SPECIAL REPAIRS TO BUILDING NO P-169 AT THE MLIRC UNDER GE BELGAUM.

Amount

Taking down Chowkhats or frames with shutters (without taking off shutters from the frame) of area exceeding 1.5 Sqm but not exceeding 4.0 Sqm each and taken as credit complete all as specified and as directed.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings etc, and taken as credit complete all as specified and as directed.

Demolition of cement concrete in ground floors n exc 15cm thick unreinforced (below or above ground level) and removal of debris not exceeding 100 meters complete all as specified and as directed .

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, precast concrete articles etc and removing rubbish off the premises and old unserviceable PCC Blocks/bricks and taken as credit complete. all as specified and as directed.

Dismantling boarding, any description, fixed in any position with nails and taken as credit complete. all as specified and as directed.

Dismantling wall or ceiling boards or insulation boards/ slabs any thickness including cover fillets etc, and taken as credit complete. all as specified and as directed.

Dismantling of mild steel work of any description and in any position etc and taken as credit complete. all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding , removing serviceable tiles to store and rubbish off the premises etc,complete all as specified and as directed.

Taking down cement plaster on brick or stone walls built in cement mortar etc including raking out joints ,hacking for key ,scrubbing down with water complete all as specified and directed..

Material and labour for Plain cement concrete type B1 1:2:4 (using 20 mm graded aggregate )25 mm thick as in sub base of floor etc including necessary steel form work complete all as specified and as directed..

Material and labour for Plain cement concrete type C2 1:3:6 (using 40 mm graded aggregate )75 mm thick in plinth protection and finishing the cement concrete surface even and smooth without using extra cement including necessary steel form work complete all as specified and as directed..

Material and labour for Pre-cast cement concrete solid block masonary type C1, 1:3:6 (using 20 mm graded stone aggregate) exc 10 cm width and setting in CM 1:6 complete all as specified and as directed

Supply and fix in repairs Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.45mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. Note :Make of Galvalume sheet : TATA Blue Scope Ltd/JSW (Colouron)/LLOYD

Supply and fix in repairs Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.45mm thick of any colour having tensile strength of 550 Mpa as in ridge , valley gutter fixed with self tapping screws complete all as specified and as directed. Note :Make of Galvalume sheet : TATA Blue Scope Ltd/JSW (Colouron)/LLOYD

Supply and fix Aluminium composit panel board 4mm thick as on for cladding/bush board with aluminium frame work of size 35mmx25mmx 2mm th aluminium section with necesary fitting and scaffolding extra, including dismantling old unserviceable panel board of any description and taken as credit complete all as specified and as directed.

Supply band fix PVC (SWR) eaves gutter half round/ square/ trapezoidal profile 150mm bore including pipe accessories PVC holder bats , bolts nuts et and including dismantling of exsiting rain gutter of any description and taken as credit complete all as specified and as directed.Note : Make of PVC eaves gutter :Finolex/Supreme/Prince

Material and labour for High pressure steam cured (HPSC) non asbestos fibre cement building board 4mm thick in false ceiling fixed with aluminum anodized snap grid of 60x60cm in ceiling with Tee section 35x25x1.25mm, L angle section25x25x1.25mm thick including 2mm dia GI hanging wire including all hanger fittings etc and applying three coats of white wash on ceiling board complete all as specified and as directed . Note : (i) Make of HPSC Board : EVEREST /ARMSTRONG (ii) Thickness of aluminium anodisation shall be of 15 microns . (iii) Make of aluminium anodised section : Jindal/Indal/Hindalco .

Supply and fix Mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe 410 -W (Gde E- 250) quality A complete all as specified and asdirected.

Material and labour for Premium quality Non-skid joint free coloured ceramic tiles 7 to 8mm thick (square/rectangular) , light shade ,area of each tile exceeding 0.18 Sqmbut not exceeding 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over including cement screed bed or bedding layer of mortar in CM 1:6 , 15mm thick complete all as specified and as directed. Note :Make of ceramic tile : HR Johnson/Kajaria/Somany

Material and labour for Rubber moulded reflective chequered cement concrete tiles 30cm x 30cm x 25mm thick,set, jointed and pointed in neat cement slurry in floors, with mixture of grey and white cement in equal proportions, and 15mm thick screed bed or bedding layers of (1:4) cement mortar for floor finishes complete all as specified and as directed.

Supply and fix Powder coated aluminium frame (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and as directed..Note : Make of aluminium frame : Jindal/Indal/Hindalco

Material and labour for Aluminium anodised doors standard section of size 64x38x1.4mm for frame and section size 47x25x2mm for vertical style section size 46.72x44.45x1.4mm for top and central rail section size95x44.45x2mm for bottom rail,section size 19x17.3x0.80mm for glazing clip for shutter including fabrication to required size and fixed with 5mm thick sheet frosted glass in top pannel and 4mm thick aluminium composit panel board including fitting etc with door closer,handle,mortise lock heavy duty and door spring heavy duty etc complete all as specified and as directed. Note:(i) Thickness of aluminium anodisation shall be of 15 microns . (iii) Make of aluminium anodised section : Jindal/Indal/Hindalco . (iv ) Make of aluminium composit panel board :Alstrong / Aludecor/Alucobond (v) Make of Glass : Saint gobain/modi Guard/Gold fish

Supply and fix Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, etc complete all as specified and as directed . Note :Make of Collapsible gate :Shree Lakshmi Engg Wks, Bangalore/M/S Senthil Rolling Shutters & Engg Co, Chennai/M/S Jayaraj Industries, Chennai

Supply and fix 110mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wallscomplete all as specified and as directed Note : Make of UPVC Pipe : Finolex/Supreme /Prince

Supply and fix 4 mm thick frosted sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane and extra over sheet glass, ordinary quality, if sheet glass is ground or obscured or frosted, on one side including hacking out old broken glass (any thickness/size, quality or description) from glazed with putty or fixed with beads etc,complete all as specified and as directed Note : Make of Glass : Saint Gobain/Modi Guard/Gold Fish

Material and labour for Rendering 10mm thick in CM 1:6 on brick surfaces and finished even and smooth without using extra cement etc, complete all as specified and as directed. .

Material and labour for Rendering 5 mm thick in CM 1:4 over 10mm thick plaster in CM 1:6 on brick or concrete surfaces using water proofing compound etc,,complete all as specified and as directed .

Supply only water proofing compound . Make ;impermo/Roff/Cico

Material and labour for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces etc, complete all as specified and as directed.

Material and labour for Complete removal of existing treatment on old walls and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces etc, complete all as specified and as directed .

Material and labour for Preparation of newly plastered surface of walls and applying two coats of oil bound distemper over a preparatory coat of chalk whiting etc, complete all as specified and as directed.

Material and labour for Complete removal of existing treatment on walls and applying two coats of oil bound distemper over a preparatory coat of 1mm thick wall care putty on wall including necessary preparation of surfaces etc, complete all as specified and directed.

Material and labour for Preparation of old steel surfaces , exc 10cm in width or girth etc,and applying one coat of synthetic enamel paint complete all as specified and as directed..

Material and labour for Preparation of new steel surfaces of any description exc 10cm in width or girth etc,and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed..

Taking down carefully Sub main wiring of any type and size from the existing surfaces , including dismantling of old unserviceable submain wiring of aluminium conductor cable of any size and taken as credit complete all as specified and as directed.

Material and labour for Point wiring with FRLS PVC insulated unsheathed electric cable confirming to IS:694,1100 V grade AC,single core having multistranded copper conductor of size 1.5 sqmm nominal cross sectional area for phase and neutral in and including non metallic rigid PVC conduit ISI marked medium grade not less than 20 mm dia with all conduit accessories in concealed wiring system and provision of FRLS PVC insulated unsheathed electric cable confirming to IS:694,1100 V grade AC,single core having multistranded copper conductor of size 1.5 sqmm green colour , connected to common earth dolly and taking down unserviceable point wiring from existing surface including provision of suitable size of modular metal box fixing in wall with white colour cover plates and all accessories for mounting modular type switches, sockets, fan regulators, bell pushes etc. for one light point controled by one 1 way switch complete all as specified and as directed. NOTE: (i) Make of PVC cable :Finolex/Polycab/RR Kabel (ii) Make of PVC conduit : Avon Plast/Presto plast /Garware .

All as described in item No. 36 here in before but for One fanpoint controlled by one switch and regulator

All as described in item No. 36 here in before but for one 03 pin socket outlet on independent socket 05 amps point .

All as described in item No. 36 here in before but for one 05 Amps socket outlet on the same board with other switches.

All as described in item No. 36 but wiring with 2.5 SqmmFRLS PVC insulated unsheathed cable copper conductor multi stranded (for 15 Amps power socket) with one run of copper conductor FRLS PVC insulated multi-stranded cable 2.5 Sqmm for earth continuity conductor and connecting to common earth dolly, complete all as specified and as directed.

Supply and fix in repairs Modular switch piano type 6 Amps flush button 230 volts AC one way, complete all as specified and as directed. Make -Anchor (Roma)/Legrand/CONA

Supply and fix in repairs Modular switch piano type 16 Amps flush button 230 volts AC one way, complete all as specified and as directed. Make -Anchor (Roma)/Legrand/CONA

Supply and fix in repairs Modular socket outlet 6 Amps 2/3 pin combined flush type multipurpose 2 module,complete all as specified and as directed. Make -Anchor (Roma)/Legrand/CONA

Supply and fix in repairs Modular socket outlet 6/16 Amps 2/3 pin combined flush type multipurpose 2 module,complete all as specified and as directed. Make -Anchor (Roma)/Legrand/CONA

Supply and fix in repairs or replacement of PVC or Polycarbonate ceiling rose 3 terminal , isolated body suitable for 230 volts AC supply, complete all as specified and as directed. Make -Anchor (Roma)/Legrand/CONA

Material and labour for Submain wiring complete with 1100volt grade FRLS PVC insulated unsheathed multistranded cable of size 02 run of 2.5 sqmm copper conductor cable confirming to IS 694 drawn through and including non metallic rigid PVC CONDUIT in Ivory/Grey/white colour medium grade etc fixed in wall/ceiling including provision of 01 run of 1100volt grade FRLS PVC insulated unsheathed multistranded cable of size2.5 sqmm copper conductor cable and Connected to earth dolly complete all as specified and as directed. . Notes: (i) Two different color wires shall be used for phase and neutral . (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/ copper thimbles . (iii)02 run of 2.5 sqmm and 01 run of 2.5 sqmm including 01 run of PVC CONDUIT will be measured as one length (iv)Make of PVC copper conductor cable:- Finlex/Poly cab/ Asian. (v) Make of PVC conduit :Avon plast/Presto plast /Garware

Material and labour for Submain wiring complete with 1100volt grade FRLS PVC insulated unsheathed multistranded cable of size 02 run of 4.0 sqmm copper conductor cable confirming to IS 694 drawn through and including non metallic rigid PVC CONDUIT in Ivory/Grey/white colour medium grade etc fixed in wall/ceiling including provision of 01 run of 1100volt grade FRLS PVC insulated unsheathed multistranded cable of size 4.0 sqmm copper conductor cable and Connected to earth dolly complete all as specified and as directed. . Notes: (i) Two different color wires shall be used for phase and neutral . (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/ copper thimbles . (iii)02 run of 4.0 sqmm and 01 run of 4.0 sqmm including 01 run of PVC CONDUIT will be measured as one length (iv)Make of PVC copper conductor cable:- Finlex/Poly cab/ Asian. (v) Make of PVC conduit :Avon plast/Presto plast /Garware

Material and labour for Submain wiring complete with 1100volt grade FRLS PVC insulated unsheathed multistranded cable of size 02 run of 6.0 sqmm copper conductor cable confirming to IS 694 drawn through and including non metallic rigid PVC CONDUIT in Ivory/Grey/white colour medium grade etc fixed in wall/ceiling including provision of 01 run of 1100volt grade FRLS PVC insulated unsheathed multistranded cable of size 6.0 sqmm copper conductor cable and Connected to earth dolly complete all as specified and as directed Notes: (i) Two different color wires shall be used for phase and neutral . (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/ copper thimbles . (iii)02 run of 6.0 sqmm and 01 run of 6.0 sqmm including 01 run of PVC CONDUIT will be measured as one length . (iv)Make of PVC copper conductor cable:- Finlex/Poly cab/ Asian. (v) Make of PVC conduit :Avon plast/Presto plast /Garware

Supply and fix in repairs LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed . Note : Philips cat part no : RC370B LED30S-6500 or Equivalent price and specification in M/S Wipro/CG

Supply and fix LED lamp with suitable type holder 40 W bulb for fixing at target with suitable arrangement alongwith all accessories connecting up with twin core twisted PVC copper conductor cable lamp from point to lamp complete all as specified and as directed . Note :C&S electric LED Hammer Bulb 40 W or equivalent M/S Wipro/CG/Philips

Supply and fix LED spot light 9 Watt for fixing at target with suitable arrangement alongwith all accessories connecting up with twin core twisted PVC copper conductor cable lamp from point to lamp complete all as specified and directed . Note Make:-AruSPARC LIGHTS LED WALL SPOT LIGHT with metallic body (9 watt ,white) or equivalent M/S Wipro/CG/Philips

Supply and fix in repair Round shaped 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper PVC conductor cable of suitable size complete all as specified and directed . Philips cat part no Sleek Surface SM251CW: or Equivalent price and specification in M/S Wipro/CG

Supply and fix in repair LED INTEGRATED BATTEN T5 tube light fitting type 1x 18/20 watt indoor decorative aluminium extruded T5 LED Battens-integrated type complete with all accesories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed . Note : .Make: Philips cat part no :BN 021C LED20S PSU CDL or Equivalent price and specification in M/S Wipro/CG

Supply and fix in repair LED INTEGRATED BATTEN T5 tube light fitting type 1x 9 /10 watt indoor decorative aluminium extruded T5 LED Battens-integrated type complete with all accesories internally pre-wired and including connecting up with twin core twisted flexible PVC copper conductor cable with suitable size complete all as specified and directed .Note :Make: Philips/M/S Wipro/CG

Supply and fix in repair LED street light fitting 25 Watt 230 V AC outdoor type with high pressure die cast aluminum hou sing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protectioncomplete all as specified and as directed . Note : Make :Philips BRP020 LED HP/CW 240V 25Wequivalent price and specification of M/S Wipro/CG

Supply and fix Wall mounting fan, 300 mm sweep, 230 Volts, heavy duty , single phase, with all fixing accessories including provision of suitable clamps for fixing to wall and making good disturbed surfaces matching with the existing surfaces removing unserviceable wall mounting fan deposited to MES store complete all as specified as directed. Make: Bajaj/ CG/Orient.

Taking down old unserviceable MCCB DBs/MCB DB including MCB/MCCB/Isolaters and taken as credit complete all as specified and as directed.

Supply and fix Factory made epoxy powder coated distribution board double door TPN 4 ways (VTPN MCCB DB) with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, neutral bar, strandard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with Knockouts and suitable for one FP MCCB 100 Amps as incomer and SP/TP MCBs (or any combination of SP/TP MCBs ) outgoings complete all as specified and as directed. . Make: Siemen /Legrand/Indo Asian

Supply and fix in replacement MCCB 4 pole 100 A 16KA 50HZ AC supply current rating conforming to IEC-609472 & IS-139473 including dismantling old one and taken as credit complete all as specified and as directed.. . Make: Siemen /Legrand/Indo Asian

Supply and fix Factory made epoxy powder coated distribution board SPN 12 ways double door with acrylic top cover (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, neutral bar, strandard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plate with knockouts and suitable for one SPN MCB 32/40 Amps as incomer and 10 SP MCBs as outgoings complete all as specified and as directed.Make: Siemen /Legrand/Indo Asian

Supply and fix MCB SPN 40 to 63 Amps 10KA C curve 50HZ ,240 Volts AC supply including dismantling old one and taken as credit complete all as specified and as directed.. .Make: Siemen /Legrand/Indo Asian

Supply and fix MCB SP 6 to 32 Amps 10KA C curve 50HZ ,240 Volts AC supply including dismantling old one and taken as credit complete all as specified and as directed.. .Make: Siemen /Legrand/Indo Asian

Material and labour for Electrical earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick, burried directly in ground vertically, (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level, connected to GI wire 4mm dia (7.5 metre long) by means of bolts, nuts, washers made of galvanized iron connected to earthing to body of equipment. GI wire protected by 15mm dia light grade GI pipe (7.5 metre long) and watering arrangements with 20 mm dia GI pipe medium grade and GI funnel all as specified and shown in Electrical Plate No 3 of MES Schedule (SSR) Part I including necessary excavation and earth work in any type of soil, charcoal dust salt, and PCC 1:2:4 type B1 in chamber, RCC 1:2:4 type, B1 cover slab, 40mm thick with 6mm dia mild steel bars at 100mm centre to centre both ways and with 6mm dia MS hook complete, and testing of Earth resistance complete all as specified and as directed.

Supply , lay and test cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 35 sqmm 3.5 core including lugs,thimbles and ferrules etc laid in trenches ,fixed to wall ,floor etc complete all as specified and as directed.Make : Gloster/Poly cab/CCI

Excavation in trenches n exc 1.5m wide and n.exc 1.5m depth for laying of cables/ GI tubes etc, in any type of Soil .complete all as specified and as directed.

Returning, filling in including spreading levelling and well ramming in layers n exc 25cm thick with soil obtained from excavation .complete all as specified and as directed.

Removing excavated material/surplus soil n exc 50m & depositing where directed at a level n exc 1.5m above the starting point .complete all as specified and as directed.

Material and labour for Double wall corrugated High Density Polymer Ethyl pipes(SDR 17) of ISI marked 63 mm outer dia and 50 mm inner dia including necessary fittings like couplers,bends,end caps etc as in cable protection fixed to poles with necessary suitable MS clamps, bolts, nuts, washers or laid in trenches/ roads crossings etc.complete all as specified and as directed. Make : Ketron/Rex/Duraline

Supply and lay 40 mm bore Galvanized iron pipe , “Light grade”, including all fittings and fixed on pole/walls/in road etc for cable protection complete all as specified and as directed. Make : TATA/JINDAL/Prakash surya

Supply and Install 1.50 Ton Hi wall split units ,inverter type for working on 230 Volts , SP , 50 Hz supply , Indoor, outdoor (Copper Condenser coil, Copper cooling coil and evaparator including required length of copper tubing and copper cables for connecting indoor and outdoor units) complete cardless remote control unit and with in-built ioniser and plasma filter for better indoor air quality with BEE 3 Star rating and year of manufacturing 2022 with Refrigerant - 410 gas filling complete. Make: Hitachi/Carrier/Blue Star

Note : The rate quoted by the tenderer shall be inclusive of the following provisions :- (i) UPVC drain pipe not less than 20 mm dia from indoor unit (any floor) to upto ground level/ near to drain to be fixed with proper size base plate with clamps complete. (ii) Copper pipe 20mm dia and 15 mm dia with 20SWG thickness refrigerant Piping with 19 mm thick Closed Cell rubber nitrile, Class "O"- arm-flex insulation and including connection complete of required length (iii) GI Powder coated brackets 16 SWG for fixing of split ACs and including grouting with suitable size fastners

Supply and Install Voltage stabilizer automatic for low and high voltage with electronic transistorised relay/ time relay for two min SP, 50 Hz with volt meter display and operating voltage between 130 to 300 Volt cap 4.0 KVA(not less than 17 Amp) complete all as specified and as directed. Make : V Guard/Premier /Syscom

M/s. KIRAN M CHOUGULE

M/s B C CHOUGULE

ASHOK M RAJGOLKAR

SHRI.H.R.PATIL

SAMARTH ASSOCIATES

M/S MAHADEV M PATIL

Manak landmarks