Construction Supply, Erection and Commissioning of New Vegetable and Fish Market at Diu (balance Work)

CIVIL WORKS :

(Civil Work) Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. All kinds of soil

Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete. Note : Local Available Sand to be used for filling. (Approved Exess quantity )

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/recoverable separately). All works above plinth level upto floor V level Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Providing, hoisting and fixing up to floor five level precast reinforced cement concrete in small lintels not exceeding 1.5 m clear span up to floor five level, including the cost of required centering, shuttering but excluding the cost of reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : In lime mortar

Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : In Cement Mortar

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts

Supply installation of steel structure with providing and fixing of PVC coated polyester fabric with PVDF topcoat of Ferrari / Mehler / Hiraoka or equivalent (inclusive of procuring, design, non-linear structure analysis, static analysis for steel structure, patterning, nesting, seaming, fabrication, with SS cables, nuts and bolts, alloy D-shackles transportation and installation, inclusive of crimping etc. complete), steel structure as per approved design with two coat epoxy paint as per direction of Engineer-in-charge

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo- Mechanically Treated bars

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 10.00 sqm and upto 16.80 sqm in the area

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Provdg. 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand) for interior plastering upto any floor level and finished even and smooth as directed by Engineer In Charge

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Granite of any colour and shade Area of slab upto 0.50 sqm

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Granite of any colour and shade Area of slab over 0.50 sqm

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. (Approved Excess Quantity)

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge Size of Tile 600 x 600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados,over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand)and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete : 125x64x2.50 mm

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete : 100x60x2.50 mm

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete : 75x50x2.50 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :200x10 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 150x10 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 100x10 mm

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing bright finished brass handles with screws etc. complete : 125 mm

Providing and fixing bright finished brass handles with screws etc. complete : 100 mm

Providing and fixing bright finished brass handles with screws etc. complete : 75 mm

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Finishing walls with Acrylic Smooth exterior paint of required shade after thoroughly orushing the surface to remove all dirt & remain of loose powdered materials: New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sq m over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Internal Wiring Supply, installation, connection, testing & commissioning of following outlet points as per Specification & IS. The unit rate for the point shall consist of the circuit wiring from LDB or switch board to outlet point through MCB / switch as required & including the outlet points with connector & sockets as per specification. All the wiring, outlet points shall be done in a surface / concealed manner with ISI approved medium duty, rigid FR PVC, ISI conduit of minimum 25 mm. dia. using 650 V FRLS copper conductor wire, modular switches with suitable plate, PVC / Metal back box with brass chromium / cadmium plated machine screws etc. Scope also includes the additional space in SB for further expantion, Space should be atlest for 2 nos. of 15 amp Plug & Switch. Point Wiring Wiring for the following light points with 3nos. 1.5 sq.mm FRLS flexible copper conductor 1100 volts grade wires of approved make in concealed or surface mounted 25 mm dia medium gauge PVC Conduit including providing and fixing of 6 amps single pole rocker operated flush mounted switch of approved quality color make & design in 2 mm thick GI box and earthing of fixtures and the outlet box with 1.5 sq.mm PVC insulated copper conductor stranded flexible "FRLS" wire.Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are of ISI marked FRLS PVC insulated multistrand copper wires, with pipe duly erected complete with 6A Tissino type switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic box covered with appropriate front plate modules erected concealed in wall / ceiling.

Primary light point controlled by one SP MCB (Double height light point only)

Point wiring for secondary light point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are of .ISI marked FRLS PVC insulated multistrand copper wires, with pipe duly erected complete with earth continuity and necessary connection with primary light with accessories erected on Metal/ PVC box covered with 3 mm thick laminated sheet for concealed wiring.

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & eirthwire of 1.5 sq.mm (green) both are of .ISI marked FRLS PVC insulated multistrand copper wires, With pipe duly erected complete with 6A Tissino type switches and following type of accessories erected on PVC / Metallic box covered with appropriate front plate modules erected concealed in wall / ceiling. Primary light point controlled by two, two way 6 A switch

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & eirthwire of 1.5 sq.mm (green) both are of .ISI marked FRLS PVC insulated multistrand copper wires, With pipe duly erected complete with 6A Tissino type switches and following type of accessories erected on PVC / Metallic box covered with appropriate front plate modules erected concealed in wall / ceiling. Secondary light point controlled by same switch

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are of .ISI marked FRLS PVC insulated multistrand copper wires, in existing pipe duly erected complete with 6A Modular type switch and hum free EME 5/6 step type electronic fan regulator with separately mounted and accessories with earth continuity of following type erected on PVC / Metallic box covered with appropriate front plate modules erected concealed in wall / ceiling

Wiring for the 250 volts single phase and neutral 6 amps switched socket outlet with 2.5 sq.mm FRLS flexible copper conductor 1100 volts grade wires of approved make in concealed or surface mounted with 25 mm dia medium gauge PVC Conduit including providing and fixing of 6 amps 5 pin switch socket outlet of approved quality color make & design in PVC / 2 mm thick GI box and earthing of fixtures and the outlet box with 1.5 sq.mm PVC insulated copper conductor stranded flexible "FRLS" wire. One 6 A x 5 pin 250 Volt socket outlet point controlled by one 6 A switch located on board.

Wiring for the 250 volts single phase and neutral 6 amps switched socket outlet with 2.5 sq.mm FRLS flexible copper conductor 1100 volts grade wires of approved make in concealed or surface mounted with 25 mm dia medium gauge PVC Conduit including providing and fixing of 6 amps 5 pin switch socket outlet of approved quality color make & design in PVC / 2 mm thick GI box and earthing of fixtures and the outlet box with 1.5 sq.mm PVC insulated copper conductor stranded flexible "FRLS" wire. 6 A x 5 pin 250 Volt switched socket outlet point at convenient location. ( Plug & Switch can be together or at different location)

Wiring for the 250 volts single phase and neutral 16 amps switched socket outlet with 2.5 sq.mm FRLS flexible copper conductor 1100 volts grade wires of approved make in concealed or surface mounted 25 mm dia medium gauge PVC Conduit including providing and fixing of 16 amps 5 pin switch socket outlet of approved quality color make & design in 2 mm thick GI / PVC box and earthing of fixtures and the outlet box with 1.5 sq.mm PVC insulated copper conductor stranded flexible "FRLS" wire.

Wiring for the UPS / Comp. / Raw Power outlet with 2 nos. of 250 volts single phase and neutral 16 amps switched socket outlet with 2.5 sq.mm x 3 core FRLS flexible copper conductor 1100 volts grade wires of approved make in concealed or surface mounted Prelaid 25 mm dia medium gauge PVC Conduit / Race ways including providing and fixing of 2 no.s of 16 amps 5 pin switch socket outlet of approved quality color make & design in 2 mm thick GI box and earthing of fixtures and the outlet box with 1.5 sq.mm PVC insulated copper conductor stranded flexible "FRLS" wire. ( Maximum 3 nos. of Plugs can be looped in 1 Circuit)

Wiring for the Three phase and neutral 32 amps polycarbonate industrial 5 pin (IP 65/66) socket outlet with 32 amps Four pole MCB in a poly carbonate enclosure with 4 x 6 sq.mm FRLS flexible copper conductor 1100 volts grade wires of approved make in concealed or surface mounted 50 mm dia medium gauge PVC Conduit including providing and fixing of 32 amps socket in poly carbonate enclosure and neutral & earthing pin of the socket and with FP MCB of approved quality color make & design in 2 mm thick GI box / polycarbonate enclosure and earthing of fixtures and the outlet box with 2 nos. of 2.5 sq.mm PVC insulated copper conductor stranded flexible "FRLS" wire.

Wiring for the Single phase and neutral 32 amps polycarbonate industrial 3 pin (IP 65/66) socket outlet with 32 amps Double pole MCB in a poly carbonate enclosure with 2 x 6 sq.mm FRLS flexible copper conductor 1100 volts grade wires of approved make in concealed or surface mounted 25 mm dia medium gauge PVC Conduit including providing and fixing of 32 amps socket in poly carbonate enclosure and neutral & earthing pin of the socket and with DP MCB of approved quality color make & design in 2 mm thick GI box / polycarbonate enclosure and earthing of fixtures and the outlet box with 2 nos. of 2.5 sq.mm PVC insulated copper conductor stranded flexible "FRLS" wire.

Supply and laying of 32 mm rigid PVC pipe of 1.6-1.8 mm thickness

Supply and laying of 40 mm rigid PVC pipe of 1.6-1.8 mm thickness

RACEWAYS & JUNCTION BOX Providing and fixing 2 mm thick steel sheet factory fabricated post galvanized raceway with internal partition of the following sizes including providing removable 3 mm thick GI cover, knock out holes and fixing accessories earthing with 8 SWG copper earth wire complete as required including floor supports, bends, access boxes, tap off boxes and cross over as per specification and site requirement. Providing and fixing 350 x 350 x 40 mm deep 2 mm thick GI sheet junction box including providing 3 mm thick stainless steel cover as per specification.

Providing and fixing 250 x 250 x 40 mm deep 2 mm thick GI sheet junction box including providing 3 mm thick stainless steel cover as per specification.

Providing and fixing 200 x 200 x 40 mm deep 1.6 mm thick GI sheet junction box including providing 3 mm thick stainless steel cover as per specification.

MAINS : ( not for Point wiring ) Supplying and Laying of mains with Cu. PVC insulated flexible wire with ISI and FIA approval for 650 V/ 1100 V with earth wires of Cu. PVC insulated flexible wires with ISI approval for 650 V/ 1100 V as earth wires to be drawn in Suitable dia rigid PVC Pipe of Heavy Gauge ( Scope Also includes Supply of with. ) Supplying and Laying of 4 nos. of 10 sq mm Cu. FRLS flexible wires with 2 nos 4 sqmm Cu. FRLS flexible wires to be drawn in 2 nos. of 40 mm dia Pipe

Supplying and Laying of 4 nos. of 6 sq mm Cu. FRLS flexible wires with 2 nos 2.5 sqmm Cu. FRLS flexible wires to be drawn in 2 nos. of 40 mm dia Pipe

Supplying and Laying of 2 nos. of 10 sq mm Cu. FRLS flexible wires with 1 nos 4 sqmm Cu. FRLS flexible wires to be drawn in 40 mm dia Pipe

Supplying and Laying of 2 nos. of 6 sq mm Cu. FRLS flexible wires with 1 nos 2.5 sqmm Cu. FRLS flexible wires to be drawn in 40 mm dia Pipe

Supplying and Laying of 2 nos. of 2.5 sq mm Cu. FRLS flexible wires with 1 nos 1.5 sqmm Cu. FRLS flexible wires to be drawn in 25 mm dia Pipe

Distribution Board Supply, Assembling, grouting, leveling Connecting & testing D.B of IP 43 of specified make Distribution Board-VTPN Supply, Erecting, testing and commissioning of only VTPN D.B. PPI type with space for FPMCCB as incoming and space for DPELMCB and 12 TPMCB as outgoing per phase (i.e. 12 way VTPN D.B.) of Legrand Make Cat. No. 607915

Distribution Board Supply, Assembling, grouting, leveling Connecting & testing D.B of IP 43 of specified make Supply, Erecting, testing and commissioning of only VTPN D.B. PPI type with space for FPMCB as incoming and space for DPELMCB and 8 TPMCB as outgoing per phase (i.e. 8 way VTPN D.B.) of Legrand Make Cat. No. 607751

Distribution Board Supply, Assembling, grouting, leveling Connecting & testing D.B of IP 43 of specified make Distribution Board-TPN Supply, Erecting, testing and commissioning of only TPN D.B. PPI type with space for FPMCB as incoming and space for DPELMCB and 12 SPMCB as outgoing per phase (i.e. 16 way per phase D.B.) of Hensel Make KV9354M

Supply, Erecting, testing and commissioning of only TPN D.B. PPI type with space for FPMCB as incoming and space for DPELMCB and 8 SPMCB as outgoing per phase (i.e. 12 way per phase D.B.) of Hensel Make KV9448M

Supply, Erecting, testing and commissioning of only TPN D.B. PPI type with space for FPMCB as incoming and space for DPELMCB and 4 SPMCB as outgoing per phase (i.e. 8 way per phase D.B.) of Hensel Make KV9336M

Distribution Board-SPN Supply, Erecting, testing and commissioning of SPN D.B. PPI type with space for DPELMCB as incoming and 8 SPMCB as outgoing per phase (i.e. 12 way D.B.) of Legrand make 607712

MCB All MCB's, ELMCB's, ELCB's should be of 10 KA only 6 to 32 A SP MCB

MCB All MCB's, ELMCB's, ELCB's should be of 10 KA only 6 to 32 A DP MCB

MCB All MCB's, ELMCB's, ELCB's should be of 10 KA only 25 A / 100 mA DP ELMCB

MCB All MCB's, ELMCB's, ELCB's should be of 10 KA only 32 A / 100 mA DP ELMCB

MCB All MCB's, ELMCB's, ELCB's should be of 10 KA only 40 A / 100 mA DP ELMCB

MCB All MCB's, ELMCB's, ELCB's should be of 10 KA only 63 A / 100 mA DP ELMCB

MCB All MCB's, ELMCB's, ELCB's should be of 10 KA only 6 to 32 A TP MCB

MCB All MCB's, ELMCB's, ELCB's should be of 10 KA only 40 A TP MCB

MCB All MCB's, ELMCB's, ELCB's should be of 10 KA only 63 A TP MCB

MCB All MCB's, ELMCB's, ELCB's should be of 10 KA only 25 A FP MCB

MCB All MCB's, ELMCB's, ELCB's should be of 10 KA only 32 A FP MCB

MCB All MCB's, ELMCB's, ELCB's should be of 10 KA only 40 A FP MCB

MCB All MCB's, ELMCB's, ELCB's should be of 10 KA only 63 A FP MCB

125 Amp. FP MCCB ( 16 KA ) with Spreader Link

Sheet steel enclosure for DP MCB

Sheet steel enclosure for FP MCB

125 Amp. MCCB ( 16 KA ) with the Enclosure & Both Side Cable end Box with the Handle with Spreader Link with On off Indicating Lamp

Cables Supply, Installation, Testing, Laying, Commissioning of following 1100 volt grade XLPE insulated PVC sheathed aluminum / Copper conductor armored cables as per (IS:7098)(I)-88 ISI marked & specification in trenches, cable trays, ducts, over bed of sand, clamped to wall with suitable clamps including, saddles fixing bolts, connecting testing and commissioning with identification tags at every 10 mtr. & Both ends. with All the fixing accessories, excavation Back filling & Cable protection with Bricks as per the drawing ( If required ). 70 sq.mm x 3.5c Al. XLPE Arm. Cable

Cables Supply, Installation, Testing, Laying, Commissioning of following 1100 volt grade XLPE insulated PVC sheathed aluminum / Copper conductor armored cables as per (IS:7098)(I)-88 ISI marked & specification in trenches, cable trays, ducts, over bed of sand, clamped to wall with suitable clamps including, saddles fixing bolts, connecting testing and commissioning with identification tags at every 10 mtr. & Both ends. with All the fixing accessories, excavation Back filling & Cable protection with Bricks as per the drawing ( If required ). 25 sq.mm x 4c Al. XLPE Arm. Cable

Cables Supply, Installation, Testing, Laying, Commissioning of following 1100 volt grade XLPE insulated PVC sheathed aluminum / Copper conductor armored cables as per (IS:7098)(I)-88 ISI marked & specification in trenches, cable trays, ducts, over bed of sand, clamped to wall with suitable clamps including, saddles fixing bolts, connecting testing and commissioning with identification tags at every 10 mtr. & Both ends. with All the fixing accessories, excavation Back filling & Cable protection with Bricks as per the drawing ( If required ). 10 sq.mm x 4c Al. XLPE Arm. Cable

Cable Termination SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, Double Compression Brass glands with earthing. Cable Termination SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, Double Compression Brass glands with earthing. 70 sq.mm x 3.5 c Al. XLPE Arm. Cable

Cable Termination SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, Double Compression Brass glands with earthing. 25 sq.mm x 4c Al. XLPE Arm. Cable

Cable Termination SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, Double Compression Brass glands with earthing. 16 sq.mm x 4c Al. XLPE Arm. Cable

Cable Termination SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, Double Compression Brass glands with earthing. 10 sq.mm x 4c Al. XLPE Arm. Cable

Light Fixtures & Fans Supply, installation, Testing & Commissioning of Light Fixtures with all necessary Lamps, Ballast etc.. Complete in all Respect Contractor has to supply the fitting as per architect / Consultants final approval. ( all the lamps should be of intermediate color only) 1 x 28 W type light fixture with 28W lamp of Philips make TWG 207 / 1 x TL5 28W Adreno V2

1 x 11 watt mirolta type light fixture with lamp equivalent to Philips make FMS200/111

Any kind of Light Fixture with Basic Rate of Rs.1500/-

Any kind of Light Fixture with Basic Rate of Rs.5000/-

Any kind of Light Fixture with Basic Rate of Rs.15000/-

Supply, Installation, testing and commissioning of Fans without fan regulator. 48" dia sweep high speed high breeze ceiling fans white in color.

Exhaust Fans : SITC of light duty propeller 225mm dia exhaust fans

Street Light Fixture Documentation & Certification from accredited international & national laboratories / agencies shall be provided by the manufacturer / contractor for the luminaries. Luminaries with all electrical accessories & it should be energy efficient, low loss, ortho cyclically wound open construction copper ballast (Ballast should be Step dimming with Timer as per detailed specification for 400 watt, 250 watt & 150 watt fitting), ignitor & power factor improvement capacitor etc are prewired up to the terminal block & mounted on a removable control gear module for ease of maintenance. All electrical connections of the control gear module with the rest of the luminaries should be click fix & foolproof & require use of no tools. Mounting options should be for both lateral as well as pole top mounting. Luminaries must have sufficient space & proper arrangement to accommodate the step dimming ballast with timer. IP 65 post top lantern with 70 watt CDM-T lamp including control gear, all accessories, complete in all respect of Philips make Berlin or Schreder make Jasper

Earthing Providing and laying of following tined copper / GI plate electrode, with 2 Nos 50 x 6 mm copper strips from earth plate electrode to inspection chamber, 50 mm dia medium class GI pipe, CI funnel with 20 gauge GI wire mesh, masonry chamber 1000 x 500 mm with concrete base C I heavy duty / chequered plate manhole cover with frame painted with bitumastic paint and packing with mixture of charcoal and common salt around plate electrode including digging of pit up to permanent moisture level and as per soil condition but not less than 3 meters and back filling as required. 600 x 600 x 3.15 mm cu.plate

Providing & doing earthing electrode for equipment earthing as specified in IS:3043 - 1987 for equipment complete with : Earthing Electrode Cu. Type - 19, 50 MM. Dia 3 Mtr. Long. ( OBO Betterman / Ashlok / LPI Make ) Contractor is responsible to achieve the Earthing Resistance less than 1 Ohm.

Earth wire/strips : Supply and laying cu. earthing strips for interconnecting the earthing stations, panels, DB's etc. in built up trenches, on walls/ceiling, buried in ground generally as specified and shown on drawings complete with : fixing accessories Corrosion protection of buried conductors with bituminous coating and covered with PVC tapes. 25 x 3 mm cu. Tape

Supplying and Laying mains with 1 no. of 6 sq mm Cu. PVC insulated FRLS flexible wire ( Green Color Only ) SITC of Water Tight Junction Box of Hensel make Cat. No. KG9003IN or equivalent. With necessary clamp for mounting of the J.B. ( All the cable / wire connections to the JB shall be with the Water tight Glands only )

Telephone Distribution Providing and installing of all conduiting and structured cabling for telephone system including providing and fixing of the following: All necessary specials and fittings Approved cover plates for inspection, junction and outlet boxes. 2 mm thick outlet boxes and junction boxes. All fixing accessories such as clips, nails, screws etc. Providing and fixing approved saddles, hooks and grouting the same as required, in the case of all exposed conduit work. Embedding conduits and accessories in wall, floors etc. during construction and / or cutting chases and making good as necessary in the case of all concealed conduit work. Supply and installation, testing and commissioning following size KRONE make telephone tag block in lockable 16 gauge sheet steel enclosure complete as required. 10 pair Krone type tag block

Telephone Distribution Providing and installing of all conduiting and structured cabling for telephone system including providing and fixing of the following: All necessary specials and fittings Approved cover plates for inspection, junction and outlet boxes. 2 mm thick outlet boxes and junction boxes. All fixing accessories such as clips, nails, screws etc. Providing and fixing approved saddles, hooks and grouting the same as required, in the case of all exposed conduit work. Embedding conduits and accessories in wall, floors etc. during construction and / or cutting chases and making good as necessary in the case of all concealed conduit work. Supply and installation, testing and commissioning following size KRONE make telephone tag block in lockable 16 gauge sheet steel enclosure complete as required. 5 pair Krone type tag block

PVC & HDPE Conduits Supply & laying of 25 mm dia. rigid PVC conduit of 2.0-2.2 mm thick heavy gauge with all accessories.

Supply & laying of 40 mm dia. rigid PVC conduit of 2.1 -2.3 mm thick medium gauge with all accessories.

Telephone Point Wiring Supply and laying of specified make 0.51 mm dia Tinned copper telephone wire of specified make to be done in prelaid PVC pipe of 25 mm dia/raceway of specified make, but without the cost of pipe or raceway. (the wire is to be drawn from Krone connector of respective area to outlet point ) 10 pair telephone wire

Telephone Point Wiring Supply and laying of specified make 0.51 mm dia Tinned copper telephone wire of specified make to be done in prelaid PVC pipe of 25 mm dia/raceway of specified make, but without the cost of pipe or raceway. (the wire is to be drawn from Krone connector of respective area to outlet point ) 5 pair telephone wire

Supply and laying of specified make Cat 6 wire of specified make to be done in prelaid PVC pipe of 25 mm dia / raceway of specified make, but without the cost of raceway or pipe ( the wire is to be drawn from HUB \ Switch of respective area to outlet point ) with the cost of the crimping with material

Telephone Outlet Point Supply and installation of flush mounted Category 6 T 568 A or B outlet. The plastic shall be high impact, flame-retardant UL rated thermoplastic. Dust cover / Blank shall be provided to protect unused face plate openings. Termination cap and plastic cover shall be provided to protect jack wiring. one telephone point to be done with telephone outlet socket RJ-11 (jack type) and box of the specified make.

one Data I/O point to be done with data outlet socket of RJ-45 and Face Plate, box of the specified make.

Miscellaneous Supplying & Erecting conventional type Carbon Dioxide fire extinguishers of ISI approved of 4.5 kgs

Supplying & Erecting automatic emergency light with maintenance free battery for 20 watts tube.

Supplying & Erecting Rubber mat 1.1 KV 1000 x 2000 x 6 mm

Providing and erecting danger notice board for medium voltage installation to be erected as per I.S. The board should be 150 x 150 mm.

Providing printed instruction chart both in English & REGIONAL LANGUAGE & duly framed out on glass for treatment of person suffering from Electric shock.

Supply & installation of 6 Mtr (Approx 20') high G.I. decorative Conical Column 4.0 mtr height above the ground level having top 75.0mm O.D. &bottom 140.0mmO.D. with avg. thickness of 3.0mm. The column shall also be provided with flush door at the bottom with proper strengthening to the cutout of the door opening. A junction/ looping box with 32 Amps heavy duty connector shall be built into the pole. street light pole with Single Arm Bracket / arrangement for the top mounting fixture as per drawing. 1) 4 way connector and 6A MCB 2) 50 mm diameter DWC pipe for each cable entry. Pipe length is up to 3.5 mtr. Per cable 3) Wiring up to the light fixture from the junction box using 3core x 1.5 sq.mm. flexible copper wires / Fixture of specified make. 4) Concrete coping with foundation bolt with base plate with stiffener. 5) Spiral/Coil Type Earthing from the 8 swg Cu. Wire of 2.5 mtr. With the suitable size pipe with clamps and painting. 6) Radium strip of two color at suitable height & Pole Numbering as per Client / Consultant's instruction 7) Excavation & back filling for erection of poles. Debris to be removed from the site to suitable location as per the instruction of the engineer in charge

Supplying , fabricating and installation of various sizes MS race way / junction boxes/clamps/hangers for Cable Tray, Light Fixture made out ot specified size sheet/Angle/Flat/rod/ channel etc as per design with all necessary accessories like bend, juncation boxes, coupler, Anchor fastner, Bolt Nuts, etc.. & work from MS structure for other work with anchor fastner of Hilti make and necessary hardware with necessary welding has to be done to complete the job from ISA / ISMC / PLATE. The job also includes to paint the structure with two coats of red oxide and two coats color of enamel paint as approved and recommended by consultant. Complete in all respect to be installed at any height with all necessary arrangements. Contractor has to complete the work up to satisfaction of Consultant

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : Stainless Steel AISI-304(18/8) Orissa pattern W.C. pan of size 585x480 mm with flush pipe and integrated type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked black solid plastic seat and lid

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked black solid plastic seat and lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Angle back wash basin size 600x 480 mm with single 15 mm C.P. brass pillar tap

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Angle back wash basin size 400x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Flat back wash basin size 450x 300 mm with single 15 mm C.P. brass pillar tap

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow operated levers

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Surgeon type wash basin of size 660x460 mm with single 15 mm C.P. brass pillar taps with elbow operated levers ISI marked

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : Stainless Steel AISI-304(18/8) Round basin 405x355 mm with single 15 mm C.P. brass pillar tap

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : Stainless Steel AISI-304(18/8) Wash basin 530x345 mm with single 15 mm C.P. brass pillar tap

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required : White glazed fire clay kitchen sink of size 600x450x 250 mm

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 610x510 mm bowl depth 200 mm

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 610x460 mm bowl depth 200 mm

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 470x420 mm bowl depth 178 mm

Providing and fixing white vitreous china water closet squatting pan (Indian type) : Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan.

Extra for using coloured pedestal type W.C pan (European type) with low level cistern of same colour instead of white vitreous china W.C pan and cistern.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White

Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete. 10 litre (full flush) capacity-white

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : White solid plastic seat with lid

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 40 mm dia

Flexible pipe 40 mm dia

Providing and fixing 100 mm sand cast Iron grating for gully trap.

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Circular shape 450 mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357 mm

Providing and fixing toilet paper holder C.P. brass

Providing and fixing soil, waste and vent pipes 100 mm dia Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989

Providing and fixing soil, waste and vent pipes 100 mm dia Centrifugally cast (spun) iron socketed pipe as per IS: 3989

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 100 mm dia pipe

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100 mm dia Sand cast iron S&S as per IS - 3989

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 75 mm dia Sand cast iron S&S as per IS - 3989

Providing and fixing plain bend of required degree. 100 mm dia Sand cast iron S&S as per IS - 3989

Providing and fixing plain bend of required degree. 75 mm dia Sand cast iron S&S as per IS - 3989

Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 100x100x100x100 mm Sand cast iron S&S as per IS - 3989

Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 75x75x75 mm Sand cast iron S&S as per IS - 3989

Providing and fixing double equal plain junction of required degree. 100x100x100x100 mm Sand cast iron S&S as per IS - 3989

Providing and fixing double equal plain junction of required degree. 75x75x75x75 mm Sand cast iron S&S as per IS - 3989

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100x100x100x100 mm Sand cast iron S&S as per IS - 3989

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 75x75x75x75 mm Sand cast iron S&S as per IS - 3989

Providing and fixing single equal plain junction of required degree 100x100x100x100 mm Sand cast iron S&S as per IS - 3989

Providing and fixing single equal plain junction of required degree 75x75x75x75 mm Sand cast iron S&S as per IS - 3989

Providing and fixing double unequal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 100x100x75x75 mm Sand cast iron S&S as per IS - 3989

Providing and fixing single unequal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 100x100x75 mm Sand cast iron S&S as per IS - 3989

Providing and fixing single equal plain invert branch of required degree 100x100x100 mm Sand cast iron S&S as per IS - 3989

75x75x75 mm Sand cast iron S&S as per IS - 3989

Providing and fixing sand cast iron S&S off sets as per IS: 3989 75 mm off sets With 75 mm dia pipe

150 mm off sets With 75 mm dia pipe

150 mm off sets With 100 mm dia pipe

Providing and fixing collar : 100 mm dia Sand cast iron S&S as per IS - 3989

Providing and fixing collar : 75mm dia Sand cast iron S&S as per IS - 3989

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : 50mm dia pipe

Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter : 50mm dia pipe

Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : 100mm dia pipe

Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : 75mm dia pipe

Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : 50mm dia pipe

Providing and fixing vitreous china dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend

Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms

Providing and fixing PTMT Bottle Trap for Wash basin and sink Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2" BSP thread and shapes, weighing not less than 60 gms.

Providing and fixing PTMT urinal cock of approved quality and colou 15 mm nominal bore, 80 mm long, 42 mm high and 30mm wide with BSP female threads weighing not less than 48 gms

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge. Concealed work, including cutting chases and making good the wall etc 1216 (16 mm OD) pipe

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge. Concealed work, including cutting chases and making good the wall etc 1620 (20 mm OD) pipe

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge. Concealed work, including cutting chases and making good the wall etc 2025 (25 mm OD) pipe

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge. Concealed work, including cutting chases and making good the wall etc 2532 (32 mm OD) pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work 15 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work 30 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work 40 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work 50 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work 75 mm nominal outer dia Pipes

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately

BRASS FITTINGS Providing and fixing brass bib cock of approved quality 15 mm nominal bore

Providing and fixing brass stop cock of approved quality : 15 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :80mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 15 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 20 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 25 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) Vertica 25 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) Vertica 32 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) Vertica 40 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) Vertica 50 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) Vertica 80 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 100 mm diameter

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

C.P. BRASS F ITTINGS Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms 15 mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bor 15mm nominal bore

Providing and fixing PTMT grating of approved quality and colour Rectangular type with openable circular lid 150 mm nominal size square 100 mm diameter of the inner hinged round grating

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 200 mm diameter

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 250 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 100 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 150 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 200 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 100 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 150 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 200 mm diameter

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : 150 x 100 mm size P type With Sewer bricks conforming to IS : 4885

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete 100 mm dia. R.C.C. pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete 150 mm dia. R.C.C. pipe

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With Sewer bricks conforming to IS : 4885

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design With 20x20 mm square bar

455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg

500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg

560 mm diameter C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg

Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5 kg

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 100 to 250 mm diameter

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with precast R.C.C. vertical grating complete as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing & fixing of Instant Electrical Operated 5ltr. wall Mounted Hot water Gyser , with all Inlet Out let Connection with stop cock all accessories to complete the item. (spearhot or recold make.)

Providing & fixing of Open Wall Hot & Cold Mixture , with all accessories to complete the item. (Jaquat Cat - CON - With Control Cock Operation Plate.)

Supply, installation, testing and commissioning of Centralized R.O.. system consisting of R.O. membrance, PP cartridge filter, Activated Carbon filter, R.O. multistage booster pump , drain & back wash arrangement & inlet, outlet & overflow & R.O.Water Storage Tank connection etc. as per tech. specification . ( Ion Exchange, Power H2o, Tharmax Make) Input Water Hardness : as per water analysis Output Water Quality : Potable water Capacity : 250 Liters./ hr.

Supply installation, testing and commissioning of dometic water treatment plant comprising of pressure sand filter, multi media, activated carbon filter,softener plant system, chlorination, etc. accrording to input water quality. The scope shall include interconnection piping, valves, Inler Feed Pump Piping,NRV, Valve Control Pannel electrical Internal cabeling wtc, instruments, back wash arrangement, etc. complete ( Ion Exchange, Power H2o, Tharmax Make) Input Water Hardness : as per water analysis Output Water Quality : > 100ppm Capacity: 10,000 Liters./ hr.

Suppying, installing, testing and commissioing of centrifugal submersible monoset pumps with c.i. casing, Bronze impeller, SS Shaft and driven by 415 V AC, 3 phase, 50HZ., motor running at 2900 rpm speed and shall be supplied with all accessories viz., strainer, base plate, coupling, lift hook, chain, starter panel, cabling up to panel, earthing,and delevery pipes & valves etc., complete. Domestic Water Riser :- Capacity :10 cu. mtr./ hr. (1 w. + 1 s.) Head : 30 MTRS

Suppying, installing, testing and commissioing of centrifugal submersible monoset pumps with c.i. casing, Bronze impeller, SS Shaft and driven by 415 V AC, 3 phase, 50HZ., motor running at 2900 rpm speed and shall be supplied with all accessories viz., strainer, base plate, coupling, lift hook, chain, starter panel, cabling up to panel, earthing,and delevery pipes & valves etc., complete. Flushing Water Riser :- Capacity :10 cu. mtr./ hr. (1 w. + 1 s.) Head : 30 MTRS

Supplying, installing, testing and commissioning of centrifugal sump pumps for clear water suitable for 415 ±10% volt, 3 phase/230 ±10% volt single phase, 50 Hz AC power supply. Each pump shall be suitable for automatic/manual operation complete with control panel as required to complete the system for working condition capacity of the pump as under sump location in basement. The pump shall be mounted on top of sump & should be suitable for negative suction of 0.5 - 0.7 mtrs. Domestic Water Supply :- Capacity : 30 cu. mtr./ hr. (1w. + 1 s.) Head : 15 MTRS

Supply installation, testing, commissioning of Bore well submersible pump to be installed in the tube well of required indicated capacity and head as per relevant IS for Bore water lifting with suitable submersible vet type, water cooled, squirrel case motor conforming to IS 9283, working of 3-phase, 50Hz +/- 3% 415 VAT +/- 10%, AC supply 2900 RPM synchronous speed with 10mtr. copper conductor flat cable from pump to starter panel with cables and termination ( all supports clamps pipe fittings mechanical seal, bearing, bush, strainer, etc. comp., Casing C.I., S.S. CF8M impeller, bronze casing, wearing and bearing bush, TC mechanical seal, S.S. bearing, S.S. shaft with sleeve, S.S. strainer, and M.S. morter along with water guard, single phase preventor with all cables of appropriate size control and instrumentations, switches, testing, and installation along with testing. The scope shall also include delivery isolation valve & NRV with PVC piping ( Assume 100mtr depth) ( 10 MTR CU. PER DAY AVG. REQ. with potable water quality)

Providing waste water treatment plant for waste water treatment Packaged Plant on the Aerobic process, the treated effuent to be used for flusing / landscaping. The scope shall include treated waste water tank of @1,00,000 ltr. & all required civil, mechanical, electrical, instrumentation & control system etc. The scope shall also include bypass arrangement with required valves, valve chamber, etc. ( Ion Exchange, Tharmax, Sintex, Niak Enviro,Elctro process Make)Capacity : 75,000 cu. mtr./ day.

Supply, installation, testing & commissioning of localized S.S. Storage water Cooler system with all piping & fitting valves, Prefiltration Aquagurd, U.V. filter with necessary all Fittings, etc complete. (Power H2O, Voltas,Blue Star Make) 80LTR. STORAGE CAPACITY.