PROVN OF SECURITY INFRASTRUCTURE AND ADDITION /ALTERATION OF EXISTING INFRASTRUCTURE INCLUDING ROAD AND CULVERT AT MEG CENTRE BANGALORE

Lumpsum price worked out by the tenderer for BUILDINGS / STRUCTURES as listed in Schedule ‘A’ Part-I

Lumpsum price worked out by the tenderer for INTERNAL WATER SUPPLY as listed in Schedule ‘A’ Part-II

Lumpsum price worked out by the tenderer for INTERNAL ELECTRIC SUPPLY as listed in Schedule ‘A’ Part-III

Lumpsum price worked out by the tenderer for ROAD/PATH/CULVERT & HARD STANDING as listed in Schedule ‘A’ Part-IV

Lumpsum price worked out by the tenderer for SEWAGE DISPOSAL as listed in Schedule ‘A’ Part-V

Lumpsum price worked out by the tenderer for AREA DRAINAGE as listed in Schedule ‘A’ Part-VI

Lumpsum price worked out by the tenderer for EXTERNAL WATER SUPPLY as listed in Schedule ‘A’ Part-VII

Lumpsum price worked out by the tenderer for EXTERNAL ELECTRIC SUPPLY as listed in Schedule ‘A’ Part-VIII

Lumpsum price worked out by the tenderer for SECURITY WALL /FENCING/GATE as listed in Schedule ‘A’ Part-IX

Lumpsum price worked out by the tenderer for as listed in Schedule ‘A’ DEMOLITION Part-X

Lumpsum price worked out by the tenderer for as listed in Schedule ‘A’ HOT WATER SUPPLY Part-XI

SCHEDULE 'A' PART XII (MISCELLANEOUS ITEMS) Note: This schedule is not pre-priced by MES

M&L for Point wiring complete with 1.5 sq mm single core PVC insulated FRLS unsheathed cable 1100 volts grade with multi stranded copper conductor confirming to IS-694 1990 wih ISI marked (for phase, neutral and earth) in and including stove enamelled Steel conduit with ISI Mark of minimum 20mm dia and all conduit accessories concealed including cutting/ chases in wall/ceiling/fixed to roof/truss/columns etc and including factory made branded make embossed glvanised steel pressed terminal boxes alongwith suitable size modular cover plates with frames for fixing modular switches and sockets, fan regulators etc. of suiable size modules and the earth wire to be connected to common earth dolly complete all as specified and directed for the following :- Note: Location of light points, 6 Amp socket points and light fittings may be decided by Engr-in-charge as per site/user requirment

One light point controlled by one modular switch 6A one way

One Ceiling/Exhaust fan point controlled by one modular switch 6A

One 3 pin socket out let 6 Amps on independent board

One 3 pin socket out let 6 A on same board

One light point controlled by two 2-way switches,

M&L for Point wiring complete all a specified with 1100 Volts grade 4 sq mm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor conforming to IS 694 1990 with ISI marked (for phase, neutral and earth)in and including stove enamelled Steel conduit ISI Mark of minimum size 20mm dia all accessories concealed including cutting/ chases in wall/ceiling/fixed to roof/truss/columns etc and including factory made branded make embossed galvanised steel pressed terminal boxes for fixing modular sockets of suitable size modules and the earth wire to be connected to common earty dolly all as specified and as directed.all as specified and as directed for One three pin modular switch socket 16 amps outlet on independent board

Supply and Fix Study Lamp 3 Watts single phase fixed on walls complete all as specified and directed

Supply & Laying of 150 mm internal dia DWC HDPE SN-8 pipes confirming to IS 14930 part 2/IS 16025 part-24, laying including all necessary specials, cutting and joining as specified and directed.

Construction of LLDPE Conventional Septic tank 05 users designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for

M & L for excavating the soil above pipe line at tapping point without damaging the pipeline, cutting of existing CI/DI pipe of 100 mm dia and inserting DI Tee of size 100x 100 x50 mm including necessary jointing accessories like rubber gaskets etc and connecting to 50 mm dia GI pipe with flanged joint, refilling the excavted sand all as specified and as directed.

M & L for excavating the soil above pipe line at tapping point without damaging the pipeline, cutting of existing CI/DI pipe of 80 mm dia and inserting DI Tee of size 80x 80 x 40 mm including necessary jointing accessories like rubber gaskets etc and connecting to 40 mm dia GI pipe with flanged joint, refilling the excavted sand all as specified and as directed.

M&L for construction of valve chamber 600x600x600 mm depth with PCC foundation in the ration 1:4:8 brick work cement mortar in the ratio 1:4 using of class B bricks , PCC coaping at the top of the ratio 1:2:4 , plastering 15 mm thick in the ratio 1:4 including MS sheet cover 3mm thick with angle iron frame 50x50x6mm locking arrengement complete with painting on steel surface with one coat of red oxide paint over two coats of synthetic enameeled paint all as specified and directed . (Earth work shall be measured and paid seperetely in the respective items)

Supply and fix double compression copper stainless steel gland for fixing armoured cable in panel of size 2 core 6 Sq mm to 16sq mm size

Supply and fix double compression copper stainless steel gland for fixing armoured cable in panel of size 4 core 25 Sq mm to 35 sq mm size

Supply and fix double compression copper stainless steel gland for fixing armoured cable in panel of size 3.5 core 75 Sq mm size

Supply and fix FRP pole box of size 200 x180x102 mm with hingedcc door, thermoplastic, polycabonate, IP-66 complete with and including 4 pole 32 A connector, Double compression glands-2 Nos of suitable size of cable, MCB SP 6 Amps, DIN rail, mounted on LT pole with GI clamps made out of MS Flat iron of size 25mm x 4 mm complete with nuts and bolts on street light pole all as specified

M & L for Earthing complete with galvanized steel earth plate electrode 60cmX60cmX6 mm thick buried in ground vertically to a depth not less than 2.25 metre below normal ground level, normal with top edge of earth plate not less than 1.5 metre below normal ground level, earth plate connected to a galvanized earth lead wire 4 mm dia as earthing lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of MES SSR Part-I (2009) connected to earth test point all as specified or indicated including testing on completion with and including 15 mm bore light grade GI protection pipe 7.5 meters long for earth including PCC 1:2:4 pit with pre cast RCC 1:2:4 type B1 cover 40 mm thick reinforced with 6mm dia MS bars @ 100mm both ways with lifting hook made out of 6mm dia MS bars watering arrangement with funnel wire, common salt and charcoal filling, necessary excavation and earth work in any type of soil complete all as specified.

Fabricate , Supply, install, test and commission LT feeder pillar cubical type, powder coated, outdoor type, fabricated with 3.15mm CRCA sheet mounted on 40x40x4mm MS angle mounted on PCC platform, with and including TPN aluminum bus bar of capacity 63 amps with PVC insulator supports, heat shrink sleeves for bus bar colour code complete with measuring instruments like multifunction meter, indication lamps and the following switch gear. (Street Light Panel) (i) Aluminum bus bar 3 phase & neutral of capacity 63 Amps (ii) MCCB 4P 40 amps 25 KA - 01 No (Incoming) (iii) MCB TPN pole 32 Amps 10 KA - 02 No ( Outgoing ) (iv) Duty Contactor TP 25 Amps,10KA - 02 Nos (v) Astronomical timer switch - 01 Nos (vi) Multifuncion meter & CTs with -/5A (vii) LED indication lamps

Fabricate , Supply, install, test and commission LT feeder pillar cubical type, Powder coated, outdoor type, fabricated with 3.15mm CRCA sheet mounted on 40x40x4mm MS angle, on PCC platform, with and including TPN aluminum bus bar of capacity 100 amps with pvc insulator supports, heat , heat shrink sleeves for bus bar colour code complete with measuring instruments like multifunction meter, indication lamps and the following switch gear for Loop-in & Loop-Out Box (i) Aluminum bus bar 3 phase & neutral of capacity 100 Amps (ii) MCB TPN 20 amps 10 KA - 01 No (Incoming) (iii) MCB TPN pole 16 Amps 10 KA - 04 No ( Outgoing ) (iv) Duty Contactor TPN pole 20 Amps 10 KA - 03No (v) Astronomical timer switch - 01 Nos (vi) LED phase indication lamp R,Y,B colour - 01 No

M & L for Earthing of machinery installed at substation using GI strip as earthing lead complete with galvanized steel earth plate electrode 60cmX60cmX6 mm thick buried in ground vertically to a depth not less than 2.25 metre below normal ground level, normal with top edge of earth plate not less than 1.5 metre below normal ground level, earth plate connected to a galvanized earth lead strip 32 x 6 mm dia as earthing lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of MES SSR Part-I (2009) connected to earth test point all as specified or indicated including excavation,earthwork,PCC pit,CI covers, funnel with watering pipe, wire mesh and testing on completion all as specified and as directed.

M/L for LT cable route indicators Oval Shaped 200x150x6 mm cast Iron precast with engraving "LT MES CABLE" embedded with PCC in mix 1:3:6 type C1 incl necessary exc,returning filling & removal of soil complete as directed

(A) Alternator :- Standard design alternator rated

S&F PVC coated 4mm dia galvanised steel wire, mesh aperture 76.20x12.70 mm square mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing

Supply and fixing concertina coil fencing with GI concertina coil of 600mm dia with coil thickness of 2.5-2.6mm and 0.5mm blade thickness fixed over 'Y' shaped angle iron with necessary GI staples, GI clips and bolts all complete as per per direction of Engineer-in-Charge. (Angle iron shall be paid separately)

Supply, installation, testing and commissioning of 10 KVA/ 8KW, (The capacity of Generator set shall be net after all due derating factors as per relevant lSI standard), silent Diesel engine Generating Set, 415 volts, 3 phase, 0.8 Power factor, 50 Hz, 4 wire system as per IS 10001/10002 comprising of KOEL 10 KVA or equivalent, developing 16 BHP @ 1500 RPM, Air Cooled, electric start coupled to alternator as per IS 13364 mounted on a common base frame with standard control panel for automatic starting on main control panel having meters, with emission control device to control the PM within range as prescribed by NGT/ norms published vde GSR 804(E) dt 03.11.2022 of GoI and updated till date on procurement and CPCB approved acoustic enclosure suitable for ambient condition at Bangalore with integral fuel tank with battery and leads and accessories complete iincluding required PCC foundation as per manufacturers instruction and confirming to conditions as per IS provisions:-

Material and labour for street light bracket made of 40mm GI pipe light grade 1.5 m length bent in shape for mounting street light on one end, fixing the bracket on pole with suitable GI clamps, Nuts and bolts all as specified and as directed.

(d) Exhaust System :- Exhaust System complete with exhaust piping of suitable dia as per manufacture standard with MS pipe light grade up to and away two meters height from top of enclosure including necessary angle iron frame supports from floor to the bottom of exhaust pipe from the enclosure covered with mineral wool of thickness 50mm rapped with chicken wire mesh of size 2.25mm and aluminum sheet of 24 SWG to be complete with in the enclosure for safe exhaust without transforming vibration to the wall of the enclosure.

(C) Fuel System :- Fuel injection system with fuel injectors, fuel injection solenoid switch/nozzles/ governor electronic type capable for 1 % speed /frequency regulation. (i) Fuel filters (ii) Fuel hoses (iii) Lub oil System :- (iv)Lubricating oil filter (v) Lubricating oil pump (vi) Air Intake System :- (a) Air intake Manifold (b) Air cleaner dry type (D) Governor :- Mechanical Governor (a) Starting System :- Electric Self starter with maintenance free batteries including battery charging alternator.

system (e) Fly wheel housing and fly wheel. (E) Generator Monitoring Panel: Comprising of following:- (a) Microprocessor based integrator generator set monitories, metering, protection and control system with built torque matched volts/H3 over load control. (b) Engine protection for low lub oil pressure, high coolant temperature (alarm & shutdown) (c) Alternator protection parameters like under voltage, over current, under frequency, over frequency ( alarm & shut down) (d) Relay drivers for remote annunciations

(iv) Handling and operation: Salient features of accessories shall be as under: (a) Radiator with blower fan (b) Corrosion inhibitor coolant (c) Paper element filters for fuel, lub oil and by pass. (d) Electronic governor controlled direct fuel injection

(l) Safety Controls : - Engine low lube oil pressure, high water temperature and over speeding of engine. (m) Coupling arrangement : - Flexible coupling, fly wheel to suit flexible coupling fly wheel housing. (n) Accessories :-A VM Pads built or separately mounted to manufacturer base frames. (o) Base Frame: - Made out of ISMC 200 of sturdy design made of MS channel with necessary reinforcement and predetermined holes. (p) Fuel Tank :- Daily service fuel tank of capacity suitable for 10 Hrs runin full load (Inbuilt) made out of 3mm thick (Heat Retardant) sheet top and bottom with calibrated level indicating arrangement, stop cock, drain plug, fuel pump of suitable capacity and connected pipe line should be installed with in built inside the acoustic enclosure is inclusive of the cost of DG Set and is as per manufacturer design.

(b) Batteries:- 1 No. Maintenance free Battery of suitable AH capacity complete with copper conductor multistranded leads of suitable length from self starter to the battery terminals complete with initial charge and initial fill of electrolite all as specified. Make:- EXIDE / AMRON / Produced by original DG set manufacturers (i) Starter gear ring (ii) Start and stop push button (iii) Ignition key / Switch

(i) 25 Amps, 4 pole contactor - 2 Nos. (ii) MCCB, 4 Pole 25 Amps, 25 KA-2 Nos for both supplies suitable fuse links. (iv) CTs 50/5A for both the supplies. (v) DC Ammeter. (vi) DC Voltmeter. (vii) Push buttons. (viii) Indication Lamps. (ix) 2 over load+ earth leakage relay. (x) Multi functional digital meter for KWH,KVA,KW,Amps,volts, frequency, power factor etc. (xi) SMPS Battery charger 12V, with trickle & Boost charging (xii) On/ Off switch. (xiii) Automatic/manual switch. (xiv) Hooter.

(e) Cyclic cranking (f) Auto/manual start stop (g) Alternator trim adjustment from the front key pad (h) Operates within a temperature range 0- 50°C and humidity up to 95% (j) Remote monitoring capability through separate interface modules (k) Genset metering parameters like lube oil pressure, coolant temperature, engine speed(rpm), run hours, DC voltage, 3 phase volts and 3 phase amperes, frequency, KW, KVA, power factor

(a) Custom built product for various equipments, with ensure the optimum performance without duration. (b) Rugged in construction maintenance free and modular designs which facilitate easy at site. (c) 16 SWG (1.6 mm) thick CRCA sheets to be used for enclosure panel to ensure longer life against weathering action. High quality acoustic insulation materials to be used as per IS 8183 for maximum sound absorption. Acoustic layers are supported by perforated sheets. (d) Sheet metal components of the enclosure should undergo various stages of surface treatment prior to painting which leads to be better life of the enclosure against weathering action.

(q) Deliverables:- Confirms the norms established by CPCB. (F) AMF PANEL:- (a) Auto Main Failure (AMF) panel made out of 2 mm thick CRCA sheet, powder coated of conforming to IS 8623 totally enclosed dust and vermin proof with front and rear openings of 415 Volts, 3 Phase,4 Wire, AC 50 Hz having aluminum bus bar capacity required to carry current at 100% load of 10 KVA DG set with three phase and half neutral color coded, prewired with copper flexible cable, be all as specified with the following accessories, control cable from Gen set to AMF panel:-

(l) Ducting if required, bellows, mechanical hardware like locks, hinges fasteners etc to be provided. (m) Deliverables. 75 dBA @ imtr at 75% load under free field conditions. The temp inside tee enclosure will be within as per manufacturers recommendations above ambient temp. (n) The enclosure should be provided with bulk head light fitting for inside illumination (o) The batteries should be placed inside the enclosure beside the DG Set on a suitable insulated platform. (p) The DG Set should be provided with external Emergency stop push button.

(xv) Voltage sensing relay. (xvi) Six window enunciator for fault indications. (xvii) Electro magnetic relays. (xviii) Metering required in DG set :- A, V, Hz, KVA, KW, PF & KWH Metering required in mains :- A, V, Hz. (G) Acoustic enclosure: CPCB approved enclosure is free standing floor mounted factory built and modular in construction to facilitate easy assembly at work site and will be drop over housing type. It will consist of acoustically treated panel housed in sheet steel will provide easy access for maintenance, repairs and operation. The enclosure is custom built to suit conditions, with the following features:-

(e) Special paint treatment with pure polyester powder/epoxy to be provided for better weather resistance. (f) Well designed ventilation system to be provided to pump up the heat in the chamber efficiently. (g) For effective acoustic / weather sealing a special type weather sealing gaskets, new frame rubber gaskets to be used. (h) Working space is to be provided around tube equipment for easy maintenance / repairs. (j) Necessary cut out provision for entry and exist of fuel lines cable to be incorporated in the enclosure as per the requirement. (k) A see through transparent window (glass or acrylic) in front of engine panel to be provided for monitoring the operation.

(H) Civil Works :- All civil works with PCC plat form and related to foundations including of panel and equipments and making good the existing structure of disturbed during installation and commissioning of Genset. The depth of the foundation shall be minimum 300 mm with ant vibration pads or as recommended by the manufacturer.

Earthing with galvanized steel earth plate electrode 60 cm x 60 cm x6 mm thick, buried directly in ground (earth pit not less than 2.25 metre below normal ground level) with top edge of earth plate not less than 1.5 metre below normal ground level connected to main earth lead GI strip 32 mmx6mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No 5 of MES Schedule Part I 1991, GI earth lead protected by GI pipe 40 mm dia light grade, providing and connected to earth test point with & including necessary excavation & earth works in any type of soil, returning filling, disposal of surplus soil to 50 metre, filing with mixture of charcoal and common salt up to 15 cm above top edge of earth plate, pit of PCC 1:2:4 with precast cover of RCC 1:2:4, watering arrangement with GI funnel, 20 mm dia GI light grade watering pipe, earth test point terminal block, commissioning & testing complete.