Construction of Community hall at Yarlok Chuchot Gongma (by way of Balance work(Under Capex)

Earth work in excavation by mechanical means (Hydraulic excavator) in foundation trenches or drains (not exceeding 1.5m in width or10sqm on plan), including dressing of sides and ramming of bottoms, lift upto1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Dumping stone in horizontall level including cost of stone and complete job

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with Cement mortar 1:6 (1 Cement : 6 coarse sand)

Providing & fixing upto floor five level precast cement concrete solid blocks including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete4.10.3 1:3:6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20 mm nominal

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

20 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Reinforced cement concrete work in walls (any thickness), including attached pilasters buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Providing and fixing square-mouth S.W. gully trap grade ‘A” complete with C.I. grating brick masonry chamber with water tight C.I.cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : a) 150 x 100 mm size P type. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Steel reinforcement for R.C.C.work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : Newwork (two or more coats) over and including water thinnable priming coat with cement primer

Providing and fixing traditionally carved wood work (Shingstak) over doors and windows including all accessories as per the direction of the Engineer in-charge, complete with; 2nd class kail wood

Applying priming coats with primer of approved brand and manufacture having low VOC (Volatile Organic Compound ) content. With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre

Centering and shuttering including strutting, propping etc. and removal of form work for : a) Foundations, footings, bases for columns

b) Suspended floors, roofs, landings, balconies and access platform

c) Columns, piers, abutments, pillars, posts and struts

Carriage of material from source to site including loading, unloading and stacking a) Cement and steel at an avg. lead of 08km

b) Sand an avg lead of 08 km

c) Aggregate an avg. lead of 08km

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately,all complete as per direction of Engineer-in-charge.(Note:-Butt hinges and necessary screws shall be paid separately) Second class kail wood 35 mm thick shutters

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. 1st Class Kail wood 35 mm thick

Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or gradedwoodparticleboard IS : 3087marked, to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately): 18 mm thick

Providing, fixing and applying Plaster of Paris (POP) false ceiling consisting of frame work made with 50mm sq M.S. tubes of 18 G thickness as main runner at 600 mm c/c both ways, suspended/supported with M.S. flats 25x4 mm from existing R.C.C. slab, finished smooth to line and level including necessary supports, scaffolding etc. as required and also including applying a coat of red oxide zinc chromate primer over the M.S. frame work and suspenders complete. 12.47.1 Including providing and fixing expanded metal of size 5.25 mm x 1.25 mm thickness welded to main runners and applying POP (calcium sulphate semi hydrate variety) to the expanded metal of thickness not less than 10 mm

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100mm sand cast Iron P or S trap,10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete including cutting and making good the wall sand floors wherever required : WhiteVitreous china Orissa pattern W.C.pan of size 580x440mm with integral type foot rests.

Providing and fixing wash basin with C.I. brackets,15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White VitreousChinaWash basin size 550x400mm with a pair of 15mm C.P. brass pillar taps.

Providing and fixing Stainless Steel A ISI 304(18/8) kitchen sink as per IS 13983 with C.I. bracket sand stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink with drain board 17.10.1.1 510x1040 mm bowl depth 250mm. 510x1040 mm bowl depth 250mm.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40 mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing : Rectangular shape 453x357mm

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15mm nominal bore.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore

Providing and fixing C.P. Brass extension nipple (size15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing 15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make, weighing not less than 1.970 kg.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C.waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-AL-PE) Composite Pressure Pipes conforming to IS-15450U.V. stabilised with carbon black having thermal stability for hot & cold water supply, capable to withstand temperatur

e) 4050 (50 mm OD) pipe

e upto 80°C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g.elbows, tees, reducers, couplers & connectors etc.with clamps at 1.00 metre spacing.This includes testing of joints complete as per direction of the Engineer in charge. Internalwork-Exposed on wall a) 1620 (20 mm OD) pipe

c) 2532 (32 mm OD) pipe

d) 3240 (40 mm OD) pipe

b) 2025 (25 mm OD) pipe

e) 4050 (50 mm OD) pipe

e upto 80°C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g.elbows, tees, reducers, couplers & connectors etc.with clamps at 1.00 metre spacing.This includes testing of joints complete as per direction of the Engineer in charge. Internalwork-Exposed on wall a) 1620 (20 mm OD) pipe

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-AL-PE) Composite Pressure Pipes conforming to IS-15450U.V. stabilised with carbon black having thermal stability for hot & cold water supply, capable to with stand temperature up to 80°C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required)e.g. elbows, tees, reducers, couplers & connectors etc.with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge.Concealed work including cutting chases and making good the wall etc. a) 1620 (20 mm OD) pipe

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-AL-PE) Composite Pressure Pipes conforming to IS-15450-2004U.V. stabilised with carbon black having thermal stability for hot & cold water supply, capable to with stand temperature up to 80°C including all specialfittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows,tees, reducers, couplers & connectors etc.with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work a) 1620 (20 mm OD) pipe.

b) 2025 (25 mm OD ) pipe.

c) 2532 (32 mm OD ) pipe.

d)3240 (40 mm OD ) pipe.

e) 4050 (50 mm OD ) pipe.

Taking connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc.complete (cost of water meter and stop cock to be paid separately).

Providing and fixing gun metal gate valve with C.I.wheel of approvedquality (screwed end): a) 25 mm nominal bore

b) 20 mm nominal bore

c) 32 mm nominal bore.

d) 40 mm nominal bore

e) 50 mm nominal bore

Providing and fixing gun metal non-return valve of approved quality (screwed end): 32 mm nominal bore Vertical

Providing and fixing unplastisised P.V.C. connection pipe with PTMT Nuts of approved quality and colour. 15 mm nominal bore with 30cm length.

Providing and fixing on wall face unplasticised-PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS:5382, leaving10mm gap for thermal expansion. b) Bend 87.5° 110 mm bend

Providing and fixing of material for the insulation of Water Storage Tank of with nitrile sheet , tapping with cello tape , Rockwood 6 inch per side, wire mesh, polythene , aluminum sheet 26 gauge cladding with dia of , complete job. 19 mm thick nitrile sheet

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including Hot finished welded type tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI :12701 marked with cover and suitable locking arrangement and making necessary holes for inlet,outlet and over flow pipes but without fitting sand the base support for tank

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A

Providing and fixing on wall face unplasticised-PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion. 110 mm

c) Shoe (Plain) 110 mm Shoe

Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar1:4(1cement:4 coarse sand) and making good the wall etc. complete. 110 mm

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15cm diametre and weighing not less than 440 grams.

Providing, laying and jointing glazed stone ware pipes class SP-1with stiff mixture of cement mortar in the proportion of 1:1 (1cement : 1 finesand) including testing of joints etc. complete : a) 100 mm diameter

b) 150 mm diameter

c) 200 mm diameter

Providing and laying cement concrete1:5:10 (1cement : 5coarsesand : 10 graded stone aggregate 40mm nominal size) all-round S.W.pipes including bed concrete as per standard design : a) 100 mm diameter S. W. pipe

b) 150 mm diameter S.W, pipe

c) 200 mm diameter S.W. pipe

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required.

b) 180x150 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

d) 250 mm diameter S.W. pipe

Providing and laying non-pressure NP 2 class (light duty) R.C.C.pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2(1cement: 2 fine sand) including testing of joints etc. complete : a) 150mm dia. R.C.C. pipe

b) 250 mm dia. R.C.C. pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Making connection of drain or sewer linewith existingmanhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix(1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) cement plastered on both sides with cement mortar 1:3 (1cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 100 to 250 mm diameter

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, sin

gle core cable in surface/ recessed medium class PVC conduit as required. a) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

b) 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Providing and fixing of material for the insulation of pipe with nitrile tube , tapping with cello tape for inner wall fittings . complete job including carriage. 19 mm thick, 50 mm dia (OD) ( PPR 25 mmm)

Providing and fixing of material for the insulation of pipe with nitrile tube , tapping with cello tape , Rockwood 6 inch per side, wire mesh, polythene , tapping with cello tape aluminum sheet 26 gauge cladding with dia . complete job including carriage b) 19 mm thick, 50 mm dia (OD) ( PPR 50 mmm)

c) 2 X 10 sq. mm + 1 X 6 sq. mm earth wire

c) 4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) a) 6 way (4 + 18), Double door

b) 8 way (4 + 24), Double door

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Providing and fixing circular/Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) a) 8 way , Double door

b) 12 way , Double door

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair

Supply of Surface Mounted Energy Efficient, LED Luminaires 12W LED Down Light (Round) Sutaible for 220v Single Phase Supply complete with driver circuit including making connections etc.as required.

Supply of Recessed Mounted Energy Efficient, LED Luminaires 18W LED Down Light Sutaible for 220v Single Phase Supply complete with driver circuit including making connections etc.as required.

Supply of of 36W / 38W LED Recessed Light Fixture Aesthetically designed 2x2 LED Flat panel with colour temp 4000K which provides soft- light and glare free symmetrical illumination. supplied with wedge bracket including making connection & accessories as required.

Supply, of Linear & Compact 10W Mirror Light with Decorative Grey Caps, Polycarbonate Body & Ribbed Opal Diffuser.

Supply of LED Luminaires BATTEN 20W LED Tube Light of Box Type Prewired Indoor Luminaire with Energy Efficient Electronic Ballast, with End Caps Complete as Required. (Technical Data System power 20W, CRI ≥80, Power Factor 20.95, System Luminous Efficacy ≥100)

Supply of LED luninaries BATTEN 40W LED Tube Light of Box Type Prewired Indoor Luminaire with Energy Efficient Electronic Ballast, with End Caps Complete as Required. (Technical Data System power 20W, CRI ≥80, Power Factor >= 0.95 System Luminous Efficacy >= 100

Supply of Bulk Head Luminaire, heat resistant Glass cover. suitable for 10W to 15W LED or Equivalent. (Technical Data System power 10W, CRI >= 80 , Power Factor >= 0.95 , System Luminous Efficacy underline >= 80

Supply of AC 230/250 volts, 50 112-300mm Exhaust Fans Including Providing Nuts, Bolts, Mounting Frame and Other Accessories etc. Complete as Required 300 mm sweep 900 rpm.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: 8, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise-75 degree C (max.). insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation of Exhaust fan in the existing opening, including making good the damage, Connection, Testing, Commissioning etc. as Required. Upto 450 mm sweep

SITC of CO2 Fire Extinguishers 4.5 kg capacity complete in all respect ISI: 15683 marked.

SITC of ABC FIRE EXTINGUISHER 4 KG capacity complete in all respect ISI: 15683 marked.

SITC of Fire Bucket stand made of M S angle suitable for and with 4 Nos Fire Buckets of 9.5 Ltrs capacity.

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.