SPECIAL REPAIR TO BLDG NO T-56 T-73 AND T-78 AT AFTC UNDER GE (WEST) DELHI CANTT-10

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified & directed.

Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets as in roof coverings including ridge complete all as specified & directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified & directed.

Dismantling framed timber scantlings any size in section, in any position (as in purlins etc) complete all as specified & directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls incl racking out joints, hacking for key, scrubbing down with water, etc. complete all as specified & directed.

Dismantling floor hearth or wall tiling incl cement mortar bedding, terrazo dado, (incl backing) removing services and tiles to store and rubbish off the premises complete all as specified.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar, complete all as specified and as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, incl cover fillets and frame work complete all as specified & directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4 sqm each complete all as specified & directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) not exceeding 1.5 sqm each complete all as specified & directed.

M&L for brick work with sub class 'B' old size bricks in cement 1:6, straight or curved on plan exceeding 6m mean radius complete all as specified & directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 (40mm graded crushed stone aggregate) for plinth protection laid in bays and finished even and fair incl filling the joint with bitumen mastic all as specified and directed over rammed earth complete all as specified & directed.

M&L for 25mm thick PCC 1:2:4 type B0 using 12.50 mm graded crushed stone aggregate as in leveling course of sub base all as specified and directed.

S&F joint free coloured Non-skid rectified ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in cement mortar 1:6 complete all as specified & directed.

M&L for light shade Vitrified Ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

M&L for Glazed ceramic tiles in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, over 10mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces complete all as specified & directed.

M&L for machine cut kota stone slab flooring 18 to 20 mm thick over screed bed or bedding layer 15mm thick of cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & directed.

All as per item No.17.00 here-in-before but on vertical surface as in dado/ skirting in any height incl all cutting and wastage incl 10mm thick rendering in cement mortar 1:4 complete all as specified & directed.

M&L for Bees wax polishing the old Kota stone floor by grinding, scrubbing by machine to achieve mirror finsih complete all as specifedand directed.

S&F pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50 mm thick of any colour as approved by GE having tensile strength of 550Mpa as in roof covering, fixed with self tapping screws complete all as specified & directed.

S&F pre-painted galvalume aluminium zinc coated GI based plain steel sheet or machine moulded profile ridge/corrugated steel sheet ridge 0.50 mm thick of any colour as approved by GE having tensile strength of 550Mpa as in ridge, fixed with self tapping screws complete all as specified & directed.

M&L for providing and injecting chemical emulsion for post construction anti termite treatment along the external wall below concrete or masonary apron using emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. In apron

S&F false ceiling with GI main snap grid of size 600x600 mm using main Tee of size 24x28x0.40mm prepunched to accept cross tee of size 24x28x0.40mm and wall angles of size 25x25x0.40mm fixed with wall around of size with and including 4mm thick plain fiber cement board white colour designer tiles as approved by GE of size 595x595 mm placed in the grid and held in position duly suspended by 4mm dia GI wire hanger from the roof with holding down clips, butter fly clips and necessary provision for light fixture etc complete as per manufacturers instructions complete all as specified & directed.

M & L for framed work for brakets, grid for ceiling etc. or similar work of angles or tees with web and flanges cut to shape drilled and countersunk for screw including bending and welding angles, as necessary, gussets plates, riveting, etc conforming to Fe-290 Gde E-165.

S&F in repair for 4 mm non asbestos fibre cement building boards fixed or laid/inserted to timber/steel/Aluminium framed with screws

M&L for ready mix plaster 15 mm thick on external wall/concrete surface and finished even and smooth complete all as specified & directed.

M&L for ready mix plaster 12 mm thick on internal wall/concrete surface and finished even and smooth complete all as specified & directed.

M&L for preparing newly plastered surfaces on walls and applying two coats of oil bound distemper over a coat of alkali resistant primer over 1mm thick wall care putty complete all as specified & directed.

M&L for complete removal of existing treatment on walls and applying two coats of oil bound distemper over a coat of alkali rsistant primer over 1mm thick wall care putty complete all as specified & directed.

M&L for complete removal of old decorated surfaces on walls using and applying two coat of cement base paint complete all as specified & directed.

M&L for preparing newly plastered surfaces on walls and applying two coats of cement base paint complete all as specified & directed.

M&L for preparation of new wooden surfaces of any description over 10cm in width or girth not otherwise described and applying two coats of syntethic enamel paint over a coat of pink primer complete all as specified & directed.

M&L for preparation of old painted wooden surfaces of any description over 10cm in width or girth not otherwise described and applying two coats of syntethic enamel paint complete all as specified & directed.

M&L for preparation of new steel & iron surfaces of any description over 10cm in width or girth not otherwise described and applying two coats of syntethic enamel paint over a coat of red oxide primer complete all as specified & directed.

M&L for preparation of old painted steel & iron surfaces of any description over 10cm in width or girth not otherwise described and applying two coats of syntethic enamel paint complete all as specified & directed.

S&F mild steel framed work such as grill, gratings etc gaurd barss; barred iron doors; ladders; doors/windows frames or gates of angle or other section conforming to Fe-290 Gde E165 with rail, braces, holdfast, etc complete incl fixing of hinges and fixing in position complete all as specified & directed.

S&F 35mm thick 2nd class HW (Hollock) plain framed panelled shutters (Minimum two panels) with lock rail and panels of 9mm thick BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces fixed in position complete all as specified & directed.

S&F 35mm thick glazed and skeleton shutters of 2nd class hard wood, open rabated and prepared to receive glass,gauge etc (with sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass, gauge etc complete all as specified & directed.

S&F Anodised aluminium powder coated door shutters,aluminium section weighing not less than 0.55 kg/ m including necessary joining cleats,glazing clips, ruber neoprene packing, aluminium handles 2 Nos 150mm long in each shutter, hinges 03 Nos 100mm long in each shutter, Tower bolt 02 Nos 150 mm long in each shutter, anodised aluminum snap beading screws etc. complete all as specifiedNote:-(Glass for doors and windows under this item shall be measured and paid seperately under respective item).

S&F powder coated Anodised aluminium window and without sash bars, aluminium sections weighing not less than0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no. each shutter). hinges type B-21 100mm long (2 no. each shutter) suitable handle (1 no. each shutter) complete all as specifiedNote:-(Glass for doors and windows under this item shall be measured and paid seperately under respective item).

S&F steel window with side hung shutter including box type hinges with steel handle and steel peg stay complete with glazing bar complete all as specified & directed.

All as per item No. 41.00 here-in-before but without glazing bars.

S&F steel ventilater top hung with shutters including box type hinges with steel handle and peg stays complete with glazing bars, dovetailed or welded complete all as specified & directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm thick PVC sheet reinforced with MS square tube and fitted in opening complete all as specified.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded pre-laminated PVC sheet having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined suitable PVC sheet beading and joined together with solvent cement and provision of partially louvered frame supply and fixing in the frame at site. Complete all as per specification & sample kept in GE office and as directed.

S&F stainless steel butt hinges 100 mm size complete all as specified & directed.

S&F aluminum anodized barrel tower bolts of extruded section of size 125 mm complete all as specified & directed.

S&F aluminum handles cast type anodised of size 150mm complete all as specified & directed.

S&F aluminium alloy, anodised, sliding door bolt (length of bolt 250 mm) with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified & directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads all as specified & directed.

M&L for 3mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 sqm in each pane complete all as specified & directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with steel wire staples, complete all as specified and directed.

S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with steel wire staples, complete all as specified and directed.

S&F for roof trusses (framed), trussed, purlins, rafters and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Fe-290 (Gde E-165) complete all as specified & directed.

S&F in repairs vitreous china squatting pan 'Orissa' pattern,size 580X440mm, white, with intergral foot rests (excluding flushing cistern and flush pipe) including connection to trap & to flushing pipe,anti syphonage pipe etc incl making good to floor to match with adjoining area complete all as specified & directed.

S&F in repair PVC low level white flushing cistern, valveless syphonic action type 10 ltr capacity with inlet, ball valve, float and handle including PVC flush pipe 32mm dia bend and a pair of mild steel iron brackets of suitable size incl making necessary connection to water supply pipeline, complete all as specified & directed.

S&F in repair vitreous chinaware wash hand basin (WHB), white, size 550x400mm complete including provision of pair of mild steel angle iron brackets of suitable size duly painted, 32 mm dia chromium plated waste coupling, PVC waste pipe and cutting for pinning in ends of brackets in wall etc complete all as specified & directed.

S&F in repair vitreous china urinals, half stall type (back or corner wall type), size of 465 x 355 x 265 mm white (minimum), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flushing cistern with brackets, flush pipe, grating and union for discharge pipe and waste pipe complete all as specified & directed.

S&F in repair tubular towel rail 20mm dia, chromium plated, D type, 60cm long between flanges complete all as specified & directed.

Taking up or down 15 mm dia steel tubing and connection incl cleaning or removal from the site of work complete all as specified & directed.

Taking up or down 25 mm dia steel tubing and connection incl cleaning or removal from the site of work complete all as specified & directed.

S&F galvanized steel tubing, 15 mm bore, medium grade incl all fittings and short pieces, fixed complete to walls and ceiling or laid in floors, complete all as specified & directed.

S&F galvanized steel tubing, 25 mm bore, medium grade incl all fittings and short pieces, fixed complete to walls and ceiling or laid in floors, complete all as specified & directed by Engr-in-Charge.

S&F in repair for PVC connection 600 mm long with 2 nos brass check nuts, suitable for 15mm dia bore, complete all as specified & directed.

S&F in repair 15mm dia bib tap with crutch or butterfly handle, screwed down, screwed for iron pipe, fancy type, cast copper alloy, chromium plated long body with flange complete all as specified & directed.

S&F in repair 15mm bore dia fancy type, chromium plated stop valves / angle valves cast copper alloys, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions & fixed complete all as specified & directed.

S&F in repair gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed for 25 mm dia pipe (ISI Marked) complete all as specified & directed.

S&F in repairs 15mm dia pillar taps brass with capstan head chromium plated screwed down high pressure with or without lettered “hot/cold” with long screwed shank and flynut screwed complete all as specified and directed.

Dismantling of 100 mm cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified & directed.

S&F 100mm bore cast iron soil waste and vent pipe (Cast type) in any length with or without ears with cement joints fixed to walls or laid in floor etc complete all as specified and directed.

S&F 75 mm bore cast iron soil waste and vent pipe (Cast type) in any length with or without ears with cement joints fixed to walls or laid in floor etc complete all as specified and directed.

M&L cast iron floor trap 75 mm outlet diameter with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified & directed.

S&F cast iron 'P' or 'S' trap 100mm out let diameter including jointing to CI pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified & directed.

S&F in repair 100 mm bore CI bends (any radius) all as specified & directed.

S&F in repair 75 mm bore CI bends (any radius) all as specified & directed.

S&F in repair 75 mm bore CI bends (any radius) with oval access door all as specified & directed.

S&F in repair 75 mm bore cast iron cowls all as specified & directed.

S & F 100 mm dia (bore of pipe) branch pieces single (Tee with oval acess door) (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m deep in foundation etc in soft/loose soil complete all as specified and directed.

Returing, filling in including spreading levelling watering and well ramming in layers not exc 25 cm complete all as specified.

Removing excavated soil material exc 250m but not exceeding 500 m and depositing where directed complete all as specified.

S&F for 200 mm bore reinforced conrete pipes, classs NP-2 with one collar per length of pipe complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on brick surface finshed even and smooth using extra cement complete all as specified and directed.

S&F in repair rotational moulded ploythelene water storage tank (cylindrical, vertical with closed top) 1000 ltrs capacity (ISI Marked), hoisted and fixed in position complete all as specified & directed.

S&F in repair brass, float valves 25 mm dia high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed complete all as specified & directed.

M&L for impregnating cream for injection into masonary or concrete wall 230mm thick agaist capilary rising humidity/dampness, using rising bar super storng (product No 201) of chowgle building chemicals or quivalet in other manufactures as directed. Method of application:Medhodology (a) The surface must be sound, absorbent, clean, free of dust, oil, paint, curing agents, loose cement or lime plaster & conrete, debrish, or any separation layers. (b) The plaster must be knocked off at least 50cm beyond the visibly penetrated area. (C) Damaged mortar joints are to be scraped out to a depth of approximately 2-3 cm. All sharp edge/joints need to be levelled, loose concrete to be removed. (d) Drill boreholes at gound level horizontally, The boreholes are drilled horizontaly, The boreholes are drilled horizontaly into the masonary.

M&L for rough cast plaster, applying the under coat of cement and sand mortar 1:3 not less than 10mm thick while it is still in plastic state the roughcast mixture consisting of crushed stone size between 6 to 12 mm mixed with coarses sand and cement in the ratio of 1:1:1 shall be applied and finished even complete all as specified and directed.

M&L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement:4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layers @ 3Kg of cement per square metere, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nomina size) in panels with groove all around as per approved pattern including scrubbing and sashing, the top layer with brushes and water to exposed the stone chippings including forming groove of uniform size 15mm witde and 15mm deep in the top layer washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete all as specified and direted.

M&L for rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bads, sunk pabels, cornices, skirtings, drip moulds and similar work n exc 15 cm in width or girth; indluding ctting to edges, all mitres and stopped ends. etc.

M&L for roughening surface of old conrete floor by picking, sweepings clean and washing down with water to remove dust, etc complete all as specified and directed.

M&L for brushing neat cement slurry with 3.0kg of cement per sq meter complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 40mm graded stone aggregate) as cement concrete in surface channels and drains/ water trough etc. complete all as specified and directed.

M&L for 1mm thick mild steel plain black sheet in wall cladding, steel gates and similar work, cut to size holes punched, including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up mitred agles etc as required complete all as specified and directed.

M&L for providing PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in, fixing hold fast/coping and similar work all as specified and directed.

Demolition of reinforced cement concrete above ground floor

M&L for reincorced cement conrete concrete (Design mix) M-25 as in slab supported on walls, beams and columns in floors, roofs landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for reincorced cement conrete concrete (Design mix) M-25 as in beams cantilevers bressummers, lintels uover 1.50m span and the like complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over cut to length bent to shape required, including cranking, bending spirally for hooping for coloums, hooking ends and binding with and including mild steel wire (anealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 5mm dia and over upto and incl 10mm dia in stirupps, spacers and binders cut to length bent to shape required, including cranking, bending spirally for hooping for coloums, hooking ends and binding with and including mild steel wire (anealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Use and waste for formwork to sides and soffits of floor or roof beams, beam hauchings, girders, bressummers, lintels cantilevers shelves including supports overhangs, etc also beams etc. complete all as specified and directed.

Use and waste for formwork to soffits of slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) work in rough finished flat surfaces or conrete complete all as specified and directed.

Use and waste for formwork to edges of concrete flats, treats, breaks in flors, window cill concrete railings, opeings in concrete walls, floor and roof n exc 20cm wide and sides of RCC/PCC bands in walls horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar 1:3 on ceiling surface complete all as specified and directed.

M&L for applying two coats of white lime wash on ceiling surface after preparation of surface complete all as specified and directed.

Surface excavation n exc 30 cm deep and getting out in soft/loose soil complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (40mm graded stone aggregate) for sub base complete all as specified & directed.

M&L for sand bedding/cushioning under interlocking tiles floor complete all as specified & directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS-15658-2006 to 60mm thick M-35 Grade set and jointed with grey cement and pigment complete all as specified and directed.

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/sqm) land on primed surface by forced application complete all as specified.

M&L applying evenly a tack coat of industrial bitumen of grade 85/25 at the rate of 1.20kg per sqm including cleaning surface complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:3 on roof surfce using WPC as per manufactures instruction complete all as specified and directed.

Supply only liquid water proofing compound.

M&L for 4.8mm thick sheet glass, ordinary quality and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified & directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide prime on old/new Surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light/fan socket or power) complete including fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc and removing the material from site including making good the disturbed surface to match with the existing all as specified and directed.

Material and labour for concealed point wiring with PVC insulated unsheathed multistranded colour code copper conductor in PVC conduit with FRLS cable1.5 Sqmm size 1100 volts grade conforming to IS:694 in new GI boxes of 1.6 mm thick including one coat of synthetic enmelled black paint and providing new 3mm thick plastic laminated sheet cover of required colour fixed with brass screws and cup washers including single core stranded FRLS copper conductor 1.5 Sqmm PVC insulated cable as earth wire to common earth and connected to earth dolly and earth terminal box drawn in same concealed conduit all as specified and directed by Engr-in-charge for the following :-

One light/fan/Exhaust fan/bell point controlled by one switch.

All as per item No. 118.00 here in before but for One 5 Amp socket out let independent.

All as per item No. 118.00 here in before but for One 5 Amp socket out let on same board

All as per item No. 118.00 here in before but with 2x4 Sqmm and 1x2.5 sqmm cable for earth connection for one 3 pin socket outlet 15 amps independent board complete all as specified and directed.

S&F switch Piano flush type SP, one way 5 Amps

S&F switch Piano flush type SP, one way 15 Amps.

S&F socket outlet 2 in 1, 3 pin 5 Amps.

S&F socket outlet 2 in 1, 3 pin 5 and 15 Amps, flush type.

S&F celling rose 65x50 mm bakelite 2 to 3 terminal with bakelite body complete suitable for 25 volt

S & F in replacement Lamp holder with insulated body with back plate suitable for batten fitting complete all aaas specified and directed

S&F in replacement of 9 Watt LED lamp 6500K, complete all as specified and directed

S & F Building Street light fitting new generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP66 25W LED 6500k roadway luminaire with high power LEDs as light source and electronic driver along with a bracket of G.I pipe suitable of size NBV having approx length of 1.5 M bent to shape and fixed to wall with clamps, nut bolts etc of approxiate size complete all aaas specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F of bulkhead LED light fitting 10 Watt deep drawn anodised aluminium body, epoxy white powder coated, heat resistant prismatic glass cover with gasket complete all as specified and directed.

S&F of factory made epoxy polyester powder coated distribution board TP & N 4 way (VTPN MCCB DB) with metal double door (IP-43 protection) fabricated from minimum 1.6 mm thick CRCA sheet and fixed on wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with provn for DPX 160, 4 pole MCCB and ELM as incommer and 16 SP MCBs outgoings complete all as specified and conforming to IS: 8623 along with cable end box for above DB including taking down old DBs all as specified. NOTE :- (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

S&F in repair of factory made epoxy polyester powder coated distribution board SP & N 8 way fabricated from minimum 1.6 mm thick CRCA sheet with metal double door (IP-43 protection ) fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, eath bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as incomer and 6 SP MCBs as outgoings complete all as specified and conforming to IS: 8623 alongwith cable end box for above DB all as specified and directed. NOTE (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

Supply & Fixing single pole MCB 6 to 32 Amps, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for 'B' Curve 10 KA breaking capacity complete conforming to IS 8828 of 1996 including taking down old MCB's complete all as specified and directed.

S&F DP MCB 40 amp, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity and terminal box suitable upto 63 sqmm cable complete conforming to IS 8828 of 1996 all as specified.

Supply & Fixing single pole MCB 40 amp, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for 'B' Curve 10 KA breaking capacity and terminal box suitable upto 25 sqmm cable complete conforming to IS 8828 of 1996 as specified.

Supply & Fixing in repair MCCB 125 Amp 4 pole 16 KA at 415 V with fixed thermal megnatic release complete all as specified directed.

Taking dowan sub main wiring of any sizes

Supply, laying sub main wiring and drawing in and including 20 mm dia concealed PVC rigid conduits including cutting of chases for laying conduit making good the surfaces as per existing surfaces or as directed on walls 02 runs of IC x 6.00 sqmm (Main Cable and neutral) and one run of IC x 6.0 sqmm (as earth wire) of stranded copper conductor PVC insulated unsheathed cables of 1100 volts grade conforing to IS : 694 of 1990 complete including connection all as specified and directed.

Supply & Fixing ceiling fan regulator step type for 1200/1400 mm sweep ceiling fan including connections complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, burieddirectly in ground (earth pit not lessthan 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 connected to earthing test point all as specified or indicated including testing on completion all as specified and directed.

M&L for Taking down ceiling fan, ceiling cable removing fan blades and deposite in MES Yard complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

A R construction

SHIVA ENTERPRISES

M/s T.K. ENTERPRISE