PROVISION OF GUARD HOUSE WITH 02 SENTRY POST AND ALLIED SECURITY INFRA UNDER GE (NORTH) BANGALORE

Amount

Surface excavation not exceding 30 cm deep and averaging 15 cm deep and getting out Hard/Dense soil complete all as specified and as directed.

Removing excavated material exceeding 50m and but not exceeding 200m depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Excavation in trenches, not exceeding 1.5 m wide and not exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, for laying cables , Poles, laying water supply lines etc not exc 10 sq m on plan and not exc 1.5 m in depth and getting out Hard/Dense Soil complete all as specified and as directed.

All as per tiem No 1.003 herein before but depth exceeding 1.50m but not exceeding 3.0m complete all as specified and as directed.

Material and Labour for ATT for Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

Material and Labour for ATT for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured)complete all as specified and as directed.

Material and Labour for ATT for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed.

Material and Labour for ATT for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

Material and Labour for Cement concrete in in surface channel, foundation filling and mass concrete type D-2 1:4:8 (40mm graded stone aggregate)complete all as specified and as directed.

Material and Labour for Reinforced cement concrete (design mix M-25 grade using 20mm graded stone aggregate) in Foundations footings, plinth beams, bases for columns, etc and mass concrete complete all as specified and as directed.

Material and Labour for Reinforced cement concrete (design mix M-25 grade using 20mm graded stone aggregate) above top of footings including attached pilasters and buttresses complete all as specified and as directed.

Material and Labour for Reinforced cement concrete (design mix M-25 grade using 20mm graded stone aggregate) Columns, pillars, piers, posts and struts complete all as specified and as directed.

Material and Labour for Reinforced cement concrete (design mix M-25 grade using 20mm graded stone aggregate) Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

Material and Labour for Reinforced cement concrete (design mix M-25 grade using 20mm graded stone aggregate) Chajjas complete all as specified and as directed.

Material and Labour for Formwork flat to sides of concrete foundations, footings, bases of columns, and plinth beams and similar work vertical or to batter complete all as specified and as directed.

Material and Labour for Formwork flat to sides of pillars, posts, struts, piers, columns and stanchions

Material and Labour for Formwork flat to sides Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and as directed.

Material and Labour for Formwork flat to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and as directed.

Material and Labour forMild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

All as per item No 1.019 herein before but 5mm dia and over up to and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed.

Material and Labour for Pre-cast cement concrete masonry in PCC 1:3:6 type C1 using 20mm graded stone aggregate with solid block, exceeding 10cm in width setting in CM 1:6 complete all as specified and as directed.

Material and Labour for Pre-cast cement concrete masonry in PCC 1:3:6 type C1 using 20mm graded stone aggregate with solid block, not exceeding 10cm in width setting in CM 1:4 complete all as specified and as directed.

Supply and Fixing of Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment of Fe-410 W (Gde - E-250) quality B complete all as specified and as directed.

Supply and Fixing of steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and as directed.

Supply and Fixing of steel work in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and as directed.

Supply and Fixing of steel work in wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Material and Labour for rendering 15mm thick in 2 layers with CM 1:4, 05mm thick with water proofing compound @ 3% by weight of cement, over 10mm thick cement mortar 1:6 under coat on external wall surfaces finishing the surface even and smooth all as specified and directed by the Engineer-in-Charge(WPC shall be measured and paid separately)

Supply only Liquid water proofing compound

Material and Labour for rendering 10mm thick cement plaster in CM 1:6 on internal wall surfaces finishing the surface even and smooth all as specified and directed by the Engineer-in-Charge

Material and Labour for Filling under floors or in foundations including watering and consolidation (Note:- Earth obtained from excavation should be used complete all as specified and as directed.)

Material and Labour for Hardcore of gauge n exc. 63mm, deposited, spread and leveled in layers not exceeding 10cm thick, watered and rammed to a true surface complete all as specified and as directed.

Material and Labour for 75mm thick PCC 1:4:8 Type D-2 as sub base complete all as specified and as directed.

Material and Labour for Coloured Non Skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl Screed bed or bedding layer of mortar 15 mm thick in CM 1:4 for laying floor finishes complete all as specified and as directed.

Material and Labour for Glazed ceramic tiles in vertical surfaces 350 x 250x 7 mm/ 450 x 350 x 7 mm/ 300x450x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over & incl 10mm thick in screed CM 1:3 on brick work or concrete surfaces to receive wall tiles complete all as specified and as directed.

Material and Labour for Anodized aluminium snap grid frame work for false ceiling using Aluminium sections incorporated in frame work conforming to IS 733, IS 737 andIS 1285. Snap grid frame work shall be fixed to ceiling with supporting hanger consisting of 6mm dia mild steel rod, J bolts with necessary bolts, nuts and washers all as manufacturer’s instruction. The main and cross tees shall be jointed at junction/crossings with anodized aluminium angle bracket of size as indicated, if not indicated it shall be 15mmxl5mmx1.5mm, weighing 0.12 Kg per running metre, fixed with sutiable mild steel, bolts nuts and washers, all as per manufacturer’s instructions. The snap grid (main/cross tee section) shall be supported at ends all along the wall with anodized aluminium angle of size as indicated, if not indicated it shall be 40mmx25mmx2mm, weighing 0.36 Kg per running metre.Size of the snap grid shall be as indicated. Including 4.0mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium frame work with screws fixed in ceiling flat or sloping complete all as specified and as directed

Material and Labour for Preparation of newly plastered surfaces and applying two coats of cement base paint over one coat of primer on walls including in narrow widths/ bands etc complete all specified and as directed.

Material and Labour for preparing surfaces of plasteres or un plastered and applying Two coats of Oil Bound Distemper over and incl priming plastered and other surfaces with alkali resistant priming paint on internal surfaces incl providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and as directed

Material and Labour for preparing newly plastered ceiling surfaces and applying three coat of white wash complete all as specified & as directed.

Material and Labour for Preparation of new or previously untreated steel surfaces & applying a two coats of synthetic enamel paint over a coat of red oxide primer over 10cm in width or girth, not otherwise described.

Supply and Fixing of Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Supply and Fixing of Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of sheet of any type and any thickness complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated material exc. 1.50 km but not exc. 5 km and depositing complete all as specified and directed.

Supply and Fixing of Powder Coated (minimum thickness of powder coating 50 micron) anodized aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified all as specified and as directed

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Chief.

Supply and Fixing of Anodised aluminium grill (anodized transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with CP, brass/stainless steel screws @ 200mm entre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodized aluminium standard section around the opening, all completes as per the requirement and direction of Engg-in-Charge

Supply and Fixing of Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing

Supply and Fixing of Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

Supply and Fixing of 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid rounded or chambered, put together with glue pinned at joints complete all as specified and directed.

Supply and Fixing of 35mm thick 2nd class Hard Wood rail and style plain framed, paneled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply and Fixing of 35mm thick 2nd class Hard Wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats complete all as specified and directed.

Supply and Fixing of Mild steel work as in Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; handmade sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165

Supply and Fixing of 4 mm thick sheet glass, ordinary quality and glazing with oil putty and glazing clips in metal frame and second class hard wood beading in wooden frames in squares not exceeding 0.5 Sqm in each pane

Supply and Fixing of 4 mm thick sheet glass, ordinary quality and glazing with oil putty and glazing clips in metal frame and second class hard wood beading in wooden frames in squares exceeding 0.5 Sqm in each pane

Supply and Fixing of figured glass pin head type 4mm thick ordinary quality and glazing with oil putty/beading in square not exceeding 0.5 Sqm in each pane all as specified.

Supply and Fixing of Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including necessary putting or beading all as directed

Supply and Fixing of Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples all as directed

Supply and Fixing of 18/19mm thick Prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work all as directed

Supply and Fixing of Butt hinges medium weight, cold rolled mild steel 100mm long and fixed to door frame and shutter duly welded/screwed complete all as specified and as directed

Supply and Fixing of Butt hinges medium weight, stainless steel 75mm long and fixed to door frame and shutter duly welded/screwed complete all as specified and as directed

Supply and Fixing of Aluminium anodized barrel tower bolt of extruded section of size 200mm long complete all as specified and directed.

Supply and Fixing of Aluminium anodized barrel tower bolt of extruded section of size 125mm long complete all as specified and directed.

Supply and Fixing of Extruded Aluminum handles 150mm size, fabricated type, anodised all as specified

Supply and Fixing of Extruded Aluminum handles 100mm size, fabricated type, anodized all as specified

Supply and Fixing of Floor door stopper 140mm long aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor complete all as specified directed

Supply and Fixing of Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified directed

Supply and Fixing of Mild steel sliding door bolts 300mm long, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed to steel door complete all as specified and directed

Supply and Fixing of Mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed

Supply and Fixing of Aluminium plate type II, Gate and shutter, hooks and eyes 100mm complete all as specified and directed

Material and Labour for Plain cement concrete Type B0, 1:2:4 (12.5 mm graded aggregate),coping ,as in hold fast and as in steel frame of window back filling and in roof kerbs of mud stops, rounded or chamfered on edges cills, steps etc, all as specified and directed by Engineer-in-Charge

Material and Labour for Preparation of New or previously untreated wood or wood based surfaces and applying two coats of synthetic enamel paint over a coat of pink primer on wood or wood based material over 10 cm width or girth all as specified and directed

Material and Labour for 18/20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) us?ing marble dust with admixture of pigment to match with shade of granite. all as specified and directed by Engineer-in-Charge

Providing edge moulding to 18-20mm thick Granite stone of any description of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete.

Supply and Fixing of rotational moulded polyethylene water storage tanks 500 ltrs capacity (cylindrical or vertical with closed top) hoisted and fixed in position icl. 25mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0mm-210gms./25mm-455gms/ 40mm- 690 gms) & 02 nos of Nipple (01x25mm & 01x20mm dia) suitable for HDPE water tank. (Minimum weight 15 mm-38gms/20mm- 45gms /25mm- 65gms), complete all as specified and directed by Engineer-in-Charge

Supply and Fixing of vitreous china water closet, pedestal type, white including Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern, seat cover etc, including connection to drain (or out going pipe) and to flushing pipe anti syphonage pipes etc complete all as specified and as directed by Engineer-in-Charge

Supply and Fixing of Wash basins, Vitreous China (flat back or angle back type) size 550x400, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe

Supply and Fixing of Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe)

Supply and Fixing of PVC low level flushing cistern,10 litres capacity, including PVC flush pipe of required length, 15 mm bore ball valve and PVC connection 300 mm and other accessories, complete all as specified and directed.

Supply and Fixing of 110 mm dia PVC (SWR) Pipe single socketed in any length with rubber ring joint laid in trenches/fixed on floor/walls including jointing with solvent cement all as specified and directed.

Supply and Fixing of 110 mm dia PVC (SWR) bends with access door any radius complete all as specified and directed

Supply and Fixing of 110 mm dia PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed

Supply and Fixing of 110 mm dia PVC (SWR) PVC (SWR) vent cowl complete all as specified and directed

Supply and Fixing of PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

Supply and Fixing of Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms)

Supply and Fixing of Soap dish, vitreous China white, approximate size 160x 160x90mm embedded in the wall complete all as specified and directed.

Supplying and laying of 25mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in to walls, ceilings or in floors etc, complete all as specified and directed.

Supplying and laying of 20mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in to walls concealed, complete all as specified and directed.

Supplying and fixing of CPVC outer diameter 25mm bore Brass Elbow complete all as specified and directed.

Supplying and fixing of CPVC outer diameter 25mm bore Brass Tee complete all as specified and directed.

Supplying and fixing of CPVC outer diameter 20mm bore Brass Elbow complete all as specified and directed.

Supplying and fixing of CPVC outer diameter 20mm bore Brass Tee complete all as specified and directed.

Supply and Fixing of 15 mm bore fancy type pillar tap cast copper alloy with capstan heads chromium plated screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipes in repairs complete all as specified and directed.

Supply and Fixing of 15 mm bore fancy type chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

Supply and Fixing of 15 mm bore fancy type, chromium plated with long shank and cup (concealed type) Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

Supply and Fixing of 15 mm bore fancy type, chromium plated Stop valves/angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

Supply and Fixing of in Brass chromium plated shower rose 125mm size with swivel joints, including fixing to steel pipe or union complete all as specified and as directed.

Supply and Fixing of PVC waste pipe, 32mm dia, for WHB, urinal etc, complete all as specified and as directed.

Supply and Fixing of PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

Supply and Fixing of Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed.

Material and Labour for PCC 1:3:6, type C2, (Using 40 mm graded stone aggregate), 75mm thick as in plinth protection/Sub base flooring, finishing surface fair and even, in panel supply and Fixing of illing joints with mortar, etc., complete all as specified and as directed.

Excavation over areas not exceeding 1.50m deep and getting out in Hard/Dense soil complete all as specified and as directed.

Material and Labour for Plain cement concrete 1:4:8, Type D2, (using 40mm graded stone aggregate), 100 mm thick in sub-base concrete to pavement complete all as specified and as directed.

Material and Labour for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed.

Material and Labour for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in foot path, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

Material and Labour for preparing newly or untreated surfaces of brick, concrete work of any description, not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of primer etc complete all as specified and as directed.

Material and Labour for Plain cement concrete (1:4:8), type D2, using 40 mm graded stone aggregate as in concrete bed to drain pipes including packing under and haunching in against the side of DWCP pipes after they are laid and tested suitable for 200 mm dia bore pipe complete all as specified and as directed

Material and Labour for DCWP (double wall corrugated GDPE pipes), 200 mm dia, class SN-8 conforming to IS 16098 (part-2) in 6 mtr length laid in trenches with couplers complete all as specified and as directed

Material and Labour for plain cement concrete (1:2:4) type B1 (using 20 mm graded stone agg) as in coping, benching of manholes and similar work etc complete all as specified and as directed.

Material and Labour for plain Cement concrete (1:3:6) type C2 (using 40 mm graded stone agg) in surface channels and drains complete all as specified and as directed

Material and Labour for precast reinforced cement concrete 1:2:4 type B1 (using 20mm graded agg) as in cover slab for man hole set in CM 1:4 complete all as specified and as directed.

Material and Labour for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished ,and reforming benching as required for 200 mm internal dia of pipe complete all as specified and as directed.

Material and Labour for rendering 15mm thick in CM 1:4, on fair faces of brick work or block walling surfaces finished even smooth without using extra cement and complete all as specified and directed by the Engineer-in-Charge.

Material and Labour for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement, including forms, moulds, mitred /stopped ends etc all as specified and directed by the Engineer-in-Charge

Wiring complete with 1.5 Sqmm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through and incl non-metallic rigid PVC conduit medium grade ISI marked incl accessories incl GI/ MS branded sunken boxes of suitable module concealed on walls including modular frame and cover of suitable module fixed with cadmium plated iron screws for housing modular type switches, switch socket outlets, fan regulators etc., incl provision of 1.5 Sqmm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed for the following :-(a)One light point controlled by one switch . Note for Item No 2.001 :- (i) The earth wire for the points in the same circuit can be looped from point to point. (ii) Earth wire shall be taken inside the conduit. (iii) Cost of terminal box is deemed to be included in the item rate quoted for point wiring (iv) Cost of a circuit of any length of cable from DB to any switch/ socket board to be included in point wiring.

(b)One fan/exhaust point controlled by one switch/regulator

(c) One 3 pin socket out let 5 A on same board

(d)One 3 pin socket out let 5 A on independent board

Supply and Fixing of LED batten suitable for indoor applications 18/20 Watts, 4 feet with extruded aluminium housing & integrated LED channel rectangular white arcylic cover complete with all accessories all as specified and directed. Make: Bajaj, Cat No.BCLAB 18 WH LED P or or equivalent make specified in P.S

Supply and Fixing of LED batten suitable for indoor applications 10 Watts, 2 feet with polycarbonate housing & integrated LED channel rectangular white arcylic cover complete with all accessories all as specified and directed. Make: Bajaj, Cat No.BCLSB 10 WH or equivalent make specified in P.S

Supply and fix Modular switch 1 way 6A, 1 module all as specified and directed.

Supply and fix Modular Socket, 6A - 2/3 pin combined 2 module all as specified and as directed.

Supply and Fixing of MCB SPN 240 volts 32 Amps complete all as specified and as directed

Supply and Fixing of MCB single pole 240 volts 6 to 32 Amps complete all as specified and as directed

Supply and fix Modular Fan step regulator, 120W - 2 module complete all as specified and as directed

Supply and Fixing of MCB DB SPN 4 way double door type 240 volts with 200 Amps rated bus bar as specified and as directed.

Supply and Fixing of MCB DB SPN 8 way double door type 240 volts with 200 Amps rated bus bar as specified and as directed.

Supply and Fixing of ceiling rose, surface bakelite type 65 x 50 mm, 2 to 3 terminals all as specified and as directed.

Material and labour for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of earth plate at a depth not less than 1.5 metre connected to galvanized earth lead wire 4 mm dia as earth lead up to 7.5 mtr long by means of nuts, bolts, thimbles, check nuts and washers etc made of galvanized iron connected to earthing test point all as shown in electrical plate No 3 of SSR Part-I 2010 and as specified or indicated and testing on completion incl earth work and excavation in any type of soil plain cement concrete (1:3:6) type C1 chamber, pre cost slab 40mm thick in cement concrete (1:2:4) type B1 with 8 mm dia MS bars reinforced at 10 cm centre to centre both ways incl funnel with watering pipe wire mesh and lugs, incl test point complete all as specified and as directed.

Supply and Fixing of 30W LED bldg security light fitting with pressure die cast housing along with prismatic polycarbonate diffuser with IP 66 protection. Make:- Bajaj, Cat No.:- ENXT P 30L WH SY PC SD or equivalent make specified in P.S

Supply and Fixing of Bracket made out of GI tubing medium grade 25 mm bore, approx length 1.5 m long including MS clamps made out of MS flat iron 25 x 6 mm, nuts, bolts, washers etc and including before fixing applying two coats of aluminum paint over a coat of red oxide primer complete all as specified and directed.

Supply and Fixing of ceiling fans with complete accessories, 230V, SP 1200 mm Sweep with BEE 3 Star rating complete with all accessories and fixing the fan from ceiling rose with 3 core flexible copper wire 24/0.20 sqmm, etc all as specified and as directed. Make Bajaj, SABSE TEZZ EE 03. Model No 251120 or equivalent make specified in P.S

Supply and Fixing of Exhaust Fan, steel body AC single phase, 230V of size 300mm Sweep with, blade and frame and louver all as directed. Make : Bajaj or equivalent make specified in P.S

Material and labour for sand cushioning with a layer of river sand 23 cm thick under and above the cable complete all as specified and as directed

Supply and Laying of sub class burnt bricks for cable protection complete all as specified and as directed.

Supply and Laying of XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured power cables (heavy duty) with aluminium conductor, 1100 volts grade, cross sectional area 16 Sqmm, 2 core laid in trenches/wall complete all as specified and as directed.

Supply and Fixing of GI tubing light grade 32 mm bore with all fitting laid in trenches/walls/Roads for cable protection complete all as specified and as directed.

Supply and Laying of galvanized iron steel tube, Medium grade 25 mm bore pipe, with all fittings laid under floors or in trenches/walls for external water supply complete all as specified and as directed.

Supply and Laying of galvanized iron steel tube, Medium grade 20 mm bore pipe, with all fittings laid under floors or in trenches /walls for external water supply complete all as specified and as directed.

Supply and Fixing of Gun metal Gate valve of size 20 mm dia with with iron wheel.

Supply and Fixing of Float valve of size 20 mm dia with PVC body aluminium float rod, nylon float high pressure type

S S BUILDERS

Forge Engineering & Electricals