REPAIR TO BOUNDARY WALL RETAINING WALL DRAINAGE COMPOUND WALL AND CERTAIN BR WKS ZONE A UNDER GE ARMY DHAR ROAD

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

Demolition of cement concrete (unreinforced) in ground floor, paving not exc. 15 cm thickness (below or above ground level) complete all as specified and directed

M&L 75mm thick PCC 1:3:6, type C-2 using 40mm graded crushed stone aggregates as in sub base of floor, finished even and fair, complete all as specified and directed.

M&L for 25mm thick sand filling under floors or in foundations including watering and consolidation as cushioning for laying of paver blocks complete all as specified and directed. Note :- Punned thickness of sand shall be measured and paid.

M&L for prepolised precast designer tiles of size 300x300x10mm outdoor/parking design in floors,(coloured, jointed and pointed in neat cement slurry with grey cement and pigments) to match the colour of fills complete all as specified and directed.

M & L for machine pressed precast concrete with grey cement and pigment interlocking paver block (coloured red/yellow) any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 grade complete all as specified and directed.

M & L for refixing machine pressed precast concrete with grey cement and pigment interlocking paver block (coloured red/yellow) any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 grade complete all as specified and directed.

M & L for machine pressed precast concrete with grey cement and pigment interlocking paver block (coloured red/yellow) any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade complete all as specified and directed.

M & L for refixing machine pressed precast concrete with grey cement and pigment interlocking paver block (coloured red/yellow) any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade complete all as specified and directed.

M&L for cement concrete type B-1, 1:2:4 (20 mm graded crushed stone aggregate) as in copings, window cills, kerb stone for foot path and similar items with plain fair finishing including chamfers, weathering, throating etc and set in CM 1:4 complete joints to match complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stoneswork and precast concrete articles complete all as specified and directed

M & L for cement concrete 1: 4 :8 type D 2 using 40 mm graded crushed stone aggregate as in foundation filling and mass concrete etc complete all as specified and directed.

M&L Providing Cement concrete 1 : 2 : 4 Type B1 (20mm graded crushed stone aggregate) as in roof kerbs or mud stops,in lintels upto 1.5 m span, copings slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

M & L for walling of random rubble stone masonary uncoursed well bonded , bedded and solidely hearted built in cement mortor 1:4 etc complete all as specified and directed.

M & L for walling of random rubble stone masonary uncoursed well bonded , bedded and solidely hearted built in cement mortor 1:4 except stone etc complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses. Hammer dressing witrh maximum depression on face from straight edge held against the dressed surface not exc 20 mm in lime or sand stone complete all as specified and directed

Racking out joints/pointing to random rubble or polygonal rubble uncoursed or brought up to courses built in cement or cement lime mortar complete all as specified and directed.

M & L for raised pointing to random or polygonal rubble, uncoursed or brought upto courses in cement mortar 1:4 complete all as specified and directed.

M & L for providing precast cement concrete type C1, 1 : 3 : 6 (20 mm graded crushed stone aggregate) as in bonders (for stone walling) etc., with plain fair faces including chamfered, weatherings throating etc., and setting in cement mortar 1:6 with joints to match complete all as specified and directed

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius butt in cm 1:6 complete all as specified and directed.

M & L brick work with sub class 'B' bricks, straight or curved on plan exc. 6 mtr mean radius built in cement mortar 1:6 but (except bricks) complete all as specified and directed.

M&L for half brick work with sub class 'B' brick straight or curved on plan exc 6m mean radius but in cm 1:4 complete all as specified and directed.

Taking down cement plaster or cement lime plaster on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar 1:4, to be finished even and smooth without using extra cement with water proofing compound by weight as per manufacturer's instructions complete all as specified and directed. (WPC will be paid separately).

Supply only integral water proofing compound, ISI marked, complete all as specified and directed.

M & L for preparation of new plasterd surface of walls and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489-2004, Alkali and fungal resistance, dirt resistance exterior paint of 100% required shade (Company Depot tinted) in with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.50 litre/10 sqm over new surfaces including 2mm thick water proof wall putty complete all as specified and directed

M & L for preparation of old plasterd surface of walls and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489-2004, Alkali and fungal resistance, dirt resistance exterior paint of 100% required shade (Company Depot tinted) in with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.50 litre/10 sqm over new surfaces complete all as specified and directed.

Demolition of cement concrete reinforced of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M & L for RCC M-25 type B1 1:2:4 (using 20 mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span including neccessary form work complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild steel TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Providing precast cement concrete 1:2:4, type B0, using 12.5mm graded crushed stone aggregate louvers & jallies, 25mm thick (measured solid), set in cement mortar 1:4, including all mouldings and shuttering complete all as specified and directed.

M&L for PCC 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in foundation for fencing post filling, and mass concrete, complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any decription not otherwise provided for complete all as specified and directed by Engr-in-Charge.

S & F posts and struts in fencing including cutting tops to shape as directed, drilling holes notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed

S & F Tie bars with screwed ends nuts, washers and mild steel plates for walls, chimneys, roofs arches, etc. king rods and straining bolts conforming to Fe-290 Gde-E-165 complete all as specified and directed

Dismantling of existing chain link fencing of any description complete all as specified and directed.

S & F in repair chain link MS galvanised fencing (wire dia 4mm , mesh size 100x100mm) complete all as specified and directed

S&F for galvanised two strand steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any standardral straining bolt including securing or tying at rossing with an provision of galvanised steel pin etc including restraining and resecuring making good complete all as specified and directed.

S&F in repair circular concertina coil punched tape (incl spikes and handle ) with 50 turns and loop dia 750mm, width of barbed wire 9mm dia and spacing clips 23.5mm to 24.5mm c/c and weight of coil not less than 10 to 14kg without packing coil length will be 6m when opened up etc fixing at any position/at any height, binding with angle iron ground pickets and binding with coil and binding wire as per manufactures,s instruction & sample as approved by GE/EIC complete all as specified and directed.

Brick work with sub class 'B' bricks straight or curved on plan exc 6 mtr mean in radius built in CM 1:4 in drain complete all as specified and directed.

M&L for PCC 1:4:8, Type D-2 using 40mm graded crushed stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B-0 using 12.5 mm graded crushed stone aggregate as in coping, including necessary form work and finished exposed surface of concrete complete all as specified and directed.

Extra for forming fair finished drain or channel over 30 cm inner girth in cement concrete , using extra cement, including forms , moulds, mitred/stopped ends etc. complete all as specified and directed.

M&L precast cement concrete type B1 1:2:4 (20mm graded crushed stone aggregate) set in CM 1:4 cover slabs, chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified and directed.

S & F mild steel framed work such as grills, grating, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description, over 10 cm width or girth, not other wise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for 75 mm thick cement concrete type C1, 1:3:6 (using 20 mm graded crushed stone aggregate) as in plinth protections, to be finished even and smooth without using extra cement complete including use of necessary form work complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning,or broken rubble mixed with earth around, in layers not exceeding 25 cm with PCC 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in fencing post filling,with posts and struts in fencing including cutting tops to shape as directed, drilling holes notching for wire with equal legs angle of 65x65x6(mm), 2.1 mtr height above ground level and 0.5 mtr ambedded in post hole & 1.0 mtr lenght in top T type with 4 nos hole for wire & 4 nos 6 mm dia ss wire covered with pvc coating 21.0 Rm and fixed both side wire rope clip including preparation of new painted steel surfaces of any description, over 10 cm width or girth, not other wise described and applying two coat of synthetic enamel paint over red oxide complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings etc complete all as specified and directed.

S & F rolled mild steel work in tubular trusses, purlins etc. including special shaped etc complete using ERW or induction butt welded tubes conforming to Gde ST-240 and painted one shop coat of zinc chromate primer paint (including preparation of surface) at contractor's workshop before fabrication complete all as specified and directed.

Refixing and fabrication only rolled mild steel work in tubular trusses, purlins etc. including special shaped etc complete using ERW or induction butt welded tubes conforming to Gde ST-240 and painted with one coat of zinc chromate primer paint (including preparation of surface) at contractor's workshop before fabrication complete all as specified and directed.

S & F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed (except sheets) complete all as specified and directed.

S & F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws (for Ridge) complete all as specified and directed.

Deduct Schedule of Credit of Rs. (-) 107540.00 (Minus) as listed in Schedule 'A' Part-II. Contract Sum shall be arrived after deducting the credit amount Note: Tenderers will not quote against this item being a firm amount.

Please Enable Macros to View BoQ information