SPECIAL REPAIRS TO BLDG No. P-97 ORs MARRIED ACCN (TOTAL QUARTERS -08 Nos) KALIDHAR LINE AT 14 GTC SUBATHU UNDER GE KASAULI

Amount

Demolition of cement concrete (un re-inforced) in ground floor and paving n.exc. 15 cm thick below or above ground level complete all as specified .

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified.

Dismantling PVC drain or vent pipe of any description in any position including bends branch pieces etc. Complete all as specified.

Taking down cement plaster on brick wall surfaces etc including raking out joints hacking for key, scrubing down with water etc complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar complete all as specified.

Demolition of brick work or stone boulder masonry built in cement mortar complete all as specified.

Taking down chowkhats or frame with shutter (without taking off shutters from the frames) n.exc. 1.5 Sqm complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exceeding 1.5sq.m and not exc 4.00sq.m each of any description including making good the disturbed surfaces complete all as specified.

Dismantling plain or corrugated steel sheeting any guage thickness including Nainital pattern as in roof covering complete all as specified.

Brick work with sub class 'B' bricks of class designation 10 all as per IS-1077-1992 (minimum compressive strength of brick 100 kg/Sqcm) old size bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6, complete all as specified.

Rendeing 10mm thick on other than fair faces in CM 1:6 finished even and smooth with out using extra cement complete all as specified.

Rendering 5mm thick in CM (1:3) on fair faces of concrete surfaces as in ceilling finished fair and even without using extra cement complete all as specified.

Plain Cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in seismic and other similar bands, shelves, copings, bed plates, hold fasts, plinth courses, filling in pressed steel frame and the like finished fair and even including necessary form work complete all as specified.

75mm thick plain cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection finished fair and even without using extra cement complete all as specified. Note:- Plinth protection shall be laid in pannels and length of the each panel shall not be more than 2.00 mtr all as directed. 6mm joints filled with 85/25 grade bitumen and sand (1:3 ratio) shall be provided. No deduction for joints shall be made while making payment against the above item.

PCC 1:3:6 type C2 (using 40mm graded stone aggregate as in surface channel / drains complete all as specified.

Extra for forming fair finished drain or channel 30 cm inner girth in forms, moulds/stopped ends etc.complete all as specified.

RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in shelves / slabs and like including use and waste of necessary form work complete all as specified.

Mild steel TMT Bars 10mm dia and over cut to length, bend to shape required, including cranking, bending, for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges etc. fixed all as per manufactures's instructions and fixed with self thread making steel screws of length not less than 50mm complete all as specified.

Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges, flashing, eaves board valley gutter of any shape etc, cut to designed shape (Jhhallar) as directed at site fixed all as per manufactures's instructions and fixed with self thread making steel screws of length not less than 50mm complete all as specified.

MS flat sections of size 40x6 mm as in wind tie complete all as specified.

Non Skid ceramic tiles 7 to 8 mm thick area exc 0.18 sqm n exec 0.38 sqm in floors, set and jointed in neat cement slurry and pointed in white or colored cement to match with the tiles including 15 mm thick screed bed or bedding layer in C.M 1:4 etc complete all as specified.

Non Skid ceramic tiles 7 to 8 mm thick area exc 0.18 sqm n exec 0.38 sqm in skirting, set and jointed in neat cement slurry and pointed in white or colored cement to match with the tiles including 10 mm thick backing coat in C.M 1:4 etc complete all as specified.

Non Skid ceramic tiles 7 to 8mm thick area exc 0.11 Sqm but n exc 0.18 Sqm (square / rectangular) as in floors set and jointed in cement slurry and pointed in coloured cement including provision of screed bed 15mm thick in CM (1:4) complete all as specified.

Coloured glazed ceramic tiles in vertical surface 350 x 250 x 7mm / 450 x 350 x 7mm thick set & jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm screed bed in 1:4 cement mortar complete all as specified.

Pressed steel frames of size 105 x 60 mm thickness 1.25mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete all as specified.

Pressed steel frames of size 125 x 60mm thickness 1.25mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete all as specified.

Factory made steel windows with side hung shutters including box type hinges with steel handle, tower bolt and steel peg stay complete with glazing bars complete all as specified.

Factory made steel windows with fixed type including box type hinges with steel handle, tower bolt and steel peg stay complete without glazing bars complete all as specified.

Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified.

Framed work such as grills, gratings, etc with ends of bars shouldered and / or riveted, or forged into spikes , framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings , framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified.

Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples complete all as specifeid.

Sheet glass , ordinary quality & glazing 3mm thick, with oil putty in square n. exc 0.5 Sqm in each pane complete all as specified.

Figured glass 4mm thick, pin head type and glazing with oil putty in square n. exc 0.5 Sqm in each pane complete all as specified.

Second class hard wood factory made plain, framed, panelled shutters , 35mm thick (Hollock) with lock rail and panels of 9mm thick commercial ply or 12mm thick veneered particle board with commercial veneer on both sides, including priming coat, duly hammer marked. The size of rail & style shall be as per IS 1003 Part-1 kiln seasoned and chemically pressure treated including one coat of pink primer complete all as specified.

Second class hard wood 30mm thick glazed and skeleton shutter factory made open rebated and prepared to receive glass, guage etc with plain chamfered or rounded mitred and rebated, sash bars in any numers divided into squares edges of framing, plain or chamfered or rounded as specified in SSR Pt-I, section 8, clause 8.24(a) supplied and fitted to chowkats complete all as specified.

Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm wood grain printed PVC sheet reinforced with MS square tube etc complete all specified.

Factory made solid PVC moulded door shutter 28 to 30 mm thick (stiles) with 2, 4 (or) 6 raised panel design with 2 mm thick 3D wood grain moulded PVC sheet polyurethene painted on the front face and 2 mm plain colur PVC sheet on back face with particle board core etc complete all specified.

20mm dia anodised aluminium alloy curtain rails with fixing brackets fixed in repair complete all as specified.

Second class hard wood small fittings such as brackets of any type latch and hinges blocks shaped door and window stops and the like, including all necessary labour, articles n.exc. 200 cucm each complete all as specified.

Cold rolled mild steel medium weight butt hinges 100 mm, ISI marked, complete all as specified.

Aluminium anodised barrel tower bolts extruded section of size 200 mm complete all as specified.

Aluminium anodised barrel tower bolts extruded section of size 150 mm complete all as specified.

Aluminium anodised extruded handles of size 150 mm complete all as specified.

300 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded sections, bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts ,fixed on plate or staple plate complete all as specified.

Prepration of newly plastered wall surface and applying two coats of oil emulsion distemper over and including 1mm thick white cement based wall care putty complete all as specified.

Preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

Preparation of new or previously untreated surfaces of wood or based materials of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

Preparation of surfaces of steel and iron work, new or old , as in small articles such as hold fasts etc and treating with tar or coal tar black paint, area tarred not exc 0.10 sqm each complete all as specified.

Taking up or down 15 mm dia steel tubing and connection and removal from site complete all as specified.

Taking up or down 20 mm dia steel tubing and connection and removal from site complete all as specified.

Steel water tubing medium grade galvanized with all fittings and fixed complete to walls andceiling or laid into floor 15 mm bore complete all as specified.

Steel water tubing medium grade galvanized with all fittings and fixed complete to walls andceiling or laid into floor 20 mm bore complete all as specified.

Refixing old 15 mm GI tubing and connections on new or old position (walls, ceilling, floor etc) complete all as specified.

Refixing old 20 mm GI tubing and connections on new or old position (walls, ceilling, floor etc) complete all as specified.

15mm dia bib tap chromium plated long body screwed with wall flange for iron pipe and fixed in repair complete all as specified.

Wash hand basin, vitreous china, white, decorative type, flat or angle back, size 550 mm x 400 mm including cutting for and pinning in ends of brackets or erecting stand including waste pipe , fixed in repairs complete all as specified.

15mm pillar tap cast copper aloy with capston heads chromium plated screwed down screwed for iron pipe or for brass ferrule fixed in repair complete all as specified.

Brass chromium plated tubular towel rail 20mm dia D type 60 cm long between flanges fixed in repair complete all as specified.

Grating doom 100 mm dia of PTMT (Min wt 25g) fixed in repair complete all as specified.

Dismantling water tanks n.exc 500 ltrs capacity and removing to store complete all as specified.

500 ltr capacity rotational moulded polythene water stoarage tanks ( clyndrical vertical with closed top) three layered hoisted and fixed in position complete all as specified.

20 mm dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipes etc, fixed in repair complete all as specified.

10 litres capacity PVC flushing cistern valve less syphonic action type, low level white with inlet, ball valve , float including brackets and PVC flush pipe 32 mm dia fixed in repair complete all as specified. .

Angle stop valve, brass chromium plated fancy type, screwed down, high pressure with crutch or butterfly handle screwed down , screwed for iron pipe or for union, suitable for 15 mm bore pipe, fixed in repair complete all as specified.

15mm dia PVC connection 450 mm long with brass nut, fixed in repair complete all as specified.

Vitreous china squatting pan, "Orissa Pattern" size 580 x 440 mm white with integral foot rest and flush pipe fixed in repair complete all as specified

Stop valve cast copper alloy 20 mm bore screwed down high pressure with crutch or butterfly handle scewed both ends for iron pipe or for unioin fixed in repair complete all as specified

Soap dish chromium plated of size 180 x 160 x 90 mm any type, fixed with chromium plated brass screws complete all as specified.

Brass chromium plated shower rose 125mm with swivel joints fixed to steel pipe or union fixed in repair complete all as specified.

Sink with drainage board made out of stainless steel sheet 1.0 mm thick with plug, washers and wastes, overall size 915mm x 460 mm, bowl size 410 mm x 330 mm x160 mm including fixing cantilever brackets and connection to union, pipe, fixed in repairs complete all as specified.

Stainless steel plate rack of size 24" x 36" x 10" deep made out of 1.00 mm thick sheet ISI marked, fixed in repair complete all as specified.

110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified.

75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified.

75 mm dia PVC (SWR) bends with oval access door with rubber ring joints fixed as required complete all as specified.

110 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement including necessary PCC & form work as required complete all as specified.

75 mm dia PVC (SWR) junction single, (single T), equal or un equal with oval access door including jointing with solvent cement as required complete all as specified.

110 mm dia PVC (SWR) junction single, (single T), equal or un equal with oval access door including jointing with solvent cement as required complete all as specified.

110 mm dia PVC (SWR) branch piece, single, equal or un equal of any length including jointing with solvent cement as required complete all as specified.

75 mm dia PVC (SWR) branch piece, single, equal or un equal of any length including jointing with solvent cement as required complete all as specified.

110 mm dia PVC (SWR) reducer, single, equal or un equal of any length including jointing with solvent cement as required complete all as specified.

75 mm dia PVC (SWR) vent cowl, single, equal or un equal of any length including jointing with solvent cement as required complete all as specified.

18 to 20mm thick black granite stone for cooking platform, as in steps, pillars, window cills, and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the marble, full rounding of corners/edges and cutting to make it square or rectangular, cuttting and polishing with machine to achieve granite finish complete all as specified. Note : Size of the slabs shalll not be less than 100 cm x 60 cm.

Pre-laminated particle board 19mm thick, exterior grade pre laminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber / steel frame work as in shelves or shutters or wall panelling, fixed in repairs complete all as specified.

Piano hinges, mild steel bright finish width of flap 40 mm fixed in repair complete all as specified.

Magnetic catches brass body for use in cup boards of kitchen, ward robes etc. fixed in repair complete all as specified.

40 mm dia cupboard knob of brass, polished, fixed with nut screw and washer, fixed in repair complete all as specified.

Hasp and staple 75 mm mild steel wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified.

Water proofing treatment of sunken floor of WCs, bathroom etc. comprising of following:- (i) Cleaning of sunken floor surface with mechanical means i.e. wire brush/air blower etc. and remove all loose/unsound material, dirt, dust, etc. (ii) Applying cement slurry mixed with acrylic based polymer modified cementitious composite compound coating Hydroproof Xtra of FOSROC/Equivalent of Dr Fixit of Pidilite Industries Ltd in the ratio of 1:2:4 (One part of acrylic polymer : Two part of water and four part of cement). (iii) First layer of cement slurry @ 0.444 Kg/Sqm mixed with acrylic based modified cementious composite compound @ 0.222 Litre/Sqm and allow it to air dry for 04 hours. (iv) Second layer of cement slurry @ 0.222 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.111 Litre/Sqm and allow it to air dry for 04 hours followed with water curing for 48 hours. (v) 200 micron thick polythene film shall be pasted with help of adhesives over treatment.

Note :- Joints of WC / Trap / Soil waste shall be properly sealed with sealing compound. Testing of all traps and joint and sunken slab shall be done as per IS-1742 before filling and tiling work.

Plain cement concrete 1:5:10 type E-2 (using 40 mm graded broken bricks aggregate) as in foundation, filling and mass concrete, complete all as specified.

25 mm thick plain cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in levelling course laid and compacted in slope in floor complete all as specified.

GI metal suspended ceiling system fixed in repair OREO GI lay in plain of make DEXUNE / HUNTERDOUGLS / LINDER 600 x 600 x 0.5mm (TEGULAR) Edge tiles in global white colour to be laid on strong 24 mm T-section flanges colour white having rotary stitching on the main runner with web height of 38 mm, tiles shall have humidity resistance of 100% with light reflection of 62% Note: (i) To comprise main runner spaced at 1200 mm centres securly fixed to the structural soffit at 1200 mm maximum centre. The first / last suspension system at the end of each main runner shall not be greater than 450 mm from the adjacent wall. Flush fitting 1200 mm long cross tees to be interlocked between main runners at 600 mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600 mm require independant support. 600 x 600 mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 3000 x 19 x 19 mm, secured to walls at 450 mm maximum centres

(ii) Suspension system accessories consisting of HLC sleeve anchor fasterners of thread size 6.5 mm x 25/5 with soffit cleat made of galvanised steel of size 27 x 37 x 25 x 1.6mm and level clip in dimensions of 85 x 30 x 0.8 mm with 4mm GI wire

100 mm thick cement concrete 1:3:6 type C-2, (using 20 mm graded stone aggregate) as in sub floors, filling and mass concrete etc complete all as specified.

Screed bed or bedding layer of cement mortar 1:6, 15mm thick for laying floor finishes complete all as specified.

Coloured Chequred cement concrete tiles (30 cm x 30 cm x 25 mm thick) in grey cement and with pigment in floors etc , set and jointed in neat cement slurry, complete all as specified.

Taking down carefully copper/AImn point wiring (Light, Fan / Point Socket or power) (fittings such as switches ceiling roeses, pendent, regulators, sockets etc to be measured & paid seprately) & making good to disturbed surface of walls / floors etc. complete all as specified.

Point wiring using approved colour coding as per IS with stranded copper conductor single core 1.5 Sqmm (Nominal area), FRLS PVC insulated cable in and including PVC conduit (ISI marked) including cutting chiseling and grouting concealed PVC conduit pipe, tee, elbow and bend etc.and with all connecting accessories, mild steel sunken boxes suitable for mounting switch / sockets with earth dolly duly painted with two coats of anti corrosive paint over a coat of red oxide primer, mounting frame over cover plate, covered with 3mm thick plastic laminated sheet, PVC insulated copper conductor 1.5 Sqmm (Nominal area) single core FRLS PVC cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified for the following:-

One light / fan point controlled by one switch

One switch socket outlet 3 pin,5 Amp on the independent board

One switch socket outlet 3 pin,5 Amp on same board

One light point controled by two 2 way switches

One bell / buzzer point controlled by one push button on the same board with other switches.

Point wiring using approved colour coding as per IS with stranded copper conductor single core 2.5 Sqmm (Nominal area), FRLS PVC insulated cable in and including PVC conduit (ISI marked) including cutting chiseling and grouting concealed PVC conduit pipe, tee, elbow and bend etc.and with all connecting accessories, mild steel sunken boxes suitable for mounting switch / sockets with earth dolly duly painted with two coats of anti corrosive paint over a coat of red oxide primer, mounting frame over cover plate, covered with 3mm thick plastic laminated sheet, PVC insulated copper conductor 2.5 Sqmm (Nominal area) single core FRLS PVC cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified for 6 pin 16 Amps socket outlet on independent board.

Point wiring using approved colour coding as per IS with stranded copper conductor single core 4 Sqmm (Nominal area), FRLS PVC insulated cable in and including PVC conduit (ISI marked) including cutting chiseling and grouting concealed PVC conduit pipe, tee, elbow and bend etc.and with all connecting accessories, mild steel sunken boxes suitable for mounting switch / sockets with earth dolly duly painted with two coats of anti corrosive paint over a coat of red oxide primer, mounting frame over cover plate, covered with 3mm thick plastic laminated sheet, PVC insulated copper conductor 4 Sqmm (Nominal area) single core FRLS PVC cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified for 6 pin 16 Amps socket outlet on independent board.

Bell push, 6 Amps, SP, flush type complete all as specified.

Electric Bell , AC 230 volts, single pole complete all as specified.

Switch piano, flush type, single pole 2 way 6 Amp,ISI marked complete all as specified.

Lamp holder,PVC insulated body, with back plate suitable for batten fitting complete all as specified.

Switch piano, flush type, single pole 1 way 6 Amp,ISI marked complet eall as specified.

Switch piano flush type, single pole 1 way 16 Amp complete all as specified.

Socket 5 pin 6 Amp piano flush type,ISI marked complete all as specified.

Socket out let 2 in one 6 pin 6 & 16 Amp complete all as specified.

Ceiling rose, 3 phase/ PVC/ polycorbonate,isolated body complete all as specified.

LED bulb 10 watt complete all as specified.

Self ballasted LED batten extruded thermoplastic body with PC diffuser in square shape type fitting pre-wired for and including LED tube 18/20 watt 6500K 4 ft IP20 linear LED basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver complete all as specified. Make : Philips Cart No BN 021 LED25S 6500 PSU GR S1 or its equivalent in the makes mentioned in Appendix 'B'.

Decorative wall light fixture made up of polycarbonate , fancy type, made out of polycorbaonate,suitable for B-22 base holder 12 watt fixed in repair complete all as specified. Make: Polycab cat No. PGR0301010 or its equivalent in the makes mentioned in Appendix 'B'.

Sleek LED mirror light with diffuser 7/ 9 watt along with all accessories prewired including connecting with copper flexible cable of size 0.7 Sqmm 3 core complete all as specified. Make: Wipro Cat No LL20-111-XXX-65-NE or its equivalent in the makes mentioned in Appendix 'B'.

Bulk head luminaire decorative energy saving new generation 10W LED IP65 with opal diffuser including electronics driver & connection with copper flexible cable 3 core complete all as specified. Make Philps Cat No WT202W LED6S NW PSU S2 PC or its equivalent in the makes mentioned in Appendix 'B'.

LED building security light 25 /30 watt pressure die cast housing with individuals LEDs & Lens with modular secondary optics and IP65 protection with electronics driver and copper conductor 3 core of 0.7 sqmm from ceiling rose to security light with bracket made out of GI light grade pipe of 32 mm bore 1.5 mtr long bent to an angle of 120 degree with fixing arrangements on wall fixed in repair complete all as specified. Make: Wipro Cart No LR02-331-XXX-57-XX or its equivalent in the makes mentioned in Appendix 'B.

Wall Mounting LED fitting 9/12 watt 6500K 2 ft basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver complete all as specified. Make: Philips cat No.BN021C LED20S PSU CW GR S2 or its equivalent in the makes mentioned in Appendix 'B.

Sheet metal enclosure with double door for DBs conforming to IS:8623.III , IP:43 protection, shrouded neutral bar and cement spill protector, 8 way, 240 Volt SPN complete all as specified.

Sheet metal enclosure with double door for DBs conforming to IS:8623.III , IP:43 protection, shrouded neutral bar and cement spill protector, 4 way, 415 Volt TPN complete all as specified.

MCBs 'B' characteristics, double pole , 240 V, 32 Amp breaking capacity 10 kA complete all as specified.

MCBs 'B' characteristics, four pole , 415 V,63 Amp breaking capacity 10 kA complete all as specified.

MCB B characterstic single pole 5 to 30 Amp, 240 volt breaking capacity 10 kA complete all as specified.

Submain wiring with 2 single core PVC insulated FRLS cable 6 Sqmm copper conductor PVC sheathed drawn in and including rigid PVC concealed conduit heavy duty of suitable size including cutting chases in wall and making good disturbed surface of walls / floor etc with plastering painting etc to match with the existing finishes, drawn with 6 Sqmm PVC insulated FRLS copper conductor cable for earth wire fixed with saddle and connecting to common earth teriminals complete all as specified. Note : Three runs of 6 sq mm cable and one run of PVC conduit shall be measured as one unit.

Blanking plate complete all as specified.

Single pole and neutral sheet metal enclosure with a 2 pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified.

S & F Non mettalic Electric meter box with single hinged door for 01 No. Single phase meter of size 250 X 200 X 105 mm after disconnecting the supply of electric meter and fixing the electric meter on meter box incl reconnecting the electric supply. Make: Sintex CAt part No. GSMB 2520 or in Equivalent in Hensel / Clipsal

Supply & fix fans ceiling complete with electronic type regulator and accessories 230 V,1200 mm sweep. BEE 5 star rated

Exhaust fan, energy efficent metalic blades heavy duty turbo force of size 300 mm sweep, 900 rpm, AC, 230 volts complete with louvers, shutters, mounting on walls with holding down bolts, nuts, washers and cutting holes into or through stone/brick walls for fixing of 300 mm sweep exhaust fan including making good the cutting to match with the existing surface and connection of flexible copper conductor cable three core from ceiling rose to fan and testing complete all as specified.

Earthing complete with and including galvanised steel earth plate electrode 60 cmx 60cm x 6 mm thick surrounded by mixture of charcoal and salt in alternate layers , buried directly in ground vertically in a pit of depth not less than 2.25 meter deep below ground level with top edge of the at a depth of not less than 1.5 mtrs below normal ground level connected to galvanized iron or steel earth lead wire 4.0 mm dia,( NO 8 SWG) by means of bolts ,nuts, check nuts and washers of galvanised iron or steel earth wire protected by galvanised steel pipe 15 mm bore (light grade) and connected to main switch or main control board all as shown in electrical plate No. 3 of MES Schedule Part - I & including necessary excavation and earth work in any type of soil, 20 mm bore GI pipe (Light grade ) for watering , protection pipe funnel, wire mesh ,

Item No.135 contd /- PCC 1:2:4 type B1 chamber in cement concrete ,50 mm thick precast RCC M-25 ( Normal mix) cover duly reinforced with XPM (weight not less than 3 kg /sqm ) and CI frame etc , and including provision of test point , connecting to test point and testing on completion etc, complete all as specified. NOTE : Unit rate quoted shall include the cost of earthing lead and protection pipe upto 7.5 metre from top of earth plate.

LT XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sq mm 4 core confirming to IS specification including taking out existing unserviceable cable, laid in trenches, testing and commissioning complete all as specified.

Excavating in trenches, n.exc 1.5 m wide and n. exc 1.5 m in depth for laying cable , pipe and getting out in soft/loose soil complete all as specified.

Returning , filling in, including spearding, levelling , wateing and well ramming in layers not exc 25 cm complete all as specified.

Removing excavated soil to a distance n exc 50 M and depositing where directed at a level n exc 1.5 m above the starting point complete all as specified.

Sand filling under floors or in foundations including watering and consolidation complete all as specified.

Continuous brick edging with width equal to the depth of the brick of whole sub class 'B' bricks laid on edge complete all as specified.

Tubes, light grade, galvanised 40 mm bore with all fittings laid in trenches complete all as specified.

M/s Parmod Kumar

PRITPAL SINGH

Rajesh Agencies

M/S SHANTI SARUP DINESH CHAND