ADDN ALTN OF CERTAIN OTM ACCN AT MHOW

Amount

SCHEDULE "A" :

Item No. 01 :- Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, etc or for shafts, wells, cesspits, manholes pier hold etc n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in any type of soil, complete all as specified and directed.

Item No. 02 :-Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs/ blankets any thickness including cover fillets complete all as specified and directed.

Item No. 03:- M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate complete all as specified and directed.

Item No. 04 :- Supply and laying DWC HDPE pipes SN8 150 mm, internal dia confirming to IS 16098 Part-II laid and jointed complete all as specified and directed.

Item No. 05 :- Dismantling of AC sheet (corrugated or semi corrugated etc) including AC ridges as in roof covering complete. Note:- Opening of existing wind tie where required for taking down of AC sheet is included in the rate quoted against this item, complete all as specified.

Item No. 06 :- S & F Pre-painted galvalume aluminium zinc GI based profile pattern steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, 150 Gsm as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed by Engineer- in Charge.

Item No. 07 :- S & F Pre-painted galvalume aluminium zinc coating GI based profile pattern steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, 150 Gsm as in ridge covering/cladding to wall, fixed with self tapping screws as specified and directed by Engineer- in Charge.

Item No. 08 :- S&F for MS hollow tube rectangular / square in section and used for trusses, purlins and rafter etc as structure member complete

Item No. 09 :- M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all specified.

Item No. 10 :- Providing and fixing false ceiling at any heights with integral identified calcium silicate reinforced with fibre and natural filler false ceiling tiles of size 595 x 595 mm of approved texture, design and patterns pinhole 8mm thick semi perforated square edge tile having NRC (Noise Reduction coefficient) of 0.50 (minimum) Light reflectance of 85% (minimum). Non combustible as per BS: 476 (PART-4), fire performance as per BS : 476(PART 6 & 7 ), humidity resistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on interlocking metal powder coated T-Grid of hot dipped galvanized iron section on Silhouetter profile, rotary stitched double webbed white with 1 mm reveal profile (White/black), comprising of main-T runner of size 15 x 32mm of length 3000m, cross - T of size 15 x 32 mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of size 600 x 600 mm, from ceiling using galvanized mild steel item, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod and L-shape level adjuster of size 85x25x2 mm. Galvanized iron perimeter wall angle of size 19 x 19mm of length 3000 mm to be fixed on periphery wall /partition with the help of plastic rawl plugs at 450mm centre to centre and 40mm long dry wall S.S. screws. The work shall carried out as per specifications, drawing and as per directions of the Engineer-in-Charge .

Item No. 11 :- M&L cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in roof kerb mud stop etc complete all as specified and directed.

Item No. 12 :- Demolition of brick work built in CM incl all quarries arches and pillar etc complete all as specified.

Item No. 13 :- Dismantling water tanks of any description, capacity exc 500 and not exc 1000 litres and removing from site complete all as specified and directed.

Item No 14 :- Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the permises complete all as specified and directed.

Item No. 15 :- Demolition of kota stone/ stone in floor laid, bedded and pointed in any mortarcomplete all as specified and directed.

Item No. 16 :- M&L Prepolished (mirror finish) Machine cut kota stone slab flooring 22-25 mm thick as flooring, over & including 20 mm thick screed bed in cement mortar 1:6 laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing & rounding to edges complete all as specified.(Kota stone should be single piece in tread and riser).

Item No. 17 :- M&L Prepolished (mirror finish) Machine cut kota stone slab flooring 20-25 mm thick as in riser, steps & skirting over & including 15 mm thick rendering in cement mortar 1:4 laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing & rounding to edges complete all as specified and direct (Kota stone should be single piece in tread and riser).

Item No 18 : - BLANK

Item No 19 :.Taking down cement plaster any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

Item No. 20 :- M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick or concrete surface of walls and finished the surfaces even & fair without using extra cement complete all as specified and directed.

Item No 21 : - M&L for rendering 15 mm thick in cement mortar 1:4 in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, both the coats (1st layer and 2nd layer) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finished the surfaces even and fair without using extra cement of approved makes complete all as specified and directed.

Item No. 22:- M&L for preparation of new plastered surfaces and applying three coats of white wash on wall on newly plastered / concrete surfaces, complete all as specified and directed.

Item No. 23 :- M&L Brick work using fly ash bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

Item No 24 - Supply only liquid water proofing compound, ISI marked omplete all as specified and directed.

Item No. 25:- M&L for preparation of new surfaces of wall and applying acrylic distempering in two or more coats over a coat of alkali resistance priming paint, 1st quality acrylic distemper(ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, required shade and colour, complete as per manufacturer's specification.

Item No. 26 :- M&L for applying 1.5 mm thick (average in two coats) birla / Jk Putty in two layers on new or old wall surfaces including preparaton of surfsces with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete all as specified and directed.

Item No. 27:- Providing precast cement concrete 1:1.5:3 type A0 (12.5mm graded aggregate) jallies, 40mm thick, including all molding and set in CM 1:4 complete all as specified.

Item No 28 : - M&L for RCC (nominal mix) 1:1.5:3 type A1 using 20 mm graded stone aggregate as in beam, cantilevers, bressummers, lintels over 1.5 m span and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

Item No. 29 :- M&L Form work to sides and soffits of floor or roof beam, beam hauchings, girders, bressummers, lintels, cantilevers, shelves, for curved rough finished concrete surfaces complete all as specified and directed.

Item No. 30 :- S&F Mild Steel TMT bar 10 mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Item No. 31 :- M&L for Mild Steel TMT bar 8 mm dia cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Item No. 32 :- M&L for Mild Steel round bar 8 mm dia cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Item No. 33 :- M&L for Precast cement concrete 1:1.5:3 type A1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in CM 1:4 complete all as specified and directed.

Item No. 34 :- S&F GI tubes medium grade with all fittings fixed to walls and ceilings or laid in floors of 15 mm bore of pipe complete all as specified and directed.

Item No. 35 :- S&F GI tubes medium grade with all fittings fixed to walls and ceilings or laid in floors of 20 mm bore of pipe complete all as specified and directed.

Item No. 36 :- S&F GI tubes medium grade with all fittings fixed to walls and ceilings or laid in floors of 25 mm bore of pipe complete all as specified and directed.

Item No. 37 :- Taking up or down steel tubing and connections including cleaning if refixing required for 15 mm bore of pipe complete all as specified and directed.

Item No. 38 :- Taking up or down steel tubing and connections including cleaning if refixing required for 20 mm bore of pipe complete all as specified and directed.

Item No. 39 :- Taking up or down steel tubing and connections including cleaning if refixing required for 25 mm bore of pipe complete all as specified and directed.

Item No. 40 :- S&F in repair coloured vitreous china wash down water closet pan (pedestal pattern) with S or P trap including connection of flushing cistern, seat cover, brackets, flush pipe etc, fixed in repairs complete all as specified & directed by Engineer-in-Charge.

Item No. 41 :- S&F in repair vitreous china wash down water closet pan (pedestal pattern) with S or P trap cacade type of size 365 x 660 x 770 mm coloured with cistern (with twin flush fittings) complete including seat cover and fixing of flushing cistern, brackets, flushing pipe etc, fixed in repairs, of approved makes complete all as specified and directed by Engineer - in - charge.

Item No. 42 :- S&F in repair vitreous china WHB size 550x400 mm white flat back Including CP waste coupling and PVC wash pipe but excluding taps, waste, chain & plug & porcelain stopper but including brackets with two coats of synthetic enamel painting over a coat of red oxide primer etc. complete all as specified and directed by Engineer - in - charge.

Item No. 43 :- S&F Plastic water closet seat cover white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

Item No. 44 :- S&F in repairs 15 mm dia pillar tap cast coper alloy fancy type with capstan heads chromium plated screwed down high pressure with or without letered "Hot or Cold" pressure with long screwed shanks & fly nuts screwed for iron pipe etc. complete all as specified and as directed.

Item No. 45 :- S&F in repair bib tap 15 mm bore, chromium plated, fancy type long shank with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

Item No. 46 :- S&F in repair PVC connection 15mm dia size and 450 mm long with 2 Nos check nuts its washers complete all as specified and directed. Make: Prayag

Item No. 47 :- S&F in repair of stainless steel wall mount soap holder / brush holder of standard size and shape of approved makes complete all as specified and as directed.

Item No. 48 :- S& F in repair CP brass tubular towel rail 20 mm dia D type 60 cm long between flanges complete all as specified and as directed.

Item No. 49 :- S&F in repairs sheet glass shelf 5.5mm thick with aluminium bracket and railing 60cm long and width 12.5cm as per sample complete all as specified..

Item No. 51 :- S&F in repairs mild steel chromium plated grating (round)125mm dia fixed over floor/Nahani trap complete all as specified.

Item No. 52 :- S&F in repairs chromium plated brass stop cock fancy type screwed both ends high pressure for 15mm bore size iron pipe or ferrule concealed type long body , complete all as specified.

Item No. 53 :- S&F chromium plated Jet for EWC with 1.00 Mtr long PVC pipe including neck essay GI fitting as required like toe, nipple etc all as specified and directed .

Item No. 54:- S&F in repairs CP brass shower rose with survival joint 125 mm size suitable for 15mm bore pipe complete all as specified and directed.

Item No. 55:- S&F in repairs 32mm bore and 60cm long PVC flexible waste pipe for WHB complete all as specified.

Item No. 56 :- S & F in repairs 15 mm bore Angle Stop valves one way, brass chromium plated, fancy type, fixed to iron pipe or for unions complete all as specified and directed.

Item No. 57 :- Cutting into existing manholes for connecting new drain pipes of internal dia of pipe150mm, making good to pipe and rendering ,cutting out existing benching for and forming branch channeling cement concrete 1:2:4 type B1 smooth finished and reforming benching.

Item No. 58- M&L for MS framed brackets of angles or tees with web and flanges cut to shape., drilled and countersunk for screw, including bending and welding, conforming to Fe-290Gde-E-165, complete all as specified and directed.

Item No. 59 :- M&L returning, filling in soft/loose soil including, spreading, leveling, watering and well ramming in layers not exc 25cmcomplete all as specified and directed.

Item No. 60 :- Removing excavated material (soil) to a distance exc 250 m and not. exc. 500 mtr and depositing where directed at a level nexc 1.5 mtr above the starting point.

Item No. 61 :- Demolition of cement concrete in ground floor or paving not exc 15 cm thick(below or above Ground Level) complete all as specified and directed.

Item No. 62 :- Demolition of cement concrete in above ground floor exc 15 cm thick complete all as specified and directed.

Item No. 63 :- M&L for hardcore of gauge n.exc.63mm of broken stone,deposited,spread and leveled in in layers n.exc 15cm thick,watered and rammed to a true surface complete all as specified and directed.

Item No. 64 :- M & L 50 mm thick PCC 1:3:6 type C-1 using 20 mm graded aggregate as in plinth protection finish even & fair without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling compreising of one part of heated bitumen 80/100 gde and three part of sand (all by weight) complete all as specified and directed.

Item No. 65 :- Surface dressing not exceeding 15 cm deep in soft / loose soil including removing of surplus soil to a distance n. exc 50M and making good complete all as specified and directed

Item No 66 - Taking down chowkats or frames with shutters not exc 1.5 Sqm each (with out taking off shutters from the frames) incl making good the disturbed portion complete all as specified and directed.

Item No 67 :- Taking down chowkats or frames exc 1.5 sqm but not exc 4.0 Sqm each with shutters ( with out taking off shutters from the frames) incl making good the disturbed portion complete all as specified and directed.

Item No 68 : S & F for solid PVC door frame of size 50x47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening and complete all as specified and directed

Item No 69 : - BLANK

Item No. 70 :- M&L Second class hard wood (Sal) plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

Item No 71 : - S&F 35 mm thick second class hard wood rail and style plain framed factory made panelled shutter (two panel) with lock rail and panel of 9 mm BWP commerical ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Item No. 72:- M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, Fe 290-W(GdeE- 165) quality, complete all as specified and directed.

Item No 73 :- S&F mild steel flat iron as in bands straps, supports or stays for rainwater, ventilating pipes including bolt if required, hooks (stay) heavy for large gates,hook and pintle hinges,large hasps and staples, hold fasts, wall ties, hooks for hanging fans , cleats for securing purlins to wood trusses or rafters and similar small articles conforming to Fe -290 Gde E-165 complete all as specified and directed.

Item No 74 :- M&L for preparation of surfaces of wood and wood based materials, steel and iron work, new or old, of any description, treated with tar or coal tar black paint to treating ends of posts, backs of chowkats etc area tarred not exc 0.1 Sqm each complete all as specified and directed.

Item No. 75 :- M&L for PCC (1:2:4) type B 0 using 12.5 mm graded stone aggregate as in filling of hold fast and steel door frame or chamfered on edges complete all as specified and directed.

Item No. 76 :- M&L for preparation of surface of wood and wood based materials new or old of any description and girth not other wise described and treated with creosote complete all as specified and directed.

Item No. 77 :- M&L Second class hard wood 35 mm thick factory made glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc, divided into square,with plain, chamfered or rounded,mitered and rebated sash bars,any number, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR part I section 8 clause 8.20 (a) complete all as specified and directed.

Item No 78 : - BLANK

Item No. 79 :- S&F Butt hinges, medium weight, cold rolled mild steel 100 mm long complete all as specified and directed.

Item No 80 & 81 : - BLANK

Item No. 82 :- S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 140 mm complete all as specified and directed.

Item No. 83 :- S&F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Item No. 84 :- S&F Decorative stainless steel curtain rods 25 dia with decoratie head on both end of rod and necessary clamps / fixing brackets, stops, rollers etc complete all as specified and as directed.

Item No. 85 :- M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Item No. 86 :- S&F 6mm thick MS plates (plain or chequered) channels, square cut, forming holes with riveted, bolted or welded attachment complete all as specified and as directed.

Item No. 87 :- S&F galvanised stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

Item No. 88 :- S&F machine pressed precast concrete interlocking paver block any shape size and colour confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed. (Shape, size & colour shall be as approved by GE).

Item No. 89 :- M & L for sand cushioning for Machine pressed precast concrete interlocking paver block including watering and consolidation complete all as specified and directed.

Item No. 90 :- M&L for applying two coats of synthetic enamel paint on old steel surfaces of any description, not otherwise described over 10cm width or girth, including preparation of old steel surfaces.

Item No. 91 :- M&L for providing 1:2:4 type B1 as in cills, seismic and other similar bands plinth courses, coping, bed plates, bond stones etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form complete. drains , coppings& surface channels complete all as specified and directed. Coping of wall including necessary use of formwork and set in cement mortar 1:4

Item No 92 :- M & L for repair to sunken floor by provide water proofing treatment to sunken floor surfaces of RCC slab by the following specifications as specified and directed :-(a) Demolition of old sunken surfaces complete and cleaniong of all loose particles and apply cement slurry @3.00 kg / sqm on old surfaces by brushing. (b) Provide PCC 1: 1.5:3 type A with using 12.5mm graded stone aggregate in slope of average thickness 50mm on sunken floor slab mixed with and including integral water proofing compound manufactured by Dr FIXIT or equivalent as approved, finish the surface even & smooth without using extra cement. (c) Rendering 15mm thick in CM 1:3 mixed with & including integral water proofing compound on sunken floor and sides of (Vertical surface) sunken portion. (d) Applying surfaces of bituminous primer (conforming to IS-3384-1965) @0.40 Kg/Sqm complete. On complete sunken surfaces of floor & wall and provide necessary connections to soil/waste pipe from WC/ nahani trap etc including demolition of old sunken complete all as specified and as directed (e) After laying of all sewage/plumbing pipes with fixtures in position, apply two coats of polymeric based chemical as per manufactures instructions over bottom and sudes of sunken portion upto 600 mm height.

(f) APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with plyester non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed. (g) Fill the sunken floor with PCC 1:5:10 type E-2 using brick aggregate. (h) Fixing of 50 mm dia CPVC pipe projecting 450 mm clear of face outer wall shall be provided to drain out seepage water if any. (j) Testing of sunken as per specification mentioned in SSR part-I/ P.S. (NOTE : Floor Area shall be measured for payment).

Item No. 93 :-M & L for provide CPVC spout pipe of 50 mm bore & 45cm length in sunken floor including cutting holes in brick walls built in cement mortar and making good the dismantled portion in PCC (1:2:4), type B1 with using 20mm graded stone aggregate with wall finish at the disturbed portion of external surfaces complete as directed and specified.

Item No. 94 :- M & L for cutting holes in brick walls built in cement mortar at the starting point of down take soil/waste pipe at any floor, fill the joint of down take pipe & trap with thick mortar in CM 1:3 and making good the dismantled portion in PCC (1:2:4), type B1 with using 20mm graded stone aggregate with wall finish at the disturbed portion of external surfaces complete as directed and specified.

Item No 95 : - BLANK

Item No. 95 :- Plain cement concrete 1:5:10 mix, type E-2 (using 40mm graded Brick aggregate) as in filling of sunken portion complete all as specified and directed.

Item No. 96 :- M&L 40mm thick PCC 1:2:4 type B-1, (20mm graded aggregate), as in bases of floors even complete all as specified and directed.

Item No. 97 :- M&L Cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete as directed and specified.

Item No. 98 :- M&L for joint free non skid ceramic joint free (coloured tiles) 7 to 8 mm thick square/ rectangular area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm ect set and jointed in neat cement slurry and pointed in white or coloured cement to match and screed 15 mm thick in cement mortar 1:4 complete all as directed and specified.

Item No. 99 :- M&L for Brickwork with flyash bricks with using Modular size Brick, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as directed and specified.

Item No. 100 :- M&L grinding & wax polishing to mirror finish to old kota stone slab flooring & steps, mixed with pigment to match the shade of slab complete all as specified and directed.

Item No. 101 :- M&L Rendering 5mm thick in cement mortar 1:3 as on concrete surfaces in ceiling finished even and smooth without using extra cement including taking down cement plaster on walls built in cement mortar etc all as directed and specified.

Item No. 102 :- S & F in repairs PVC (SWR) Floor trap/Nahani trap plain or multi with stainless steel grating incl joining to waste pipe with solvent cement joint dia of outlet 75 mm bore complete all as specified and directed.

Item No. 103 :- S & F in repairs 110 mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to walls or floor or in trench complete all as specified and directed.

Item No. 104 :- S & F 110 mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to walls or floor or in trench complete all as specified and directed.

Item No. 105 :- S & F in repair 110 mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed.

Item No. 106 :- S & F in repair 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

Item No. 107 :- S & F in repair 75mm bore PVC (SWR) vent cowl complete all as specified and directed.

Item No. 108 :- S & F in repair 110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

Item No. 109 :- S & F in repair 110 mm bore PVC (SWR) bend with access door complete all as specified and directed.

Item No. 110 :- S & F in repairs 75 mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to walls or floor or in trench complete all as specified and directed.

Item No. 111 :- S & F 75 mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to walls or floor or in trench complete all as specified and directed.

Item No. 112 :- S & F in repair 75 mm bore PVC (SWR) bend any radius complete all as specified and directed.

Item No. 113 :- S & F in repair 75 mm bore PVC (SWR) bend with access door complete all as specified and directed.

Item No. 114 :- S & F in repair 75 mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed.

Item No 115 : - BLANK

Item No. 116 :- S&F in repair Vitreous china squatting pan of Orissa pattern size 580 x 440 white with P trap long size) joint run and front or back inlet with integral footrest including connection to trap and to flushing pipe,anti-syphonage pipe, etc, fixed in repair complete and making good to floor in CM 1:3 all as directed and specified.

Item No. 117 :- S&F in repair Vitreous China urinal bowl, half stall coloured, with CP urinal spreader for fixing with 15 mm dia pipe. type union for discharge pipe, PVC waste pipe 32mm bore, providing and fixing plugs, bedding urinals against the wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long steel screws, pointing around the urinal back in cement, complete all as specified and directed.

Item No. 118 :- S&F in repair Waste coupling of 40 mm dia PTMT (half or full threaded) . (Minimum weight 32mm-45gms/40mm-60 gms) fixed in repair complete all as specified and directed.

Item No. 119 :- S&F in repair Rotational moulded polyethylene water storage tanks Capacity 2000 ltr (cylindrical vertical with closed top) hoisted and incl 25 mm bore PTMT Nipple and ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass suitable for HDPE water tank. (Minimum weight 15 mm-38gms/20mm- 45gms /25mm- 65gms) and dismantling of old water tanks and removing to store complete all as specified and directed.

Item No. 120 :- Taking down shutters of any description exc 1.00 sqm but n exc 2.00 Sqm each and removing to or from store.

Item No. 121- M&L Pressed steel frames for doors with one with one or more rebates size of frame (105 x 60 mm ) including necessary fixing lugs, hinges, lock strike plate, etc.,complete all as directed and specified.

Item No. 122 :- S&F Butt Hinges, extruded Stainless seteel with galvanised mild steel hinge pin, anodized and fixed, type B-21, 100mm size complete all as directed and specified.

Item No 123 : S&F Extruded aluminium alloy handles fabricated type anodized 150mm size complete all as directed and specified.

Item No. 124 - S&F 150mm long aluminum anodized barrel tower bolt of extended section complete all as directed and specified.

Item No 125 : - BLANK

Item No. 126 :- M & L Preparation of old decorated surfaces of wall & ceiling by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and trading oil and greasy spots from plastered or unflustered surfaces including cornices, pilasters etc and apply two coat of white wash complete all as specified and directed.

Item No. 127 :- S&F 1mm thick Plain, galvanised, mild steel sheeting drilling and fixing with necessary screw, in construction joint, etc (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed.

Item No. 128 :- Preparation of old wood or wood based surfaces of any description exc 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Item No. 129 :- S&F in repairs steel window with side hung shutter including projecting type hinges with steel handle, peg stay complete with glazing bars dovetailed or welded, etc complete all as specified and as directed.

Item No 130, 131 & 132 : - BLANK

Item No. 133 :- M&L for PCC1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor, etc complete all as specified and directed

Item No. 134 :- M & L PCC 1:2:4 type B-2 using 40 mm graded stone aggregate as in foundation, sub base/ mass concrete etc. complete.

Item No. 135 :- M&L for glazed ceramic coloured tiles of size not less than 300x450/300x600 and 7 to 8mm thick as on vertical surfaces such as wall, dado, skirting etc set and jointed in neat cement slurry and pointed with coloured cement to match over 10 mm thick backing coat on fair faces of brick work in CM (1:4) complete all as specified and as directed.

Item No. 136 :- M&L for chequered cement concrete tiles with grey cement and pigment of size 20cmX20cmX25mm thick ,set and jointed and pointed in neat cement slurry in floor etc over and including 20 mm thick screed bed in CM 1:4 complete all as specified and directed.

Item No. 137 :- Rounding to edges of stone slab slab one edge such as in steps, cooking platform, and other similar situation complete all as specified and directed.

Item No. 138 :- S & F for precast cement concrete type B-1 (1:2:4)(20mm graded stone aggregate ) as in kerb and edging to road and foot path, etc including chamfered, weathering, throating etc and setting in CM (1:4) complete all as specified and as directed.

Item No. 139 :- Cutting holes into or through cement concrete slabs, chajjas, etc. reinforced or otherwise N exc 100 sqcm

Item No. 140 :- Cutting channels, grooves or rebates n exc 15cm girth, and trimming surface With or with reinforce out all as specified and directed.

Item No. 142 :- Dismantling of cast iron pipes jointed in cement mortar 100 / 75 mm bore all as specified and directed

Item No. 143 :- Dismantling of PVC pipes jointed in cement mortar 110 / 75 mm bore all as specified and directed

Item No. 144 :- S&F 75mm PVC reducers PVC (SWR) complete all as specified and as directed.

Item No. 145 :- S&F 110 mm PVC reducers PVC (SWR) complete all as specified and as directed.

Item No. 146 :- S& F as in repair 40mm Bottle trap of PTMT having minimum water seal of 25mm .(Minimum weight 32mm-260gms/ 40mm-270 gms) complete all as specified and directed.

Item No. 147 :- S& F as in repair 40mm High density polyethylene (HDPE) pipes of pressure rating 6 kgf/sq. cm all as specified and directed.

Item No. 148 :- S&F in repair of 20mm bore ball valve high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball screwed for iron pipes and fixed. ( Min Weight 20mm-210 gms) complete all as specified and as directed

Item No. 149 :- M&L in for Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming IS-1161-1979 grade ST-240 complete all as specified and as directed.

Item No. 150 :- Demolition of reinforced cement concrete of any description and in any position not otherwise described complete all as specified and directed.

Item No. 151 :- M&L RCC type B-1 1:2:4 using 20mm graded stone aggregate as in kitchen shelves , manhole cover, etc including dismantling of existing RCC work complete all as specified and directed.

Item No. 152 :- M&L form work to suspended slab as in kitchen shelves etc.complete all as specified and as directed

Item No 153 : - BLANK

Item No. 154 :- Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, etc or for shafts, wells, cesspits, manholes pier hold etc n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in Hard/Dense soil, complete all as specified and directed.

Item No. 155 :- Removing excavated material (soil) to a distance not. exc. 50 mtr and depositing where directed at a level nexc 1.5 mtr above the starting point.

Item No 156 : M&L for preparation of new plastered and apply two coat of cement base paint over a coat of primer(same make) on walls complete all as specified and directed by Engr-in-Charge.

Item No. 157 - M&L for scratch free, double charged, vitrified ceramic tiles 9 to 10 mm thick (square or rectangular) area of each tile not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20 mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

Item No. 158 :- All as per item No 157 above but as in skirting/ dado etc with and including 10mm thick backing coat in cement mortar 1:4 an wall complete all as specified and as directed.

Item No. 159 :- M & L for Brushing with neat cement slurry @ 3 Kg per Sqm area mixed with integral water proofing compound as specified and directed (WPC shall be measured and paid separately under respective item).

Item No 160, 161, 162 & 163 : - BLANK

Item No. 164 :- M&L for applying two coats of bitumen based aluminium painting @ 0.15 Kg / sqm each coat on water proofing treatment with preparation of surface as on non assessable area complete all as specified and directed.

Item No. 165 :- S&F in repair fancy type chromium plated 15mm bore two way Bib cock cast copper alloy with crutch or butterfly handle, screwed for iron pipe or brass ferrule etc complete all as specified and as directed.

Item No. 166 :- S&F in repair chromium plated brass wall mixer 3-in-1 fancy type with provision for both hand shower and overhead shower complete with wall flange (excluding hand & over head Shower) screwed down for 15 mm GI bore pipe complete all as specified and directed.

Item No. 167 :- S&F in repair health faucet with flexible pipe of one mtr length including wall hook for EWC complete all as specified and as directed.

Item No. 168 :- S & F in repairs vitreous china wash basin white (oval shaped under counter) of size 550 x 400mm including 32mm brass CP waste coupling complete all as specified and as directed .

Item No. 169 :- S&F in repair kitchen sink with drainage board made of stainless steel 1.0 mm thick in kitchen with plug , washer and waste including bedding layer in CM (1:6) in wall or including fixing cantilever bracket and connecting union to pipes over all size 915x460 mm bowl size 410x330x160 mm including taking out unserviceable kitchen sink complete all as specified and as directed.

Item No 170, 171 & 172 : - BLANK

Item No. 173 : S & F in repair of flush pipe of polyethylene of low or high density or PVC, 32mm dia for low level flushing cistern/basins complete as complete all as specified and directed.

Item No 174 : - BLANK

Item No. 174 : S & F in repair of LDPE pipe 32mm bore fixed to wall/ceiling with bends/elbow complete all as specified.

Item No. 175 :- S&F in repair of gun metal gate valves 15 mm with lever arm screwed both ends for iron pipes complete all as specified and directed.

Item No. 176 :- S & F in repair of PVC body bathroom cabinet with mirror fancy type made out of 5.5mm thick mirror of size 550 x 450mm complete, Model No 555 of PRAYAG or equivalent as approved complete all as specified and directed.

Item No. 177 :- M & L for preparation of old decorated plastered or unplastered surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds, mass and efflorescent salts and trading oil and greasy spots and evenly applying two coat of white wash on surfaces of walls etc complete all as specified and as directed.

Item No 178 : - BLANK

Item No. 179 :- M & L for Cement concrete Type C2 (1:3:6) (using 40mm graded stone aggregate) in surface channels and drains all as specified and directed.

Item No. 180 :- Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, mounds, mitered/stopped end etc. complete all as specified and directed.

Item No 181 : - BLANK

Item No. 182 :- S&F Reinforced concrete pipes,450 mm bore class NP2, laid and jointed complete with collars all as specified and directed.

Item No. 183 :- S&F Reinforced concrete pipes 600 mm bore class NP2, laid and jointed complete with collars all as specified and directed.

Item No. 184 :- Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding exc 4 Sqm but not exc 7.00 Sqm each complete all as specified

Item No. 185 :- Disconnecting existing water tanks of cap 500 Ltrs, setting aside (or lowering if required) for repairs, incl cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. and reconnecting the same tank after completion of roof treatment etc, all as specified (The contractor is responsible to keep the tanks under his own arrangment after disconnecting).

Item No. 186 :- Disconnecting existing water tanks of cap 1000 Ltrs, setting aside (or lowering if required) for repairs, incl cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. and reconnecting the same tank after completion of roof treatment etc, all as specified (The contractor is responsible to keep the tanks under his own arrangment after disconnecting).

Item No. 187 :- Demolition and breaking up drain pipes 150 mm dia (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

Item No. 188 :- M&L for cement concrete 25 mm thick type B-0, 1:2:4 (12.5mm graded aggregate) as in flooring/roof top etc complete all as specified and directed by Engr-in-Charge.

Item No. 189 :- M&L for providing reinforced cement concrete Type B-1, (1:2:4) (using 20 mm grade aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Item No. 190 :- Complete removal of existing treatment of any description, including preparation of surfaces, on wall surfaces of any description complete all as specified.

Item No. 191 :- M&L Pressed steel frames for doors with one with one or more rebates size of frame (125 x 60 mm ) including necessary fixing lugs, hinges, lock strike plate, etc.,complete all as directed and specified.

Item No. 192 :- S&F aluminium anodised barrel tower bolts of extruded section with 100 mm long bolt, all as specified .

Item No. 193 :- S&F aluminium anodised barrel tower bolts of extruded section with 200 mm long bolt, all as specified .

Item No. 194 :- S&F for small fittings of 2nd class hard wood, such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each.

Item No. 195 :- S&F 300mm length, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

Item No. 196 :-Providing and fixing pre painted steel sliding window 3-Track, 2 glass panel and 1 mesh panel sliding window fabricated from Roll formed sections made of galvanized Steel colour coated/powder coated (Base Steel as per IS 513 ‘D’ quality, galvanized as per IS 277 with zinc of 120 GM/Sq.mtr) with total coated thickness of 0.58mm. Primer coat with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with Alkyd backer of 5-7 microns or powder coated with pure polyester powder up to 50-60 microns thick. Section for external frame should be of 107x44mm, Section for shutter should be of 35x49mm. Section of mesh should be of 35 x 49 mm.The windows should be paneled with 5mm thick plain clear glass. Corner bracket for internal and external frame made of glass filled nylon. Gaskets are to be made of Ethyl Propylene Diamine Monomer (EPDM).The sections are to be cut to length, joined and assembled by means of corner bracket. The above frames should be fixed to the concrete/masonry walls by means of self expanding screws .

Item No. 197 :- Fixing only 15 mm bore of GI tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors.

Item No. 198 :- Fixing only 20 mm bore of GI tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors.

Item No. 199 :- Fixing only 25 mm bore of GI tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors.

Item No. 200 :- S & F in repairs Hand shower with 1.5 m CP Flexible SS Tube, multy flow Hand Shower , adjustable wall hook , rabbit cleaning system all as specified and directed. Make : Make Jaquar,Marc,Plumbe

Item No. 201 :- S&F in repair chromium plated brass Central hole basin mixer without popup waste system complete screwed down for15 mm GI bore pipe complete all as specified and directed. Make Jaquar,Marc,Plumbe

Item No. 202 :- S&F in repair PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified.

Item No. 203 :- S & F in repair Nipple 20mm dia suitable for HDPE water tank. (Minimum weight 20mm - 45gms)

Item No. 204 :- Providing and fixing of single rebate openable/fixed windows made of galvanized steel colour coated/powder coated (base steel as per IS 513 of “D" quality, galvanized as per IS 277 with zinc of 120 grams/sqm) with total thickness of coating 0.58 mm, primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick, outer frame section 48 x 50 mm, centre mullion section 48 x 50 mm, shutter section 47 x 20 mm and the fixed glass beading section 12 x 12 mm, outer frame and mullions shall consists rebate for glazed shutter with a 20 mm provision for guard bars/grills and the sections cut to length mitre joined with corner bracket, centre mullion fixed with mullion cap, handle, stay, 2 nos. SS( stainless steel) heavy duty pivot hinges per shutter and window fitted with 5mm thick plain float glass with EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing frames in concrete/masonry wall by means of self expanding screws, Including complete all as specified and directed.

Item No. 205 :- M&L for floor door stopper of brass body and tongue, anodised, with hard drawn steel spring, 140mm long, fixed in floor complete all as specified

Item No 206 & 207 : - BLANK

Item No. 208 :- M & L for stone kerb of roughly squared stone (lime and sand stone) of size 20cm(Length)x30cm(Height)x 80cm thick all surfaces hammer dressed so that the maximum depression from a straight edge held against the dressed surface shall not exceed 20 mm and finished thickness not less than 50mm and one edge should be (i.e. 20cm long side) slightly rounded/chamfered shaped incl jointing in cement mortar 1:4 struck flush incl etc complete all as specified and directed.

Item No. 209 :- M&L for preparation of concrete or plastered surfaces of any description over 10cm girth or width, not otherwise described and applying two coats of plastic emulsion paint over a coat of concrete primer complete all as specified and directed.

Item No 210 : S&F in repairs 50 x 15 mm size magnet door catcher for closing for Cupboard door shutter complete all as specified and directed .

Item No. 211 : S&F in repairs 18 mm thick factory made PVC sheet one side pre-laminated sheet kitchen cabinet shutter. The 18mm thick sheet shutter bent at 90 degree and finish all edges at level for marking edge lapping bending for 0.5 mm thick PVC sheet lapping at all four edges using bonding tape etc complete all as per specified and directed by Engr-in-Charge manufacturers specification .

Item No. 212 : S & F in repairs factory made PVC shelf/partition of required size consisting of panel of 18 mm thick required size consisting of panel of 18 mm thick celuka PVC ply and for supporting the hold of shelf /partition and shall provided 3 edges in size 18mm x 18 mm as per required length the front side of the edge visible in the front of the shelf/partition to be edge lipped by 18mm width x 1 mm thick PVC sheet of density 600 kg/cum manufactured by ISO 9001-2015 Certified Company , using solvent cement etc.

Item No. 213 :- S& F 100 mm size MS mat/glossy finish handle complete all as specified and directed .

Item No. 214 :- M&L for taking down/dismantling of existing roof treatment of any description such as old APP membrane roof treatment etc terracing including screed bed etc. Hessian base felt/tar felt etc. (any type and thickness)complete all as specified & directed.

Item No 215 : - BLANK

Item No. 216 :- M&L for rendering 15 mm thick in cement mortar 1:4 on roof surface including mixed with WPC as per manufacturer's instruction's and finishing the surfaces even and smooth without using extra cement complete all as specified and directed. Note :- WPC shall be measured and paid for separately as supply only under respective item of sch 'A'.

Item No. 217 :- Supply & providing water proofing roof treatment with polymeric standard water proofing membrane, Aqua flex manufactured by M/s Bengal Bitumen, MULTIPLAS STANDARD, manufactured by STP TEXAS Ltd/ Hyperplas manufactured by IWL Ltd having 10 years guarantee for water tightness complete all as specified and described as under:- (a) Preparation of RCC roof surface and applying one coat of polymeric modified bitumen 85/25 @ 1.2Kg/Sqm over a coat of polymeric primer @ 0.30 Kg/sqm including cleaning surface all as per manufacturer's specification complete all as specified and directed. (b) Supply & providing water proofing with 3 mm thick APP polymeric proofing membrane of 3Kg/Sqm HYPERPLAS STANDARD/ MULTIPLAS STANDARD consisting of 100 micron HMHDPE film centre core including coating the surface with compatible primer and torch application of membrane with 10cm overlaps as required thereof, complete all as specified and directed

Item No. 218 :- M&L for Cement concrete tiles 20cm x 20cm x 20 to 22 mm thick, machine pressed ( confirming to IS 1237); set jointed and pointed in neat cement slurry as on roof surface with grey cement and pigments, and cut and polished etc incl 15mm thick cement plaster in CM 1:4, complete all, as specified and directed

Item No. 219 :- Providing and fixing fixed louvers fabricated from Roll formed sections made of galvanized Steel colour coated/powder coated (base Steel as per IS 513 ‘D’ quality, galvanized as per IS 277 with zinc of 120 grams/Sqm) with thickness of 0.58mm coated sections to be primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder up to 50-60 microns thick, section for external frame 33 x 58 mm, glass holding flanges made of polypropylene, sections are to be cut to length, mitre joined with corner bracket. The above frames should be fixed to the concrete/masonry walls by means of self expanding screws incl window glass 4mm thick.

Item No. 220 :- S&F stainless steel rod 18 to 20mm dia including all necessary fixing arrangements in CB etc complete all as specified.

Item No. 221 :- S&F hasp and staple 125mm, safety type, aluminium anodised with alu hinge pin incl bolt to hinge plate and fixed with screws complete all as specified and directed.

Item No. 222 :- Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) incl edge of concrete.

Item No. 223 :- S&F PVC 500 litre capacity, triple layered polyethylene water storage tanks with threaded lead (cylindrical vertical with closed top) including hoisted and fixed in position, making connections, complete all as specified.

Item No. 224 :- S&F PVC 1000 litre capacity, triple layered polyethylene water storage tanks with threaded lead (cylindrical vertical with closed top) including hoisted and fixed in position, making connections, complete all as specified.

Item No. 225 :- S & F in repairs 32/40 mm PVC downpipe for kitchen sink fitted to Kitchen Sink incl all necessary brackets etc all as specified and directed by Engr-in-Charge.

Item No. 226 :- S&F stainless steel shelf closing hinges 75 mm size for PVC door shutters complete all as specified and directed

Item No. 227 :- S&F modular type stainless steel basket size 20 x 19 x 8 inches dia of wire not less than 3.00 mm ) of any shape with side sliding roller clip and sliding rails on both side fixed with steel screws incl all fixing arrangement complete all as specified and directed.

Item No. 228 :- As per item No 237 above but basket size 20 x 19 x 6 inches complete all as specified and directed.

Item No. 229 :- S&F modular type stainless steel Perforated Sheet Cutlery Basket size 20 x 19 x 4 inches dia of wire not less than 3.00 mm ) of any shape with side sliding roller clip and sliding rails on both side fixed with steel screws incl all fixing arrangement complete all as specified and directed.

Item No. 230 :- Dismantling timber scantlings unframed of any section , in any position complete all as specified.

Item No. 231 :- S&F in repair 40 mm dia, brass, knobs for cupboard fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed.

Item No. 232 :- Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings including ridge portion, complete all as specified.

Item No. 233 :- Providing and fixing Non-asbestos fibre reinforced cement cement plain building boards, 4mm thick fixed to iron angle and tee framework with screws / fasteners as in ceiling complete all specified and directed by Engr-in-Charge.

Item No. 234 :- All as per item No 233 above but fixing only complete all as specified and directed.

Item No. 235 :- M&L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matched including 15 mm thick screed bed in CM 1:4 complete all as specified and as directed by Engr-in-Charge

Item No. 236 :- All as per item No 235 but on vertical surfaces such as skirting incl including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

Item No. 237 :- M&L preparing of old plastered or unplastered surfaces of walls, cornices etc and applying one coat of cement base paint on old decorated surfaces of wall complete all as specified and directed.

Item No 238 : - BLANK

Item No. 239 :- M&L applying three coats of white wash on new Ceiling,chajja surface including preparation of surface.

Item No 240 : - BLANK

Item No. 241 :- M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade over 50 mm thick sand cusioning, complete all as specified and directed.

Item No. 242 :- S&F steel window with side hung shutter including projecting hinge, fixing lugs, steel handle and steel peg stay, complete without glazing bars dovetailed or welded complete all as specified and as directed

Item No. 243 :- S&F steel ventilator with top hung shutter with or without glazing bar, incl hinges, fixing lugs, steel peg stay, complete all as specified and as directed.

Item No. 244 :- Supply only 3 mm thick plain sheet glass ordinary quality and glazing with oil putty or wooden beads in square area n. exc. 0.5 Sqm in each pane complete . Note :- Fixing only rate is included in window/door shutter items considered therein

Item No. 245 :- Dismantling wrought iron or mild steel work of any description not otherwise provided for angle iron pickets or fencing post or any description etc, all as specified and directed.

Item No. 246 :- S & F Steel rolling shutters, with out ball bearing, as specified including top cover, anchoringrod,hasp and staple and one shop coat of primer; erected in position asindicated,but gear operated type with bevel gear box and crank handle complete all as specified and as directed.

Item No 247, 248 & 249 : - BLANK

Item No. 250 :- M&L for rendering 5 mm thick cement plaster on ceiling cement mortar (1:3) complete all as specified and as directed.

Item No. 251 :- M & L for preparation of old wall surfaces over 10 cm girth or width, not otherwise described and applying one coat of plastic emulsion paint on wall complete.

Item No. 252 :- S & F 16mm outer dia 3-layer PP-R P o l y p r o p y l e n e random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded p o l y p r o p y l e n e random fittings fixed complete to walls, ceilings or in floors etc.

Item No. 253 :- S & F 20mm outer dia 3-layer PP-R P o l y p r o p y l e n e random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded p o l y p r o p y l e n e random fittings fixed complete to walls, ceilings or in floors etc.

Item No. 254 :- S&F in repair CP Toilet paper holder, complete all as specified and directed by Engineer-incharge. MAKE:- Plumber Cat Part No. U-0916 complete all as specified and directed.

Item No. 255 :- S & F in repair 110 mm dia bore PVC (SWR) branch piece single (single Y) equal or unequal with rubber ring joints, fixed complete all as specified and directed.

Item No. 256 :- S & F in repair 75mm dia bore PVC (SWR) branch piece single (single Y) equal or unequal with rubber ring joints, fixed complete all as specified and directed.

Item No. 257 :- Demolition and breaking up drain pipe of dia 200 mm (internal dia) (salt glazed stoneware, AC or reinforced concrete) set in cement mortar complete all as specified and directed.

Item No. 258 :- M & L cement concrete bed to drain pipe including packing under and haunching against side of pipe after they are laid and tested in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate for the 200 mm internal dia of pipe complete all as specified and directed

Item No. 259 :- Supplying, laying, jointing and testing DWC HDPE, SN-8 confirming to IS 16098 pipe of size 200 mm internal dia of pipe, laid in trenches and Jointed complete. drain pipe of size 200 mm internal dia of pipe grade 'A' confirming to IS-651-1980 laid in trenches and jointed cement mortar 1:1 complete all as specified and directed.

Item No. 260 :- Provision double scaffolding system (cup lock type) as required for execution of work of civil repair/structural repair & rehabilitation /cleaning and /or pointing and/or applying chemical and removing it thereafter, on the exterior side of building/structure, up to 10 meter height, above ground level. Scaffolding shall comprise of additional rows in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5metre centre to centre, horizontal & vertical tubes joint with cup and lock system with M.S tubes, M.S tube challis, M.S. clamps and staircase system in the scaffolding , working platform , walkway wherever required , lighting arrangement etc. and maintaining it in serviceable condition. The scaffolding system shall be stiffened with bracing, runners, connecting with the building etc. wherever required, if feasible, for inspection or work as required locations with essential safety features for the workman etc., complete as per directions and approval of engineer - in - charge. Note:- 1. The front elevation area of the scaffolding shall be measured for payment purpose. 2. Scaffolding shall be removed after execution of work being contractor property.

Item No. 261 :- Cleaning reinforcement of total rust by tapping and using mechanical wire brush or any other suitable way including from behind and around the reinforcement bars to give it a totally rust free finished steel surface (Note:- concrete surface area with exposed surface shall be measured for payment).

Item No. 262 :- Providing and supplying the one competent, Polymer modified cementations anti- corrosive primer (having the technical parameters mentioned in material specifications ) formulated to provide dual protection of a polymeric barrier and an integral corrosion-inhibiting system, to the existing steel and additional steel provided before patching of damaged areas, using suitable tools and equipment inclusive of Material, Manpower and Equipment. BASF Master Emaco P130/ Fosroc Nitoprime Zincrich /Sika Rustoff 100 or other equivalent (mode of measurement - concrete surface area with exposed reinforcement)

Item No. 263 :- Providing and repairing the damaged concrete portion with single compnent, fibre reinforced, dual shrinkage- compensated thyrotrophic, cementious patch repair mortar (having the technical parameters mentioned in material specifications as per manufacture) capable of applying 25 mm thick in single layer initially by hand and finishing with trowed carefully compacting the same around the rebars and finishing to bring it in line with existing concrete surface with an average specified thickness inclusive of manpower , material complete as per directions by engineer - in - charge. Make:- Master Emaco 5348 of BASF Renderoc HB-60 of Fosroc/Sikadur 41 of Sika or equivalent.

Item No. 264 :- Description same as per item No. 263 above but in 50 mm thickness in two layers complete.

Item No. 265 :- Providing and fixing shear connections of 10 mm dia HYSD steel with two components, styrene & cement free epoxy- acrylate fixing and anchoring compound ( having the technical parameters mentioned in material specifications) using standard sealant applicator gun after drilling holes of 12mm diameter to a minimum depth of 100 mm at required locations, inclusive of all material, manpower and equipment (Make: Master flow 935 of BASF/ Lokfix P25 of Fosroc or equivalent)

Item No. 266 :- Providing strengthening to columns by all round jacketing to specified columns up to top of foundation level using minimum 125 mm thick M-45 self compacting concrete as directed, including removing loose concrete, cleaning the reinforcement mechanically, using wire brush etc. complete but excluding formwork and reinforcement ;Cement content: 380Kg/ cumAdmixture: Master Glenium of BAF or equivalent.Note: Thickness of 125mm shall be measured from the outer face of main reinforcement & additional material poured beyond the same shall not be separately measured and paid for.including necessary formwork.

Item No. 267 :- S&F in repair Gun metal globe or gate valves high pressure with polythene float and fly nut complete screwed for iron pipe or for unions of 20 mm bore and fixed in repairs, all as specified and directed

Item No. 268 :- Dismantling water tanks and removing to store Capacity of tank exc 250 and nexc 500 litres complete all as specified and directed.

Item No. 269 :- Preparing old surfaces applying three coats of white wash in ceiling complete all as specified.

Item No. 270 :- Demolition of cement concrete Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

Item No 271 : - BLANK

Item No. 272 :- M&L Factory made solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded prelaminated PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per pacification & drawing complete all as specified and directed.

Item No 273 : M & L in repairs 18/19 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

Item No. 274 : Dismantling of plain steel sheeting carefully, any gauge, thickness, from the top of parapet wall and refixing the same at the existing place with screws, fasteners etc, after plastering or other treatment of of parapet, complete all as specified.

Item No. 275 : Providing and fixing of double rebate openable/fixed windows made of galvanized steel colour coated/powder coated (base steel as per IS 513 of “D" quality, galvanized as per IS 277 with zinc of 120 grams/sqm) with total thickness of coating 0.58 mm, primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick, outer frame section 72 x 55 mm, centre mullion section 72 x 50 mm, shutter section 47 x 20 mm,fly mesh section 40 x 20 mm and the fixed glass beading section 12 x 12 mm, outer frame and mullions shall consists rebate for glazed shutter, fly mesh and 20 mm provision for guard bars/grills, the sections cut to length mitre joined with corner bracket, centre mullions fixed with mullion cap, stay, handles, latch, 2 Nos of heavy duty stainless steel pivot hinges per shutter and panelled with 5mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade), fitted using EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing windows in the concrete/masonry wall by means of self-expanding screws, including 10mm Square bars welded to 6x12mm flat at a distance 150mm c/c (pitch) etc. complete as per the direction of Engineer in Charge.

Item No. 276 :- Providing and injecting chemical emulsion along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 Ltrs/mtr including driling & plugging holes etc all as specified and directed by Engr-in-Charge.

Item No. 277 :- S&F PVC(SWR) pipes, 150 mm external dia double socketed in any length with or without rubber joints, fixed to walls with PVC brackets/clips complete all as specified.

Item No. 278 :- S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed

Item No. 279 :- M&L 16 to 18mm thick Granite (of any type) work (table rubbed and polished and exposed visible edge moulding/rounding ) in steps, jambs, pillars, window cills, cooking platforms and like including 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed

Item No 280 : - BLANK

Item No. 281 :- S & F Powder coated aluminium sliding glazed windows with three track shutter sliding (two shutters glazed and one shutter wire mesh) shall be two part as upper patr shall be three movable shutter and lower part consist three shutter (one openable in centre and both side fixed type shutter with frosted glass) with following specification and making good the adjacent side of jambs of windows by plastering in CM 1: 3 even and smooth complete etc . shifting of existing cooler stand where required complete all as specified and as directed by Engr-in-charge. (i) Windows frame of cross section 101mm x 44mm x 1.5mm thick. (ii) Three way track for sliding shutters of cross section 91.8mm x 31.75mm x1.1mm thick. (iii) Sliding shutter frame of cross section 40 x 18 x 1mm thick. (iv) 4 mm thick glass superior quality. (v) IDPE Rubber guasket for fixing of glass. (vi) Locking cleats per shutter -01 Nos. (vii) Sliding rollers per shutter - 02 Nos. (viii) Stainless steel wire cloth 0.30mm nominal dia of wire and average width of aperture 1.40mm for shutters 01 Nos. (Ix) fixing screw for frame with wall per windows- 08 Nos.

Item No. 282 :- S & F powder coated aluminium ventilator cross section conforming to IS 63.5x38.10x1.5mm consisting of two partions upper portion shall have louvers with 3mm thick pin headed glass and aluminium wire cloth 0.30mm nominal dia of wire and average width of aperture 1.56m fixed with aluminium beads and securing on outer face of frame and lower portion of ventilation shall be fixed with 3mm thick pin headed glass with IDPE rubber gasket including aluminium beads, including preparation of jombs all around in CM 1:3 finishing even and smooth complete all as specified and directed.

Item No. 283 :- M&L for two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489-2004, Alkali and fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) 1.43 litre/10sqm over and including priming coat of exterior primer applied @ 0.90 litre /10sqm over new surface including preparation of new surfaces.

Item No. 284 :- M&L preparation of old surface of wall and apply one coats of Anti fungal weather coat Acrylic exterior emulsion paint complete all as directed and specified. Make : Asian (Apex Ultima), Berger weather coat all Guard, ICI Dulux (Weater shield Max), Nerolac (Excel Total).

INTERNAL ELECTRIFICATION

Item No. 285 :- Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc complete all as specified and directed at site.

Item No. 286 :- Taking down ceiling fan/ exhaust fan/ wall fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of concerned AGE E/M complete all as specified and as directed.

Item No. 287 :- Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed.

Item No. 288 :- Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface complete all as specified and directed.

Item No. 289 :- Taking down existing geyser of any capacity after disconnecting all necessary electrical and water supply connections and deposit to MES store yard of concerned AGE E/M Mhow complete all as specified and as directed.

Item No. 290 :- Taking down existing single phase electric energy meter of any capacity after disconnecting all necessary electrical connections and deposit to MES store yard of concerned AGE E/M Mhow complete all as specified and as directed.

Item No. 291 :- M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for the following :-

(a) One light point controlled by one, one way switch 5 Amps

(b) One light point controlled by two, two way switch 5 Amps

(c) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

(d) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(e) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

(f) One bell point controlled by one, bell switch 5 Amps

Item No. 292 :- Description all as per item No 291 here in before but using 2.5 sq mm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

Item No. 293 :- Description all as per item No. 291 here in before but using 4.0 sq mm single core copper conductor FRLSH cable of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 4.0 sq mm PVC insulated copper conductor FRLSH cable as earth continuity conductor along with wiring and connecting to the common eath dolly. (for AC Point)

Item No. 294 :- M&L for point wiring with 1.5 Sq mm single core PVC insulated unsheathed copper FRLSH multi stranded conductor cable in and including Concealed PVC conduit of size 20/25mm ISI marked inclusive of tees ,bend ,elbows etc upto and including sunk in anodized pressed steel box of 1.6 mm thickness, 60 mm deep for housing switch socket etc with white laminated 3 mm thick hylam sheet cover ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sq mm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by Engr-in-charge for following :-

(a) One light point controlled by one, one way switch 5 Amps

(b) One light point controlled by two, two way switch 5 Amps

(c) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

(d) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(e) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

(f) One bell point controlled by one, bell switch 5 Amps

Item No. 295 :- Description all as per item No 294 here in before but using 2.5 sq mm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

Item No. 296 :- S & F for Switch Piano type single pole 5 amp, 230 Volts complete all as specified and directed at site.

Item No. 297 :- S & F for Switch Piano type 2 way switch 5 amp, 230 Volts complete all as specified and directed at site.

Item No. 298 :- S & F for Switch Piano type single pole 15/16 amp, 230 Volts complete all as specified and directed at site.

Item No. 299 :- S & F for socket outlet 2 in 1 , 5 pin, 5 amp, 230 Volts complete all as specified and directed at site.

Item No. 300 :- S & F for socket outlet 2 in 1 , 5 pin, 5/15 amp, 230 Volts complete all as specified and directed at site.

Item No. 301 :- S & F for stepped type electronic fan regulator flushType complete all as specified and directed at site.

Item No. 302 :- S & F for switch bell push piano type 5 amp, 230 Volts Complete all as specified and directed at site.

Item No. 303 :- S & F for Modular Switch piano flush type, single pole, one way, and 5/6 Amp single module complete all as specified.

Item No. 304 :- S & F for Modular Switch piano flush type, single pole, two way, and 5/6 Amp single module complete all as specified.

Item No. 305 :- S & F for Modular Switch piano flush type, single pole, one way, and 15/16 Amp single module complete all as specified.

Item No. 306 :- S & F for Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

Item No. 307 :- S & F for Modular Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

Item No. 308 :- S & F for modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

Item No. 309 :- S & F for for Bell push modular 6 Amps single module complete all as specified.

Item No. 310 :- S & F for Ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete all as specified

Item No. 311 :- S & F for Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed

Item No. 312 :- M & L for Sub main wiring with approved colour coding as per IS with four single core PVC insulated FRLSH cable with stranded copper conductor of size 10 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc two runs of PVC insulated with 6 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Four runs of 10 sqmm cable, two runs of 6 sqmm cable and one run of PVC conduit will be measured as one unit

Item No. 313 :- M & L for Sub main wiring with approved colour coding as per IS with four single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc two runs of PVC insulated with 4 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Four runs of 6 sqmm cable, two runs of 4 sqmm cable and one run of PVC conduit will be measured as one unit

Item No. 314 :- M & L for Sub main wiring with approved colour coding as per IS with four single core PVC insulated FRLSH cable with stranded copper conductor of size 4 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc two run of PVC insulated with 4.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Four runs of 4 sqmm cable,two run of 4 sqmm cable and one run of PVC conduit will be measured as one unit

Item No. 315 :- M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 4.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable,one run of 4 sqmm cable and one run of PVC conduit will be measured as one unit

Item No. 316 :- S & F for lamp holder , PVC / Polycarbonate type with back plate suitabl for batten/ slanting fittings complete all as specified and directed.

Item No. 317 :- S & F for Highly efficient LED Bulbs, 10 watts in B-22 cap complete all as specified and directed. Make Bajaj, Havells, HPL

Item No. 318 :- S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. Make :- Make Bajaj Cat part No BCLAB 20W WH LED P, Wipro Cat part No LL20-281-XXX065-ALI or its equvalent in Philips, Havells.

Item No. 319 :- S & F for Box type (decorative) wall mounted LED light fitting including LED tube 4' x 20 watts with output of 2000 lumens, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. Make :- Make Bajaj Cat part No BLRB-DB 218 & BLRB AL 22L CW LED (20W), or its equvalent in Wipro, Philips.

Item No. 320 :- M&L for Suspension (Pendant) luminaires 20 watts with efficient Diffuser ensuring perfectly uniform illumination, ensured optimised and unparalleled light distribution. Inter-connectable luminaires for aesthetically appealing downlight application includind necessary fixing the hanging wiresfrom RCC ceiling with suitable fastners,mounting end cap, making good diturbed surfaces with necessary mason and painting work to match with the existing surfaces all as specified and directed. Make :- Make Bajaj Cat part No BPCS 20 W LED 4F DH WH, or its equvalent in Wipro, Philips.

Item No. 321 :- S & F for Decorative wall mounted luminaire made out of polycarbonate with unbreakable globe suitable for LED bulb and provosion of LED bulb 10 watts complete all as specified and as directed. Make Havells Cat No LHDLO6160099 or its equvalent in Philips, Bajaj.

Item No. 322 :- S & F for LED 10 watts batten aluminium extruded with decorative end caps complete all as specified and as directed. Make- Bajaj Cat Part No BCLSB 10 NW or its equivallent model in Wipro, Philips.

Item No. 323 :- S & F for Energy saving new generation 10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation and necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed. Make :- Bajaj Cat No BIBWP 10W LED or its equvalent in Philips, Wipro.

Item No. 324 :- S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 30 watts, lumen output >=110 lm/W with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge. Make :- Bajaj Cat part No ENXT P 30L WH PO PC SD or its equvalent in Philips, Wipro.

Item No. 325 :- S & F for LED luminaire 600 mm x 600 mm square LED panel 36 watts, lumen output >=110 lm/W, 220 volts, AC surface mounted type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling, including connecting up with driver three core flexible copper conductor cases of suitable size complete all as directed by Engineer- in-charge.

Item No. 326 :- S & F for LED luminaire 600 mm x 600 mm square LED panel 35/36 watts, lumen output >=122 lm/W, 220 volts, AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling, including connecting up with driver three core flexible copper conductor cases of suitable size complete all as directed by Engineer- in-charge.

Item No. 327 :- S & F for LED down light luminaire round shape 15 watts, white finish operating voltage 150 Volts - 270 Volts AC, 50 Hz, recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling, including connecting up with driver three core flexible copper conductor cases of suitable size complete all as directed by Engineer- in-charge.

Item No. 328 :- S & F for LED down light recess mounted luminare, square type 15 watts with efficiency of 100 lumens per watt, sleek design with polycarbonate body housing polycarbonate diffuser white finish operating voltage 150 Volts - 270 Volts AC, 50 Hz all as per Make- Bajaj Cat Part No BPSLR 15W NW PRO SQ, or its equavalent in Wipro, Philips.

Item No. 329 :- Fixing only for LED luminaire 600 mm x 600 mm square LED panel 35/36 watts, recess mounted light fitting obtain from item No 285 with necessary electrical connections complete all as specified and as diredcted

Item No. 330 :- S & F Integral decorative LED bollard with polycarbonate diffuser square shaped with IP 65 protection suitable for 9 watts LED bulb with necessary MS base box made out of MS sheet of 2 mm thick of suitable size abbended in PCC 1:2:4 base, elecrical connections with adequate size including removal of old unserviceable one complete as all specified and as directed. Make: Bajaj Cat part No BGBOS 600 9W LED, Philips Cat Part No BCP 150 LED 150 WW or its equavalent in Wipro.

Item No. 331 :- S & F for LED post top lantern 25 watt light fitting made of cast aluminium spigot housing with decarative opal acrylic diffuser with IP 65 protection complete with all accessories fixed on GI pipe 50 mm dia including removal of old unserviceable one complete all as specified and directed. Make Bajaj Cat part No BGCTN 25W LED WW or its equavalent in Philips, Wipro.

Item No. 332 :- S & F for TPN phase segregated distribution board double door vertical type 6 way 415 volts, IP 43, IK 09, 50Hz suitable for MCCB incommer IP 43 protection on wall/ floor with necessary cement work and electrical connections complete all as specified. Make: L&T Cat Part No DBPGL006DD or in equavalent in Legrand, C & S, Schneider, ABB

Item No. 333 :- S & F for sheet metal enclosure MCB DB TPN 6 way Vertical type with 200 Amps rated bus bar 415 volts, IP 43, IK 09, double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

Item No. 334 :- S & F for sheet metal enclosure MCB DB TPN 4 way Vertical type with 200 Amps rated bus bar 415 volts, IP 43, IK 09, double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

Item No. 335 :- S & F for sheet metal enclosure MCB DB SPN 12 way with 200 Amps rated bus bar 240 volts IP 43, IK 09, double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

Item No. 336 :- S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts IP 43, IK 09, double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

Item No. 337 :- S & F MCCB TPN 415 volts, Icu=100% Ics with rupturing capacity 25 KA suitable for fixing on DB of capacity 63 to 100 Amps with extended terminals complete all as specified..

Item No. 338 :- S & F for MCB tripple pole and neutral rated capacity 63 Amps, 415 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed

Item No. 339 :- S & F for MCB Single pole and neutral rated capacity 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

Item No. 340 :- S & F for MCB Single pole rated capacity 40 to 63 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

Item No. 341 :- S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

Item No. 341 (A) :- M&L for single pole and earth encolsure with a two pin and earth plug with socket 240 Volts, 50 Hz complete with onesingle pole MCB SP 20 Amps complete all as specified and directed.

Item No. 342 :- M&L for Triple pole and earth encolsure with a three pin and earth plug with socket 415 Volts, 50 Hz complete with one triple pole MCB TP 32 Amps complete all as specified and directed.

Item No. 343 :- S & F for Modular type TV Socket out let complete all as specified and as directed.

Item No. 344 :- S & F for Modular typeTelephone socket outlet complete all as specified and direced.

Item No. 345 :- S & F for Modular type RJ 45 with shutter complete all as specified and as directed.

Item No. 346 :- Labour only for refixing the celing fan/ Exhaust fan obtained from item No 286 above with replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal including over hauling the fan, painting of ceiling fans complete with two coats synthetic enamel paint by spraying including filling cavities with filler after cleaning all dust etc and writting the MES Number with synthetic enamel paint complete all as specified and as directed.

Item No. 347 :- Labour only for refixing the wall fan obtained from item No 286 above including over hauling the fan and cleaning all dust etc and writting the MES Number with synthetic enamel paint complete all as specified and as directed.

Item No. 348 :- S & F for ceiling fan, 230 Volts, 50Hz, 1200 mm sweep with down road (up to two mtr or as required), canopy, blades, BLDC motor etc and service value of the fan shall be greater than 7.0, along with compatible capacitor type fan regulator as per BIS with necessary accessories and electrical connections from ceiling rose to fan teriminal including writting the MES Number with synthetic enamel paint complete all as specified and as directed.

Item No. 349 :- M&L for wall fans 450 mm sweep, 230 volts, 50 Hz complete with mounting brackets all as specified and directed

Item No. 350 :- S & F for water heater storage type (Geyser) vertical/ Horizental type as per site requirement with inner container of capacity 25 ltrs, electrically operated, AC 230 Volts,BEE 5 star rated (The inner tank should have a minimum 07 years warranty from the manufacturer. Additional warranty on models having warranty less than Additional warranty on models having warranty less than 07 years will not be accepted.) ISI marked including 04 Nos of hold fashner nuts required suitable size fixed in brick wall, PVC connection pipe hot & cold for Officers JCO's and OR single Accn incliding writting the MES Number with synthetic enamel paint complete all as specied and as directed

Item No. 351 :- S & F for energy efficient exhaust fan of 230/300 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base including writting the MES Number with synthetic enamel paint compelte all as specified and directed.

Item No. 352 :- S & F for energy efficient exhaust fan of 380 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base including writting the MES Number with synthetic enamel paint compelte all as specified and directed.

Item No 353 :- S & F for energy efficient exhaust fan of 450 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base including writting the MES Number with synthetic enamel paint compelte all as specified and directed. Note for Item No 351, 352 & 353 :- Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted).

Item No 354 :- S & F for PVC non-metallic rigid conduit ISI marked heavy duty white/ Ivory colour and its accessories heavy duty ISI marked of size 40 mm dia for LAN, telephone and TV connections including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed.

Item No. 355 :- S & F for PVC non-metallic rigid conduit ISI marked heavy duty white/ Ivory colour and its accessories heavy duty ISI marked of size 25 mm dia for LAN, telephone and TV connections including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed.

Item No. 356 :- S & F for PVC non-metallic rigid conduit ISI marked heavy duty white/ Ivory colour and its accessories heavy duty ISI marked of size 20 mm dia for LAN, telephone and TV connections including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed.

Item No 357- Supply and fix Hot dipped Galvanized CABLOFIL wire mesh cable trays should comply Standard EN ISO 1461, manufactured with a longitudinal 'T- welded' safety edge, constructed with 50 X 100 mm mesh configuration including couplers, covers with clips and wall mounting accessories as per site requirement. Supports, brackets or hangers, covers designed loading capacities of the brackets and the hanger torques must be tested in accordance with the standard IEC 61537 of size 150 mm width x 54 mm height complete all as specified and as directed.

Item No. 358 : Supply, installation, commissioning and testing indoor type LT wall mounting Panel Board of minimum size 1.20 m (height) x 1.20 m (breath) x 0.30m (depth) factory made CPRI approved panel, weather, dust & vermin proof indoor, double door, front openable, including four comparment for fixing of 12 Nos single phase meter and MCB and porviding glass view for reading of meter and providing rubber/ PVC gasket of suitable size all sides of door, with copper busbar wrapped with PVC tape/sleeves with maintained the colour code and copper strip/wire busbar of suitable size to MCCB input and MCCB/MCB output of suitable length for connection of cable from main busbar, made out of 2.00 mm thick mild steel CRCA sheet with suitable size angle iron supporting frame including applying two coats of Powder coated paint over a coat of red oxide zinc chrome primer over exposed external & internal surfaces suitable for 3 phase 4 wire system 415/440 volts grade including complete internal wiring with 1.5 sqmm copper wire and connections of all outgoing / incomming existing cable of any size and removing of old unsv panel complete all as directed by Engineer-in-Charge. (For G+1 Single living officers Accn)

OUTGOING (a) MCB, Single pole & neutral, 40 amps, 240 volts, ‘C’ curve, 10 KA all complete as specified and as directed - 10/12 Nos (b) Fixing only serviceable existing electric meter- 10/12 Nos (obtained from item No 300 above)

Item No 359 :- M & L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia. medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR part I including excavation and earthwork in any type of soil/strata and testing on completion. Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.

External Electric Supply

Item No. 360 :- Supplying and laying un-reinforced precast concrete cable cover, class LV, type 1 with peak of size 250 mm x 150 mm x 40 mm with minimum average breaking load 200 Kg as per IS 5820:1970, ISI marked all as specified and directed.

Item No. 361 :- Supply , spread and filling for clean dry river sand in trenches/ducts for cushioning to cable, 8 cm in depth before laying the cable and 15 cm in depth after laying the cable complete all as specified. Note :- Punned thickness only will be measured and paid.

Item No. 362 :- Supply & lay GI tubing light grade in protection of cable at road crossing /hard standing/pole protection fixed with clamps as per site requirement etc of following sizes complete all as specified and directed .

(a) 50 mm dia bore

(b) 40 mm dia bore

(c) 25 mm dia bore

Item No. 363 : Taking down existing old unserviceable LT UG/ service cable of any description and size complete all as specified and directed.

Item No. 364 :- Supply and laying & testing and commisioning LT underground cable 1100 volts grade, XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ducts, on poles etc of size complete all as specified and directed

(a) 06 Sqmm x 2 core

(b) 16 Sqmm x 4 core

(c) 25 Sqmm x 4 core

(d) 35 Sqmm x 3.5 core

(e) 70 Sqmm x 3.5 core

SCHEDULE "A" (Schedule of credit) Schedule of Credite Rs 1377258.00 (Minus) inserted by the MES (Note : Credite amount shall be deducted manually to arrive net bid amount)

nhsaluji and associates

SHREE KRISHNA INFRASTRUCTURE

M/S Umashanker Mishra

RAMJI DAS DHAL CONSTRUCTION PVT LTD

JAIDEV SINGH CHADHA