REPAIR MAINT OF INTERNAL ELECTRIFICATION INCLUDING FANS AND GEYSERS AT CADETS LIVING ACCN AT NDA KHADAKWASLA

Amount

Repair / maintenance of internal light fitting of any type like tube lights / wall bracket light fittings / ceiling lights / mirror lights/ table lamp lights in its position, testing all the compenents / parts, wiring etc, identifying and replacing the defective components like driver, side holders, holders, Table lamps etc all as directed by Engr-in-charge. Note: (i) The rate against the above mentioned item is deemed for cost of labour only. (ii) Cost of spares like lamp holder, connector, connection wire, capacitor etc. replaced against above mentioned item will be measured & paid for separately under respective items of Sch 'A' here-in-below as supply only. (iii) The contractor's representative will report to concerned JE E/M at 0900hrs daily to collect the list of defects and will submit the completion report on following day before 0900hrs to the JE E/M. (iv) The contractor has to rectify the defects and make the light fittings functional within 24 hours from the time the list of defective lights is handed over to him / his rep by the concerned JE E/M. In case the light fitting is not made functional for whatsoever reason within the specified time limit, an amount of Rs 100/- per such defective light fitting per day will be recovered from the amount due to him through RAR / Final Bill. The repair/maint in Cadets living accommodation (Sqn bldgs) shall be carried out as per the timings convenient to cadets or as directed by Engineer-in-charge and preferably during afternoon and study period. The contractor shall engage separate team of technicians / repairer for each Battalion. (v) The contractor shall maintain proper record of repair / maint in a binded register duly bringing out the details of spares replaced on each and every light fitting and get it authenticated from concerned JE E/M on daily basis. The contractor shall put up the maint record register to Engineer-in-charge for inspection every Monday or as and when asked for. (vi) The contractor shall maintain sufficient stock of spares / material required for repair / maint of light fittings with the concerned JE E/M. (vii) The Electricians should be ITI (Electrical) qualified and the contractor should submit the copy of certificates of electricians while sigining the site orders.

Supply only of Retrofit pendant lamp holders/PVC / polycarbonate Angle/Batten type lamp holders retrofit type all as specified and directed.

Supply only High glow 9 W,warm white , LED bulbs B22/E27 base cap all as specified and directed.

Supply only High glow 3W, warm white , LED bulbs of B22/E27 base cap all as specified and directed.

S&F in replacement of fan regulator electronic step type suitable for 1200/1400 mm sweep fan as per the sample provided all as specified and directed.

S&F in replacement of switch piano flush type 5 Amps SP one way a all as specified and directed.

S&F in replacement of switch piano flush type 20 Amps SP one way all as specified and directed.

S&F in replacement of socket outlet 3 pin 5A flush type complete all as specified and directed.

S&F in replacement of socket outlet 2 in 1 3 pin 5 and 15 Amp flush type complete all as specified and directed.

S&F in replacement for ceiling rose, 3 terminals /PVC/Polycarbonate, isolated body. all as specified and directed.

S&F in replacement of modular switch 1 way 10 A 1 module. all as specified and directed.

S&F in replacement of modular switch 1 way 20 A 1 module with neon indicator all as specified and directed.

S&F in replacement for modular switch 2 way 10 A 1 module all as specified and directed.

S&F in replacement of 1 and 2 module Blanking plates all as specified and directed.

S&F in replacement of Modular socket 6 A 2/3 Pin 2 module all as specified and directed.

S&F in replacement of Modular socket 6A/16A - 2/3 Pin 2 Module all as specified and directed.

S&F in replacement of modular fan regulator, 2 module, suitable for ceiling fan of 1200/1400mm sweep all as specified and directed.

S&F in replacement of modular switch 1 way 10 A 1 module Bell switch 10A all as specified and directed.

S&F in replacement of door bell AC 230 volts single phase ding dong type all as specified and directed.

S&F in replacement for white cover plate with frame 18 module all as specified and directed. .Make:As per the sample given

S&F in replacement for white cover plate with frame 16 module all as specified and directed. .Make:As per the sample given

S&F in replacement for white cover plate with frame 12 module all as specified and directed. .Make:As per the sample given

S&F in replacement for white cover plate with frame 8 module all as specified and directed. .Make:As per the sample given

S&F in replacement for white cover plate with frame 6 module all as specified and directed. Make:As per the sample given

S&F in replacement for white cover plate with frame 4 module all as specified and directed. .Make:As per the sample given

S&F in replacement for white cover plate with frame 3 module.all as specified and directed Make:As per the sample given

S&F in replacement for white cover plate with frame 2 module all as specified and directed. Make:As per the sample given

S&F in replacement for white cover plate with frame 1 module all as specified and directed. Make:As per the sample given

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 18 module all as specified and directed.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 16 module all as specified and directed.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 12 module all as specified and directed.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 8 module all as specified and directed.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 6 module all as specified and directed.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 4 module all as specified and directed.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 3 module all as specified and directed.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 2 module all as specified and directed.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 1 module all as specified and directed.

M&L for securing loose wiring and repair to point wiring with necessary rigid non metalic PVC conduit/casing caping double lock type ISI marked inclusive all accessories complete all as specified and directed.

Taking down exiting copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed

M&L point wiring with 1.5 sq mm copper conductor FRLS (multistrand) PVC insulated ISI marked unseathed cable and including surface, Non metalic rigid PVC casing capping double lock type ISI marked not less than 25 mm with all fitting & other accessories and also including PVC insulated ISI marked unseathed FRLS cable size 1.5 sq mm copper conductor as earth wire to common earth dolly including PVC box suitable for modular type switches, sockets, fan regulator etc for following :- One light/Fan point controlled by one way switch 6 Amps 240 volts complete all as specified and directed

Ditto as per item No 40 above but One 3 pin 6 Amps socket out let point on independent board complete all as specified and directed .

Ditto as per item No 40 above but One 3 pin 6 Amps socket out let point on same board complete all as specified and directed .

Ditto as per item No 40 above but One light point controlled by two 6 Amp two way switches complete all as specified and directed .

M&L point wiring for one 3 pin socket outlet 15 Amp Independent with with 2.5 sq mm copper conductor FRLS (multistrand) PVC insulated ISI marked unseathed cable and including surface, Non metalic rigid PVC casing capping double lock type ISI marked not less than 25 mm with all fitting & other accessories and also including PVC insulated ISI marked unseathed FRLS cable size 2.5 sq mm copper conductor as earth wire to common earth dolly including PVC box suitable for 15 Amps socket outlet power point independent circuit complete all as specified and directed

Taking down exiting copper/aluminium sub main wiring complete for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed

M&L Sub main wiring with PVC insulated FRLS grade cable LT 1100 Volts grade PVC insulated unsheathed, multistranded with stranded copper conductor drawn through & including surface type PVC casing & caping of not less than 25 mm including drawn on wall/ceiling/through stair case/wooden surface with all accessories and incl cutting of existing surfaces of any type and making good to match with the existing surfaces acrylic sheet work after completion alongwith one contineous earth wire and connected to common earth complete all as specified for following sizes of cable :- (a) 2 x 2.5 sq mm with one continuous earth wire of size 2.5 sq mm Note : 2 runs of 2.5 sq mm cable and one run of 2.5 sq mm earth wire and PVC casing/capping will be measured as one meter.

(b)Ditto as per item no 46 above but 2 x 4 sq mm with one continuous earth wire of size 4.0 sq mm Note : 2 runs of 4 sq mm cable and one run of 4.0 sq mm earth wire and PVC casing/capping will be measured as one meter.

(c)Ditto as per item no 46 above but 2 x 6 sq mm with one continuous earth wire of size 6.0 sq mm Note : 2 runs of 6 sq mm cable and one run of 6 sq mm earth wire and PVC casing/capping will be measured as one meter.

S&F in replacement of MCB DB 2 way SPN single door sheet metal enclosure factory made suitable for MCB DB's 240 volts,concealed/surface in wall complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site complete all as specified and directed . Note - MCBs will be measured & paid separately under respective item of sch A, if required to be replaced.

S&F in replacement of MCB DB 4 way SPN Double door sheet metal enclosure factory made suitable for MCB DB's 240 volts,concealed in wall complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site complete all as specified and directed Note - MCBs will be measured & paid separately under respective item of sch A, if required to be replaced.

S&F in replacement of MCB DB 8 way SPN Double door sheet metal enclosure factory made suitable for MCB DB's 240 volts,concealed in wall complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site complete all as specified and directed . Note - MCBs will be measured & paid separately under respective item of sch A, if required to be replaced.

S&F in replacement of MCB DB 12 way SPN Double door sheet metal enclosure factory made suitable for MCB DB's 240 volts,concealed in wall complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site complete all as specified and directed Note - MCBs will be measured & paid separately under respective item of sch A, if required to be replaced.

S&F in replacement of factory made epoxy powder coated Distribution Board TP & N 4 way double door (VTPN MCCB DB) MCCB as In comer, and MCB as outgoing with metal door (IP-43 protection) fabricated from CRCA sheet and fixed semi flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockout semi flush to wall and making good disturbed surface and touch up with the same finishes complete all as specified Note: MCCBs and MCBs will be measured and paid seperately

S&F in replacement of MCB single pole 6-32 Amps working on 240 volts, 50 HZ AC, 10 KA 'B' curve all as specified and directed.

S&F in replacement of MCB DP 6-32 Amps working on 240 volts, 50 HZ AC, 10 KA 'C' curve all as specified and directed.

S&F in replacement of MCB SPN 40- 63 Amps working on 240 volts, 50 HZ AC, 10 KA 'B' curve all as specified and directed.

S&F in replacement of MCB TP 40-63 Amps working on 415 volts, 50 HZ AC, 10 KA , 'B' curve all as specified and directed.

S&F in replacement of MCB TPN 40-63 Amps working on 415 volts, 50 HZ AC, 10 KA , 'B' curve all as specified and directed.

S&F in replacement of MCCB with rating of 100 Amps,415Volts 3pole with 16kA breaking capacity,thermal magnetic asdjustable of overload & short circuit release as per IS-13947 & IEC 60947-2 & the service short circuit breaking capacity (Ics) should be equal to ultimate breaking capcity(Icu).MCCB should be with suitable spreaders and phase barriers for each terminals all as specified and directed. .

S&F in replacement of MCCB with rating of 150 Amps,415Volts 3pole with 16kA breaking capacity,thermal magnetic asdjustable of overload & short circuit release as per IS-13947 & IEC 60947-2 & the service short circuit breaking capacity (Ics) should be equal to ultimate breaking capcity(Icu).MCCB should be with suitable spreaders and phase barriers for each terminals all as specified and directed.

M&L in replacement of earthing complete with galvanised steel earth plate electrode 600x600x6.3mm thick, burried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia of minimum 15m length by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 in SSR PART-I connected to earthing test point all as specified or indicated including provision of earthing lead protection pipe, PCC earth pit with cover, excavation & earth work, testing on completion etc complete all as specified and directed.

M & L in replacement of Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified and directed.

Taking down ceiling fan/Exhaust fan/wall mounted fan/Pedestal fan/Airculator Fan/ of any sweep for servicing / repairing / maintenance, opening up, identifying and replacing the defective parts, cleaning, greasing,etc, reassembling and hanging up/fixing back at its original position, connecting up and testing complete all as specified and directed. Note : Cost of spares such as capacitors, bearings etc shall be measured and paid for separately under respective Item of sch A as supply only.

Supply only aluminium fan blade for exhaust fan of any sweep/make as per the sample given complete all as specified and directed.

Supply only bearing No.6201/6202/6203/6204 or any other No matching to the existing size and suitable for Exhaust fan/wall mounted fan/Pedestal fan/Airculator Fan/ of approved make complete all as specified and directed.

Supply only capacitor of 1.5 mfd for wall fans complete all as specified and directed.. Make: Epcos/Tibcon/Crompton

Supply only capacitor of 2.5 mfd for ceiling fan/exhaust fan complete all as specified and directed. Make: Epcos/Tibcon/Crompton

Disconnecting electric connection and removing the burnt winding of fan motor of Air circulator fans/Pedastal fans/Exhaust fan of size 600/450 mm sweep wall mounting Oscillating type and rewinding with super enarneled copper winding wire of suitable gauge or of matching size to the exisiting wires including all insulating material such as insulation paper sleeve, tape, varnishing etc and reassembling, testing, transporting back to site and refixing to original position complete all as specified and directed

Ditto as per item no.68 above but Wall mounted fans size 350/400 mm sweep Oscillating.

Ditto as per item no 68 above but Exhaust fan of 225/300/380 mm sweep.

M&L for Preparation of old surface of exhaust fan of any sweep by removing old paint using paint remover or by burning off using blow lamp and cleaning with cloth and Spray painting complete exhaust fan with superior quality synthetic enamel paint (Smoke gray) after applying primer complete all as specified and directed.

Dittto all as per item no.71 above but Air circulator/Pedestal of size 450/600 mm sweep with superior quality enamel paint (Grey) complete all as specified and directed

Disconnecting and taking down existing userviceable geyser of 100/50/25 ltrs capacity, taking it to civil workshop for repairing.Opening the geyser and dismanting all parts and taking out inner tank/container, removing dents making to shape including welding / brazing the leakage portion, filling the portion between inner tank and out casing of geyser with new glass wool heat insulating material . Reassembling and painting the outer casing of geyser with two coats of superior quality synthetic enamel paint(existing colors) and re- fixing to original place complete all as specified and directed

M&L in replacement safety valve(dead weight) suitable for geyser of 100 ltrs capacity of any type and brand of geyser complete all as specified and directed.

M&L in replacement thermostat 0-70ºC suitable for geyser of 100 ltrs capacity of any type and brand of geyser. Make:As per the sample given complete all as specified and directed

M&L in replacement heating element of capacity 3 KW,ISI marked of any type and shape suitable for 100 ltrs capacity geysers of any brand / make. Make:As per the sample given complete all as specified and directed

M&L in replacement heating element of capacity 2 KW,ISI marked of any type and shape suitable for 50/25 ltrs capacity geysers of any brand / make. Make:As per the sample given complete all as specified and directed

M&L in replacement heating element of capacity 3 KW,ISI marked of any type and shape suitable for solar water heater system of any brand / make complete all as specified and directed.

M&L in replacement flow unit (inner pipe assembly) suitable for geyser of 100/50/25 ltrs capacity vertical type of any geyser brand including rubber ring/gasket complete all as specified and directed .

Supply and fix in replacement GI mesh hot water connection 900 mm long including necessary washers suitable for geysers of various capacities complete all as specified and directed.

Supply and fix in replacement sheet metal enclosures Single pole MCB 20 Amps with a two pin and earth plug and socket complete with all accessaries etc complete all as specified and directed

Supply & fix in replacement neon lamp indicator square/round type complete all as specified and directed.

Supply and fix in replacement metal clad plug top 3 pin, 20 amps, ISI marked heavy duty complete all as specified and directed

Supply and fix in replacement metal clad socket 3 pin, 20 amps, ISI marked heavy duty complete all as specified and directed

S&F in replacement plug top 3 pin, 15/16 amps, 230 volts, ISI marked complete all as specified and directed

S&F in replacement plug top 3 pin, 5 amps, 230 volts, ISI marked complete all as specified and directed

M&L in replacement of ply wood sheet of 10 mm thickness for Exhaust fans and cutting to the size as required at the site including fixing the same with necessary nuts and bolt arrangement complete all as specified and directed

M&L for repalcing the down rod of ceiling fans with 5 feet GI ceiling fan hanging down rod with necessary clamp accessories complete all as specified and directed

M&L in replacement of acrylic sheet of 4mm thickness cutting to the size as required at the site including fixing the same with necessary screw arrangement complete all as specified and directed.

S&F in replacement PVC insulated cable 2 core stranded copper conductor 0.5 sqmm all as specified and directed

S&F in replacement PVC insulated cable 2 core stranded copper conductor 1 sqmm all as specified and directed

Supply & Fix in replacement PVC insulated round cable 3 core stranded copper conductor 2.5 sqmm as in connection cord of the geyser complete all as specified and directed

S&F in replacement of PVC insulated cable 3 core stranded copper conductor 4 sqmm all as specified and directed

S&F in replacement of PVC insulated aluminium conductor two core round cable 4 sqmm, ISI marked complete all as specified and directed

S&F in replacement of PVC insulated aluminium conductor two core round cable 6 sqmm, ISI marked complete all as specified and directed

S&F in replacement of 20 watt,3 in1, 230V surface and wall mounted LED batten, extruded aluminium housing with polycarbonate diffuser and integrated electronic driver including connecting up with twin core twisted flexible copper condctor cable from ceiling rose complete all as specified and directed Make- Luker LT20PR 3-in-1 or equivalent in makes as mentioned at makes list in PS

S&F in replacement of 10W,230V, LED batten suitable for indoor application of color temperature 6000K surface /wall mounted LED batten including connecting up with twin core twisted flexible copper conductor cable from ceiling rose complete all as specified and directed

S&F in replacement of surface mounted LED Panel lights size of 600mm x 600MM x 35mm 40 W LED 5700K, 240Volts and glare free symmetrical illumination suitable for ceiling, Environmental friendly, new generation, energy saving, high power LED as a light source with clear diffuser and separate replaceable electronic driver including connecting with twin core wire and also matching to the adjacent ceiling surfaces carefully all as specified and directed. Make:Luker Cat part No. LNPSRS40 or equivalent in makes as mentioned at makes list in PS Note: The quoted price shall include the cost of Light and its driver.

S&F in replacement of 12 watt, 230V surface surface LED COB Light-Tiltable and integrated electronic driver including connecting up with twin core twisted flexible copper condctor cable from ceiling rose including surface PVC box of circular/square type complete all as specified and directed Make- Luker LCOBSP12 or equivalent in makes as mentioned at makes list in PS

S&F in replacement of recess round type LED ceiling lights 15 W LED with ceiling cut out of Ø 135 mm, 6000K Environmental friendly, energy saving, recess mounted downlighter with electronic driver including connecting with twin core wire, including cutting the existing false ceiling dia to the required size and also matching to the adjacent false ceiling surfaces carefully all as specified and directed. Make: Luker cat part no. LDR20 or equivalent in makes as mentioned at makes list in PS

S&F in replacement of surface square type LED ceiling lights 15 W LED , 6000K Environmental friendly, energy saving, recess mounted downlighter with electronic driver including connecting with twin core wire, including cutting the existing false ceiling dia to the required size and also matching to the adjacent false ceiling surfaces carefully all as specified and directed.

S & F in replacement of 15 watts/m linear flex in colour white/warm white, with separate electronic drivers of suiatble and IP 65 protection complete ,Single phase, with aluminium profile including mounting on the ceiling as reqd at the site complete all as specified and directed

S&F in replacement of surface Decorative hanging light LED 30W, surface mounting, dome shaped pendant in green & black finishes including connecting with twin core wire, including cutting the existing false ceiling dia to the required size and also matching to the adjacent false ceiling surfaces carefully all as specified and directed.

Decorative wall light fixture made up of Polycarbonate, with 9 W retrofit LED Lamp B22 base including connecting with twin core wire, including cutting the existing false ceiling dia to the required size and also matching to the adjacent false ceiling surfaces carefully all as specified and directed.

S&F in replacement LED building security Sensor light fiitting 24 W, IP-65 protection made up of die cast alluminium housing with high power LED as lighting source and lens embeded PC cover having seperate driver compartment complete fixing with GI bracket made out of suitable GI pipe light grade suitable length bend to shape and fixed to pole/wall with necessary MS clamp accessories complete all as specified and directed Make- Luker LST-24SEN or equivalent in makes as mentioned at makes list in PS

S&F in replacement of GI pipe bracket of 25 mm dia 1 mtr long bend to shape for street light fitting made out of 25 mm dia GI light grade pipe fixed on pole using suitable FI clamp including necessary new nut, bolt and washer complete all as specified and directed.

Material and labour of Aluminum composite panel sheets (ACP Cladding ) including 1/1.5mm aluminium pipe including necessary harware such as drilling iron screws, double tape, silicon dow, masking tape etc complete all as specified and directed

SONU ENTERPRISES (BID ID -3103672)

M/S. M.A. Sharief engineers and contractors (BID ID -3115927)

Star Electrical (BID ID -3117368)

Sneha Aircool (BID ID -3113560)