Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹26.5 LAccepted-Finance WEST BIDYUTPUR MALDA | MALDA | MALDA | WEST BENGAL | L1 | Accepted-Finance Offered lowest rate. | |
| 2 | L2₹26.5 L+₹1,742.41 (0.07%)Rejected-Finance PAKUAHAA MALDA | MALDA | MALDA | WEST BENGAL | L2 | Rejected-Finance Higher than L1 | |
| 3 | L3₹26.5 L+₹3,155.89 (0.12%)Rejected-Finance MAHESMATI MALDA | L3 | Rejected-Finance Higher than L1 |
Tender Value
Refer Docs
EMD Value
₹62,700
Closing Date
2 Sept 2024, 4:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
EXECUTIVE ENGINEER, MALDA MECHANICAL DIVISION,PHED
Office of the Executive Engineer, Malda Mechanical Division, PHE Dte. Doulatpur PHE complex, P.O. Maliha, Dist. Malda, PIN 732102
Supply, installation, commissioning and trial operation of electro-mechanical components at T/W no. I, II and making compound yard lighting arrangement at T/W no. I of Sonapur Water Supply Scheme in the District of Uttar Dinajpur under Malda Mechani
2024_PHED_728677_7
WBPHED/EE/MLMD/NIeT_08 of 2024-25
Open Tender
Electrical Work/ Equipment
Item Rate
90 days
Doulatpur PHE complex, P.O. Maliha, Dist. Malda
Please refer Tender documents.
4 documents required · 4 mandatory
₹62,700
Yes
10 Sept 2024
9 Aug 2024
4 Sept 2024
9 Aug 2024
2 Sept 2024
9 Aug 2024
Amount
Supply and delivery at site of following pumping machinery and electrical accrssories:
Clear water vertical wet type submersible pump suitable for bore well conforming to IS : 8034 (and as amended thereafter) with standard MOC for portable clear cold water and BEE 3 Star (min) Rated capable of discharging noted M³/hr against head of water column. The pump shall be directly coupled with a continuous rated 2-pole suitable wet type vertical squirel cage induction motor conforming to IS : 9283 (and as amended thereafter), suitable for operation in AC Three phases 415 V, 50HZ (category B motor). *TC & GC should be submitted for pump-motor set.
For T/W No.- I Discharge of clear water (Q) = 28 m³/hr, Total Head (H) = 60 Mtrs. Shaft- Stainless Steel, Impeller- S.S/GM, Outlet Size- 80mm. Motor must be suitable for operation with star-delta starter
For T/W No.- II Discharge of clear water (Q) = 28 m³/hr, Total Head (H) = 60 Mtrs. Shaft- Stainless Steel, Impeller- S.S/GM, Outlet Size- 80mm. Motor must be suitable for operation with star-delta starter
2.5 sq.mm x 3 core water proof flat submersible cable (PVC insulated Cables with flexible bright annealed Copper conductor for voltage grade upto 1100 Volts conforming to IS : 694 as amended upto date). for above pump-motor set as per site requirement (For T/W No. I, & II).
1.1KV grade 25 sq.mm 3.5 core XPLE Aluminium armoured cable conforming to IS 7098 (Part-I) 1988, with upto date amendments as per site requirement. (For T/W No. I, II & III)
100 Amps Re-wireable porcelain fuse unit type TPN Main Switch with steel sheet enclosure (Conforms: IS/IEC600947-1&3).
Supply and delivery of 100 Amps Kit-kat rewireable proceliain fuses carrier & base (Specification-IS:2086).
Supply, delivery and storage at site of wall mounted 2mm. thick epoxy painted sheet steel enclosed front open fully panel for fully automatic cum manual control centre for operation of the pump motor in STAR-DELTA mode, actuator with DOL starter, Chlorinator with DOL starter and timer operated outdoor and indoor lighting and also spares feeder as per approved drawing and NIT specification. Range of PMCC Panel : 7.5 HP to 12.5 HP *TC & GC should be submitted for PMCC Panel. (All spare & components as per approved vendor list of PHED).
Supply and delivery of the following valves, pipes and gauges etc at site-- (Make: Approved Vendor list of PHED.) (For T/W No. I & II)
80 mm dia M.S. seamless column pipe (black) 6.8 mm to 7.1 mm thick with 150 mm long heavy type socket at one end.
3.0 mtrs Long.
1.5 mtrs Long.
80mm dia. Cast Iron Wafer type Butterfly Valve generally as per BS-5155, having body of Cast Iron as per Is:210 gr. FG-260, disc of SS Gr CF-8, Shaft of St. steel AISI-410, "O" ring for shaft seal of Nitrile rubber, valve are suitable for PN 1.0 rating. Valves are operated by suitable (Three phase 415V), multiturn electrical actuator without starter). *TC & GC should be submitted for valve and Actuator.
80mm dia CIDF Non-Raising Sluice Valves, PN 1.0 rating (Conforming to IS:14846) having body door/dome/Bonnet and cover of cast iron Gr. FG 260, spindle of IS 6603, Gr-12 cr-13, spindle nut & seat rings are of Gunmetal as per IS:318 LTB 2.- 1 no., CIDF single door swing Non Return Valve, PN 1.0 rating (Conforming to IS:5312 Part I), having body, door, cover in graded cast iron to IS:210 Gr. FG200, body & door rings & bearing block of leaded tin bronze to IS:318 Gr. LTB2- 1 no., CIDF 90° Bend-1no., CI Flanged Tee-1no. Blank Flange-1no., CI/ MS flanged Short Piece 0.50 mtr.- 2 nos, CI/ MS flanged pipe 1 mtr.- 1 no. etc as per IS specification and certification for construction of delivery pipe line and wash out line.
Heavy type 250mm/Suitable dia split type tube well cover with 12 mm thick clamping arrangement including holes for column pipe, air pipe and cable entry with 2 sets heavy type suspension clamp, nuts, bolts and washer as per departmental design.
Anti snapping safety device for pump set by supplying suitable size of MS angle busket and nylon rope of required length including supplying of nuts, bolts and all other materials.
150mm dial Pressure gauge [Range 0-7kg/cm²] with glycerine filling inside the dial including brass cock and fitting complete [This cost includes 15mm. dia G.I. pipes and specials].
100mm dial Depth gauge capable to measure direct reading in feet with steel air pipe with all accessories and including supply of good quality hand pump. [This cost includes 15mm. dia G.I. pipes and specials].
Supply,delivery of M.S Kiosk box of 661mm x 559 mm (LxW) Size having thickness of 1.5 mm with angle support at four legs having hight of 661 mm with provision of locking arrangement, supply of lock,cable entry point incl. painting by one coat of black paint over one coat of primer all complete.
50mm. dia. non metalic pipes (IS:14930) and specials for protection of submersible cable (as per site requirement).
Making brick pillar 0.25 x 0.25 x 0.75 Mtr/Suitable hight for supporting of valves and pipes with 12mm thick plaster and net cement finish complete.
Making suitable size pump foundation including erection of Kiosk box with supplying of necessary cement, sand and stone chips including plastering and net cement finish complete.
Laying of 25 sq. mm. 3.5 core AL. Ar. Cable of sl no 5.00 in wall/ floor by supplying of all necessary materials as per IE Rules and as per direction
Making double earthing arrangement in compliance with IE rules by G.I. pipe electrode of 50 mm. dia 3 mtr. Long 2 Nos for panel and pumping machinery 25 mm. x 6 mm. G.I. earth strips from earth pit to panel and all other accessories required to complete the work.
Installation of the materials (to be supplied under above sl no. 2.00 to 9.10) such as Pump motor set with column pipes, valves, panel fitting-fixing pressure gauge, depth gauge, Non-return valve & drawing delivery out-let & washout line with the supplied specials/accessories , antisnapping cage of suitable size including supply of cable gland, sockets, wooden board, control cable etc including brick, sand, cement rod etc as required to complete the job as per direction and upto the entire satis faction of the EIC.
Supply and delivery at site 3 phase oil cooled type Servo Motor operated copper wound line voltage corrector of 15 KVA for TW-I & II conforming to IS-9815 (Pt.-1)-1994 suitable for un-balanced input voltage Phase to Phase 200V.-500V including first filling oil as per IS-335 where applicable as per approved drawing and NIT specification.
Supply and delivery of following materials at site for T/W-I& II.
100 Amps Re-wireable porcelain fuse unit type TPN Main Switch with steel sheet enclosure (Conforms: IS/IEC600947-1&3).
Re-wireable type TPN Changeover switch 100 Amps 415V, 50Hz, 4p offload with steel sheet enclosure (Conforms: IS/IEC60947-1&3).
100 Amps, 4way, wall mounted Copper Busbar Chamber with steel sheet enclosure (Conforms:IS/IEC:60947-3).
1.1KV grade 25 sq.mm 3.5 core XPLE Aluminium armoured cable conforming to IS 7098 (Part-I) 1988, with upto date amendments. (For T/W No. I& II)
Making brick built foundation with supplying of all required materials suitable for the above voltage stabilizer by (4:1) cement mortar including holding down foundation bolts and plaster with neat cement finish, sloping all complete as per direction of EIC.
Fitting , fixing of change over switch, Busbar chamber and main switch as mentioned in item no. 13.02 to 13.04 on the iron angle frame of suitable size fixed at suitable position on wall by supplying all necessary fixing materials all complete as per direction of EIC.
Installation of the above voltage stabilizer as in item no. 13.00 on the foundation including making all connection complete as per direction of EIC.
Drawing & connection of cable on wall as in item no. 13.05 & all connection complete with all equipment as per requirement & as per direction of EIC.
Making joints of the cable by Supplying compression type gland thimple socket etc as per requirement & as per direction of E.I.C.
Double earthing the whole installations complying with IR Rules including supplying of all necessary earthing materilas for voltage corrector device to complete the job as per direction of EIC.
Supply & delivery of automatically controlled Diaphargm type Chlorinator for accurate dosing of Chlorine solution into the water by connecting metering pump ( Diaphargm type) having following specification:- Pump type :: Diaphargm Liquid :: Chlorine solution Capacity ( LPH) :: 0-100 Pressure kg/cm2 ( Testing) :: 10 Pressure kg/cm2 ( suction) :: Flooded Pressure kg/cm2 ( Hydro) :: 15 Connection Suction :: ½” Hose Holder Connection Discharge :: ½: Hose Holder MOC Liquid End :: PP Diaphragm :: PTFE NRV :: PP Drive capacity :: 0.5HP, 3 phase, 50Hz, 415V, 1440 RPM Motor Coupling capacity :: Flexible Spider Strainer :: Y type, PP, ½” BSP (F) Pressure Relief Valve :: Inbuilt. Solution Tank :: 100 ltr capacity ( Including making provision for inlet line to the actual storage tank of dosing solution of all materials. Test & Warranty Certificates are to be submitted at the time of delivery
Installation of above supplied Chlorinator with all accessories, PVC tank and drawing of power line as per IE Rules by supplying PVC copper wire & continuous earthing. This includes the cost of all necessary CC foundation ( at least 200mm height) with concrete mixture ( sand, cement, stone) and neat cement finish by supplying of all required materials and testing the entire set as per entire satisfaction of the EIC. (Power will be fed from PLC panel of Pumping machinery)
Making internal electrification of pump house consisting of two bracket point, one tube light point, two bulk head point, one fan point and 1 NO. 74 watt LED fixture with arm bracket at outside and one three pin plug point including supply of all necessary materials to complete the work as per IE rules and as per direction (All the fittings and lamp should be LED type as per choice of EIC).
Making Compound Lighting arrangement and allied works at Head work site of T/W-I.
Supply & delivery at site of 9mtrs long steel tabular pole with sole plate as per direction of EIC (Designation- 410 SP-26.(Over all length-9.00mtr, planting depth- 1.5mtr, Length of section)(Bottom-5.0mtr, middle- 2.0mtr, Top- 2.0mtr,) Outside Dia & Thickness of Section(Bottom-114.3x4.50mm, Middle-88.9x4.05mm, Top- 76.1x3.25) Approx Weight of Pole-92Kg)including supply and fixing of single arm header of 40mm dia 1.5 m long CI base plate and cap etc.
Erection of 9 Mtr Single Steel tubular pole of length as given below with sole plate & Cap etc. in CC foundation (Proportion and dimension indicated below), having 600x600x750 mm thick CC (4:2:1) base block below sole plate/pole with hard jhama metal including CC (6:3:1) base block (around the pole) dimension 0.60x0.60x0.50 mt. above ground level including 2 mm thick neat cemented finish and GI earth bolt and earthing arrangement by 8SWG GI Wire,after making drilled holes etc. on pole including filling up the excavated earth pit with shifted soil and ramming properly.
Supply & Laying of 1.1 KV Gr. 2 core 6 sq.mm XLPE Armored Alu. Cable (Approved make) on wall/surface incl. S & F MS saddles with earthing attachment in 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting as directed by EIC.
Supply & Laying of 1.1 KV Gr. 2 core 6 sq.mm XLPE Armored Alu. Cable in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed.
Supplying and fixing 2+4 way SPMCB with 40A DP Isolator-1no & 6-32 Amp-3-nos 240/415 V MCB of Breaking capacity 10kA & B characteristics with MCB enclosure and necessary connection as per direction of EIC.(Approved make)
Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry 1.1 KV Gr. 2 core 6 sq.mm XLPE Armored Alu. Cable incl. Finishing the end of the same by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials as per direction of EIC.
Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire of 3 x 22/0.3 (1.5 sqmm)(Approved make) through GI pipe and making necy. connection as required as per direction of the E.I.C (From pole loop box to LED fittings).
Supplying and Fixing 250 x 250 x 100mm GI water proof looping cable box having hinged GI Top Cover having 4 mm thick with rubber gasket lining, railway type mechanical locking arrangement with required GI Pipe for cable laying from ground to loop box, earthing terminal with lug etc. of the following sizes as indicated below, Comprising of one 250 V, 6A SPMCB unit, one NL on porcelain insulator etc. and housing the same in pole muffing incl. addition and alteration to the existing CC muffing (6:3:1) after dismantling the damaged looping cable box etc. where necy. incl. painting as directed by EIC.
Supply and fixing of street light luminarie IP 66 LM6-HPDC Housing Street light aerodynamically designed with better thermal management/ Potted driver is to be provided,the luminaire and housing should be from the same manufacturer(cat no-BRP 062 LED 84 CW SLC S1 PSU) Make-Philips OR Equivalent and same techinal specification . Each Fixure is to be earthed with the erected steel tabular pole.
S/Fixing of die cast aluminium housing of gate light 1x40watt LED Outdoor luminiare (make-Havells- RUBYPT35WLED757PSYMTOPC / CORALPT35WLED757PSYMTOPC)Milky white Decorative Post top for 360° indirect light. IP 65 protection Resistant to impactb with suitable net protection and corrosion as per direction of EIC.
Supply ,delivery, fitting fixing of nomenclature made from improted acrylic sheet letter of different sizes with different colours asper choice of EIC.The subect matter as directed by EIC shall be fixed on iron structure of size (10' x 6') and should be fitted on MS Angle (Size - 65 mm X 65 mm X 6 mm ) and ISMC 100 with epoxy coated including all necessary civil work after grountig the MS frame on the roof of the buildung and making necessary pillers, plasters, neat cement finissing etc to complete the work as per direction of EIC including supplying all required electrical materials. Colour type and colour letter & graphics will be as per direction of EIC.
Painting all the single arm G.I brackets, poles, pipes etc. with 2 coats of Synthetic Enamel paint over 1 coat of Red Oxide primer after cleaning and preparation of surface by emery paper all complete as per direction.
Supply & delivery of plastic Chair without arm.
Supply & delivery of plastic Table.
Supply, delivery & installation of the following Fan as directed by EIC. Ceiling Fan 1200mm sweep including Fan clamp as and when required.
Commissioning of the installation with full satisfaction of EIC.
Trial operation. Maintenance, guarding of the installation roud the clock for a period of 90 (ninety) days from the date of receipt of service connection by engaging personnel having sufficient experience in electrical installation.
N.B. - Make as per departmental approved vendor list.
ADD GST @ 18%
ADD Cess @ 1%
PABITRA MANDAL
ANIMA ENTERPRISE
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .