm and Level Clip in dimensions of 85x30x0.8mm with 4.00 mm GI wire.
BAFFLE CLOSED Providing & fixing Vertical Linear Baffle Ceiling made out of Aluminum Extrusion in Aluminum alloy grade 6063. The baffle blade shall be in size of 100x 25 x 3600mm in Wood grain finish – Pradoo & Cabrueava. The baffle blade shall be suspended using Slotted U-profile at on-center spacing in multiples of 25mm. Longer lengths of Baffle to be connected by Baffle Joiner and the ends to be fixed with End caps. Installation of U-Grid: The U profile to be suspended at every 1200mm on-centre using 6mm threaded rod from the structural soffit using U-profile hanger. U-profile splice to be used to join more than one U profiles of length 3.75M. 1st U-Grid Channel must be no more than 400mm from the perimeter. Installation of Baffles: Locate the slot for Baffle Hangers in slot of Baffle section at 1200mm centres. Hangers are inserted into the slot, then rotated 90° and fixed into position by tightening the grub screw. Baffle to be lifted into position and hangers engage over lip of U-Grid Channel. Each Hanger to be secured into position by inserting the Locking Clip. Baffles blades to be connected at ends with Baffle Joiner, which are inserted into the top and bottom slots of the Baffle closed profile for alignment only. The bottom Joiner to be located first and fastened on one side only. The top Joiner to be fitted then and secured with grub screws on one side. Then the two Baffle sections shall be joined and the top Joiner is screw fastened on the 2nd Baffle profile. End Caps to be located by pushing the End Cap tongues into Baffle slots.
CELLIO OPEN CELL 100MM X 100MM ‘LAY-IN’ ALUMINIUM CEILING WITH 15mm GRID Providing and fixing in true horizontal level Cellio Open cell Aluminum lay-in ceiling tiles with border panels forming flush-tegular edge of size 600mmx600mmx38mm having Fire Performance CLASS 0/Class 1 (BS 476). The tile of ‘Global white’ color with cell size 100mm X 100mm shall be laid on white painted Suprafine XL15mm profile grid system comprising Main runners (3000mm), 1200mm and 600mm cross tees with 15mm white flanges and 38mm web height. The grid should be of “Approved” make with 15mm wide T - section flanges color white having rotary stitching on all T sections i.e. the Main Runner with C3 coupling, 1200 mm & 600 mm Cross Tees with Hardened XL2 Clip having a web height of 38 mm and a load carrying capacity of 14 Kgs/M. The T Sections have a Galvanizing of 90 grams per M2 with pull out strength of 100 Kgs. Suspension system is to be of Approved make. INSTALLATION: To comprise main runner spaced at 1200mm centers securely fixed to the structural soffit by approved hangers at 1200mm maximum centre & not more than 150mm from spliced joints. The last hanger at the end of each main runner should not be greater than 600mm from the adjacent wall. 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long cross tees centrally between the 1200 mm cross tees. Installation to be carried out by Trained Installation team & Installation should be carried out as per recommended procedure. Perimeter trim to be wall angles, secured to walls at 450 mm maximum centers. SUSPENSION SYSTEM accessories manufactured and supplied by Industries consisting of M6 Anchor Fasteners with Vertical Hangers made of Galvanized steel of size 26 x 26 x 25 x 1.2mm with a Galvanized Thickness of 80gsm, A pre Straightened Hanger wire of dia – 2.65 mm of 1.8 m length., thickness of 80gsm and a tensile strength of 344- 413 MPa, along with Adjustable hook clips of 0.8mm thick, galvanized spring steel for 2.68 mm. The adjustable clip also consists of a 3.5 mm aquiline wire to be used with the main runner.
SOUNDSCAPE BLADE 400X1200X40MM Providing and Fixing Approved SoundScapes – Blades which are 40 mm thick, pre-formed fiberglass blades with sizes of 200X1200mm, 200mmX1600mm, 400X1200mm, 400X1600mm,400X1800mm, 500mm X 1200mm and 500X1600mm with Dura brite finish on all sides and edges, Acoustical performance of 0.65 NRC in standard White color with Light reflectance 87%, or in the color specified by the Architect (Light Ivory, Pale Green, Pastel blue, Traffic Grey, Pale Brown) and Fire Performance Class B – s1, d0 as per En 13501-1.INSTALLATION WITH U-PROFILE HANGER: The U-profile of size 20mmX30mmX3750mm to be suspended based on the on-centre distance between the factory fitted spiral hooks on the blades. The on-centre distance between the factory fitted spiral anchors is length of the blade – 600mm. U profile to be suspended using 6mm threaded rod from the structural soffit no further than 450mm from each wall. U- Profile splice to be used to join longer lengths more than 3.75M. U- Profile hanger kit comprising of Blade hanger and snap hooks to be used to suspend the Blades to the U –profile. Blade hanger to be locked on the U-profile using the Locking clips on the square slots with on centre spacing in multiples of 50mm. Snap hooks to be fixed on the blade hanger. SoundScapes Blades to be installed on the snap hook by inserting the factory fitted spiral hooks into the snap hooks on both sides. Blade connector kit comprising of bottom connector and top connector to be used to join two blades side by side. Installation to be according to the instructions provided by manufacturer.
SOUNDSCAPE SHAPES - ACOUSTICAL CLOUDS (INDIVIDUAL SUSPENSION) Providing and Fixing Approved Soundscape - Acoustical clouds which are 30 mm thick, flat glass fibre panels with Humidity Resistance RH 90% & Recycled Content of minimum 30%, come in various shape options like Square and in standard Traffic White colour with LR 90% or in the color specified by the Architect / Engineer in charge (Ivory / Pale Green / Pastel Blue / Traffic Grey / Pale Brown). or in the color specified by the Architect / Engineer in charge (Ivory / Pale Green / Pastel Blue / Traffic Grey / Pale Brown) . The size and sound absorption details are as below: Square 1200x1200mm 2.48 The back of each panel to have embedded square frame bracket system of 610x610mm in which provisions are already made for integration of installation system for suspension of individual or grouped panels. INSTALLATION: The panels to be suspended individually using the Soundscape Deck hanging kit. Each kit to consist of gripper structure anchors, aircraft cables and bottom end cable adjusters. Each panel to be suspended using the aircraft cables which are suspended from the soffit using the gripper structure anchors and its other end passing through the bottom end cable adjuster which are screwed in the 4 corners of the frame bracket system. The height & level of the panels can be adjusted using the bottom end cable adjusters.
G.I LAY-IN PLAIN Providing & Fixing of GI Metal Suspended Ceiling System GI Lay In Plain Fleece 600x600x0.5mm (regular) EDGE TILES in global white colour to be laid on 24mm normal Grid 24mm wide T - section flanges color white having rotary stitching on the Main Runner, 1200 mm & 600 mm Cross Tees with web height of 32mm. The tiles should have Humidity Resistance (RH) of 100%, with Light Reflection of 62%. INSTALLATION: To comprise main runner spaced at 1200mm centers securely fixed to the structural soffit at 1200mm maximum center. The First/Last suspension system at the end of each main runner should not be greater than 450mm from theadjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm center to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centers. SUSPENSION SYSTEM accessories supplied by Approved make consisting of HLC Sleeve Anchor Fasteners of thread size 6.5mm x 25/5 with Soffit Cleat made of Galvanised steel of size 27 x 37 x 25 x 1.6mm and Level Clip in dimensions of 85x30x0.8mm with 4.00 mm GI wire.
“WOODWORKS GRILLE WITH DOWEL MADE OF NATURAL BAMBOO WITH 24MM PRELUDE 43 BLACK” SYSTEM Providing & fixing of woodworks grille with dowel made of natural bamboo with 24mm prelude 43 black exposed grid. The Woodworks (WW) Grille panel of nominal size 57x300x2400mm comprising 6 blades of 57x16x2376mm with on center spacing of 50mm fixed thru dowel of dia-12mm x 300mm with on center spacing of 300mm and additional end dowels at 150mm from both the edges. Ledger of 6.5x24x2400mm to be used for covering face of wall angle. WW Grille should comply with ASTM-E84: Class A and have Relative Humidity of RH70. The panels are UV coated to Natural or Carbonized shades. Optional : Open edges may be covered using “Edge Caps” of 66x19x2400mm and “Blade Junction” of 66x38x2400mm to be used along the connection of two WW Grille Panels. The grid should be of “Approved” make Prelude 43 with 24mm wide T - section flanges Black powder coating having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 43mm for the main runner & the Cross Tees and with a load carrying capacity of 20 Kgs/M2. Black dowel clips of spring steel to be used for fixing panel to suspension system. INSTALLATION: To comprise main runner spaced at 1200mm centers securely fixed to the structural soffit using Approved suspension system (specifications below) at 1200mm maximum center. The First/Last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm center to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 19x19x3000mm, secured to walls at 450 mm maximum centers.
PORTLAND MAPLE CEILING(WOODWORKS 600X600X18MM MICROLOOK EDGE TILES IN RG3003 (RG3) PERFORATION WITH 15mm SUPRAFINE 43 EXPOSED GRID”) SYSTEM : Providing & Fixing of Wooden finished Suspended Ceiling System with Woodworks Microlook edge tiles with 15mm Suprafine 43 exposed grid. The Tile in RG3003 (RG3) perforations having hole diameter as 3mm and open area as 3% with approved laminate finish with 0.7mm matching PVC edge banding and having an NRC of 0.42, Humidity Resistance (RH) of 70% in module size of 600mm x 600mm x 18mm and density of 725 Kgs/M3. The tile shall be laid on Suprafine 43 with 15 mm wide T - section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm and a load carrying capacity of 15.5 Kgs/M2 & pull out strength of minimum 100 Kgs.. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with Suspension system of Approved make. INSTALLATION: To comprise main runner spaced at 1200mm centers securely fixed to the structural soffit using suspension system (specifications below) at 1200mm maximum centre. The First/Last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be Armstrong wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centers. ARMSTRONG SUSPENSION SYSTEM accessories manufactured and supplied by Armstrong World Industries consisting of M6 Anchor Fasteners with hanger hole, pre Straightened Hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum pull strength of 110 kgs. (Adjustable hook clips of 0.7mm thick, galvanized spring steel can also be used for installation purpose as an additional accessory. The adjustable clip also consists of a 4 mm aquiline wire to be used with the main runner).
PLAIN PORTLAND MAPLE CEILING (WOODWORKS 600X600X18MM MICROLOOK EDGE TILES IN PLAIN WITH 15MM SUPRAFINE 43 EXPOSED GRID) SYSTEM : Providing & Fixing of Wooden finished Suspended Ceiling System with WoodWorks Microlook edge tiles with 15mm Suprafine 43 exposed grid. The Tile in Plain with approved laminate finish with 0.7mm matching PVC edge banding, would have Humidity Resistance (RH) of 70% in module size of 600x600x18mm and density of 725 Kgs/M3. The tile shall be laid on Armstrong Suprafine 43 with 15 mm wide T - section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm and a load carrying capacity of 15.5 Kgs/M2 & pull out strength of minimum 100 Kgs.. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with Suspension system of Approved make. INSTALLATION: To comprise main runner spaced at 1200mm centers securely fixed to the structural soffit using suspension system (specifications below) at 1200mm maximum centre. The First/Last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centers. SUSPENSION SYSTEM accessories manufactured and supplied by Industries consisting of M6 Anchor Fasteners with hanger hole, pre Straightened Hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum pull strength of 110 kgs. (Adjustable hook clips of 0.7mm thick, galvanized spring steel can also be used for installation purpose as an additional accessory. The adjustable clip also consists of a 4 mm aquiline wire to be used with the main runner).
FINISHING
12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)
15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 4 fine sand)
18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.
6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)
White washing with lime to give an even shade : New work (three or more coats)
Distemering with oil bound washable distemper of approved brand and manufacture to give an even shade: New work (two or more coats) over and including water thinable priming coat with cement primer.
Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer
Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm).
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
LUSTRE PAINT Providing and applying on all exposed surfaces of beams, ceiling & walls etc. 3 coats of Lustre paint of approved make and shade as per manufacturer specification with a brush or roller after levelling the surface to a smooth finish with the help of putties etc & having base coats of approved primer before applying three coats of paint. Rate to include additional coat of paints in any requried to get smooth and uniform finish.Rate to include scrapping & sand papering for wall, beam & ceiling surfaces. Rate quoted by the contractor shall include necessary cleaning, prperation of surface, centering, scaffolding, cleaning of paint stains, curing etc. complete. Rate Shall include application at all heights, wastage and provision of suitable platform with railing all around the scaffolding. Only pipe scafflolding is permitted. Scaffolding is mandatory for any height above 1.2 m from floor level. (included in structural glazing item ) actual area shall be measured.
SPECIAL EFFECT PAINT : Providing & Applying Special effect or textured paint of approved by Architect Painting the specified area in 3 coats of special effect paint by making the necessary surface of wall to receive the special effect paint as per direction of manufactures of approved quality, shade over one coat of primer and leveling course. Rate to include scrapping wall surfaces, applying Birla putty for proper finish, applying necessary.coat of primer to get firm surface to receive paint. Rate quoted by the contractor shall include necessary cleaning, prperation of surface, centering, scaffolding, cleaning of paint stains, curing etc. complete. Rate Shall include application at all heights, wastage and provision of suitable platform with railing all around the scaffolding. Scaffolding is mandatory for any height above 1.2 m Rate quoted by the contractor shall include necessary cleaning, prperation of surface, centering, scaffolding, cleaning of paint stains, curing etc. complete. Rate Shall include application at all heights, wastage and provision of suitable platform with railing all around the scaffolding. Only pipe scafflolding is permitted. Scaffolding is mandatory for any height above 1.2 m.
CONCRETE PROTECTIVE PAINT Providing and application of concrete protective paint, including initial coat of priming coat by spray or brush by diluting with water in ratio as specified by manufacturer, followed by two neat coats of finishing without any dilution. Application shall be as reccomended by Manufacturer. Dry Film thickness of one priming coat and two finishing coats shall be 225-250 microns. The datasheet of the concrete protective paint shall be submitted and approved by architect/ HPCL before begining of work. Concrete protective paint of approved make on all ceilings/ RCC extension of approved shade including supply of all materials tools as per direction of engineer in charge. Rate quoted by the contractor shall include necessary centering, provision of suitable platform with railing all around the scaffolding, cleaning of paint stains, curing etc. complete. Rate Shall include application at all heights, wastage and scaffolding.
ROLLER BLINDS: Providing & fixing of Roller Blinds make of Vista Eco translucent /Eco Blackout/ Sun screen classic Aerolux Non Blackout/ Vyoma Non Blackout, Blind Shade, Color Decided as per site Color matching to be decided by site engineer-in-charge.
PROVIDING WPM310 (Shelter guard): Single Component, flexible, waterproofing and decorative coating. which is UV stable flexible, premixed liquid applied waterproofing membrane. It has been specifically formulated as a general purpose membrane for exposed wall.Membrane shall confirm to : Membrane shall confirm to: Characteristics of liquid Form & colour: Viscous Liquid in standard Colours. Special colours on request at a premium: Specific gravity: Approx. 1.3 g/cm3; Characteristics of cured membrane - Water Vapour Transmission (ASTM E96)at 1.0 mm: 21.9 g/Sqm/24hrs; Tensile strength: AS 1145 - after 28 days dry: 2.1 Mpa, after 14 days UV exposure: 3.0 Mpa, after 2500 Hrs QUV: 5.9 MPa; Elongation at break AS 1145 - after 28 days dry: 460 %, after 14 days UV exposure: 315 %, after 2,500 Hrs QUV: 180 %; Overcoat time: 4 hrs @ 23 Deg C 50 % RH; Dry through (2nd coat): 24 hrs @ 23 Deg C 50% RH; Application temperature: 10 Deg C to 35 Deg C; Service temperature: 0 to 60 Deg C; VOC Content: 100g/L.
DISMANTLING & DEMOLISHING
Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.
Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineerin-charge.
ROAD WORK
SUB BASE Preparation and consolidation of sub-grade power road roller of 8-12 tonne capacity after excavating earth to an average of 22.5 cm depth,dressing to camber and consolidating with road roller including making good the undulations etc. and rerolling the subgrade and disposal of surplus earth with lead upto 50 meters
KERBS CHANNEL Providing , laying and making kerb channel 30 cm wide and 50 mm thick with cement conc. 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand , including finishing the top smooth etc.complete & as per direction of Engineer-in-charge.
Providing and laying 60mm thick factory made paver block of M-30 grade made by block making paver block of M-30 grade made by block making machine with strong vibratory compaction of approved size,design and shape,laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand,fillingthe joints with fine sand etc.all complete as per direction of Engineer-in-charge.
Providing and laying C.C. pavemanent of mix M-25 with ready mixed conc. from batching plant.The ready mixed conc. Shall be laid and finished with screed board vibrator,vaccum dewatering process and finally finished by floating,brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge.(The panel shuttering work shall be paid for seprately.) (Note : Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/recoverable separately)
Construction of granular sub- base by providing close graded Material conforming to specification , mixing in a mechanical mix plant at OMC ,carriage of mix material by tippers to work site , for leads and lifts,spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density,complete as per specification and direction of Engineer-in -charge With material conforming to GRADE-II(size range 53mm to 0.075mm) having CBR Value-25.
SANITARY INSTALLATIONS
KITCHEN SINKS Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm.
MIRRORS OF TOILET Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
Supply, installation, testing and commisioning of PP mineral filled low noise pipes and fittings,with push fit rubber ring sockets pipes and fittings of confirming to EN12056,with density 1.9gm/cm3 . Piping is to be suspended from ceiling level & fixed on ceiling with necessary cutting to the required length including short pieces assorted fittings such as Bend -Plain or with door/Swept Tee with or without door, 45° bends, collers, cowls etc. should have B1 fire classification according to EN4102 and is hot water resistant up to 95⁰C for short term loading & 90⁰C long term loading and has chemical resitance of pH 2-12 and completly provides sound protection and giving water tightness test for all the piping (refer technical specifications for additional details.) The rate shall include chasing of walls, laying of pipes as per standard working procedures. All the internal drainage pipes are to be suspended below the ceiling level and the pipes are to be supported by modular clamps. The rate includes the cost of all types of clamping and no other separate rate shall be given. The supports required for the Pipes should be made up of cold rolled steel of quality DX51 or greater with minimum GSM of 275 or greater and should have universal mounting slot on the front of the rail for accurate positioning of fasteners and system compatible round and long holes on back of the rail the pipe. The pipe clamps should be either split type with EPDM inner rubber lining or should be MSS-SP manufactured with FM approval and UL listing. Threaded rods should be of 4.8 strength class or greater and necessary accessories such as Hexagonal Nuts and Bolts should be of 8.8 strength class.
DN 110 mm o/d PP mineral filled SWR pipe (To be used for connection of Wc Soil Stack Vertical Stacks)
DN 75 mm o/d PP mineral filled SWR pipe
DN 50 mm o/d PP mineral filled SWR pipe (To be used for connection of Floor Drain to Trap)
Supplying and fixing approved make UPVC multi inlet floor trap with 75mm dia outlet and C.P. cover on top etc., complete with cement concrete support alround the floor trap.
European Water closet Providing and fixing approved make collection, white wall hung glazed EWC soft seat Cover of reputed brands as approved by Architect / Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing approved make collection wall hung glazed 100 % Rimless EWC soft seat Cover of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing Conceal Single piece concealed cistern of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing Control plate of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing health faucet brass with double lock 1m brass plated flexible hose and wall hook of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing 2 way bib cock with wall flange and flow restricator of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing concealed brass body of stop cock for 15mm pipeline of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing exposed part kit of concealed stop cock with fitting sleeves , operating lever and adjustable wall flange of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing C.P. toilet paper holder of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good ethe walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing Concealed brass body of Hi-Flow single lever Concealed mixer and divertor for bath and shower system with divertor assemble and cartridge sleeve of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing Single lever Exposed Part kit of HI-flow Divertor consisting of operating lever, knob and wall flange of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing Element bath spout with wall flange of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing Shower arm round heavy casted 450mm Long with 90 degree bend suuitable and wall flange of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing Overhead shower 120mm round shape single flow(ABS body chrome plated) of reputed brands as approved by Architect/ Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects as per drawings & instructions from Project- in-charge/Architect.
Providing and fixing Towel shelf with lower hanger of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing shower basket ,stainless steel,silver 51cm ,hanging shower caddy,chromium plated , 54x25.3x10.9 cm of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing of electric Water heater (25 ltrs.) of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing of Bib cock self closing pressmatic wall mounted basin tap with wall flange and flow restrictor of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing of Rubbic, italian collection table top wash basin 48x37.5x140mm of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing of Waste coupling full thread 32 mm of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing of bottle trap 32mm with 300mm Long wall connection pipe and wall flange of reputed brands as approved by Architect /Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing of Single towel rail of reputed brands as approved by Architect/ Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing of pure stainless steel push button 1000 ml liquid soap dispensor of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing of Aquisense sensor concealed type flushing valve for urinal of reputed brands as approved by Architect/ Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing of Dyna , Hindware itallian collection urinal of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
MIST ROOM FRESHNER Providing and fixing of Room freshner of reputed brands as approved by Architect/ Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
SINK TAP: Providing and fixing of sink mixer swivel spout wall mounted of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing of stainless steel grating frame of 18 gauge thick with circular perforation of 'approved pattern over CI 'traps. The grating size shall be 125 mm dia '(as directed) and shall 'be set in cement, sand mortar 1:5 reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing of SS Grab bar 600mm long of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
WATER SUPPLY
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.
20 mm nominal dia Pipes.
32 mm nominal dia Pipes
40 mm nominal dia Pipes
50 mm nominal dia Pipes
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.
20 mm nominal dia Pipes
25mm nominal dia Pipes
32 mm nominal dia Pipes
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.: 50 mm nominal dia Pipes
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore
Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :
20 mm nominal bore
25 mm nominal bore
32 mm nominal bore
Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve,with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design, with common burnt clay F.P.S.(non modular) bricks of class designation 7.5
Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 : 100 mm dia Ductile Iron Class K-7 pipes
Providing, Stringing out, cutting, Jointing and testing of ISI Marked D.I. Pipe (S&S) as per IS 8329 and laying the same in trenches to correct alignment and gradients, jointed with rubber tyton joints fitted complete including all cartage. 80mm i/d pipe lines laid complete
Providing and fixing of 50mm brass ball valve pn 25 of reputed brands as approved by Architect /Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects.
Providing and fixing 100mmx50mm PVC saddle clamp threaded suitable for installation on the distribution pipe for tapping of water connection to individual buildings complete in all respects.
Providing & fixing 100 mm i/d sluice valves flanged C.I/D.I Flanged end, stem of SS (AIS 1410) and Bronze (gunmetal) working parts Sluice Valves ISI marked 148462000, including jointing , testing & cost of Nut, Bolt & insertion sheet, all carriage complete (with the approval of Engineer in-charge).
Supply, installation, testing and commissioning of a set of hydro-pneumatic horizontal inline water transfer pump set, skid mounted with PLC panel , for domestic water with single floating VFD suitable for automatic operation and delivering the specified discharge at the specified head. Each Pump shall be of Cast Iron casing in along with NRV & ball/butterfly valves at suction & delivery line, impeller and shaft in SS 304 and shaft and sleeve with mechanical seal capable of delivering suitable capacity and connected by a flexible coupling to a totally enclosed fan cooled (TEFC) induction motor as per IEC standard.Th motor should be IE3. The set shall be complete with all the required valves , NRV’s on suction and discharge, complete with GI suction and delivery header piping of suitable size. The motor shall be suitable for 415 ± 10% volts, 3 phase, 50 Hz A.C. power supply. The set shall include an automatic control panel and presssure tank of capacity 200 ltrs. with common base frame and complete connecting accessories. The set shall be completely equipped with floating variable frequency drive for automatic operation as per load requirements and will run alternately in sequence in cascade mode based on water demand. The pump set includes pressure switch along with dry running preventer. No. of pumps - 2 working + 1 standby Head - 65 mtrs Flow - 330 LPM
Providing & fixing 100 mm i/d sluice valves flanged C.I/D.I Flanged end, stem of SS (AIS 1410) and Bronze (gunmetal) working parts Sluice Valves ISI marked 148462000, including jointing , testing & cost of Nut, Bolt & insertion sheet, all carriage complete (with the approval of Engineer in-charge).
Providing and fixing 25x600x6mm pipe , puddle 200x200x6mm , both side MS puddle flanged , 600mm long puddle flanges fabricated out of 6mm thick M.S. plates along with flanges of suitable size properly fixed in walls and top slabs of overhead tanks.
25mm dia
32mm dia
50mm dia
80mm dia
100mm dia
Providing & fixing MS vent pipe 100 MM dia C.C.I. (spun) socketed soil, waste and vent pipe 1.80 metres long: 100 mm dia. complete with 2 Nos. bends & painting with enamel paint all complete. (For OHT )
Providing & fixing ManHole Cover of size 560mm dia of reputed brands as approved by Architect/Engineer-in-charge . Rate shall be inclusive of cutting, grooving making good the walls, men material and lift up to G+6 story building, installed complete. Item to be completed in all respects. 560mm dia
Providing & fixing of 20 & 32mm dia Pipe Clamps
Providing & fixing of 40 & 50mm dia Pipe Clamps
DRAINAGE
Providing and fixing square-mouth uPVC gully trap complete with grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 180x100 mm size P type, with common burnt clay F.P.S. (non modular) bricks of class designation 7.5.
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :
450 mm dia. R.C.C. pipe
600 mm dia. R.C.C. pipe
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and makingchannels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :
Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.
Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.
Extra for depth for manholes :
Size 90x80 cm: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Size 120x90 cm: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having the bend test and chemical resistance test as per specifications and having the bend test and chemical resistance test as per specifications and having 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.
Constructing brick masonry road gully chamber 50x45x60 cm with bricksin cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.
Extra for depth beyond 45 cm of brick masonry chamber: For 500x700 mm size. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.
Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. 450 mm dia RCC pipes. metre
Providing and laying of tibba sand 100mm thick all around the uPVC sewer pipe for cushioning before refilling the trench with soil to protect it against damages during re-filling.
Supply, installation, testing and commissioning of a set of hydro-pneumatic horizontal inline water transfer pump set, skid mounted with PLC panel , for domestic water with single floating VFD suitable for automatic operation and delivering the specified discharge at the specified head. Each Pump shall be of Cast Iron casing in along with NRV & ball/ butterfly valves at suction & delivery line, impeller and shaft in SS 304 and shaft and sleeve with mechanical seal capable of delivering suitable capacity and connected by a flexible coupling to a totally enclosed fan cooled (TEFC) induction motor as per IEC standard.Th motor should be IE3. The set shall be complete with all the required valves , NRV’s on suction and discharge, complete with GI suction and delivery header piping of suitable size. The motor shall be suitable for 415 ± 10% volts, 3 phase, 50 Hz A.C. power supply. The set shall include an automatic control panel and presssure tank of capacity 200 ltrs. with common base frame and complete connecting accessories. The set shall be completely equipped with floating variable frequency drive for automatic operation as per load requirements and will run alternately in sequence in cascade mode based on water demand. The pump set includes pressure switch along with dry running preventer. No. of pumps - 2 working + 1 standby Head - 65 mtrs Flow - 200LPM
Providing, laying in trenches to correct gradient and alignment and jointing of UPVC Foam core pipes confirming ISI specification IS : 16098 (Part-1) : 2013 class- SN-4 & SN-8, laying the same in trenches to correct alignment and gradients, cutting and jointing, testing for water tightness and making good the leakages and defects including cost of specials (Specials and Solvent should be of same make as that of pipes) complete in all respects.
160 mm o/d pipes : SN-8
200 mm o/d pipes : SN-8
110 mm o/d pipes : SN-8
PILE WORK
Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tubewell boring machine shall not be used .
450 mm dia piles
600 mm dia piles
Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing. Note: 2. Testing agency shall submitt the design of loading platform for the approval of Engineer-in-charge. Single pile above 50 tonne and upto 100 tonne Safe capacity.:
Initial test (Test Load 2.5 times the Safe capacity)
Routine test (Test Load 1.5 times the Safe capacity)
WATER PROOFING
Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.)
Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations : a) Applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks /brick bats 25 mm to 115 size wiht 50 % of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer -in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of juncitons of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.
Providing and applying integral crystalline dry shake of hydrophilic in nature for waterproofing treatment to the RCC structures like basement raft, foundation slab, sewage & water treatment plant slab, warehouses floor, parking structures and water tank base slab etc. sprinkled @ 0.60kg per sqm or higher as recommended by the manufacturer's specification over the lean concrete of above cited structures. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 85%, compared control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline dry-shake shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-incharge. The product performance shall carry guarantee for 10 years against ny leakage.
STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL
Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.
Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the the building for all heights and all levels , including : (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry / structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge. Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places. Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or by any other accreditation body which operates in accordance with ISO / IEC 17011 and accredits labs as per ISO/ IEC 17025. 1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr 2. Static Water Penetration Test. (50pa to 1500p) as per ASTME- 331-09 testing method for a range up to 2000 ml. 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm. 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4- 09 testing method for Qualitative test, Tests to be conducted on site. 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml.
Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.11.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.
ALUMINIUM COMPOSITE PANEL (ACP)(4 MM THICKNESS) Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF/ Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.
OPENABLE PANEL Extra for openable side/top hung vision glass pannel (IGU) including providing and supplying at site all accessories and hardware for the openable pannel as specifide and of the approved make such as heavy duty stainless steel friction hinges min 4-point cremone locking sets with stainless steel plates , handles buffers etc. including necessary stainless steel screws /fstners nuts.bolts washers etc. all complete as per architecture drawings as per the approved shop drawings , as specified and as directed by the engineer in charge.
(B). INTERNAL & EXTERNAL ELECTRICAL ESTIMATE
INTERNAL ELECTRICAL ESTIMATE
Internal Wiring
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B
Wiring for circuit/ submain/Light Plug/ Power Plug wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 X 1.5 Sq mm + 1 X 1.5 Sq mm earth wire (for LP & SB) (40 x 4.5 x 63) x1 = 11340)
2 X 2.5 Sq mm + 1 X 2.5 Sq mm earth wire (for PP) (40 x 4.5 x 9) x1 = 1620
2 X 4 Sq mm + 1 X 4 Sq mm earth wire (for AC) (40 x 8.5 x 3) x 1 = 1020
Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. (PP for AC157+ PP190=347X15=8655)
TELEPHONE, TV POINTS
Supplying and drawing following pair 0.5 mm dia FRLS PVCinsulated annealed copper conductor, unarmored telephonecable in the existing surface / recessed steel / PVC conduit as required. 2 Pair ( 80Tel points 80X15=1200)
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.(40x15=600)
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm (for telephone / TV cable/Lan cable) 1200+210+3200=4610
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
5/6 A switch
15/16 A switch
3 pin 5/6 A socket outlet
Telephone socket outlet
TV antenna socket outlet
Bell push
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box ncluding connections but excluding modular plate etc. as required.
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required
Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75 mmX75 mm) for TV/Tel points
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required.
Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.
Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.
Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep
Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.
Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B
SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB/ RCBO/ RCCB's: Supplying and fixing following way, horizontal type three poleand neutral, sheet steel, MCB distribution board, 415 V, onsurface/ recess, complete with tinned copper bus bar, neutralbus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) Approved Make- Schneider (Acti-9), L&T (AU Series), Hager.
4 way (4 + 12), Double door
6 way (4 + 18), Double door
8 way (4 + 24), Double door
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole
Double pole
Triple pole
Triple pole and neutral
Supplying and fixing following rating, four pole, (three phase and neutral), 415 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A
Internal Lighting Fixtures
Supply of Heavy Duty Metallic ventilating exhaust fan 300 mm sweep 900 RPM, complete with blade etc.
Supply of Louver shutter size 300mm complete in all respect
Supply of Ceiling fan double ball bearing complete with petty material , conopy for errecction as per satisfaction of Engineer in-Charge, approved brand as approved by engineer in-Chare white in colour without fan regulator: Ceiling fan 48" (1200mm)
Supply and erection of wipro/phillips make cat no. CRCO10R038HP57SLAB Recess mounted LED luminaire 2'x2' square light with minimalist trim and full diffuser. Immaculate led light of approved make.
Supply,installing testing and commsssioning of wipro/ phillips make 2x2' verge led light cat no. LM29-451-XXX-57-XX High efficiency recess mounted versatile LED luminaire
Supply,installing testing and commsssioning of Trunk liena 4feet (31091) tubelight of approved make.
Supply,installing testing and commsssioning of approved make Cob Deep Resseced 7wt light .
Supply,installing testing and commsssioning of approved make 6 W LED downlighter . Recessed mounted round slim panel LED downlighter
Supply,installing testing and commsssioning of pendent hanging ceiling lamp.
Supply,installing testing and commsssioning of Led recessed linear light fitting (1200mm length) for making continous linear arrangement including cascading kit etc with aluminium extrusion housing CCT 4000k with system lumen output better than 3200 lumens and system efficacy better than 115 Lumens/watts,driver efficiency better than 85%,PF better than 0.95 CRI better than 80 percent Service Life 50000 Hr@ L70, UGR<19.
Supply,installing testing and commsssioning of 15W Spheris LED - circular LED Downlighter
Supply,installing testing and commsssioning of Surface light 12wt (59152)
XLPE/ PVC INSULATED ARMOURED CABLES Supply & laying of aluminium conductor XLPE/ P.V.C. insulated PVC sheathed armoured and served cable to be laid1 m below ground level including excavation, sand cushioning, covering with sand & bricks and back filling the trench etc., of the required size :
Aluminium conductor XLPE/ PVC insulated PVC sheathed armoured and served cable working voltage 1100volts grade 300sq.mm (3 ½ Core)
Aluminium conductor XLPE/ PVC insulated PVC sheathed armoured and served cable working voltage 1100volts grade 185sq.mm (3 ½ Core)
Aluminium conductor XLPE/ PVC insulated PVC sheathed armoured and served cable working voltage 1100volts grade 50sq.mm (3 ½ Core)
Aluminium conductor XLPE/ PVC insulated PVC sheathed armoured and served cable working voltage 1100volts grade 16sq.mm (4 Core)
XLPE/ PVC INSULATED ARMOURED CABLES (LOOSE): Supply & laying of aluminium conductor XLPE/ P.V.C. insulated armoured and served cable to be laid loose in the existing trench or pipe as per PWD General Specifications 2010:-
Aluminium conductor XLPE/ PVC insulated PVC sheathed armoured and served cable working voltage 1100volts grade 185sq.mm (3 ½ Core)
Aluminium conductor XLPE/ PVC insulated PVC sheathed armoured and served cable working voltage 1100volts grade 150sq.mm (3 ½ Core)
Aluminium conductor XLPE/ PVC insulated PVC sheathed armoured and served cable working voltage 1100volts grade 120sq.mm (3 ½ Core)
Aluminium conductor XLPE/ PVC insulated PVC sheathed armoured and served cable working voltage 1100volts grade 70sq.mm (3 ½ Core)
Aluminium conductor XLPE/ PVC insulated PVC sheathed armoured and served cable working voltage 1100volts grade 35sq.mm (3 ½ Core)
ELECTRICAL NS ITEMS: Supply, Carriage and laying of Power Copper Cables, Solid Copper Conductor Upto 6 Sqmm And Balance Stranded Copper, XLPE Insulated, Cores Laid Up, PVC Innersheathed, Unarmoured, Extruded PVC Type ST2 Sheathed, 650/1100 V Grade As Per IS 7098 (Part 1) 1988. The cable is to be laid in existing trench / pipe / duct fixed with suitable clamps as per site requirements including their cost. The work should be completed as per satisfaction of Engineer-in-charge / Architect.
4Sqmm 3Core
16Sqmm 4Core
25Sqmm 4Core
35Sqmm 4Core
Supply and erection of modular type 25A Switch with indicator and 2Nos. 25A Sockets (for incoming and outgoing supply for stabiliser) on existing modular sheet (Legrand (Arteor) / North-west /Crabtree / MK make) with making connection including cost of copper wire. Supply, fabrication and carriage of cubical type panel compartmentalized fabricated out of 16G CRCA sheet complete with erection of incoming and outgoing switchgear, supply and erection of busbars meters, indicators, cable end boxes as required. The panel shall be wall mounted as per drawing and site. The panel shall be totally enclosed dust and vermin proof construction with square sections rubber gaskets. The wall mounted panels shall be strictly as per specifications. The busbar will be wrought aluminium E91E grade suitable for 50KA fault level for one second (The fabricator will have to give manufacturer's certificate of E91E grade wrought aluminium busbar). All four busbars should be insulated with colour should PVC heat shrinkable sleeves. The panel should be complete as per the drawing and includes all internal wiring with PVC copper cable of requisite size complete with name plates of each feeder, danger plate, solid bus connections, cable alleys, busbar chamber etc. and other petty material The panel will be powder coated after chemical treatment. The degree of protection panel should be IP54 and should be extendable on both sides. All MCCBs are to be provided with extended rotary handles and spreaders for proper termination of cables. All MCBs are to be 'C' series .
Supply, Erection of RJ-45 computer Jack for CAT-6 cable
ABSTRACT OF COST - ELECTRICAL INSTALLATION WORKS FOR 125KVA DG SET
DG Set- SOUND PROOF DG SETS OF 125 KVA
"Supply ,installation ,testing and commissioning of 125 KVA water cooled silent DG set comprising of water cooled Diesel Engine developing 156 BHP @ 1500 RPM & 125 KVA alternator rated at three Phase , 415 Volts , 50 Hz: 0.8 P.F. @ 1500 RPM Both mounted , and alighed on a common MS base Frame Complete with MS Fuel tank , Standard AMF Control Panel , Residential Exhaust Silencer , AVM Pads fitted on base frame , 1 nos. 12 Volts DC Battery ,Battery Leads , 1st fill of lube oil all housed in sound proof Acoustic Enclousre as per specification attached as per satisfaction of engineer in-charge Note : The Agency Will provide first filling of full tank Diesel with supply of DG set" DG AMF PANEL supply, installation ,testing and commisioning of DG , cubical type,totally enclosed ,free standing type ,dust ,damp and vermin proof made up of 14/16 SWG CRCA sheet ,complete with busbars, M.V . Danger notice plate,inter connections with suitable capacities aluminium leads / solid aluminium strips / rods ,power coats painted and having incoming and outgoing switchgear as mentioned below and complte as required . 1. All relays to operate at 240 V single phase , 50HZ , AC supply through UPS 2. Panel should be suitable for mannul and autommatic operation (AMF) and shall be complete as required . one no.250 A auto change over switch for changeover state electricity board power and DG set power incuding by pass facility as approved by the engineer - incharge. 1 no. MCCB as per following details specifiations 250 AMP. 415 V , 4 pole MCCB with Microprocessor realse and variable current settings 0.8 to 1.0 ) with earth fault realese "ON" LED indicating Lamp and 2A control SP MCB Extended rotary operating mechanisum digital energy meter with one set of suitable CTs, CT storting link Digital Ampere Metre of suitable range with suitable set of CTs and ASS Digital Volt meter with VSS and HRC fuse Digital multi function meter to show ,KWH ,KVAH ,P.P and frequency meter one set of suitable CTs , CT shorting links. PROTECTION AND AMF COMPONENTS FOR ABOVE MENTION DG SET Over voltage relay , under voltage relay, Battery charger (with trickle and boost charging)., Digital voltmeter and ammeter., 8 window Alarm annuciator with separate hooter , accept ,reset and push button, Hooter Engine cranking relay main supply voltage monitor ,alternator voltmeter monitor and engine starting releys Auxillary relays,Timer ,Push button and control fuses Phase sequence relays ENCLOSURE: Fabrication, PVC sleeving ,Control/power wiring and necessary electrical / mechanical interlocking etc. any other item required for proper functioning of the system complete as required Providing and fixing oil tank of suitable capacity complete with suitable M.S Fabricated ,M.S stand oil leve;l indicator gauge tank and stand duly painted complete with float switches etc. including its connetions to the fuel tank of the DG set complete as required The silencer should be minimum 20'-0" long nothing extra shall be paid 125KVA DG set with AMF panel mentined as above Model No:6BTAA5.9G13
Earthing of DG Set.
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.( 2No for DG body earthing)
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.(2No. For DG Neutral earthing)
Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.
CONCRETE WORK FOR DG SET FOUNDATIONS
Providing & laying in position cement concrete 1:3:6 ( 1Cement:2Coarse sand :6 graded stone aggregate 20mm nominal size) in foundation of DG sets etc including form work etc as required. (1No DG set+1No CSS 2X6x5X.6Mtr)
SCHEDULE NO. 3 - (11KV SUB STATION ETC)
Providing and fixing of FIRE EXTINGUISHER ABC Powder type (stored pressure )as per is :15683 complete with all accesories as per manufactures specification.ISI Mark complete in all respect. 4 kg capacity.
Providing and fixing of FIRE EXTINGUISHER CO2 type as per is :15683 complete with all accesories as per manufactures specification.ISI Mark complete in all respect. 4.5 kg capacity
PCC POLES Supply and erection of pre-stressed cement concreete pole of suitable length with a given planting depth confirming to IS1678-1978 below ground level in excavated pit of suitable dimensions complete in all respect as per satisfaction of engineer in charge. PCC pole overall length 11metre planting depth 1.83 metre, top dimensions 152.4mmx 203.2mm bottem dimensions 152.4mmx368.3mm load capacity 363Kg and wt 1146Kg.ACSR- Supply and sagging of al conductor steel reinforced (ACSR) on pole including binding with insulators.
GO SWITCH 200A & POLE ACCESSORIES Supply & erection of 11KV 400-800A GO switch confirming to ISI specifications. The item includes supply and erection of operating pipe and handle arrangement of MS flate 50mmX6mm and chennels 75mmx40mm sheet. The GO switch is to be fitted with locking arrangement so as it locks upward on"ON" position and locks downward in "OFF" position. The entire GO switch assembly/unit should be properly earthed and the job is to be completed as approved by engineer-in-charge.
ACSR DOG conductor (100sq mm) Size (6/4.5Al+1/4.5GI)
Supply and Erection of MS angle iron size 50mm x 50mm x 6mm thick with cutting, bending and necessary holes as desired by Engineer-in-charge at site.
Supply and erection of MS chennel iron size 100mmx50mmx6mm thick with cutting,bending and necessary holes as desired by engineer in charge
Supply and erection of MS flat size 50mmx5mm thick with cutting,bending and necessary holes as desired by engineer in charge
XLPE INSULATED HT ARMOURED CABLES
Supply & laying of Circular Aluminium conductor, conductor screened with extruded semiconducting compound, XLPE insulated, insulation screened with extruded semiconducting combination in combination with copper tape (0.3KA for 1sec.) cores laid up, FRLS PVC inner sheathed, galvanised steel strip armoured and overall FRLS PVC sheathed cable confirming to IS:7098/II/85 working voltage 11KV(UE) grade to be laid 1 m below ground level including excavation, sand cushioning, covering with sand & bricks and back filling the trench etc., of the required size:- Circular Aluminium conductor, conductor screened with extruded semiconducting compound, XLPE insulated, insulation screened with extruded semiconducting combination in combination with copper tape (0.3KA for 1sec.) cores laid up, FRLS PVC inner sheathed, galvanised steel strip armoured and overall FRLS PVC sheathed cable confirming to IS:7098/II/85 working voltage 11KV(UE) grade 70sq.mm (Three Core)
Earthing of Sub- Station.
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.( 2No for Transformer body earthing)
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. ( Neutral Earthing)
Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.
Supply and making outdoor cable termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for 3X70Sq mm XLPE A conductor cable of 11 KV grade as required.
Supply & Erection of galvanised D iron clamps complete with shakle insulator (100mmx110mm) GI bolts, Nuts and washers, coach screws etc as required.
Supply & erection of 75 mm x 90 mm shackle insulators with G I bolt, nuts and straps etc. as required.
Supply & erection of galvanised stay sets for 11KV over head lines complete with 19/20mm dia 1.8mtr long GI stay rod , anchor plate of size 45cmx45cmx7.7mm thick, thimbles, stay clamps, turn buckle) 20mmx600mm), 7/4,00 mm dia GI Stay wire and 11 KV strain insulator etc in cement concreat 1:3:6 ( 1 cement: 3 Coarse sand : 6 graded stone aggregate 40mm nominal size) foundation including excavation and backfilling as required.
Supply & erection of 11KV pin insulators with GI pin confirming to ISI specifications. The item includes supply and erection of nuts and bolts and other accessories whatsoever required at site for fixing it to the structure pole. .The job is to be completed as approved by engineer incharge.
Supply & erection of 11KV Disc insulators with GI pin confirming to ISI specifications. The item includes supply and erection of nuts and bolts and other accessories whatsoever required at site for fixing it to the structure pole. .The job is to be completed as approved by engineer incharge.
Supply & erection of 11KV Lightning Arrestors suitable for 3 wire , 11KV overhead lines with rated voltage 9KV(rms) with nominal discharge current rating 5KA and complete with galvanised clamping arrangement G.I. bolts nuts washers etc etc as required confirming to ISI specifications. .A seprate earth to be provided to Lightning arrestor complete as approved by engineer incharge.
Supply & Erection of 11KV / 110V, 30/5A CT/PT Pole mounting type for Metering duly approved by HSEB.
Supply & Erection of 11KV / 110V 630KVA, 11kV Outdoor Package Sub-Station consisting of following , Approved Makes- Schneider, ABB, Siemens HT Switchgear:- MV COMPARTMENT 11 KV, 630A, 25KA/1Sec indoor type non-extensible, SF6 gas insulated Ring Main unit with sealed pressure system criterion in accordance with the IEC: 60298,62271 - 202.IAC of 20 kA for 1 s for tank and cable box category IAC-AFL . The indoor non -extensible SF6 insulated RMU consist of 2 No. incomer Isolator and 1 no. outgoing Vacuum Breakers with self powered relay for protection of transformer . Rated for Voltage 12kV, 400A, 25 KA for 1 sec. The Switchgear includes the following HV cubicles with series trip,self powered microprocessor based Over current & Earth Fault ( IDMTL + Inst.) relay x 95.sq.mm Al. unarmoured XLPE (E) Cable., protection,Interconnection between HT and Transformer shall be using 1C x 3 Transformer:- 630 KVA,11KV/433V,DYn11, ONAN OIL Type, hermetcially sealed Copper wound transformer with corrugated wall design & top bushings for HT & LT with off load tap Changer of rating+5 to -5% @2.5% on HT side of transformer. Magnetic Core: Prime grade of M4 or better. H.V. Impulse withstand voltage (KV peak): 75 kVp.Transformers shall be designed for 110% continuous overfluxing withstand capability. The Losses of Transformer should be as per IS 1180 part 1 Eff level 2 norms LT PANEL:- LT Indoor panel 433 V air insulated Aluminium busbar having capacity 1000A, 50Hz,50KA withstand fault level capacity, MFM - EM6400NG in incomer . Fabrication using 1.5/2 MM CRCA sheet steel , Ingress protection IP4X , complete with internal wiring. INCOMER cum OUTGOING :- Incomer - 4 Pole, 1000A, Microporcessor based , Drawout type ACB with O/C, S/C & earthfault release. The fault system of 50kA, Ics=Icu=Icw for 1 sec. Suitable for Isolation as per IEC 60947-2. ACB should have LCD Display (Voltage & Current) with %age loading graph of each phase on release. Tripping time < 30 msec. Outgoing- 4 no MCCBs 250A FP and 2 no MCCB 125 A FP with thermal magnetic release with double break mechanism. APFC Panel- Incomer 1 no MCCB TP Pole 315A Ics= 50kA Thermal magnetic with Double break roto mechanism. Intelligent APFC Relay with 200 kVAr MPP Heavy duty Capacitor with suitable rating of contactors & Short ckt protection device for each banking. Banking of Capacitor should be 12.5 X2 no, 25 X 3no, 50 X 2no. Outdoor Enclosure:- Outdoor Enclosure :- The enclosure shall be made of 2.0 mm thickness Galvanized Sheet Steel tropicalised to meet Indian weather conditions including all the partition sheets & doors.The base of the enclosure shall be of 4.0 mm thickness Hot Dip Galvanized Sheet Steel to ensure rigidity for easy transport & installation. The entire Package Substation shall be Factory Assemble & Factory Fitted. The enclouser shall have IP54 degree of protection for HT & LT switchgear compatment IP34 degree of protection for Transformer compartment. The Enclosure to be tested for Internal Arc fault test to the tune of atleast 20 KA for 1 second adhering to as per latest IEC 62271-202.The temperature rise test on enclosure for K10class.The enclosure exterior shall be powder courted.The compartment illumination lamp with door operated switch shall be provided for MV & LV comparatment. Interconnection & Earthing:- Interconnection Between HT switchgear & Transformer using 1Cx3x95Sq.mm XLPE Single core cable & Interconnection between Transformer & LT switchgear using Busbars. Internal earthing connections by GI strips. HT switchgear/Transformer/LT switchgear, MFM, must be of same make:- Packge Sub-Station is outdoor plinth mounted type. Civil work for package substation is not in our scope. The Foundation details will be furnished. Package Sub-staion will be complete with the internal interconnections & earthing. Accessories required for the external connections of HT & LT cables like termination kits , lugs , glands etc & extending of earth bar to earth pits is not included in our scope.
SCHEDULE NO.2 - FANS & FITTINGS& OTHERS
SUB STATION LIGHTING
SITC 20W LED 1200mm Batten Light. The Astra Fixture is a surface & wall mounted LED batten with extruded aluminium housing and robust construction . PF>.95, System Wattage LED 20W with Minium 1500 lumens in 5700k.
Supply of energy efficeint AC ceiling fan with 5star rating complete in all respect of approved quality by the Engineer on charge of work. Ceiling Fan 48"
S/E of heavy duty industrial type of Exhaust fan 900 RPM including the cost of making hole in the wall or providing and fixing MS Sheet 14 SWG with painting as per satisfaction of engineer-in charge. (Commercial / industrial model only). Size 300mm sweep, 900 RPM
Supply of louver shutter size 300 mm complete in all respect
SITC Surface Mounted wall light Light. The Fixture should be Made of chrome&metal Housing.PF>.95, System Wattage Tronto E27,24Ww with Minium 1500 lumens in 5700k.
SITC of LED Surface mounted round/square type downlighter. The Fixture should be Made of Extruded Aluminium Housing. Inbuilt Protection of 2kv, PF>.95, System Wattage 15W integral housing for driver. Minium 100 lumens/W in 5700k.
STREET LIGHTING/AREA LIGHTING
SITC 45W LED Street Light. The Fixture should be Made of pressure diecast housing with TOUGHNED GLASS diffuser and indivisual LEDs with secondary optics with IP 66 protection. PF>.95, System Wattage LED 45W with Minium 1500 lumens in 5700k.
SITC Focuslight/Post Light/Bollard Light/ Gate Light. The Fixture should be Made of Dark grey & Glass, Cast Al Metal Spigot Housing with decorative clear opal acrylic diffuser with IP 65 protection. PF>.95, System Wattage LED 40W with Minium 1500 lumens in 5700k.
FIDDER PILLER BOX Supplying , Installation, testing and commissioning of front and back openable, double door outdoor feeder pillar not less than 800 mm x 500mm x 300 mm depth fabricated out of M.S. sheet of thickness not less than 2 mm having inside door with cut out for operating accessories mounted after opening front and slanting top suitably over hang on all sides, ventilator louvers with wire mesh, earthing bus & stud base mounting angle frame of size 45 mm x 45 mm x 5 mm thick, and concrete / brick foundation cable entry knock out, locking arrangement, rubber gasket suitable for providing & fixing the following switch gear and accessories and 100 Amp TPN aluminium . Busbar, including connection etc. as required A) Incomer : - i) 60-100 AMP, 4 pole, 35 KA, MCCB i/c Rotary Handle( Similar to M/s Schneider- Easypact CVS) - 1 No. B) Outgoing :- i) 40 Amp 3P & N MCB 'C' Series - 2 Nos. ii)32A 3Pole contactors 2No Legrand LC1D40 iii) Analogue 24hrs time switch iv) Danger notice plate - 1 set v) Phase indicating lamp (R,Y,B) - 1 set vi) 2.0mm thick FP with 100Amp,4 strip Alu Bus Bar ( 0.80 x 0.50) vii) 45x45x5mm angle iron frame with CC foundation
Street Light Poles Earthing
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.
LIGHTNING ARRESTERS ON BUILDING
Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)
GALVANIZED STEEL OCTAGONAL POLES FOR WIND VELOCITY OF 160 Km/ HOUR: Supply and erection of galvanized steel octagonal pole of suitable length conforming to IS 2629/IS 2633/ IS4759. The pole shall be in single piece (single hot dip galvanized) and shall tapered towards the top.The bottom section shall have open able slot with exterior surface door & shall have suitable locking arrangement for housing three phase 4wire cable connection, bakelite sheet, MCB, loop in and out arrangement for incoming/ outgoing cables. There shall also be suitable arrangement for the purpose of earthing. Rigid Base plate of suitable size and thickness shall be welded inside and outside at the bottom of pole with provision for fixing 4 foundation bolts.The octagonal pole shall be bolted on a pre- cast foundation with a set of four foundation bolts for greater rigidity. The foundation shall be erected over cement concrete M20 of given size to fixed up to a required planting depth below ground level as required:-
a) Galvanized octagonal pole overall length 6 metre (sheet thickness 3mm), top dia.(A/F) 70mm and bottom dia. (A/F) 130mm, foundation size below ground level 550mm x 550mm x 1200mm, 4Nos. foundation bolts size 20mm dia., length≥ 600mm with base plate dimensions 220mm x 220mm x 12mm thick.
b) Supply and erection of single arm bracket 1 metre long for 4 to 6 metre long galvanized octagonal pole, the bracket should be fixed on the top of the pole having top outer dia. 70mm (A/F) complete in all respect as approved by the Engineer-in-charge at site.
SCHEDULE OF QUANTITY FOR FIRE SUPPRESSION WORK
Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft,mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 LPM AT 56 M HEAD::Jockey Pump
Supplying and fixing air vessel made of 250 mm dia, 8mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.
Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :
150 mm dia
100 mm dia
80 mm dia
50 mm dia
Providing and fixing S.S Pressure Gauge complete as required complete in all respect. : Dial diameter 150mm calibration 0-16 Kg
Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :
150 mm dia
100 mm dia
80 mm dia
Providing & fixing ISI Marked Cast Iron Dual Plate Wafer Type Check Valve flanged end class PN-1.6 as per IS with nitrile seat SS shaft & springs in pipe lines including jointing with rubber insertion, nuts, bolts and washers, matching flanges of required thickness, etc. complete in all respects.
150 mm dia
80 mm dia
Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.
For 200 mm dia
For 150 mm dia
Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. : For 100mm dia
Providing, fixing and jointing Forged Brass Ball valve screwed with SS/BRASS ball & spindle & Teflon seats, on Pipe lines including all carriages complete. : 15mm i/d Brass Ball valves
Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :150mm dia
INTERNAL & EXTERNAL FIRE HYDRANT SYSTEM
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :
80 mm dia pipe
100 mm dia pipe
150 mm dia pipe
Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. :-150 mm dia i/d
Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel
Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :Single headed Stainless steel
Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : stainless steel (Grade 304)
Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :- Gun metal
Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.: - 40 m
Supplying, Installation, Testing and Commissioning of weather proof cabinet for hose fabricated out of 1.6mm thickness M.S. sheet with front glass door having locking arrangement, suitable to accommodate all the necessary pipes, accessories, fittings etc including painting the metal portion with one coat of ready mixed primer paint and two coats of synthetic enamel paint of approved shade and quality, sign writing etc. : 900 mm wide x 600 mm high x500 mm deep size (for yard hydrant)
Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :
80 mm dia
150 mm dia
Providing and fixing fire brigade inlet connection of cast iron body with ss-304 grade 63mm dia instantaneous type male coupling with built in check valves and 150mm dia flanged outlet complete with bolts, nuts and rubber insertions as per IS:904. (to be connected to static tank). : Two Way inlet connection
Supplying, Installation, Testing and Commissioning standard Fire Man's axe with heavy insulated rubber conforming to IS 936 complete in all respect.
SPRINKLER SYSTEM
Providing, laying, fixing, testing and commissioning of 'C' Class heavy duty MS Pipe conforming to Indian Standard IS : 1239/3589 including fittings like tees, bends, sockets, elbows, flanges, tapers, nuts bolts, gaskets etc. fixing the pipe on the wall / ceiling with suitable clamps and painting with two or more coats of synthetic enamel paint of required shade complete as required.
100 mm dia
80 mm dia
65 mm dia
50 mm dia
40 mm dia
32 mm dia
25 mm dia
Providing and fixing S.S-304 grade Pressure Gauge complete as required complete in all respect. Dial dia 100 mm calibration 0-16Kg/cm2.
Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler
HAND APPLIANCES
Providing and fixing of FIRE EXTINGUISHER, ABC Powder type (stored pressure) as per IS: 15683 complete with all accessories as per Manufactures Specification. ISI Mark complete in all respect. :Capacity 6.0kg. I.S.I. Marked.
Providing and fixing of FIRE EXTINGUISHER, CO2 type as per IS: 15683 complete with all accessories as per Manufactures Specification. ISI Mark complete in all respect. : Capacity 4.5 kg. I.S.I. Marked
Providing and fixing of FIRE EXTINGUISHER,mechanical foam type (stored pressure) as per IS: 15683 complete with all accessories as per Manufactures Specification. ISI Mark complete in all respect. :Capacity 9 ltr.
ELECTRICAL WORKS
FIRE FIGHTING PUMP PANELS & EQUIPMENTS
Supply, Installation, Testing and Commissioning of 2 loop addressable fire alarm control panel, expandable upto 32 loops. Controller shall be 5.7 inch color touch screen display with stylus(320*240 pixels), inbuilt networking port(both RS485&Ethernet), TCP/IP port,Serial port for printer,two supervisory inputs,two position key switch and USB port for programming. The Panel shall handle 4096 detection points, 10,000 history events,menu driven user interface with smart search. The events shall be displayed in different colors- red for alarm events & yellow for trouble etc. for easy identification. The Panel shall be VDS/EN 54/UL approved.
Supply, Installation, Testing and Commissioning Active Repeater Panel. Controller shall be 5.7 inch color touch screen display with stylus(320*240 pixels), inbuilt networking port(both RS485&Ethernet),Serial port for printer,two supervisory inputs,two position key switch and USB port for programming. The Repeater Panel shall allow users to acknowledge, reset,silence, program, view hisory events...etc (All functions similar to main panel)The user interface of the repeater panel shall be same as the Main Controller with menu driven user interface with smart search. The events shall be displayed in different colors- red for alarm events & yellow for trouble etc. for easy identification. The Panel shall be VDS/EN 54/UL approved.
Supply, Installation, Testing and Commissioning of addressable multisensor detector with a combination of Optical and Thermal including mounting base, auto addressing feauture as required. Detetctor should have 2 inbuilt isolators as per NFPA 72 style 7 wiring requirements (one for incoming and one for outgoing line) for maintaining operational availability of all elements in the loop in the event of a short circuit and to meet style 7 requirements. High resistance to electromagnetic effects in accordance with EFSG agreement EFSG/F/97/005 .Detector should monitor Electromagnetic interference and report to the panel - current and average values. EMC safety for detector shall be 50 V/m. Shall be EN54/ VDs/UL certification..(Detectors without Inbuilt Isolators may be considered with an additional Isolator Module per detector)
Supply, Installation, Testing and Commissioning of addessable manual break glass unit (Double action) with inbuilt isolators as per NFPA 72 style 7 wiring requirements, with flexible network structures & necessary fixing arrangements with key complete as required. Shall be EN 54/Vds/UL Certification.
Supply,ssable Control Relay Module with inbuilt isolators as per NFPA 72 style 7 wiring requirements & with flexible network structures with a maximun switching current of 1A @ 30V DC. Shall be EN54/ Vds Certification/UL
SITC of Glow Type EXIT Sign Board photo luminescent of size 300 mm x 250 mm x 1.5 mm rigid sheet signage containing Zink Sulphate as bare chemical class – 1 material PSPA fixed on 3 mm acrylic sheet on both side showing marking (running man, Arrow and Exit) and hanged with the ceiling with chain and fastener including cost of labour & material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work
Supply and erection of 1.5sqmm PVC unsheathed copper conductor cable single core 1100 volts grade in pipe of suitable size excluding cost and erection of pipe .
Supply, Installation, Testing & commissioning of celling Mount Speaker with operation 6 Watts.
Supply, Installation, Testing & commissioning of 480W Booster amplifier, Battery voltage -24Vdc (max.10%deviation), Frequency response-60Hz to 15 kHz(+1/-3 db), Distortion (at rated out power ar 1 khz)- <3%, InputsXLR, Impendence-20k , Sensitivity-1V (mic inputs), S/N->80 DB.
Supply, Installation, Testing & commissioning of 3KVA UPS on line, Double conversion, Microprocessor controlled, With LCD, Input Voltage: 230V Freq : 40-70HZ P.F. :0.95 Output : 220Volt ± 2% Freq: 50HZ ± 0.05HZ, P.F.: 0.8 With SMF Batteries for 60min backup on full load.
Supply, installation, testing and commissioning of 2 core multistrand 1.5 sq mm annealed copper conductor speaker cable in existing pipe/ channel I/C connection etc.
Supply and erection of PVC pipe 25mm dia ISI marked (Medium) recessed in wall / ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect upto the entire satisfaction of Engineer-in-charge of work.
Supply, installation, testing and commissioning of 17 U Standard rack to place all equipment.
Estimate of CCTV system
Supply, installation, testing and commissioning of UL Listed IP CCTV fixed dome Varifocal Coloured Camera, with motorized focal lenz , Full HD (1920 x 1080) high resolution,1/3” Progressive scan CMOS, 0.2 lux with 3-9 mm auto/DC iris lens or equivalent high definition, motion detection,76dB wide dynamic range, H.265 / H.264 / MPEG4 / MJPEG, quad stream, Bit rate 32 Kbps-45 Kbps, 12 VDC ± 10%, PoE (802.3af), with ONVIF supported, in built HD card slot up to 128 GB, connectors complete as required in dome shape fixed type for mounting recessed in false ceiling or mounted on wall complete as required in accordance with laid specification or upto the satisfaction of engineer in charge.
Supply, installation, testing and commissioning of UL Listed IP CCTV True Day/Night Camera, 2 megapixel (1920 x 1080) high resolution, 1/3” Progressive scan CMOS, [email protected], AGC ON. 0 Lux with IR on, H.265/H.264 / MPEG4 , Quad stream, Bit rate 32 Kbps-45 Kbps, Standard IP66, PoE (802.3af), Varifocal lens ( 2.8mm - 10mm ) or equivalent high definition,IR range 50-60 mtr, motion detection, Analytics required with Licences for mentioned Analytics (Line crosing, Loitering, Tracking, Counting, Forensic search), with ONVIF Profile S supported, in built micro SD card slot up to 128 GB, connectors complete as required IR Bullet fixed type for mounting on wall or surface mounted with back box and adapter plate complete as per tender specifications required. (For Outdoor area) th laid specification or upto the satisfaction of engineer in charge.
Supply, installation, testing and commissioning of UL Listed IP PTZ Camera, 2 megapixel (1920 x 1080) high resolution, 1/3” Progressive scan CMOS, 30X Optical zoom, 12X digital Zoom,, H.265/H.264 / MPEG4 , Quad stream, Bit rate 32 Kbps-45 Kbps, Standard IP66, PoE (802.3af), lens ( 4.5mm - 135mm ) or equivalent high definition,IR range(Internal / Exteral) 150-200 mtr, motion detection, Analytics required with Licences for mentioned Analytics (Line crosing, Loitering, Tracking, Counting, Forensic search), with ONVIF Profile S supported, in built micro SD card slot up to 128 GB, connectors complete as required PTZ for mounting on wall or surface mounted with back box and adapter plate complete as per tender specifications required. (For Outdoor area) th laid specification or upto the satisfaction of engineer in charge.
Supply, installation, testing and commissioning of 32-channel NVR/NAS with 24TB with RAID5 configure,NVR /NAS should be 32camera licences as required & Analytics Licences for Functioning of Item No.2 & 3 should be considered, NVR with video input as required for Camera mentioned above in Item no. 1.Third-party network cameras supported, H.265 Compression - Up to 3 Megapixels resolution recording, Hard Disk of minimum 6 TB as required for minimum 60 days recording required for viewing @ 25 Frames per second and one megapixel resolution (Real Time) and recording @25 Frames per second. HDD quota and group management, 4 SATA interfaces, 2 USB2.0, Recording on Motion, Scheduled or Alarm based. Remote backup through TCP/IP, HTTP Networkable, backup by USB/DVDWR, Same OEM ONVIF Video management & recording software , min 5 user License (Client), complete as required in accordance with laid specification or upto the satisfaction of engineer in charge. th laid specification or upto the satisfaction of engineer in charge.
Supply installation Testing and commissioning of 24 Port Layer 2 Switch 10/100/1000BASE-T,4 x1GE port should be upgradable to 10GbE SFP+ in same hardware, 1 Fixed AC PSU, 1 RPS port. RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASET/100BASE-TX: half or full; 1000BASE-T: full only 4 SFP 100/1000 Mbps ports Should support AVB and SDN. Should support sflow/NetFlow/jflow and IGMP, MLD.
Supply installation Testing and commissioning of 12 Port Layer 2 Switch 10/100/1000BASE-T, 2x1GE port should be upgradable to 10GbE SFP+ in same hardware, 1 Fixed AC PSU, 1 RPS port. RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASET/100BASE-TX: half or full; 1000BASE-T: full only 2 SFP 100/1000 Mbps ports Should support AVB and SDN. Should support sflow/NetFlow/jflow and IGMP, MLD.
Supply Installation Testing & Commissioning of 4U outdoor Pole mount cabinet Rack with dual pole mounting clamp with IP6 rated with Dual Channel for rack mount support with FAN and MCB power supply. Rack should be air perfurated and watter proof and suitable for outer envirnment. Rack body should be powder coated paint with rust free. Rack should have 2 cable manger with 5 socket PDU.
SITC of 12U Equipment Rack with provision for housing all control equipment with front & rear door, Blower for cooling and proper locking arrangements. Rack should have depth of 550 MM and PVC 4 cable manager with cable separator, 15 AMP X6 power socket PDU with MCB,mounting hardware with earthing provision. as per the specifications, complete in all respect upto the entire satisfaction of Engineer - in - Charge of the work.
Supply Installation Testing & Commissioning of 43" LED Monitor, Full HD, HDMI Port, Component Video Inputs, 1 Digital Audio Out.
Supply Installation Testing & Commissioning of 3 Core Power Cable 1.5 sqmm.
Supply Installation Testing & Commissioning of CAT 6 UTP Cable.Transmission frequency of 250 MHz (Minimum),cable Should be 4 pair and Cable should be jacket FR PVC Lbp 69% required with certification report.
Supply installation & testing of Cat6 RJ45 Keystone Jacks-White Color complete in all respect to the entire satisfaction of engineer in charge
Supply installation Testing and commisioning of Cat 6 Field Termination Plug.
Supply installation Testing and commisioning of Back box and face plate set 3x3 forRJ45 face plate.
Supply ,Installation ,Testing and Commissioning of Cat6 UTP 24-26 AWG Patch Cord - 1mtr with cross separator, Manufactured from stranded wires for flex-life, Minimum length 1m, LSZH (Low Smoke Zero Halogen) standards like IEC 60332-1
Supply and erection of PVC pipe25mm dia ISI marked ( Medium ) recessed in wall / ceiling etc. including the cost of PVC bends , inspection boxes , iron hooks and cement concrete etc. complete in all respect upto the entire satisfaction of Engineer-in-charge of work
Supply installation ,testing and commisioning of 3KVA UPS Overvoltage cut-off device (OVCD),Support for up to 90 AH external battery cabinets, Generator Compatible with Wide Input. Wide Input Voltage window (110 – 280Vac) for IndianEnvironmental Condition andfor Optimized BatteryPerformance. UPS should be display the digital contents and warranings on screen.UPS would support SNMP Managaer and web browser On Line With 20 min Backup
Estimate of Access Control System, Visitor Management Solution
A. Access Control System
Software, Server & Access Controller
Supply, Installation, Testing, Commissioning of Intelligent Access Management Software shall be designed and configured in such a way so that single point failure will have no degradation in overall functionality, shall have distributed Architecture, shall have both Access & Time Attendance system in single interface and the one database only, ACS software must be integrated with Multiple OEMs Access Controllers & Smart Card Readers.
Supply, Installation, Testing, Commissioning of operator/ user Management Software license, shall be designed and configured in such a way so that single point failure will have no degradation in overall functionality, shall have both Access & Time Attendance system in single interface, shall support graphycal interface of the premises from where operator can manage and control.
Supply, Installation, Testing, Commissioning of 10/100 based IP based two reader controller shall support integration with OPIN based software, can be program as either to protect two doors with a single reader, or in/out reading on a single door, built-in 4 input and 2 output for Door position switch, Request to exit and door lock as minimum, Shall support Card holder capacity: 250000 as minimum & Event buffer in offline mode: 99000 as minimum, UL294, EN 301 489-3 EN 55022 EN 50130-4 (EU), FCC and as per technical specification and with all necessary power supply, battery back-up and Enclosure.
Reader and Credentials
Supply, Installation, Testing, Commissioning of Mobile Enabled Multitechnology Smart Card Reader, shall work on transmit Frequency of 2.4GHz & 13.5MHz, Support, Shall support consistent user experience across different devices and operating systems, including iOS and Android. The readers can be configured to using a smartphone with a “tap” or “Twist and Go” gesture technology and specification as per technical specification. Bluetooth SIG certification, UL-294, FCC, CE, RoHS II, BIS,.
Supply, Installation, Testing, Commissioning of High Security 8K Contactless smart card can store data for multiple application, shall support multi-layered trusted management of secure identities using the portable Secure Identity Object data model, shall support traceable identifiers exchanged during card sessions, preventing data associated to a card from being divulged or cloned. badge must be available under the same technology both for passive 13.56 MHz contactless badges and for virtual badges hosted in smartphones operation via Bluetooth low energy or NFC interface. Support AES-128 bits cryptographic algorithms for data protection and specification as per technical specification.
Networking Components
Supply, Installation, Testing, Commissioning of Layer 2 Gigabit Ethernet standalone chassis in a 1/2 U form factor with 8 nos 10/100/1000 BaseT PoE+ ports and 2 combo uplink ports, Minimum Switching capacity 20 Gb/s and Minimum throughput 35 Mbps, PoE power budget of 120W & as per features mentioned in technical specification.
Networking Components - Passive
Supply, Installation, Testing, Commissioning of Category 6 Unshielded Twisted Pair 4 pair 100W cable shall be compliant with ANSI/TIA/EIA-568-C.2 Additional Transmission Performance Specifications for 4-pair 23AWG, UTP, 100W Category 6 Cabling as per technical Specification.
Gate Management System
Supply, Installation, Testing, Commissioning of door lock suitable for single leaf door with holding force of 600lbs as per technical specification.
Supply, Installation, Testing, Commissioning of door monitoring sensor for monitoring door opening and closing as per technical specification.
Supply, Installation, Testing, Commissioning of manual call point (green colour) for emergency opening the door as per technical specification.
Cable & Conduit
Supply, Laying, connecting and testing of 6 core, 0.75sq.mm multi strand cable to connecting readers to controller .
Supply, Laying, connecting and testing of 6 core, 1 sq.mm multi strand cable to connecting door lock and door sensor to controller.
Supply, Laying, connecting and testing of 3 core, 1 sq.mm multi strand power cable.
Supply , Installation, Testing and commissioning of MS Conduits of following dia, complete with all accessories:
25mm dia
25 mm/20 mm dia GI Flexible Conduit
B. Visitor Management System
Supply, Installation, Testing, Commissioning of Server – Client Architecture built on .NET Platform & Back end database supporting Microsoft SQL Server. The deployment shall be in such a way where the client could be connected through LAN (Local Area Network), Wide Area Network (WAN) as well through internet in another location, shall be a single point management for managing Visitors, Vendors, Contractors, including the Sub Employees of the contractors, Vehicles coming to the facility, fully expandable & futuristic with provision to integrate with multi-location Access Control & Time Attendance System as per technical specification.
Supply, Installation, Testing, Commissioning of 360 deg swivel mount, HD, web camera for visitor image capture as per technical specification.
Supply installation Testing and Commissioning of Intel Core i7 or better Min 3.4 GHz, 8MB Cache or better with 16 GB RAM or better operator workstation. It should run on latest Windows® platform Enterprise 64-bit or latest. It should have 1TB storage. 1 DVI-I + 1 HDMI + 1 VGA, max 2 Monitor Output, 22inch LCD monitor, Optical Mouse, Keyboard, DVD writer.
Supply, Installation, Testing, Commissioning of Indirect Electrostatic Photographic Method/ OPC / Laser Printing Heat Roller Fusing based multifunction printer as per technical specification.
Variable Refrigerant Flow Air-conditioning System
EQUIPMENT WORK ( HIGH SIDE ) Supply, Installation, Testing & Commissioning of Variable Refrigerant Flow type multi unit air-conditioning system complete with indoor and outdoor units with individual controller for cooling & heating type operations. System shall be BMS compatible, contractor shall be shall be responsible for coordination between BMS and Airconditioning. Supply/ Installation of Modular type VRF Outdoor System, equipped with Efficient Scroll 100% Inverter compressor, Hot & Cold both option, special acrylc precoated heat exchanger, low noise condenser fan, auto check function for connection error, auto address setting of following capacity. Outdoor shall be capable to operate in Ambient conditions ( Cooling / Heating ) from -5 Deg C to 52 Deg C and from -15 Deg C to 24 Deg C. VRF / VRV must be equiped with Variable Energy Efficiency Regulation device feature which shall be enabling the ODU to perform in #3 Modes (Basic Mode / Turbo Mode and High Efficiency Mode) with varied EER in all three modes. Outdoor Unit No De-Ration of capacity upto 39°C, shall be in accordance to new RAMA guidelines. Auto Dust Removal, DC Motor Drive for Comressor motor and Condensing Fan Brushless DC Fan Motor, 0.5 W stand by power, Auto Restart Function, All Round Voltage Protection with Voltage fluctuations withstandable upto +/- 15%, With Enhanced DC Inverter Scroll compressor and Sub Cooling circuit technology, the ODU shall be capable to feed indoor unit at a distance of 240 RMT, with an Outdoor to Indoor elavational difference of 110 RMT and Indoor to Indoor elevational difference of 30 RMT. The ODU shall be capable to have commulative piping of 1000 RMT.
40 HP ( Minimum 4 Nos Compressor );Must be Modular Type. Should have COP of 4.0 @ 100% load and 6.2 @ 50% load at AHRI Conditions.
38 HP ( Minimum 4 Nos Compressor );Must be Modular Type. Should have COP of 4.0 @ 100% load and 6.2 @ 50% load at AHRI Conditions.
36 HP (Cooling & Heating ) ( Minimum 3 Nos Compressor );Must be Modular Type. Should have COP of 4.0 @ 100% load and 6.2 @ 50% load at AHRI Conditions.
30 HP for TFA ( Minimum 2 Nos Compressor );Must be Modular Type. Should have COP of 4.0 @ 100% load and 6.2 @ 50% load at AHRI Conditions.
16 HP ( Minimum 1 Nos Compressor );Must be Modular Type. Should have COP of 4.0 @ 100% load and 6.2 @ 50% load at AHRI Conditions.
Treated fresh Air Units Supply Installation Testing and Commissioning of Treated Fresh Air Units with EXV Valve. Supply, installing, testing and commissioning of factory built Ceiling suspended double skin type Treated Fresh air handling units made of 40 mm thick panels consisting of G.I. Casing of thickness 0.63 mm outside layer 0.63 mm thickness inside layer with polyurethene foam (PUF) insulation of density not less than 38 Kg/Cum factory injected between them by injection molding machine, complete with blower section with blower, cooling coil section with aluminum finned copper tubes (tube thickness not less than 0.5mm), 6RD ,suitable for 220+- 6% volts, 50 HZ, 1 Phase, A.C. supply, drain connections, stainless steel drain pan to be connected with existing VRF system.
2500 C.FM. Capaciity
Indoor VRF Units Supply Installation testing and commissioning of Indoor VRV Units Hi-wall /ceiling mounted cassette type Normal (3X3) and Compact (2X2)/ Slim Ductable unit, as specified. The indoor unit shall have independent electronic control valve to control the refrigerant flow rate respond to variations of the air-conditioning load of the room. The fan shall be aerodynamically designed turbo multiblade type. Statically and dynamically balanced to ensure lowest noise. The cooling coil shall be made of seamless copper tube. The tube shall be hydraulically or mechanically expanded and tested for 21 Kg/cm2. Indoor units shall have a wired remote control. They shall be operated through from the wired remote control from the respective rooms. Indoor Units- Ceiling Suspended Cassette Type
Indoor Units- Ceiling Suspended Ductable Type
Indoor Units- Wall Mounte Type
SITC of fittings, Y-joints set , including distributor and headers for all Indoor units as per layout drawings include ODU pipe connection kit etc complete as required.
Supply,Installation, testing and commissioning of Cordless/Corded remote controllers for operation of Indoor unit
Supply, Installation, testing & commissioning of Main Intelligent central controller system suitable for above indoor/outdoor units to operate, Schedule, monitor, on/off, temperature setting etc as required.
LOW SIDE WORK
Supply, Installation, Testing & commissioning of interconnecting suitable sized as per Drawing/Design - copper refrigerant pipe work duly insulated with (19mm/13mm thick) elastomeric nitrile rubber type tubular insulation between indoor & outdoor units as per specifications. All piping shall be laid on cable tray to be provided as required.
41.3 mm O.D.(insulation : 19 mm)
38.1 mm O.D.(insulation : 19 mm)
31.8 mm O.D.(insulation : 19 mm)
28.6 mm O.D.(Insulation : 19mm)
25.4 mm O.D.(insulation : 13 mm)
22.2 mm O.D.(insulation : 13 mm)
19.1 mm O.D.(insulation : 13 mm)
15.9 mm O.D.(insulation : 13 mm)
12.7 mm O.D.(insulation : 13 mm)
9.53 mm O.D.(insulation : 13 mm)
6.35 mm O.D.(insulation : 13 mm)
Providing and fixing of PVC Class V (10 Kg/Sq.cm. grade ) drain water piping of suitable size complete with fittings, support as per specification and insulated with 6 mm thick closed cell elastomeric nitrile rubber insulation etc as required. Cost to include necessary wall chasing etc. as per site conditions.
25mm dia.
32mm dia.
40mm dia.
Supply, installation, balancing and commissioning of on factory fabricated GSS sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, vanes, hangers, supports etc. as per approved drawings and specifications of suitable sheet thickness complete as required as per IS:655.
24 Gauge
Supply, installation, testing and commissioning of closed cell Nitrile rubber insulation of following thickness applied with Proper adhesive and sealed with 50 mm wide BOPP Tape on all longitudinal/ transverse joints complete as per specifications. 9 mm thick on ducts in conditioned space
Supply, installation, testing and commissioning of 32 kg/m3 density fiberglass insulation in the form of 25 mm thk fibre glass roll finished with Tissue paper and 28 gauge perforated Aluminum sheet with nuts, bolts complete as per specifications. 25 mm thickness acoustic lining
Supply, Installation, Testing and Balancing of Powder coated extruded aluminum construction Linear Grilles as per approved drawings and specifications. Quoted price shall be without volume control damper at the location of air collar
Supply, Installation, Testing and Balancing of GI collar dampers for supply air collars as per approved drawings and specifications.
Providing and fixing Fire retardant non porous double layer flexible canvass connection between each indoor unit and duct as per approved drawings and specifications.
POWER & CONTROL CABLING
Supplying, laying, testing & commissioning of following sizes of PVC Copper insulated FR flexible wire for communication between indoor, outdoor and centralized controller etc. in pvc conduit complete as required.
3 x 1.5 Sq. mm
(E). ESTIMATE FOR LIFT WORK
Design, manufacture , supply ,installation ,testing and commissioning of 15 passanger (Gear Less Machine Room Less) lift, with travel speed 1.5 MPS serving different floors in the lift shaft including automatic rescue device lift well pressurization as per detailed specification/drawing enclosed and as under: Technical specification Quantity 1 ( One ) unit(s) 1. Alarm button in car operating panel with battery back-up 2. Automatic operation for car fan 3. Adjustable door open time 4. Anti-nuisance (empty car) 5. Anti-nuisance (car call cancellation at direction reversal) 6. Blower fan in car for ventilation 7. Braille on push buttons 8. Car call cancellation by double pressing floor button in car operation panel 9. Door open and door close buttons in car operating panel 10. Door closing retries 11. Door nudging 12. Emergency light 13. Full load by-pass 14. Home landing 15. Infra-red screen for car door 16. Intercom 17. Jammed landing operating panel call button by-pass 18. Motor overheat protection 19. Overload function with audio-visual indication in car operating panel 20. Phase failure and phase reversal protection 21. Automatic rescue device in case of power failure 22. Attendant control 23. Red dot matrix scrolling display in car operating panel 24. Red dot matrix scrolling display in landing operating panel on All Floors 25. Fireman control scope of work 1. Supply of materials/components/parts of elevators/escalators of Product containing features as listed under Technical Specifications - Annexure 1 2. Installation, testing and commissioning of elevators/ escalators at site as listed under Technical Specifications- Annexure 1 3. Material transportation, marine/ inland Insurance 4. Unloading of material at site 5. Supply and erection of suitable scaffolding (as per approved GAD) inside elevator shaft/escalator pit for entire installation period and dismantling/removal of the same after completion of Works. Note: If in company’s’ scope, scaffolding shall be used for elevator installation works only and not for shaft preparation works etc. Also, the company may use scaffoldless method for installation works, at its own discretion. 6. Provision of minor builders’ works (details as per GAD) The rates shall be inclusive GST ,Contracter's profit and of all labour, men & material.The price shall remain valid for complete material /components shipment and completion of installation,testing and commissioning works of elevators , material and components.item to be completed in all respect as per drawing & instructions from Project in charge/Architect.
(F). ESTIMATE FOR LANDSCAPE WORK
Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 4.75 mm
Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)
Cutting of designer hedge/edge removing of cut materials, cleaning, hoeing of hedge/edge bed watering manure and applying insecticides and fungicides etc.(excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge.
Edging with bricks laid dry length wise, including required excavation,refilling, consolidating with hand packing and spreading surplus earth neatly within a lead of 50 m : 2.19.1 Common burnt clay F.P.S (non modular) bricks of Class designation 7.5
Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge.
Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately): Holes 90 cm dia, and 90 cm deep.
Complete maintenance of trees (Out side garden features), jobs like making of basin at regular interval i/c watering, weeding, pruning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department and other T & P material/articles shall be provided by the contractor) and as per direction of officer in charge.: Trees for 250 no/(up to 4 & up to 3 year Slow & Fast Per Plant/ growing group).
Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water): Shrubs Plant
Complete maintenance of shrubs (Out side garden features), jobs like making of basin at regular interval i/c watering, weeding, pruning & application of fertilizer etc, (excluding the cost of material which shall be supplied by / the department) and as per direction of officer in charge.
GROUND COVERS
Providing and stacking of Aspidistra, having 10 to 15 leaves well developed with fresh & healthy in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.
Providing and stacking of Chlorophytum (Green), full of leafy suckers in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.
Providing and stacking of Daniella variegated, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.
Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.
Providing and stacking of Ipomea (Golden leaves),with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.
Providing and stacking of Iresine herbstii, of height 20-25 cm. full of branches well developed in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.
(FLOWERS) Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge.
Antirrhinum dwarf
Chrysanthemum double
Gazania hybrid
Salvia
( FLOWERS) Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge.
Cosmos hybrid
Vinca Hybrid
Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge.
Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. including hoeing,weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawn mover and brush cutter with fuel and other T & P material/articles shall be provided by the contractor.) and as per direction of officer in charge. Permanent office accommodation.(1Mali for 1.25Acre)
Maintenance of Potted Plants at Nursery in Earthen pot including resetting/ displaying at Nursery, inculding watering, weeding, hoeing, colouring, transplanting the damaged pots and disposal of generated garbage at specified place as per direction of officer-in-charge. (Note:-Good earth, manure, fertilizer, insecticide & pesticide will be provided by the/ department) (Earthen pot 3000 nos)
Providing and Displaying Cyclamen hybrid variety fresh & healthy in full bloom well developed in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
Providing and Displaying Geranium double variety having 30 cm ht., in different colour well developed with fresh & healthy foliage (3 in one) well bloomed in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
Providing and Displaying Poinsettia dwarf multi head, having upto 30 cm ht., with 3 to 4 branches with fully different colored top with fresh & healthy foliage well developed in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
Providing and Displaying Tulip Dutch hybrid variety (3 in one) in each pot in full bloom fresh & bright in different colour well developed in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos vertical “ U “ shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge.: POT-Top inside dia 30 cm, outer bottom dia 20 cm, total height 30 cm with wall thickness of 25.4 mm
TREES
Providing and stacking of Cassia javanica of height 120-150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Ficus infectoria (Pilkhan) of height 150-165 cm. in big polybag of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Fishtail palm of ht. 210-240 cm bottom girth 25- 30 cm well developed in big size HDPE bags as per direction of the officer-in-charge.
Providing and stacking of Grevillea robusta (Silver Oak) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Lagerstroemia flosreginae of height 150-165 cm.in big poly bag of size 25 cm as per direction of the officer-in-charge.
SHURBS
Providing and stacking of Bauhinia acuminata height 60-75 cm. in earthen pots of size 20 cm as per direction of the officer-in-charge.
Providing and stacking of Chandni dwarf of height 15-20 cm., well branched in earthen pots of size 20 cm as per direction of the officer-in-charge. As per direction of the officer-in-charge.
Providing and stacking of Ficus blackii (F.vivion) of height 45-60 cm. with 6- 8 branches healthy foliage in earthen pots of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Largerstroemia indica of height 45-60 cm. in polybag of size 20 cm as per direction of the officer-in-charge.
(G). ESTIMATE OF STP
SOLAR POWER PLANT
Solar photo Voltaic Power Generation System Supplying , installation testing and commissioning ofgrid interactive roof top solarphoto voltaic power generation system including spaceframe( 40 KWH ) 40 KWp On Grid Solar Power Plant consisting of following with complete installation at site: • 40 KW On Grid Solar Inverter -01No • 320-360W (24V) “MNRE approved” Solar PV Panels -40KWp • Standard Roof Top GI Structure - As per requirement • Cables, Wires and connectors - As per requirement • Other Electrical accessories - As per requirement • Earthing Work - As per requirement 1) Solar PV Module: a) The solar photovoltaic modules will be used Poly/Multi crystalline, Thin film PV technology modules. b) The capacity of each Solar Modules should be equal to or greater than 300Wp. Solar Modules to be used have to be framed only. At locations where there is constraint of space, it should be considered higher efficiency modules only. c) Module would be PID Free and of positive Tolerance only. d) Modules would have an efficiency of not less than 16% and the fill factor should be above 75%. e) Minimum dimension of the SPV module shall be preferred. f) Each SPV Module would have IEC/BIS test certificate from any recognized IEC accredited or MNRE approved laboratory. g) The SPV modules would confirm to the minimum technical specification laid down by MNRE that can be referred on the MNRE website. h) The PV Modules shall be tested for Salt Mist Corrosion Test as per MNRE requirement. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years Inverter: The Inverter/s used would be robust, intelligent On-grid inverters of reputed manufacturer/makes. The inverter/s must conform to the IEC 61683 and IEC 60068-2, IEC 62116, IEC 61727. The typical specifications required are as under: All inverters should be 3 phase, 415V, 50Hz AC output, The AC capacity of the Inverter can be minimum of 80% of the connected DC capacity to the inverter. Minimum Start Voltage should be greater than 200V, MPPT Range: 200V-800V, Maximum Input Voltage: 1000V DC, Euro / CEC Efficiency above 97%, Frequency: 50Hz +/- 1.5%, Power Factor > 0.99, THD < 3%, Ambient Temperature range: -5 deg C to + 60 deg C, Warranty: 5 Years Comprehensive warranty. This warranty from the manufacturer shall be in addition to the scope covered under defects liability period Integrated Ground Fault Protection Anti Islanding Feature Transformer less Over Voltage/ Under Voltage Protection Auto Shut down in case or Over Heat/ Over Temperature
Providing and installation of Rainwater harvesting pit strictly as per sketches, drawings and detailed specification mentioned below. The agency approved by the Engineer-in-charge/ Contractor should have sufficient experience of having executed Rainwater harvesting pits in site. The job shall include maintenance cost and successful working of rainwater harvesting pit minimum period of 10 years. Boring for rain water recharge 635mm dia & depth of 30 Mtr, with 200mm perforated pipe 30 Mtr with SS filter of 3 Mtr at bottom, 6mtr 250mm, 6mtr 300mm pipe & Packing of Perforated Pipe & SS Strainer with 2mm - 4mm Washed Gravel. Making of rainBoring for rain water recharge 635mm dia & depth of 30 Mtr, with 200mm perforated pipe 30 Mtr with SS filter of 3 Mtr at bottom, 6mtr 250mm, 6mtr 300mm pipe & Packing of Perforated Pipe & SS Strainer with 2mm - 4mm Washed Gravel. Making of rain water recharge pit 6 Mtr. depth, upper part of pit will be 1.35 Mtr dia with 2 Mtr. depth, with filtration media of bolder stone 50/70mm-300mm, washed gravels 2/4-150mm, charcoal & activated carbon- 150mm, fine sand -150mm, fine sand and gravels2/4-150mm, bolder stone 50/70-300mm. and lower part of pit will be of 1350mm dia with 4 Mtr. depth for water holding. Making of silt trap 1.35 Mtr dia and 2 Mtr. Depth with layer of 50/70 – 500mm bolder with dual outlets and 24”x 150mm SS filter on both of outlets.
(J). Audio -Video Solution at GYM Area, Lounge area, Reception & Dining Area
Reception Area (Ground Floor & 5th Floor)
Supply Installation Testing & Commissioning of 43" LED Monitor, Full HD, HDMI Port, Component Video Inputs, 1 Digital Audio Out, Make: Christi/Panasonic/Samsung
Lounge Area
Supply Installation Testing & Commissioning of 55" LED Monitor, Full HD, 2 HDMI Port,USB, DVI, RS232 & RJ45, Built in speakers, Component video Inputs, 1 Didital Audio Out Make : SAMSUNG/SONY/CHRISTIE
Supply, Installation, Testing & commissioning of celling Mount Speaker with operation 6 Watts. Make Bosch/ JBL/ Tannoy
Supply Installation Testing and Commissioning of 90W Mixer amplifier,70 V / 100 V /8 ohm outputs,4 microphone/line inputs, plus 3 music source inputs Frequency response 50 Hz to 20 kHz (+1/‑3 dB @ ‑10 dB ref. rated output.Make: Bosch/Toa/Honeywell/Bose/Klipsch
Supply, installation, testing and commissioning of 2 core multistrand 1.5 sq mm annealed copper conductor speaker cable in existing pipe/ channel I/C connection etc. .Make: Krystal/beldon/Bonton
Supply and Erection of PVC pipe25mm dia ISI marked (Medium) recessed in wall/ceeling etc. including the cost of PVC bends, inspection boxes, iron hooks, cement concrete etc. complete in all respect up to the entire satisfacion of Engineer-in-charge of work Make : CUSTOM
Gym Area
Supply Installation Testing & Commissioning of 55" LED Monitor, Full HD, 2 HDMI Port,USB, DVI, RS232 & RJ45, Built in speakers, Component video Inputs, 1 Didital Audio Out Make : SAMSUNG/SONY/CHRISTIE
Supply Installation Testing and Commissioning of 240W Mixer amplifier,70 V / 100 V /8 ohm outputs,4 microphone/line inputs, plus 3 music source inputs Frequency response 50 Hz to 20 kHz (+1/‑3 dB @ ‑10 dB ref. rated output.Make: Bosch/Toa/Honeywell/Bose/Klipsch
Supply Installation Testing and Commissioning of 30 watt or better -wall mount Speaker with woofer & Dome Tweeter-Sound pressure level at rated power / 1 W (1 kHz, 1 m)-105/90 dB (SPL),Rated input voltage 15.5/70/100 V, power Taping 30/15/7.5/3.75 W, Effective frequency range (-10 dB)-100 Hz to 19 kHz, Opening angle at 1 kHz Safety 166° horizontal/140° vertical, EN/UL Water and dust protected IP65 .Make: Bosch/Toa/Honeywell/Bose/Klipsch
Supply, installation, testing and commissioning of 2 core multistrand 1.5 sq mm annealed copper conductor speaker cable in existing pipe/ channel I/C connection etc. .Make: Krystal/beldon/Bonton
Supply and Erection of PVC pipe25mm dia ISI marked (Medium) recessed in wall/ceeling etc. including the cost of PVC bends, inspection boxes, iron hooks, cement concrete etc. complete in all respect up to the entire satisfacion of Engineer-in-charge of work Make : CUSTOM
Dining Area
Supply Installation Testing & Commissioning of 65" 4K UHD LED, HDMI Port, Component video Inputs, 1 Didital Audio Out, wifi ready, Built in speaker, RS232, Make : SAMSUNG/SONY/CHRISTIE
Supply Installation Testing and Commissioning of 90W Mixer amplifier,70 V / 100 V /8 ohm outputs,4 microphone/line inputs, plus 3 music source inputs Frequency response 50 Hz to 20 kHz (+1/‑3 dB @ ‑10 dB ref. rated output.Make: Bosch/Toa/Honeywell/Bose/Klipsch
Supply, Installation, Testing & commissioning of celling Mount Speaker with operation 6 Watts. Make Bosch/ JBL/ Tannoy
Supply, installation, testing and commissioning of 2 core multistrand 1.5 sq mm annealed copper conductor speaker cable in existing pipe/ channel I/C connection etc. .Make: Krystal/beldon/Bonton
Supply and Erection of PVC pipe 25mm dia ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks, cement concrete etc. complete in all respect up to the entire satisfacion of Engineer-in-charge of work Make : CUSTOM
(K.) Digital Conference system
Supply Installation Testing and Commissioning of Digital Chairman Unit with fixed microphone with flexible stem can be easily adjusted to suit the user- long 480- 500 mm ,Built-in loudspeaker with volume control,Built‑in volume control for headphones,Possible-to-speak indication,Request‑to‑speak indication,GSM immunity,Frequency response 200 Hz to 12.5 kHz,Loudspeaker nominal output 72 dB SPL,Color-coded LED indicator above microphone button for showing the following states: microphone on, request‑to‑speak, and possible‑to‑speak Light‑ring indicator in head of microphone, cable and accessories as required. Make: Bosch/Toa/Taiden/Marconi/Audio Technica/Sennheiser
Supply Installation Testing and Commissioning of Digital Delegate Unit with fixed microphone with flexible stem can be easily adjusted to suit the user- long 480- 500 mm ,Built-in loudspeaker with volume control,Built‑in volume control for headphones,Possible-to-speak indication,Request‑to‑speak indication,GSM immunity,Frequency response 200 Hz to 12.5 kHz,Loudspeaker nominal output 72 dB SPL,Color-coded LED indicator above microphone button for showing the following states: microphone on, request‑to‑speak, and possible‑to‑speak Light‑ring indicator in head of microphone, cable and accessories as required. Make: Bosch/Toa/Taiden/Marconi/Audio Technica/Sennheiser
Supply Installation Testing and Commissioning of Digital conference system controller with connection of with 30 Discussion Devices and expandable upto 200 Delegate Units,Built‑in MP3 recorder with internal memory and USB recording,Built‑in Digital Acoustic Feedback Suppression (DAFS) for ensuring superior speech intelligibility, support for automatic HD camera control,Web browser control for configuration,Built-in monitor loudspeaker,built-in loudspeaker and headphone socket allows for:live monitoring of a meeting , indicators for showing-Open microphone,Mains power on/off,Plus/minus buttons for setting the volume range, RJ45 Ethernet,USB recording LED indicator Make: Bosch/Toa/Taiden/Marconi/Audio Technica/Sennheiser
Supply Installation Testing and Commissioning of 15 watt or better -wall mount Speaker with woofer & Dome Tweeter-Sound pressure level at rated power / 1 W (1 kHz, 1 m)-105/90 dB (SPL),Rated input voltage 15.5/70/100 V, power Taping 30/15/7.5/3.75 W, Effective frequency range (-10 dB)-100 Hz to 19 kHz, Opening angle at 1 kHz Safety 166° horizontal/140° vertical, EN/UL Water and dust protected IP65 .Make: Bosch/Toa/Honeywell/Bose/Klipsch
Supply Installation Testing and Commissioning of 240 W Mixer amplifier,70 V / 100 V /8 ohm outputs,Frequency response 50 Hz to 20 kHz..Make: Bosch/Toa/Honeywell/Bose/Klipsch
Supply Installation Testing and Commisioning of wireless Lapel Microphone with -32 preset channels, with compatible groups of eight (8) channels for simultaneous use14 hour battery life from two (2) AA alkaline batteries , Rugged metal transmitters with backlit LCD display and battery gaugeNumber of Channels: 32 Modulation: ± 40 kHz ,Diversity: True Antenna RF Sensitivity: <1.0 μV for 12 dB SINAD,Image Rejection: > 55 dB ,Squelch: Tone Code plus Amplitude,Frequency Response: 80 Hz – 18 kHz ± 2 dB,Balanced Output: 20 dBV (max @ 40 kHz deviation), Unbalanced Output: Adjustable 8 mV to 0.755V RMS,Distortion: < 1.0%, 0.4% typical,Signal-to-Noise Ratio: > 100 dB Make: Electrovoice/Audiotechnica/Sennheiser/Shure
Supply Installation Testing and Commisioning of wireless handheld Microphone with -32 preset channels, with compatible groups of eight (8) channels for simultaneous use14 hour battery life from two (2) AA alkaline batteries , Rugged metal transmitters with backlit LCD display and battery gaugeNumber of Channels: 32 Modulation: ± 40 kHz Diversity: True Antenna RF Sensitivity: <1.0 μV for 12 dB SINAD Image Rejection: > 55 dB Squelch: Tone Code plus Amplitude,Frequency Response: 80 Hz – 18 kHz ± 2 dB Balanced Output: 20 dBV (max @ 40 kHz deviation) Unbalanced Output: Adjustable 8 mV to 0.755V RMS Distortion: < 1.0%, 0.4% Signal-to-Noise Ratio: > 100 dB Make: Electrovoice /Audiotechnica /Sennheiser /Shure
Supply installation testing Commsioning of projector having resolution 1024 x 768 pixels XGA–WUXGA, Brightness: 4,100 lm Light source, Supported video signal; NTSC/PAL/SECAM, 480p/i, 720p, 1080p/i, lifetime: Up to Normal: 5,000 hours, Inputs: 1x HDMI 1.4 / DVI-D / HDBaseT / VGA (D-Sub 15 pin) / RJ 45 Ethernet , Keystone correction range :30 ° x 15 ° (Manual), Operating temperature: 5 -40 °C Make: Panasonic /Sony/christie
Supply installation testing Commsioning of projector screen motorized with size 8" x 6" with remote control. MAKE: Suvira/Drapar
Supply Installation Testing & Commissioning of 55" LED Monitor, Full HD, HDMI Port, Component video Inputs, 1 Didital Audio Out Make : SAMSUNG/SONY/CHRISTIE
Supply Installation Testing and Commisioning of a distribution amplifier for HDMI signals which equalizes the signal and distributes it to identical outputs, should have 1 HDMI input and 4 HDMI out with max data rate 6.75Gbps, with showing LED status, Make: Kramer/Extron/Crestron/ATEN
Supply Installation Testing and Commissioning of Popup Box, Pop–Up Table Mount Multi–Connection Solution, Elegant in–table compact solution, CE qualified, 4 Fixed Inputs — 15–pin HD, HDMI, 3.5mm & Ethernet. PORTS - HDMI connector, Ethernet RJ–45 connector, 15–pin HD connector, 3.5mm mini jack, Make: Kramer/ Extron/ Crestron/ ATEN
Supply installation testing Commsioning of 5 Meter HDMI male to HDMI male cable for input. Make: Kramer/Extron/Crestron/Aten/MX
Supply installation testing Commsioning of 20 Meter HDMI male to HDMI male cable for input. Make: Kramer/Extron/Crestron/Aten/MX
Supply, installation, testing and commissioning of 2 core multistrand 1.5 sq mm annealed copper conductor speaker cable in existing pipe/ channel I/C connection etc. .Make: Krystal/ beldon/ Bonton
Supply and Erection of PVC pipe25mm dia ISI marked (Medium) recessed in wall/ceeling etc. including the cost of PVC bends, inspection boxes, iron hooks, cement concrete etc. complete in all respect up to the entire satisfacion of Engineer-in-charge of work Make : CUSTOM
Supply,Installation,Testing and Commisioning of 17U rack for switch Mounting with Fan and power strip,PDU,Hardware Mounting Kit (Make : Comrack/APW/Netrack/Perfect Rack)
VSK INFRASTRUCTURES PRIVATE LIMITED
Shree Gautam Construction Co. Ltd.
stage.html
html • 0.03 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid