PROVISION OF FURNITURE AT OFFICERS INSTITUTE AT VSN, NAGPUR

Amount

Chair Easy Cushion (FD-229) All as shown on drawing. All wood shall be seasoned first class hard wood Teak (MP). Legs of chair shall be of 55 mm x 25 mm in section at place under side arm rest tapering to the bottom of legs to 25 mm x25 mm in section. Front legs shall be joint by 50mm x25 mm in section rails provided below seat frame for the support of frame. Rear legs shall be 55mmx25mm in section below Arm rest and 25mmx 25mm in section at the bottom of legs. Rear legs shall be joint together by rear rails of 50mmx25mm in section provided at the bottom of seat frame. Seat frame shall have the rear horizontal out of section 70mmx40mm joining the sides of frame which shall be 70mmx40mm at the back and 25mmx25mm in sction near the front rail. The front rail of seat frame shall be out of 55mmx25mm in section teak wood. The seat frame shall be of size 510mm long in front and 480 mm long at rear and 575 mm deep. The top horizontal rail of back rest shall be out of 55mmx40mm and shall be 50mm x20mm. The Bottom horizontal frame of back rest shall be 55mm x 20mm in section. The sides of back rest frame shall join the seat of chair and shall be out of 70mmx25mm made to shape as shown on drawing. The arm rest out of 65mmx25mm in section and 610mm long shall be provided in shape as shown on drawing. Seat and back shall be woven with plastic cane of 2mm wide 0.4mm thick in Godrej pattern. Hard rubber rings/PVC toes shall be provided to bottom of all legs with screw. All wood surfaces exposed to view when placed in position shall be french polished with glossy finish. Rest all as per drawing. supply & fixing of new polyurathene foam cushion 550x525x75mm thick 32 density duly covered with upholsty fabric/tapesty cloth, with provision of ziper, approved shade/texture all as directed by Engr-in-charge.

Peg Table (FD/MAP/11) All as shown on drawing. Overall size shall be 450mm long, 300mm wide, and 380mm high. All wood shall be seasoned first class hard wood Teak (MP). Legs shall be made of 30mm x 50mm 362 mm high. Top shall be made of 18/19 mm thick prelaminated particle board with teak wood beading allround. Rubber/PVC shoes shall be fixed on legs. One Long rails wooden member of teak wood of size 20x40mm though not shown on drawing shall be provided for joining bottom rails of Peg table.All wood surface shall be french polished with high gloss finish.

Sofa Set 5 Seater with Cushioned (FD-281) All as shown on drawing. The set consist of one long piece of three seat and two small pieces of one seat each. All wood shall be of first class hard wood teak (MP). Legs shall be of 70mmx35mm in section made to shape as shown on drawing. Wooden arms shall be made to shape out of 35mm x 70mm in section teak wood. Fron and side rails shall be of 35mm x100 mm in section teak wood. 40mm x40 mm in section teak wood bearers shall be provided at the bottom of seat over which 50mm x 20mm wooden battens, 21 Nos, shall be fixed equaly spaced in the long piece meant to seat three. Back shall be made of frame of rails and styles of 70mm x 35 mm in section teak wood. The filling in the frame, thus made, shall be done with 14 Nos teak wood battens of 50 mm x 20 mm in section fixed equaly spaced in the long piece meant to seat three, 30mm x 50 mm teak wood rail shall be provided between back legs to support back frame. 100 mm thick cushion foam of 32 density covered with best quality tapestry cloth with zip shall be provided at seat as directed by Engr -in-charge. 100 mm thick cushion foam of 32 density 530mm x 500 mm (Three Pieces) covered with best quality tapestry cloth with zip shall be provided at back. 07Nos, 50mm x20mm in section teak wood battens shall be fixed equaly spaced in single piece seat. Back shall be made of frame of rails and styles of 70 mm x 35 mm in section teak wood. The filling in back frame of single piece shall be done with 04 Nos, 50mm x 20mm in section teak wood battens. The Legs and the frame shall be made for single piece seat as provided for long piece to seat three. The seat and back shall be of 100mm thick cushion of 32 density of size 530 mm x 500 mm. All wood surfaces exposed to view shall be french polished with glossy finish. Rest all as per drawing.

Table Centre two tier (FD-375) All as Shown on drawing. Overall size shall be 1200 mm long , 600 mm wide and 400 mm high. Legs shall be 40 mm dia anodized brass legs, four in number in one piece. The legs shall be joined in short and long sides with two numbers of 25 mm dia brass pipes of wall thickness 2 mm . The brass frame shall be 900 mm long and 450 mm wide. Vaccum rubber shall be provided at top of legs. The bottom of legs shall be covered with brass sheet of 1 mm thick sheet. The bottom of legs shall have PVC shoes. The top shall be 10 mm thick plate tinted glass (white colour) with corners rounded as shown on drawing. The edges of top of table shall be rounded off.

Table 900x600 with Drawer (FD-283) All dimensions, Shape and sizes shall be as shown in drawing and as specified. Over all size of table is 900x600x760mm. All wood work shall be of well seasoned 1st Class teak wood. Table Top shall be of 18mm thick prelaminated particle board exterior grade with 6mm thick beading of 1st class hard wood teak all round as per drawing. Drawer made out of 12mm thick teakwood planks and bottom of the drawer shall be of 6mm thick plywood BWR grade all as specified and as per drawing. All exposed wooden surfaces shall be French polished. All joints fixing shall be done in accordance with standard workmanship and specifications.

Bar Stool Revolving With Hydrolic System (TP)

Display Case with Mirror of size 1850mmHeight x 450mm Depth x 1400mm Width with 03 Shelves and 04 Door. Thickness of Top & Sides 18mm, Thickness of Shelf 10mm. All wooden surfaces shall be french polished. Rest all as per specified and directed. (TP)

Receiptacle PVC with Bucket 15-20 Ltr Make: Nilkamal Material- HDPE, Bin Capacity-20Ltr (10+10 Ltr), Lid-Removable, Wheel-Without Wheel (TP)

Chair CBA Steel With Arms (FD-75(M) ) Overall size shall be 535mm wide 560mm deep and 900 mm high. Seat shall be 455mm high from floor. Conduit pipe used for frame shall be 20mm dia steel tubing having wall thickness 1.6mm. Welding of frame where required shall be as directed by GE and running welding grinded to give smooth surface. Wood for seat and back, where caning is to be done, shall be of first class hard wood teak. Wood for handles shall be of teakwood. Weaving of cane shall be done with premier or shah brand 2mm plastic cane in godrej pattern 4mm for boarders. Gola type weighing not less than 6gms per 10 running meter. Wood surfaces of seat and back and haldles shall be painted with high gloss paint, black in tint, before caning. Painiting shall be done with spray machine after preperation of wooden surfaces. All iron surfaces exposed to direct view when placed in position shall be painted with coats of enamel paint of primer after preperation of steel surfaces. Painting shall be done with spray machine to achieve smooth surfaces. Bottom of legs shall have hard rubber shoes. Flat iron strips 20mmx3mm, two numbers in each seat and back shall be welded to frame of chair as directed by GE.

Chair Varandah (FD-359) All as shown on drawing. Overall size shall be 460mm long, 600mm wide and 760mm high. Legs shall be made of 20mm dia mild steel conduit of wall thickness 1.6mm slanting 70mm horizontally for a verticle height of 355mm at front up to seat level. The horizontal distance between legs level shall be 450mm and between bottom of legs shall be 600mm. The rear legs shall be slant 80mm horizontally for 300 mm height at the back of seat level to bottom of rear legs. The seat frame shall be welded to the frame of legs. The seat frame with back seat shall be of continuous 20mm dia mild steel conduit of wall thickness 1.6mm two 20mm dia mild steel tube conduit shall be welded at the back rest and the rear of seat in such a way that weaving of cane plastic 4mm white as per Godrej Pattern shall be as directed by Engineer-in-charge. A 10mm dia mild steel round bar rod welded to front legs at 75mm front bottom of seat shall be provided as shown on drawing.

Tepoy Varandah (FD-255) Overal size shall be 900mm long, 450mm wide and 400mm high. Legs shall be made of 20mm dia mild steel conduit of wall thickness 1.6mm made in u shape with bottom of legs in sides shall be 350mm apart. U shaped legs shall be provided at 50mm from each end of long side, 25mmx3mm flat iron frame shall be welded on the top of conduit as shown on drawing. Irrespective of whether shown on drawing or no, the 20mm dia wall thic kness as 1.6mm, bottom stiffners to short sides connected to legs in shorter sides shall be welded at 100mm high from bottom of legs. A long stiffner with 20mm dia and wall thickness 1.6mm shall be welded with short stiffners joining short stiffners in the middle at 100mm high from bottom of legs. Top of table shall be 19mm thick particle board commercial over 1.5mm thick plastic laminated sheet of white colour shall be fixed as directed by Engr-in-charge. 3mm thick teakwood edging shall be provided al-round the top of the table. All steel and iron surfaces exposed to view when placed shall be painted with two coats of white enamel paint over a coat of primer after preperation of surface as directed by Engr-in-charge. The under side of top of top of table shall be painted with two coats of white paint over a coat of primer. 1.5mm thick plastic laminated sheet shall be provided over a teakwood edging. Hard rubber/PVC toes shall be provided to the bottom of all legs. And all as shown on drawing.

Stool Dressing (FD/E6/MAP/14) All as per drawing. Overall size shall be 440mm long 350mm wide and 425mm high prelaminated MDF board shall be used. Plywood 12mm BWR quality make Greenply/Kitply/Century shall be provided for openable shutter along with folding handle as directed as specified. 75 mm 40 density cushioned covered with leatherite shall be used as specified and as directed. 50 mm dia heavy duty revolving nylon wheel shall be provided at the bottom.

Table Dressing Ladies with Mirror (FD/MAP-II/07) All as shown on drawing. Overall size 1150 long and 1700 mm high. Mirror shall be 5mm thick electro copper plated made of Modiguard/Atul/Saint Gobin. Two shutter shall be made and provided megnatic catcher with each shutter and used 75mm long D shaped CP steel handle. In drawer 50mm long D shaped stainless steel handle shall be provided. 6mm thick plywood BWR make Greenply/Kitply/Century shall be used in back of mirror. Body work shall be made of prelaminated Particle board with beading of teak wood. All wood shall be polished with french polish with glossy finish. All as specified and directed.

Receiptacle Large 80 Ltr (TP) Materials- Stainless Steel, Bin Capacity-80 Ltr, Lid=Swing Type, Wheel-Without Wheel

Stool Steel (FD-81(M) All as shown on drawing. Overall size shall be 305mmx305mmx510mm. 18 Gauge MS Sheet for top and angular frame shall be provided.

Table Cook House Large W/Aluminium Top (FD-297) All as shown on drawing. Overall size shall be 900mmx540mmx840mm. All wood shall be of first class hard wood teak. Four leg shall be60mmx35mm in section 815mm high. Legs shall be joined togeather at top 25mmx75mm toprails in long and short sidesAwooden stiffener50mmx25mm shall be provided in the middle of long top rails joining the top long rails. 6mm dia mild steel lugs 35mm long embedded in legs by 25mm and protrding 10mm above legs shall be provided on top of all legs. The top of table shallproject 25mm from sides of legs in shortand long direction.25mm thick teak wood particle boardnshall be provided at the topmover which 22 gaurd aluminuim sheet shall be fixed bening on edges and further bending 10mm under the top of the table.All exposed wooden surfaces shall be French polished. Rest all as per drawing.

Side Board Large (FD-241) All as shown on drawing. Overall size shall be 1025mm long, 450wide and 750mmhigh. Back shall be 1025nnm long and 750mm high pre-laminated particle board 19mm thick. Sides shall be 450mm wide and 675mm high particle board 19mm thick. Base shall be of 75mm high 19mm thick pre-laminated particle board fixed at 25mm from front and sides. Top and bottom shall be of 19mm thick pre-laminated particle board. A vertical partition 19mm thick pre-laminated particle board shall be provided at 358mm from inside of right hand side pre-laminated particle board. Four drawers shall be provided equally in this space. Three piece of particle board 40nnmx19nnm and 358mm long shall be provided over the lower three drawers. Bottom, sides back of drawers shall be of 19mm thick particle board. The front of drawers shall be of 19mm thick pre-laminated particle board/ 18mm thick MDF. 20mmX2Omm teak wood bearers fixed exactly in center of both sides of the drawers shall be provided to each drawer. Another 20mmx2Omm teak wood bearer shall be fixed to the vertical of the side board in such a way that the bearers fixed with the sides of the drawer shall side over smoothly. On left side compartment two horizontal shelves, equally spaced shall be provided as shown on drawing. The size of shelves shall be 610mm long, and 387 mm wide. Two side hung shutters shall be provided to left hand side of side board. The shutters shall be side hung with 20mm size piano type hinges. The shutters shall be of 19mm thick pre-laminated particle board. 4mm thick teak wood edging shall be provided al-round the front shutters and front of shelves. Shelves shall be fixed over the standard aluminium shelf support. On ail visible front edges of pre-laminated particle board shall be provided with 4nnm thick teak wood edging. All drawers and shutters shall be provided with one handle each of powder coated mild steel and 100mm long. Two catch spring shall be provided to shutters as directed by Engineer-in-Charge. All wood surfaces exposed to view when placed in position shall be given high gloss French polish with lacquer finish.

Table Serving/Pantry (FD-295) All as shown on drawing. Overall size shall be 900mm long, 550mm wide and 840mm high. Size of steel frame shall be 880x515x815mm. Legs shall be four in numbers . Legs shall be of 25 mm square mild steel tube of wall thicness , 1.6mm and 815mm high. Top of laegs shall be joined together in long and short sides with top rails of 25 mm square mild steel tube of wall thickness 1.6mm. Two sides stiffners 465mm long shall be provided at 100mm from bottom of legs. The stiffners shall be 25mm square mild steel tube of wall thickness 1.6mm. A long stiffner shall be provided in the middle of short stiffners joining short stiffners with 25mm sqare mild steel of short stiffners joining short stiffner with 25mm square mild steel tube of thickness 1.6mm. Two drawers of equal size shall be provided at the bottom of top of table. All steel sheet used for drawerrs and side covering of drawer shall be mild steel and 1mm thick. Top of the table shall be 25mm thicck polished Kotah stone slab in piece. Legs shall be provided with hard rubber PVC toes at bottom. All steel surfaces exposed to view when placed in position be given two coats of primer after prepertion surface, Painting shall be done with spray machine.

NIHAL ENTERPRISES

Veer Brothers