REPAIR TO CERTAIN B/R WORKS TO CERTAIN MD ACCN OF PLASSEY LINE AREA UNDER AGE B/R-II AT GE JHANSI

Amount

Demolition of cement concrete incl terrazo flooring (un-reinforced) in ground floor and paving not exceeding 15cm thick (below or above ground level) built in cement mortar, complete all as specified and directed.

M&L for 75 mm thick cement concrete type D2 1:4:8 (using 40 mm graded stone agg) in sub base of flooring/ hard standing complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B1 (20mm graded stone aggregate) in flooring, complete all as specified and directed.

M&L for 75 mm thick cement concrete type C2 1:3:6 (using 40 mm graded stone agg) as in plinth protection and path laid in panels, not more than 3.0 mtr in length, laid to slope 1:30 incl forming joints 10mm wide and duly filled with mastic bitumen (01 part bitumen mixed with 03 parts of sand) surface, complete all as specified and as directed. (Note : The quoted rates are deemed to be inclusive of material against form work and joint fillings.)

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed.

M&L for Non skid ceramic colored tiles , 7 to 8 mm thick (square / rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm as in flooring etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed/ bedding layer in CM (1:6) complete all as specified and as directed.

M&L for ceramic colour tiles in vertical surface of size 350 X 250 x 7/450x300x7 mm thick, jointless type, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with and including 10 mm thick rendering in CM (1:4) for receiving the tiles, complete all as specified and as directed.

M&L for Non-skid colour ceramic tile tiles joint free 8 to 10 mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry over 15 mm thick screed bed or bedding layer in CM 1:6 over brushing neat cement slurry @ 3Kg/sqm etc complete all as speciefied and directed.

All as per item here-in-above but on vertical surfaces such as skirting/dado over and including 10mm thick CM rendering (backing coat) in CM 1:4,complete all as specified and as directed.

Dismantling stone slabs and tiles of any description or thickness laid , bedded and pointed in any mortar as in floors, aprons etc. complete all as specified and directed.

M&L for factory made machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with coloured pigment made of PVC moulded (or rubber mould) with vibrating system, with and including 50mm thick sand cushioning, including in CM (1:3) in edges of pavers, complete all as specified and directed. (Note : The cost of sand cushion and plastering to edges is included in quoted rate.)

M&L for green marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with, over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Dismantling timber scantling 40.0 sqcm and over in section in any position as in framed / unframed works such as roof purlins, rafters, fillets, ridges etc as in roof/ ceiling, complete all as specified and directed.

Dismantling boarding, cupborad any description, fixed in any position including fittings complete all as specified and directed.

M&L for 18/19mm thick particle board, prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

Extra over rates of block board or veneered particle board for external teak wood 18/19mm lipping 6mm thick fixed with nails complete all as specified and directed.

S&F continuous (piano) hinges, mild steel bright finish in electro galvanized width of flat (when open) in 30mm, complete all as specified and directed

S & F drawer/shutter handles, projection drop (50mm to 65mm) on screwed platey complete all as specified and directed

S & F 100 mm aluminium anodise hasp and staple, safety type, aluminium anodised with hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed

Supply & Fix stainless steel magnetic catcher fancy type for kitchen cabinet / drawer complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work built in cement mortar or lime mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L for brick work with old size fly ash bricks, straight or curved on plan exc. 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for half brick thick wall with old size fly ash bricks, straight or curved on plan to any radius built in cement mortar 1:4, complete all as specified and directed.

M&L for 10 mm rendering thick in CM (1:6) on fair faces of brick work/concrete surfaces finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in two coats (1st coat 10 mm thick in CM 1:6 & 2nd coat 5 mm thick in CM 1:4 with WPC) on fair faces of brick work/concrete surfaces, finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed. Note: WPC in 5 mm thick 2nd layer plaster measured and paid separately.

M&L for 5 mm rendering thick in CM (1:3) on fair faces of concrete surfaces in ceiling finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etc including racking out joints hacking for key scrubbing down with water etccomplete all as specified and directed.

M&L for 10 mm rendering thick in CM (1:6) on fair faces of brick work/concrete surfaces finished even & smooth (without using extra cement), complete all as specified and directed.

M&L for rendering 15mm thick in two coats (1st coat 10 mm thick in CM 1:6 & 2nd coat 5 mm thick in CM 1:4 with WPC ) on fair faces of brick work/concrete surfaces, finished even & smooth (without using extra cement), complete all as specified and directed. Notes: WPC in 5 mm thick 2nd layer plaster measured and paid separately.

M&L for preparation of new plastered surface of wall and applying two coat of cement based paint over and incl one coat of exterior grade cement based primer, complete all as specified and directed.

M&L for preparation of new plastered of wall surface and applying two coats of interior acrylic emulsion, over a coat of chalk whitening primer over and incl a layer 3mm thick of wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and as directed.

M&L for preparation of newly plastered surfaces and applying two coats of white wash on ceiling all as specified and directed.

Taking down chowkhats with shutters (without taking off shutters from the frame) area exc 1.5 sqm but not exceeding 4 sqm each including cutting holes in brick/ stone wall built in cement / lime mortar, embedded portion exc half brick but n.exc one brick for inserting new hold fast and making good the disturbed portion/surfaces, in CM 1:3 complete all as directed.

All as per item here-in-above but not exc 1.5 sqm each

Taking down shutters of any description not exc 01 Sqm each, complete all as specified and directed.

Taking down shutters of any description exceeding 01 Sqm and not exc 02 Sqm each, complete all as specified and directed.

M&L for second class hard wood plain, solid, straight chowkhats and frame, wrought framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints and fixing, complete all as specified and directed.

S & F rolled mild steel in Fe 290 Gde-E- 165 as in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sidesand one face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

M&L for 35mm thick 2nd class hard wood glazed & skeleton shutter (fully glazed or gauged) open rebated & prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered sash bar, or rounded, fitted with & mitred beads for securing glass/wiremesh etc, conforming to IS-1003 Part-I & II; size of members of shutters as specified in SSR Part-I section–8, clause 8.24(a) complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

Supply and fixing of powder coated (Min thickness of powder coating 50 micron) anodised aluminium window frame section of door, windows, ventilation, partion wall, cup board with one or more rebates including joinging cleats for fixing etc. complte all as specified.

Providing and fixing powder coated anodised aluminium window shutters, hung/sliding type without sash bars, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading,screws, anodised aluminium fittingssuch as peg stays 150 mm long (1 No.) hinges type B-21 100 mm long (2 nos.) suitable handle (1 no.) etc all as specified and directed .

S & F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

M&L for preparation of new steel or iron surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed

M&L for powder coated ( minimum thickness of powder coating not less than 50 micron) aluminium ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, 5.5 mm thick figured glass, rubber packing, powder coated aluminium snap beading, screws etc, complete all as directed.

M&L for preparing new or previously untreated surfaces of wood or wood based materials of any description not otherwise described exc 10 cm width or girth and applying two coat of synthetic enamel paint over and including a coat of pink primer and layer of putty/filling material to get smooth & level finish, complete all as specified and directed.

S&F of aluminium alloy anodized sliding door bolt 300mm (aldrop bolt) length with hasp staple and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all specified and directed

S&F of 125 mm Butt hinges, heavy weight, cold rolled mild steel, and fixed complete all specified and directed

S&F of 100 mm size butt hinges, extruded aluminum alloy with galvanized mild steel pin type B-21 anodized complete all specified and directed

S&F of 150mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F of 150mm aluminum handle cast type anodized complete all specified and directed.

S&F of mild steel ordinary rat tail rod pattern springs of size 300mm including roller and roller plate complete all as specified and directed

S&F of 140 mm door stopper of aluminium body and tongue anodized with hard drawn steel spring fixed in floor complete all as specified and directed.

S&F in repair Rubber bush (door seal) of 25mm wide fixed to door complete all as specified and directed

M&L for cement concrete 1:2:4 type B1 (20mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, copings, bond stones, bed plates for hold fast and the like including weathering, slightly rounded or chamfered angles and throating, , complete all as specified and directed.

M&L for mild steel angles, bars, flats etc, as in hold fasts, pipe clamps, plain angle cleats for securing purlins, supports for stiffening of fencing, wall ties and similar small articles confirming to Fe-290 Gde E-165, complete all as specified and directed.

S&F of stainless steel wire cloth 0.56 mm in nominal dia of wire average width of aperture 1.18 mm and fixed with tinned tacks of stainless steel wire staples to steel shutters or fixed with wooden beads to wooden joinery, complete all as specified and directed.

S&F of 3 mm thick sheet glass ordinary quality and glazing type, not exc 0.50 sqm in each pane, duly fixed with oil putty or wooden bidding as required, including hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F of 3 mm thick sheet figured glass pin headed type, not exc 0.50 sqm in each pane, duly fixed with oil putty or wooden bidding as required, including hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F in replacement of stainless steel wire cloth 0.56 mm in nominal dia of wire average width of aperture 1.18 mm and fixed with tinned tacks of stainless steel wire staples to steel shutters or fixed with wooden beads to wooden joinery, complete all as specified and directed.

S & F in repair stainless steel curtain rod 25mm dia steel pipe cutting into length as required at site with and incl SS end caps/lobs and SS wall mounting brackets, complete all as specified and directed.

S&F of ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of Ringfit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC(SWR) vent cowl 110mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC floor trap of 75 mm outlet, jointing to waste pipe, complete all as specified and directed.

S & F 15 mm bore Galvanized Steel tubes, medium grade fixed to walls and ceilings or laid in floors, concealed or open incl cutting of grooves including taking up or down with connections and fittings all as specified and directed

S & F 20 mm bore Galvanized Steel tubes, medium grade fixed to walls and ceilings or laid in floors, concealed or open incl cutting of grooves including taking up or down with connections and fittings all as specified and directed

Supplying and laying of 16 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/wall including taking up or down with connections and fittings complete all as specified and directed.

Supplying and laying of 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches /wall including taking up or down with connections and fittings complete all as specified and directed.

M&L for cutting chases, pinning in for concealed water tubing, not exc 10 cm girth and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc complete all as specified and directed.

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered white colour 500 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, with and incl disconnecting and dismantling the existing un-serviceable PVC/RCC water tank on top of roof/slab of bldgs, complete all as specified and directed.

S&F of 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S&F of 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms) etc, complete all as directed.

S&F in repair 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms) etc,complete all as specified and directed.

S&F in replacement of stainless steel sink, 1.00 mm thick for kitchen with plug, with and incl 40mm dia CP waste coupling, waste pipe of 750mm long, washers, cantilever brackets, connecting union etc overall approx size 495 mm x 420 mm with approx bowl size of 410 mm x 330 mm x 160 mm etc, complete all as specified and directed.

S&F in replacement of stainless steel kitchen plate rack made out of 1 mm thick sheet of size 765x920mm and 220mm deep, weight not less than 7 Kg, complete all as specified and as directed.

S&F in replacement of pillar taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, complete all specified and directed.

S&F in replacement of stop cock with long shank and cup (concealed type), 15mm dia with wall flange, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe / unions, complete all as specified and directed.

S&F in replacement of overhead shower of dia 125 mm round shape single flow, ABS body chrome plated fancy type, with and incl swivel type shower arm of 20mm dia with wall flange made of cast copper alloy, chromium plated fancy type, complete all specified and directed.

S&F in replacement of long body bib cock, 15 mm dia with wall flange made of cast copper alloy, chromium plated, complete all specified and directed.

S&F in replacement of angular stop cock 15 mm dia with wall flange made of cast copper alloy, chromium plated type, complete all specified and directed.

S&F in repair SS grating of squre/round shape, overall size of 150x150mm with hinge type openable jali of 100 mm dia size with and incl fixing with CM to floor/nahani traps etc, complete all specified and directed.

S&F in replacement of towel rail 600 mm long D type between flange and wall bracket made of cast copper alloy, chromium plated, complete all specified and directed.

S&F in replacement of PVC multipurpose cabinet mirror with front openable door of overall size 350 x 450 mm, complete all as specified and directed.

S&F in replacement of Brass CP connection 15mm dia and 45cm long with 2 Nos brass check nuts with washers for geyser, complete all as directed.

S&F in replacement of PVC waste pipe 32 mm dia 750 mm long with for wash hand basin or for kitchen sink, complete all as specified and directed.

S&F in replacement of waste coupling, chromium plated (half or full threaded), 32 mm dia size, complete all as directed.

S&F in replacement of waste coupling, chromium plated (half or full threaded), 40 mm dia size, for kitchen sink complete all as directed.

S&F in replacement of PVC connection 450 x 15mm dia PTMT (PVC), complete all as directed.

S&F in replacement of 10 ltr capacity PVC valve less symphonic action type flushing cistern, white, with inlet ball valve, float and handle with and including wall bracket, 32 mm dia PVC flush pipe and connected to squat pattern / pedestal pattern water closet, including all joints and making good to the wall & floor,complete all specified and directed.

S&F in replacement of 1st quality vitreous china squatting pan Orissa pattern of size 580x440 mm, white colour with integral foot rests water closet including flush pipe, P Trap and connecting cone but exluding flushing cistern, duly fixed in lime concrete bedding and making good of floor surface, complete all as directed.

S&F in replacement of 1st quality vitreous china ware European type WC with "P" or "S" type traps and same make plastic seat cover of white colour including flush pipe, fixing bolts etc and making good of the wall & floor surface, complete all as directed.

S&F in replacement of 1st quality vitreous china wash hand basin, white flat/angle back, size 550x400mm, complete including necessary cutting for and pinning in ends of brackets) with and including wall brackets, PVC waste pipe of 750mm long, CP waste coupling of 32mm dia size, complete all as specified and directed.

Demolition of cement concrete of any description and in any position of WC’s/Bathroom etc in sunken portion area above ground floor, removing demolished material completely and old waste pipe from sunken portion and cleaning the side/bottom surface of sunken floor with wire brush, complete all as specified and directed.

M&L PCC 1:5:10 Type E2 using 40mm graded stone aggregate as in mass filling in two layer in sunken portion complete all as spd and directed

M&L for 25 mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in padding levelling etc and roof kerbs with liquid water proofing solution finished even and fair with proper slope as prepatory works to water proofing treatment complete all as spd and directed by EIC. Note:-liquid water proofing solution shall be provided in 150ml in 50 Kg of Cement by weight and cost of liquid water proofing solutionmeasured and paid seperate item complete all as directed.

M&L for 15mm thick plastering in CM 1:3 along the wall of toilet and bath mixed with 3 % WPC and finished even and smooth without using extra cement complete all as specified and directed.

M&L for bitumen blown 80/100 grade applied hot, two coats to plastered surfaces of any description at the rate of 1.5 kg per sqm per coat complete all as specified and directed.

M&L for Polythene film black 50 micron laid in floor complete all as specified and directed.

M&L for 50mm dia G.I pipe as in spout to drain out if any leakage occures in the sunken portion complete all as spd

Supply only integral liquid water proofing compound LW++, mixed in CM as per manufacturer instruction, complete all as specified and directed.

M/sDaljeet singh keer (BID ID -3336343)

M/S Kesav Dev Agarwal (BID ID -3336651)

ADARSH ENTERPRISES (BID ID -3335515)

M/s Jagdish Chandra Arora (BID ID -3335929)

VIJAY BUILDERS (BID ID -3336630)

m/s ramesh saran agarwal (BID ID -3336220)

M/S Kharya Associates (BID ID -3336341)

HARNAM SINGH ANIL SINGH (BID ID -3336809)

FTH TRADERS (BID ID -3336282)

M/S Kumar Contractors (BID ID -3336540)

M/S NASIM AND CO. (BID ID -3335692)