PROVN OF B/R AND E/M WORKS AT TRADE OWNED KERB SIDE PUMP IN NIWARU JAIPUR MIL STATION

Amount

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation, etc or for shaft, well, cesspit, manhole, pier holes etc. not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out any type of soil etc complete all as specified and directed.

M&L cement concrete in foundations, filling and mass concrete type D2, (1:4:8) using 40 mm graded aggregate. etc complete all as specified and directed.

Returning filling with earth obtained from excavation including spreading watering and consolidation in layers not exceeding 25 cm thick etc. complete all as specified & directed.

Earth filling under floors including spreading, levelling, watering and well ramming in layers not exc 25 cm thick etc. complete all as specified & directed. Note:- Soil obtained from excavation under item 1 here-in-before shall be used for filling

Removing excavated surplus soil to a distance not exceeding 50 metre and depositing where directed at level not exceeding 1.5 metre above the starting point etc. complete all as specified & directed.

Brickwork with subclass `B' bricks, old size straight or curved on plan exc 6m mean radius, built in CM 1:6 etc. complete all as specified & directed.

M& L for Damp proof course 40 mm thick in cement concrete 1:2:4 Type B-0 to horizontal or vertical surfaces including necessary formwork etc. complete all as specified & directed.

Supply only Integral waterproofing compound etc. complete all as specified & directed.

M&L rendering 15mm thick on stone masonry surfaces or surface other than fair faces of brick work on wall in CM (1:6) finished even and smooth without using extra cement etc complete all as specified and directed.

M&L for rendering 10mm thick on brick masonry or concrete surfaces on wall in CM (1:6) finished even and smooth without using extra cement etc complete all as specified and directed.

M&L for rendering 5 mm thick in CM (1:3) on ceiling/ceiling patches finished even and fair without using extra cement etc complete all as specified and directed.

M&L for 75 mm thick cement concrete (1:4:8) type D2 using 40mm graded aggregate as in sub base etc complete all as specified and directed.

M&L for 25mm thick cement concrete (1:2:4) type B-0, using 12.50mm graded aggregate in sub floors, sub base floors and paving. etc complete all as specified & directed.

M&L non skid ceramic tiles (coloured) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including providing 15mm thick screed bed in CM (1:4) etc complete all as specified and directed.

S&F joint free coloured glazed ceramic tiles in vertical surface 200x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match etc. complete all as specified and directed.

M&L for 18-22 mm thick machine cut kota stone slab as in window cill, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grooving, rubbing and polishing etc complete all as specified & as directed.

M&L 75 mm thick cement concrete (1:3:6) type C-2 using 40mm graded stone aggregates as in floor/plinth protections finished even and fair without using extra cement etc complete all as specified & as directed.

M&L for reinforced cement concrete (M-25)(Design Mix) (20 mm graded stone aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc complete all as specified & as directed.

M&L for reinforced cement concrete (M-25) (Design mix) (20 mm graded stone aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span etc. complete all as specified & as directed.

M&L for reinforced cement concrete (M-25) (Design mix) (20 mm graded stone aggregate) in Columns, pillars, piers, posts and struts etc. complete all as specified & as directed.

M&L for reinforced cement concrete (M-25) (Design mix) (20 mm graded stone aggregate) in slab supported on walls, beams and columns in floors, roofs, shelves and the like etc. complete all as specified & as directed. Note:- Reinforcement & formwork shall be measured and paid for separately under respective items.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc. complete all as specified & as directed.

M& L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions etc. complete all as specified & as directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchibg, girders, bressummers, lintels, cantilevers, shelves, including susports, overhanges also splays between floors and beam etc. complete all as specified & as directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for fair finished flat surfaces of concrete etc. complete all as specified & as directed.

M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as per specified and directed.

M&L for Mild steel TMT bars 5 mm dia and over, cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc. complete all as per specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper of approved shade/tint over a coat of alkali resistance primer etc complete all as specified and directed.

M&L for preparation of newly plastered surfaces & applying two coats of white wash duly mixed with fevicol @ rate of 1Kg/1Ltr with 20 Kg of white lime on ceilings etc complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of wheather proof exterior emulsion paint over a coat of primer etc complete all as specified and directed.

S&F Pressed steel frames for doors size 150mm X 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia thresh old bar and filling hollow of frame with plain cement concrete Type C-0, 1:3:6 (using 12.5 mm graded crushed stone aggregate) etc. complete all as specified and directed.

S&F 30 mm thick, flush shutters, solid core construction, with block board and plywood face panels, commercial typr on both sides and both faces is covered with approved pattern decorative coloured laminate type 1 of 0.9mm thick and all around side faces is covered with decorative lipping etc. complete all as specified and directed

Anodised aluminium frame powder coated (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed

S&F anodised aluminium powder coating of any colour (thickness or power coating not less than 50 micron) window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed.

S&F framed work such as grills, gratings, etc, with ends of bars shouldered and / or riveted, or forged into spikes ; framed guard bars ; barred iron doors ; ladders; framed balusters; walkways ; railings ; framework of water tanks and similar work conforming to Fe-290 Gde E-165 etc complete all as specified and directed.

S&F for stainless steel cloth 0.56mm nominal dia of wire and 1.18mm average aperture and fixed with stain less steel wire staples etc complete all as specified and directed.

S&F for 5mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane etc complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer etc complete all as specified and as directed.

M&L for preparing new wooden surfaces of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer etc complete all as specified and directed.

S&F aluminium anodised barrel tower bolt 200 mm, extruded section. etc complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy etc. complete all as specified and directed.

M&L for Priming surfaces and applying normal treatment (for moderate conditions) using glass fibre base bitumen felt, grade with a layer of APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified. Application of polymeric membrane shall be done by torch application all as per manufacturer instructions.

M&L for treating the bottom and sides of excavation with ATT @ 5 litres of emulsion per square metre of surface area.

M&L for treating the top surface of filled earth with ATT @ 5 litres of emulsion per square metre of surface.

Provision of fire point as per TD Drawing No CEJZ/TD/2004/43/ sheet No 1/1 dated 08 Apr 2004 and complete all as specified and directed

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil etc complete all as specified and directed.

Excavating over areas, not exceeding 1.5 m deep and getting out soft / loose soil etc complete all as specified and directed.

Forming embankments including raising (or lowering) earth, spreading in layers n exc. 30cm thick; watering, ramming/rolling and finishing to required size, shape, etc., n exc. 1.5m high from base etc complete all as specified and directed.

Removal of excavated material exceeding 250m but not exceeding 500m and depositing where directed at a level not exceeding 1.5 m above the starting point .etc complete all as specified & directed.

Rolling and consolidating formation surfaces in cutting Power roller exceeding 8 tonne & not exceeding 12 tonne all as specified and directed.

M&L for Soling (or sub base) with broken boulders or quarried stone, inter stices filled, surface formed and rolled and consolidated to required gradient and camber

M&L for 150 mm thick WMM, providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub base/base course on well prepared sub base and compacting with smooth wheel roller of 80KN to 100KN weight to achieve the desired density etc complete all as specified and directed

M&L 100 mm thick cement concrete type D2, (1:4:8) using 40 mm graded aggregate as in sub base etc complete all as specified and directed.

Supply and laying sand filling under floors or in foundation cushing to paver block including watering and consolidation etc complete all as specified and directed.

M&L for Polythene film, black, 50 micron laid in floors etc complete all as specified and directed.

M&L for 150 mm thick Cement concrete work in pavement/hard standing of flexural strength 40kg/per sq cm in field using 400 kg Cement per cubic metre etc complete all as specified and directed.

M&L for Forming Contraction (Dummy) joints Grade ‘A’ 65mm deep x 10mm wide, filled with sealing compound etc complete all as specified and directed.

M&L for Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ etc complete all as specified and directed.

M&L for Finishing surface of concrete roads, pavements, by belting etc complete all as specified and directed.

M&L for hardcore of broken stone or boulders, gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface etc complete all as specified and directed.

M&L for Pre-cast Cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in kerb stone including setting in CM 1:6 etc complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block, 80mm thickness, M-40 grade of any shape and size confirming to IS-15658-2006, with grey cement and pigment laid over etc complete all as specified & directed.

M&L for cement concrete type D2, (1:4:8) using 40 mm graded aggregate as in foundations, filling and mass concrete etc complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in coping, bed plates, kerbs including weathering, slightly rounded or champhered angles and throating etc complete all as specified and directed.

M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide etc complete all as specified and directed.

M&L for 50 mm thick PCC (1:2:4) type B-1. using 20mm graded stone aggregate as in paving/beds for culvert finish even and smooth without using extra cement etc complete all as specified and directed.

M&L for rendering 15mm thick on brick masonry surfaces or surface other than fair faces of brick work on wall CM (1:4) on walls finished even and fair without using extra cement etc complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc complete all as specified & directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surface in CM 1:3 mixed with WPC, Finished even and smooth without using extra cement etc complete all as specified & directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surface in CM 1:3 on external surface etc. complete all as specified & directed.

Supply only integral water proofing compound complete all as specified & directed.

M&L for RCC M-25 (20 mm graded stone aggregate) as in precast manhole cover slab including necessary form work etc. complete all as specified & directed.

M&L for PCC 1:2:4 type B1 (using 20 mm graded stone aggregate as in surface channel of and drains etc. complete all as specified & directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc (Inner girth only to be measured for payment) etc. complete all as specified & directed.

Add or deduct from ser item 6 above for each 25 mm girth or part there of over or under 30 cm etc. complete all as specified & directed. Note: - This item is only for adjustment of rates.

Supply and laying DWC pipes (Double wall corrugated) of class SN-4, IS-16098 (Part-II) of size internal dia of 150 mm, laid in trenches and jointed complete with coupler, bends, tee, reducers etc complete all as specified & directed. Make: Ultra plus DWC PE pipe of Supreme/Corfit of Prince/D-Rex DWC of Astral.

Cutting to existing manhole for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required (150 mm) bore etc complete all as specified & directed.

M&L for rendering 5 mm thick in CM 1:3 on brick wall or concrete surface, surface finished even and smooth without using extra cement etc. complete all as specified & directed.

M&L for preparation of newly plastered surface and applying two coats of Cement based paint over a coat of primer etc. complete all as specified and directed

Mild steel ROUND bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified & directed.

S&F steel gate Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165. portions framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc complete all as specified & directed.

Dismantling expanded metal, any thickness or mesh, fixed with steel or wood fillets, weight n exc 4 Kg per Sqm etc complete all as specified & directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground etc. complete all as specified & directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc. complete all as specified & directed.

Excavation in post holes each not exceeding 0.5 Cum getting out, in hard/dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m and making good surface etc. complete all as specified and directed.

M&L for MS Work (angle iron) as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 etc. complete all as specified and directed.

S&F Galvanised, 2 strand, steel barbed wire 2.24 mm dia, barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to fencing posts, any type of standard rails, straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, staples, or steel nibs, pins etc. complete all as specified and directed. Note:- each line of wire shall be measured and paid.

Fixing only chain link fencing including line wire, any mesh, size and to any type of standards, rails, straining bolts, etc including provision of galvanised iron binding wire etc. complete all as specified and directed. Note :- (i) Chain link fencing shall be measured and paid separately as supply only under respective item. (ii) Post and straining bolts shall be measured paid for separately under respective item.

Supply only chain link mild steel galvanised fencing any size or type gauge etc. complete all as specified and directed.

M&L for preparation of new steel surfaces of any description not exceeding 10cm width or girth girth when unconnected with other painting or when painted in a different tint and applying two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer etc complete all as specified and as directed.

S&F MCB distribution board, powder coated, CRCA steel sheet, degree of protection IP 42, IK-09 with reversible double door, recess mounted, having insulated 200 Amps tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required for the SPN, 240 volts, 4 ways 04 Nos. etc complete all as specified and directed

S&F MCBs of 'C' series SPN 32 Amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs etc complete all as specified and directed

S&F MCBs of 'C' series SP 5 to 32 Amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs etc complete all as specified and directed

Point wiring complete with 1.5 Sq mm, single core PVC insulated PVC unsheathed multi-stranded copper conductor FRLS cable 1100 volts grade laid/drawn through & including rigid PVC conduit with necessary conduit fittings/ accessories fixed concealed in walls/ceiling by means of PVC sleeve/dash fastener with cadmium plated iron screws all as per ISI including sunk type pressed steel terminal boxes for mounting, fittings like switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet top covers concealed in walls etc including 1.5 Sq mm single core PVC insulated but unsheathed multistranded copper conductor FRLS cable as continuous earth wire to common earth and connecting to earth dolly of following :-

(a) One light/fan/bell point controlled by one, one way switch.

(b) One 3 pin 5 Amp Socket outlet on the same board with other switches

(c) One 3 pin 5 Amp Socket outlet on independent board with other switches

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4.0 Sq mm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 Sq mm (Green) drawn into and including concealed rigid non-metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal box of thickness not less than 1 mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets as required for one 3 Pin 16 amp socket outlet point controlled by one switch on independent board.

S&F switch piano flush/bell push button single pole one way 5 Amp 230/250 volts etc. complete all as specified and directed.

S&F switch piano flush/bell push button single pole one way 15/16 Amp 230/250 volts etc. complete all as specified and directed.

S&F socket outlet multipurpose use, flush mounting 5 Pin 6 Amps 230/250 volts etc. complete all as specified and directed.

S&F socket outlet multipurpose use, flush mounting 6 Pin 16 Amps 230/250 volts etc. complete all as specified and directed.

S&F lamp holder, angle type with back plate suitable for batten fittings etc complete all as specified & directed.

S&F ceiling rose 6 amp, 3 Phase, 3 plates polycarbonate body etc. complete all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection etc. complete all as specified and directed.

Supply and fixing energy saving environmental friendly, LED Batten tube light fittings 18/20/22 watt, 1200 mm(4 feet)TL, long life impact proof, surface/ wall mounting IP 20, 100LM per watt, extruded thermoplastic body with PC diffuser greater than 120 degree wide distribution available in 6500K CCT with high brightness LEDs complete with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size including dismantling of old existing unserviceable fluorescent/ LED TL etc. complete all as specified and directed.

S&F stepped type electronic fan regulator 240V 50HZ, 100 Watts flush type (ISI marked) on the existing phenolic laminated sheet etc. complete all as specified and directed

Supply and fixing ceiling fans with blades, down rods, electronic regulator and accessories, 230V, 1200mm sweep, min air delivery 210CFM with service value 6.00 BEE five star rated with brushless direct current motor (BLDC) etc. complete all as specified and directed.

Supply and fix steel tubular swaged poles type 410SP-310 (9.0 meter long) complete with CI base plate and finial and Including foundation and coping including earth/PCC work for foundation etc. complete all as specified and directed.

S&F street light Luminaries 35/45 Watt LED, AC 230 volts, IP 65 degree protection, new generation saving & environmental friendly long life versatile powder coated pressure die cast aluminium luminaries with high power LED street light with heat resistance toughened glass with lens as light source complete including making connection with street light junction box and including bracket of GI pipe 40mm dia & wiring with PVC insulated 3 core copper cable of size 23/0.0076 including nut, bolts and washers etc. complete all as specified and directed. Make:-Wipro Cat Part No LR02-501-XXX-57-XX or equivalent in C&S, Phllips, Polycab.

M&L for factory made street/gate light junction box, single phase, 2 wire, 240 volts, weather proof pole mounted made out of 1.63 mm thick MS sheet of size 250x150x100mm depth, which shall be in accommodated with properly insulated R' Y' B & Neutral aluminium buses of 32 Amps rated current cap and including MCB SPN 6 Amps - 01 Nos, for connecting of street/gate light fittings, with hinged door and locking bolt, handle etc. complete all as specified and directed.

M&L earthing complete as per electrical plate No 3 of MES SSR Part-I with galvanised steel earth plate electrode 600 mmx600mmx6mm, buried directly vertically in ground in a pit depth not less than 2.25 metres below ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level connected to and including connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts check nuts and washers of galvanised iron or steel. Earthing strip shall be protected by galvanised iron or steel pipe 40 mm bore light grade and connected to continuous earth wire on pole / test point. Watering pipe shall be 20 mm bore GI medium grade. The earthing shall be of inclusive of excavation & earth work in any type of soil, charcoal, salt, funnel PCC pit and RCC cover etc. complete all as specified and directed. NOTE:- (i) The concrete pit shall be made in PCC 1:2:4 type B-O, using 12.00 mm graded crushed stone aggregate 40mm thick precast cover slab of RCC (1:2:4), type B-1, using 20mm graded crushed stone aggregate with suitable MS handle in lieu of CI cover. Reinforcement in cover shall be of 8mm dia TMT bars laid @150mm c/c both ways. (ii) Quoted shall include the cost of 7.5 metre GI pipe for protection of earth wire/strip. (iii) Quoted shall include cost of 7.5 metre earth lead wire/strip. (iv) Earth electrode shall be surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides.

M&L earthing complete as per electrical plate No 3 of MES SSR Part-I with galvanised steel earth plate electrode 600 mmx600mmx6mm, buried directly vertically in ground in a pit depth not less than 2.25 metres below ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level connected to and including galvanised iron or steel earth strip 32mm x 6mm by means of bolts, nuts check nuts and washers of galvanised iron or steel. Earthing strip shall be protected by galvanised iron or steel pipe 32mm bore light grade and connected to continuous earth wire on pole / test point. Watering pipe shall be 20 mm bore GI medium grade. The earthing shall be of inclusive of excavation & earth work in any type of soil, charcoal, salt, funnel PCC pit and RCC cover etc. complete all as specified and directed. NOTE:- (i) The concrete pit shall be made in PCC 1:2:4 type B-O, using 12.00 mm graded crushed stone aggregate 40mm thick precast cover slab of RCC (1:2:4), type B-1, using 20mm graded crushed stone aggregate with suitable MS handle in lieu of CI cover. Reinforcement in cover shall be of 8mm dia TMT bars laid @150mm c/c both ways. (ii) Quoted shall include the cost of 7.5 metre GI pipe for protection of earth wire/strip. (iii) Quoted shall include cost of 7.5 metre earth lead wire/strip. (iv) Earth electrode shall be surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides

Supply and laying of High density polyethylene pipes (HDPE) of 40mm dia, pressure rating 6 kgf/cm2 laid in trenches (from cabin room to KSB pump) etc. complete all as specified and directed.

Outgoing :- (i) MCCB 415 volts of capacity 40 Amps 16 KA, 4 pole - 02 Nos (Outgoing to LTP-2 & 1 spare) (ii) 3 ph LED multifunction metre CI 0.5 - 01 Set (iii) LED indicator lamp –01 Set (set of three) (iv) Cable Gland of size 70 Sqmm 3.5 Core - 03 Nos

(iv) All CTs and PTs shall be cast resin type. (v) All indicator lamps should be of LED type. (vi) The height of panel should be 0.60 mtr from ground level with PCC foundation and the cost for foundation is deemed to the quoted rate.

Supply, laying, connecting & testing of XLPE Insulated screened PVC bedded galvanized steel strip or wire armoured electric power, cable (heavy duty) with aluminium conductor, 1100 Volts grade cross sectional area 70 sqmm 3.5 core laying in trenches or passing through pipe etc. complete all as specified and directed.

Supply, laying, connecting & testing of XLPE Insulated screened PVC bedded galvanized steel strip or wire armoured electric power, cable (heavy duty) with aluminium conductor, 1100 Volts grade cross sectional area 25 sqmm 4 core laying in trenches or passing through pipe etc. complete all as specified and directed.

Supply, laying, connecting & testing of XLPE Insulated screened PVC bedded galvanized steel strip or wire armoured electric power, cable (heavy duty) with aluminium conductor, 1100 Volts grade cross sectional area 10 sqmm 2 core laying in trenches or passing through pipe etc. complete all as specified and directed.

Supply and install, testing and commissioning of silent Diesel Engine driven generating set above 10 KVA with AMF panel 415 volts, 3 phase 4 wire, engine as per IS: 10001/ 10002 and Alternator as per IS: 13364 complete with relay panel and switch gears with AMF panel for automatic starting on main failure control panel having meter and sound proof canopy as per CPCB norms and including necessary foundation earth work and PCC etc.complete all as specified and directed.

M&L for excavating in trenches exceeding 1.5m and not exceeding 3.0m wide for foundation of poles, laying of cables etc. not exceeding 10 Sqm area on plan and not exceeding 1.5 meters in depth and getting out in any type of soil etc. complete all as specified and directed.

M&L for concrete (1:3:6) type C-2 using 40mm graded crushed stone aggregate for foundation of poles/struts/sky assembly etc. complete all as specified and directed.

M&L for concrete (1:3:6) type C-1 using 20mm graded crushed stone aggregate for coping of poles/struts etc. complete all as specified and directed.

M&L for sand cushioning to underground cable screened washed river sand and punning for cushioning to cable all as directed.

Supplying and laying factory made un-reinforced PCC precast cable covers class LV, type I, peak, size 300mm x 180mm x 40mm complete all as specified and directed.

Supply & fixing or laying galvanised steel tubing light grade (ISI marked) 100mm bore for protection of underground cable on poles / walls under road crossing etc complete all as specified & directed.

Schedule of Credit

SAI MAX INFRAPROJECTS

J.J.ENGINEERING