PROVN OF AIR CONDITIONER AND ALLIED WORKS SERVICES AT OTES HALL HQ MC U AT VSN NAGPUR

Dismantling of wall and celling board (fiber, pulp, insulation, etc) or insulation board / slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed.

Material & labour for providing 10mm thick Plaster of Paris (POP) false ceiling (gypsum anhydrous) to flat or curved surface as per design approved over GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (of any length) of 0.55 mm thickness having curled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre all as per manufacturer’s instructions including two coats of oil bound distemper over a coat of primer over a coat of putty complete all as specified and as directed.

Demolition of brickwork or stone /boulder masonry built in cement mortar complete all as specified and as directed.

Material & labour for earthing complete with galvanised steel plate electrode, 600 x 600 x 6 mm thick, buried directly in ground (earth pit not less than 2.25 mtrs deep below nominal ground level) with top edge of the plate not less than not less than 1.5 metres below nominal ground level connected to earthing lead of 4 mm dia galvanised iron or steel wire all as shown in plate No. 4 of SSR PART 1 of 2009 to the earthing test point all as specified and as directed. Note :- the cost of excavation and earth work PCC pit and RCC cover funnel & watering pipe, wiremesh, charcoal dust and common salt earth lead protection pipe upto 7.5 Rmt shall be deemed included in the unit rate for earthing complete all as specified and as directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. fair finished surfaces complete all as specified and as directed.

Taking down cement plaster on brick or stone wall,concrete, etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

All as per item No 10 above but 5 mm dia & over upto & incl 10 mm dia in stirrups

Material & labour for rendering 15 mm thick in CM 1:6 over brick /stone wall/block wall/concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Material & labour for rendering 15mm thick on fair finish of bricks/concrete/stone surface of wall in CM (1:4) using WPC and finished the surface even and smooth without using extra cement (WPC to be mesuared and paid separately) complete all as specified and as directed.

Material & labour for preparation of new plastered surfaces of walls and applying 1mm thick wall care putty in two layers of opposite direction for making the surface even & smooth and applying 2 coats of oil bound distemper with roller over a coat of alkali resistant primer complete all as specified and as directed.

Material & labour for preparation of new plastered wall surfaces and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm complete all as specified and as directed. Note :- Shade and pattern of the colour to be approved by GE.

Material & labour for complete removal of existing treatment of wall surfaces and applying 1mm thick wall care putty and making the surface even & smooth by rubbing and applying one coat of alkali resistant primer and applying distempering two or more coats with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete all as specified and as directed.

Material & labour for complete removal of existing treatment by washing, rubbing down and stopping of painted surfaces of walls, chajjas, columns, beams etc and finishing with two coats of acrylic smooth exterior paint (100 % acrylic) applied @ 1.67 ltr/10 Sqm over and including priming coat of exterior primer (acrylic base) applied @ 2.20 kg/ 10 sqm in any pattern by using different tints of any height complete all as specified and as directed.

Material & labour for PCC 1:3:6 type C-0 using 12.5mm aggregate crushed stone aggregate as in filling back side of pressed steel door/window frames complete all as specified and as directed.

Supply only integral water proofing compound ISI marked complete all as specified and as directed.

Supply & fixing sheet glass, ordinary quality in square but exc 0.50 Sqm each pane, 5.5 mm thick fixed to aluminium section complete all as specified and as directed.

Dismantling of stone stabs & tiles of any description or thickness in floor, aprons etc and bedded & pointed in cement mortar and disposing off debris to a distance up to 250M complete all as specified and as directed.

Material & labour RCC (Nominal mix) type B1 1:2:4 (20mm graded aggregate) for Beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and as directed.

Material & labour for grinding and polishing of existing floor of stone slab like marble, granite, kota etc by using mechanical grinder/floor polish machine and finally cleaning and treating the surface with beeswax polish etc complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Supply & fixing light shade vitrified tiles 8-9 mm thick (square/ rectangular) polished area of each tiles n.exc 0.36 sqm in floors, parking etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match in dark shade incl 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.

Material & labour for 25 mm thick cement concrete type B-0, 1:2:4 (12.5 mm graded aggregate) as on floor complete all as specified and as directed.

Dismantling asbestos cement, galvalume, fiber sheet (Plain, corrugated , semicorrugated, etc.) sheet in roof covering complete all as specified and as directed.

Supply & fixing Pre painted GalvaIume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws etc complete all as specified and as directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Material & labour for polished chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors complete all as specified and as directed.

Supply & fixing of steel work in tubular trusses, post, purlin, rafter etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and as directed.

Material & labour for cement concrete( 1:4:8) type D2 (40mm graded) in foundation filling and mass concreting complete all as specified and as directed.

Supply & fixing vitreous china wash hand basin, white, flat back of size 630 x 450 mm including waste coupling, CI brackets, PVC waste pipe and connection 32 mm bore complete all as specified and as directed.

Material & labour hard core of broken stone or boulders of gauge n exc 63 mm depossted, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface complete all as specified and as directed.

Supply and installation invertor based split AC of capacity 2.0 TON (Copper coil) electric driven single phase, 230 volts, 5 star rating including all accessories like brackets, rubber tubing, copper tubing, gas charging, with auto filter clean technilogy etc including testing and commissionin as per norms of BEE and alongwith digital type voltage stabilizer automatic operation single phase, designed for input variation between 130 V to 300 Volt with output voltage stabilized at 230 Volts sutaible for split AC of 2.0 TON and making good to the disturbed surface to match the existing surface complete all as specified and as directed. Make : Hitachi/LG/Blue star/Godrej/'O' General/Voltas Note :- (i) All cooing /condensing coil shall be made of copper material. (ii) Copper tubing including insulation required if extra is included in the quoted rate. No extra payment shall be made for extra piping. (iii) All necessary cutting of POP/ ceiling/wall if required is deemed to be included in the quoted rate. No extra payment shall be made on this acount.

Supply & fixing Decorative LED down light 36 watt recessed mounting type full lit luminaire with glare free uniform illumination with longer life and less maintenance, 2x2 Ft (>100 lm/W) complete with all accessories & connector etc internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed. Make : CG Cat Part No. LCTLRNE-36-FO-CDL or equivalent in Wipro/Philips.

Supply and fix power plug top suitable for AC of 2.0 Ton completer complete all as specified and as directed.

Supply and fix split AC stand of outdoor unit suitable for 1.5/2 ton including necessary fixing arrangement complete all as specified and as directed.

Taking down carefully sub-main wiring of any description and making good to ther disturbed surfaces to match the existing complete all as specified and as directed.

Taking down carefully any type point wiring (light, fans, socket etc) complete including battens and fittings such as switch, ceiling rose, light fittings, regulators, socket, etc. and making good disturbed surface of wall/floor, etc. complete all as specified and as directed.

All as per item No 89 above but 2.5 sq mm cable size with 2.5 sq mm earth continuity wire for one 3 pin socket outlet, 16 Amps on independent board complete all as specified and as directed.

RUNNING METRE

Supply & fixing socket modular type 6/16 Amps, 3 pin combine, 2 module,230 volts complete all as specified and as directed. Make : Legrand Cat No. 675555 or equivalent in Havells/ Anchor Panasonic (Roma plus)

Material & labour for sub main wiring (concealed/surface) complete with two single core 4 Sqmm FRLS PVC insulated unsheathed stranded copper conductor cable drawn through in and including 20 mm dia rigid non-metallic PVC conduit heavy grade and conduit accessories including 4 Sqmm FRLS PVC insulated unsheated stranded copper earth cable connected to common earth dolly complete and including cutting chasing in walls for concealed wiring using machine cutting and making good the disturbed surface complete all as specified and as directed. Note: 3 run of 4 sqmm & one run of PVC conduit shall be measured as single unit.

rbed surface complete all as specified and as directed. Make: Note: 3 run of 10 sqmm& one run of PVC conduit shall be measured as single unit.

Material & labour for sub main wiring (concealed/surface) complete with two single core 10 Sqmm FRLS PVC insulated unsheathed stranded copper conductor cable drawn through in and including 25 mm dia rigid non-metallic PVC conduit heavy grade and conduit accessories including 10 Sqmm FRLS PVC insulated unsheated stranded copper earth cable connected to common earth dolly complete and including cutting chasing in walls for concealed wiring using machine cutting and making good the distu

Supply & fixing for ceiling rose, surface bakelite, 65 x 50 mm, two to three terminals complete all as specified and as directed.

Taking down old u/s and Supply & Fix new master led tube 4ft 20 W LED batten of high-quality Materials and design, Extruded aluminum housing enhances safety, High quality PC Diffuser. Reliable and robust housing structure having nominal system lumen output of 2500 lumens and a minimum system efficacy of 125 lm/W. The luminaire shall have a rated system lifetime of 50,000 burning hours at L70.The luminaire should have a color temperature of 6500K and CRI>83. The luminaire shall meet IP20 rating with THD < 10% and PF > 0.95. The total power consumption should not exceed 20W (including driver) complete all as specified and as directed. Make : CG Cat Part No. CCS-100-20-65-HL2-DP-NWH or equivalent in Bajaj/ Wipro.

Supply & fixing 0-4 step, one module, modular type electronic regulator for ceiling fan 1200 mm sweep, 240 volts, 100 Watts humfree single pole, complete all as specified and as directed. Make : Legrand Cat No. 675531or equivalent in Havells/ Anchor Panasonic (Roma plus)

Supply & fixing sheet metal enclosures for SPN DB's with metal double door for incorporating MCBs,IP-43 , 12 way, 240 volts, as per IS-8623 complete all as specified and as directed. Make : Legrand Cat No 507612 or equivalent in Havells/ Anchor Panasonic (Roma plus)

Supply & fixing MCB SPN, 40-63 Amps, breaking capacity 10 KA 'C' curve confirming to IS/IEC 60898-1 2002,integrated label holder, sliding bottom clamp , IP 20 protected terminal, sliding shutters, 240 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc complete all as specified and as directed. Make : Legrand Cat No. 408617 or equivalent in Havells/ Anchor Panasonic (Roma plus)

(e) One switch socket outlet modular type 3 pin 6 amp on same board.

Taking down fan of any size and any make, sealing cable end, dismantling the fan blade and removing fan and blade to store complete all as specified and as directed.

Supply & fixing MCB SP 6-32 Amps, breaking capacity 10 KA 'C' curve confirming to IS/IEC 60898-1 2002,integrated label holder, sliding bottom clamp , IP 20 protected terminal, sliding shutters, 240 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc complete all as specified and as directed. Make : Legrandor equivalent in Havells/ Anchor Panasonic (Roma plus)

Supply & fixing socket modular type 6 Amps 3 pin 2 module 230 volts complete all as specified and as directed. Make : Legrand Cat No. 675551 or equivalent in Havells/ Anchor Panasonic (Roma plus)

Supply & fixing Switch modular type, single pole one way 6 Amps, 230 volts Ac suitable for modular switch boxes without indicator, complete all as specified and as directed. Make : Legrand Cat No. 675501 or equivalent in Havells/ Anchor Panasonic (Roma plus)

Supply & fixing new exhaust fan PVC body 10" ( 250 mm) sweep 230 V, 50 Hz, complete with all accessories & connector etc internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size, complete all as specified and as directed.

Supply & fixing Energy saving ceiling fan 1200 mm sweep min air delivery 210 CFM with double ball bearing in opal white colour and BEE 5 star rated BLDC complete including provision of 3 core copper wire of size 1.5 sqmm , connected from ceiling rose to fan and marking MES No in black paint complete all as specified and as directed.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and as directed.

Supply & fixing MCB SP 40-63 Amps, breaking capacity 10 KA 'C' curve confirming to IS/IEC 60898-1 2002,integrated label holder, sliding bottom clamp , IP 20 protected terminal, sliding shutters, 240 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc complete all as specified and as directed. Make : Legrand or equivalent in Havells/ Seimens/ L & T

Material & labour for laying & testing of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminum conductor of size 50 sqmm 3.5 Core all as per IS , complete all as specified and as directed.

Boring of hole under road/pavement/hard standing or any other situation by mannual means and suitable for passing of GI pipe 40 to 100 mm bore and making good both ends complete all as specified and as directed.