SPL REP TO BLDG NO 40, 41 SM LINE, PROVN OF BOUNDARY PILLARS AT CAMPING GROUNDS, TOILET NEAR RADIAL WELL, CONNECTION FROM WATER TANK TO KITCHEN AT AREA UNDER AGE B/R-I AT KAMPTEE.

Amount

Dismantling of brick work or stone/boulder masonary built in cement mortar including all quoins, arch, pillars etc complete all as specified and directed.

Dismantling of asbestos cement/ translucent sheet corrugated/ semi-corrugated sheets in roof coverings including ridges complete all as specified and directed.

Excavation in post holes (or similar holes) each not exc 0.5 cum, getting out in soft/ loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exc 50m and making good to surface complete all as specified and directed.

Excavation over areas not exc 1.50m deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches not exc 1.5m in deepth and 1.5m in width and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches exc 1.5m in deepth but not exc 3.00 m and 1.5m in width and getting out in soft/loose soil complete all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

M&L for sand filling under floor or in foundation including watering and consolidation complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in hard/dense soil complete all as specified and directed.

Removing excavated material (soil) not exc 50m and deposited where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description, not otherwise specifically provided for complete all as specified and directed.

M&L for structural rolled mild steel as in roof trusses (framed), purlins, crane gantries, rail and fastenings and heavy brackets framing (beam, tee, angle, channel or flat section) and similar works conforming to Fe-410 -O complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

M&L for 18-20mm thick kota stone (machine cut) slab flooring laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, mirror polishing over and including screed bed 15mm thick in CM 1:6 complete all as specified and directed.

M&L for kota stone slab 18-20mm thick including rubbing, mirror polishing in riser of steps, skirting, dado and pillar laid over backing coat of 10mm cement screed bed in CM 1:4 complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa as in roof covering/ cladding to wall, valley gutter fixed with self tapping screws complete all as specified and directed.

M&L plain cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in coping, haunching, rounded or chamfered on edges including necessary from work complete all as specified and directed.

Taking down cement or cement lime plaster, of any desription on brick or stone wall, etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for brick work with fly ash bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 (using old size brick) complete all as specified and directed.

M&L for rendering 10mm thick on brick or concrete surfaces in CM 1:6, finished even & smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on brick or concrete surfaces in CM 1:4, finished even & smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick on brick or concrete surfaces of ceiling /chajja's in CM 1:3, finished even & smooth, without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on other than fair faces of brick work in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick on surfaces of ceiling in cement mortar (1:3) and finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new or previously untreated steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel and iron of any description not exc 10cm width or girth, not when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying three coats of white wash on ceilings complete all as specified and directed.

M&L for prepation of new surfaces and applying two coats of exterior grade weather proof paint, water based on wall surfaces complete all as specified and directed.

M&L for preparation of new surfaces of wall & applying two coats of oil bound distemper over a coat of birla wall care putty complete all as specified and directed.

Taking down door / window frame with shutter (without taking of shutter from the frame) area not exc 1.5 sqm complete all as specified and directed.

S&F steel window with side hung shutters (glaze & gauze shutter) including projecting or box stype hinges with steel handle peg stay and divided into square with glazing bars, dovetailed or welded to receive glazing or gauzing including one coat of primer including fixing of flat iron hold fast of size 25 x 5mm complete all as specified and directed.

All as per item No 32 above but without glazing bars complete all as specified and directed.

S&F framed guard bars with mild steel square bars with ends of bars shouldered and or riveted and similar work confirming to Fe 410-O or Fe 310-0 complete all as specified and directed.

S&F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F anodized aluminium windows and ventilator shutters, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screws, locking arrangement etc complete all as specified and directed.

S&F sheet glass of 4mm thick, ordinary quality and glazing complete all as specified and directed.

Taking down shutters only of any description, area exc 1.00 sqm but not exc 2.00 sqm complete all as specified and directed.

S&F 30mm thick flush shutters solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and avarage width of aperature 1.40mm dia complete all as specified and directed.

Taking up or down steel tubing connection and S&F GI tubing 15mm bore, medium grade with all fittings and fixed to wall or laid in floors etc complete all as specified and directed.

Dismantling of wall and ceiling board (fibre, insulation etc) or insulation board, slabs, blankets, any thickness including cover fillets complete all as specified and directed.

M&L for non-asbestos designer fiber cement building boards of size 595x 595x 4mm fixed or laid/inserted to GI frame work with screws/ clips as in ceiling laid flat or sloping complete all as specified and directed. Note:- GI frame work will be measured and paid for separately.

S&F GI framework for seamless ceiling of size 600mm x 600mm comprising of hot deep galvanized powder coated perimeter angle 0.43mm thick of size 24x24mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre, main runner Tee section 0.4mm thick with height 38mm and cross approx 1200mm centre to centre with GI cleat and steel expansion fasteners, including drilling holes for 4mm dia GI wire suspender and clips etc complete as per manufacturer's recommendations complete all as specified and directed. Note:- (i) Ceiling baords shall be measured separately. (ii) The grid system shall be as per specification of make as specified and directed.

Taking down existing water proofing treatment including PCC padding, mortar etc and disposal of rubbish out side MD land and hacking for key, scrubbing down with water complete all as specified and directed.

M&L for 40mm thick cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in padding, copping using water proofing liquid compound as per manufacturer's instructions laid to proper slope and gradient, finished even and fair complete all as specified and directed. Note:- Water proofing liquid compound shall be measured and paid separately.

M&L for provision of water proofing treatment by using APP torch on miniral/ slate finished membrrance over roof and vertical surfaces including preparation of surfaces and applying oil based bituminous primer coat @ 0.30 ltr per sqm on clean and dry surface and then providing APP membrane having non woven polyster film reinforcement with 3mm thick and weight not less than 3 .00 kg/sqm and finished on top with mineral/ slate finished torch on system laid with 100mm & 150mm over lap on side & end laps resepectively laid over rendering 20mm thick in CM 1:3, finished even & smooth without using extra cement using water proofing liquid as per manufacturer's instructions complete all as specified and directed. Note:- Water proofing liquid will be measured & paid separately.

Dismantling of floor, hearth or wall tiles including cement mortar bedding, but not backing, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position, not otherwise specifically provided for complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4, type B-0 (using 12.5mm graded stone aggregate) as in sunken floor using liquid integral WPC @ 200 ml/50Kg of cement complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M&L for rendering 15mm thick on brick or concrete surfaces in CM 1:4 using water proofing liquid compound as per manufacturer's instructions and finished even & smooth without using extra cement complete all as specified and directed.

Supply only liquid integral water proofing admixture of Make: Pidilite or its equivalent complete all as specified and directed.

M&L for two coats of brush bond liquid compound of Make: Fosroc (Fosroc chemical Ltd) or its equivalent water proofing coating over plastered surfaces of sunken portion as per manufacturer's instructions complete all as specified and directed.

M&L for 50mm thick PCC 1:2:4 type B1 (using 20mm graded stone aggregate) for floor complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate), as in plinth protection and finishing surfaces even & smooth without using extra cement including mist filling in the joints complete all as specified and directed.

M&L for PCC type E2 1:5:10 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base to floors finished fair and even complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete etc complete all as specified and directed.

M&L for cement concrete 1:2:4 type B2 (using 40mm graded stone aggregate) as in foundations, filling, post hole filling and mass concrete complete all as specified and directed.

M&L for 100mm thick PCC 1:2:4 type B2 (using 20mm graded stone aggregate) as in hard standing, PCC path and similar works, finished even and smooth without using extra cement complete all as specified and directed.

M&L for providing precast cement concrete 1:1.5:3 type B1 (using 20mm graded stone aggregate) in posts, boundary pillars, etc and setting in cement mortar 1:4 with joints to match complete all as specified and directed.

M&L for RCC 1:1 1/2:3 type A1, nominal mix in beams, cantilivers, bressumers and lintel over 1.5mtr span complete all as specified and directed.

All as per item No 63 above but in slab supported on walls, beams and colmns in floors, roofs, landings, balconies etc complete all as specified and directed.

M&L for 40mm thick cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) as in PCC flooring laid in slope in 1:30 in alternative bays. Exposed surfaces finished even and smooth using extra cement including racking out joints between pannel to pannel and pannel to wall and plugging the same with bituminous mastic using bitumen and mixure in 1:3 complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3.0mtr in length. Exposed surfaces finished even and smooth using extra cement including racking out joints between pannel to pannel and pannel to wall and plugging the same with bituminous mastic using bitumen and mixure in 1:3 complete all as specified and directed.

Dismantling of plain sheeting, any gauge / thickness and S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in weather boarding/ eaves board in approved design/ pattern/ shape to match with existing adjacent water boarding/ eaves boards and fixed with self tapping screw/ nut bolt/ normal GI screw/ nails etc as per site requirement at any height/ position complete all as specified and directed.

S&F 100mm long mild steel, medium weight, cold rolled butt hinges and fixed with screw/ welded to frames etc complete all as specified and directed.

S&F 150mm extruded aluminium handles, fabricated type, anodised etc complete all as specified and directed.

S&F 200mm long aluminium, anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F 300mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed complete all as specified and directed.

S&F in repair wall mixer 3 in 1 system with provision for both hand shower and overhead shower complete with 115mm long bend pipe connecting legs & wall flange complete all as specified and directed. Make:- Prayag Cat No-7280 or equivalent.

S&F in repair 15mm dia bib taps, cast copper alloy CP with crutch or butterfly handle, fancy type screwed down screwed for iron pipe or for brass ferrule and fixed completed all as specified and directed.

S&F in repair angle cock (Muse) complete all as specified and directed. Make:- Prayag Cat No 9310 or equivalent.

S&F in repair vitreous china wash down, water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed.

M&L for light shade vitrified ceramic tiles 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles over & including 15mm thick screed in CM 1:6 finished even and fair complete all as specified and as directed.

All as per item No 76 above but in skirting / dados including screed base plaster of 10mm thick in CM 1:4 finished even and fair complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles including 15mm thick screed bed or bedding layer in CM 1:6 finished fair and even for laying floor finishes/ tiles etc complete all as specified and directed.

M&L for coloured glazed ceramic tiles 300 x 450 x 7mm thick, on vertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles including rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 as backing coat to receive wall tiles/ skirting/ dados complete all as specified and directed.

M&L granite (of any type) tiles/slab 20mm thick, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in WHB, kitchen platform including 15mm thick screed bed in CM (1:6) etc complete all as specified and directed.

M&L for chequered tiles 300 x 300 x 25mm thick, rubber finished, set jointed and pointed in neat and cement slurry in floors with grey cement and pigment complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No 82 above but 5mm and over up to incl 10mm dia in stirrups etc complete all as specified and directed.

All as per item No 82 above but 8 to 10mm dia as in stirrups, spacers and binders complete all as specified and directed.

M&L for 40mm thick damp proof course to horizontal or vertical surfaces including necessary formwork in 1:2:4 type B-0 complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for form work to sides of plinth beams finished fair and rough complete all as specified and directed.

All as per item No 87 but for soffits of slab complete all as specified and directed.

M&L for prepation of old decorated surfaces and applying two coats of exterior grade weather proof paint, water based on wall surfaces complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of oil bound distemper over a coat of wall care putty complete all as specified and directed.

M&L for preparation of old decorated surface on walls and applying two coats of white wash complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for preparation of new undecorated plastered wall / concrete surfaces and applying three coats of white wash etc complete all as specified and as directed.

M&L for preparation of new plastered surfaces and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for hardcore of gauge not exc 63mm deposited, spread and levelled in layers not exc 15cm thick watered and rammed to a true surface for plinth protection / path complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, & fixing in opening complete all as specified and directed.

S&F factory made solid PVC moulded door shutter (with wood free EPS), 28 to 30mm thick (Stiles) with 2, 4, 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face & fixing in frame at site as per drawing shown on SSR complete all as specified and directed.

S&F 100mm long mild steel, medium weight, cold rolled butt hinges and fixed with screw/ welded to frames etc complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, anodised of 125mm long complete all as specified and directed.

S&F aluminium anodised barrel tower bolts of extruded section and fixed of 100mm long complete all as specified and directed.

S&F in repair 300mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, peg stay to receive glazing or gauzing and one coat of primer including fixing of hold fast size 25 x 5mm of flat iron etc complete all as specified and directed.

S&F 3mm thick figured glass not exc 0.50 sqm each pane and fixed with oil putty or with wooden beading in square etc complete all as specified and directed.

S&F towel rail 20mm dia of chromium plated, fixed with and including chromium plated brass screws and wooden /plastic cleats complete all as specified and directed.

S&F vitreous china squatting pan "Orissa pattern", size 580x 440mm, white with integral foot rest (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F PVC valveless, symphonic action type flushing cistern, 10 ltr capacity, low level, white with inlet ball valve, float and handle including bracket complete all as specified and directed.

S&F flush pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern complete all as specified and directed.

S&F vitreous china urinals, half stall type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed.

S&F 15mm bore chromium plated urinal spreader for urinals complete all as specified and directed.

S&F vitreous china wash basin with pedestal of size 550x400mm including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

S&F PVC connection of 15mm size, 450mm long with PTMT nuts on both side complete all as specified and directed.

S&F waste fittings 32mm dia, brass, chromium plated for glazed ware sink, basins, etc with long screwed shanks and fly-nuts, flanged end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank of 500 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F 20mm dia ball brass valve, high pressure with polythene float and fly nut complete screwed for iron pipe complete all as specified and directed.

S&F 15mm bore bib taps, fancy type, chromium plated, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F 15mm dia pillar cock, fancy type, cast copper alloy, chromium plated complete all as specified and directed.

S&F 15mm bore stop cock, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed.

S&F 15mm bore GI tubing 'medium grade' with all fittings and fixed to wall and ceiling or laid in floor complete all as specified and directed.

All as per item No 120 but 20mm bore complete all as specified and directed.

S&F PVC (SWR) pipes 110mm dia, single socketed in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S&F PVC (SWR) pipes of 75mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

Cutting existing steel tubing for alterations or additions (Each cut measured) complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good to surfaces & applying two coats of white wash, cutting not exc 10cm girth complete all as specified and directed.

M&L for writing letters or figures (Block, Roman, Italic or Indian) not exc 30 cm height complete all as specified and directed.

NOTE:- SCHEDULE OF CREDIT (Amount shall be deducted offline from the total quoted amount to workout the net contract sum to be considered for acceptance.) [(-) Rs.39,371.00]

M/s B S Jain

M/s M.G. Hargunani

Bidder Name

North India Pest Control

M/s B S Jain

M/s M.G. Hargunani