REPAIR REPLACEMENT TO JOINERY PVC DOOR PVC CUPBOARDS PLASTERING TILING WORK SANITARY FITTINGS AND CERTAIN WORKS AT PARADE GROUND BHARATPUR MIL STN

Amount

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc complete all as specified.

M & L rendering 15 mm thick in CM (1:4) of brick on fair faces of work or concrete surfaces finished even and smooth without using extra cement, complete all as specified.

All as per item No 2 above but in CM (1:6) finished even and fair complete all as specified.

M&L for rendering 10mm thick in cement mortar 1:4 on concrete surfaces including finished even & smooth without using extra cement on ceiling complete all as specified.

M&L for Two coat of exterior emulsion paint on new plastered surfaces of walls, over a coat of primer white or tinted including preparation of surfaces complete all as specified.

M & L Preparation of new plastered surfaces of wall including cornices, pilasters etc by brooming down and applying two coats of cement base paint of approved shade on walls over a coat primer with hand roller complete all as specified.

M & L Preparation of new decorated plastered unplastered surfaces surface of wall including cornices, pilasters etc by brooming down and applying Three coats of white wash on walls complete all as specified.

M & L Preparation of new plastered surface of wall including cornices, pilasters etc by brooming down and applying two coats of oil bound distemper over a coat of prime and 1mm wall care putty(Two Coat) of approved shade on walls by roller complete all as specified.

M&L for three coats of white wash on new plastered or unplastered surfaces of Ceilings including prepration of surfaces complete all as specified.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoin jambs pillars etc.complete all as specified.

M&L Brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified.

All as per item No 11 above but except bricks complete all as specified.

Demolition of PCC in ground floors and pavings not exc 15cm thickness ( below or above ground level ) complete all as specified.

M&L for PCC 1:3:6 type C1 using 20mm graded stone aggregate as in plinth protection, 50mm thick finished even and smooth without using extra cement complete all as specified.

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in flooring 40mm thick finished even and smooth with using extra cement complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ), removing serviceable tiling to store and rubbish off the premises complete all as specified.

M&L Glazed ceramic tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 10 mm thick plaster in CM (1:4) complete all as specified.

M&L for coloured finish Non Skid Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm , over 15 mm thick screed bed in CM 1:6 in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

M&L for Vitrified Light Shade ceramic tiles 10 mm thick (Square/rectangular) area of each tile not exceeding 0.36 sqm , over 15 mm thick screed bed in CM 1:6 in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified.

Dismantling of stone slab and tiles of any description or thickness in floors, etc laid beded and pointed in any mortar complete all as specified.

M & L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms,Floor and like in cement mortar (1:4) including point?ing in white cement (1:2) us?ing marble dust with admix?ture of pigment to match with shade of granite over and including 15mm thick screed bed in CM 1:6 complete all as specified.

M&L for Machine cut kota stone slab flooring 20-25 mm thick over cement screed 20 mm thick in cement mortar 1:6, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for Machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dedo and pillar laid over cement screed 15 mm thick in cement mortar 1:4, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

Cutting, polishing to existing Kota/ marble flooring, and mirror polishing complete all as specified.

M&L for galvanised steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors including taking up or down the existing unserviceable GI pipe of following sixes :-

(a) 15 mm bore

(b) 20 mm bore

S&F in repairs bib tap, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15 mm bore complete all as specified.

S&F in repairs angle valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed of following size:-

(a)15 mm bore

(b) 20 mm bore

S&F in repairs.brass ball valve of 20mm bore, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed complete all as specified.

S& F in repair 15mm bore brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified.

S &F of triple layered (White Colour) rotational moulded polyethylene water storage tanks 500 Ltr (cylinderical vertical with closed top) with 20mm dia ball brass valves,high pressure , with polythene float and flynut including dismantling of existing water tank of capacity exc 250 Ltr & n exc 500 Ltr, complete all as specified.

S &F of triple layered (White Colour) rotational moulded polyethylene water storage tanks 1000 Ltr (cylinderical vertical with closed top) with 20mm dia ball brass valves,high pressure , with polythene float and flynut including dismantling of existing water tank of capacity exc 500 Ltr & n exc 1000 Ltr, complete all as specified.

S&F in repair of pillar tap, cast copper alloy with capstan heads,chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore complete all as specified.

S&F in repair vitreous china wash hand basin, white, of size 550x400mm flat back excluding taps, chain and plug but including waste pipe, brackets, cutting for and pinning in ends of brackets or erecting stand complete all as specified.

S&F waste fitting brass chromium plated for 32mm bore with long screwed shanks and fly nuts including 32mm PVC waste pipe for WHB complete all as specified.

S&F in repair of brass chromium plated shower rose 300mm size with swivel joint type including fixing to steel pipe of 15mm bore or union complete all as specified.

S&F in repair of PVC low level flushing cistern 10 ltrs capacity with inlet ball valve float & handle, syphonic action type including brackets & flush pipe of 32mm dia complete all as specified.

S&F in repair of aluminium anodised tubular towel rail, 20mm dia, 'D' type, 60cm long between flanges complete all as specified.

S&F in repair of 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, ISI marked complete all as specified.

S&F in repair of 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, ISI marked complete all as specified.

Taking down chowkats or frames n. exc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified.

Taking down shutter of any description area exc 1 sqm and n. exc 2 Sqm each complete all as specified.

Taking down chowkats or frames exc. 1.5 sqm but not exc. 4 sqm each without taking off shutters from frames complete all as specified.

S&F 35 mm thick 2nd class hardwood factory made plain framed, panelled shutters (any No. of panels) with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces size of members as per IS 1003 PtI complete all as specified.

S&F 35 mm thick 2nd class hardwood factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc.( without sash bars ), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc., sizes of members of shutters as specified in SSR Part I complete all as specified.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, door chowkats of angle or other section and similar works complete of Gde Fe-290 Gde E-165 including welding etc complete all as specified.

S&F windows made of Pre-painted steel(Base steel as per IS 513 of 0.58mm thick 'D' Quality galvanized as per IS 277 with zinc of 120 GSM) and Primer of 5-7 microns thick,finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alktd backer.Section for outer frame should be of 72x55mm,centre mullion should be of 72x50mm, section for fixed glass beading should be of 2x2mm and section for shuttter should be of 52x25mm. Outer frame & mullion sections to have rebate for glazed shutters. Fly mesh with 20mm GI flat beading for provision of guard bars/grills. Fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2 Nos of heavy duty stainless steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain floa glass and SS Mesh for fly mesh shutter with 0.36mm dia of wire and 1.40mm aperture. Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. including 12mm square quard bars with 110mm spacing c/c (Horizontal bay) to be welded on FI 20x6mm alaround except runner portion complete all as specified.

Hacking out old broken glass any thickness, size, quality or description from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads including S&F 3 mm thick plain sheet glass ordinary quality in square not exceeding 0.5 Sqm each pane complete all as specified.

S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified.

S&F 100 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete all as specified.

S&F 50 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete all as specified.

S&F150 mm long mild steel barrel tower bolts stove enameled black with bright bolt (ISI marked) complete all as specified.

S&F Mild steel pressed steel bow handle oval type stove enameled black of size 150 mm (ISI marked) complete all as specified.

S&F Small fitting such as brackets of any type latch and hinge blocks shapped door and window stops and the like n. exc 200 cucm each of second class hard wood including all necessary labour complete all as specified.

S&F MS sliding door bolt, plate type, 300mm long, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts & nuts, 4 on bolt plate and 2 on staple plate and fixed complete all as specified.

S&F in repair of mild steel 300 mm, ordinary rat tail rod pattern including roller and roller plate complete fixed to wooden/ angle iron chowkats complete all as specified.

M & L for Painting to new untreated steel surfaces of any description over 10 cm in width or girth with two coats of synthetic enamel paint over a coat of Zinc chrome primer including preparation of surfaces complete all as specified.

M&L for preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.-

S&F for sollid PVC door frame of size 50mmx47mm made out of 5mm plain colour pvc sheer reinforced with MS squre tube complete all as specified.

Supplying & fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as specified and shown on SSR 2020 (Part-II) complete all as specified.

S&F extruded aluminium alloy handle 150mm size fabricated type anodised, ISI marked complete all as specified.

S&F Aluminium anodised barrel tower bolt 150mm long of extruded section and fixed complete all as specified.

S&F 75 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete all as specified.

S & F powder coated Anodised Aluminium frame for door,windows,ventilator with one or more rebates including joining cleats for fixing etc complete all as specified.

M&L for powder coated aluminium glazed window/ ventilator shutters with frame openable using 100 x 45 x 2.00mm thick aluminium sec for frame & section for shutter 45 x 44.45 x 1.90 mm thick incl 5mm thick glass sheet with rubber beading clip,including 75mm Al hinges (02 Nos) 100mm Aluminium handle(01) nos and 100mm Al tower bolt(02 Nos) in each shutter etc complete all as specified.

S&F powder coated Aluminium door partly glazed (using 5mm thick glass) and partly panelled (using 12mm thick both side prelaminated board ) door with bottom rail of section 114x44.5x1.5mm thick and middle and top rail and style of section 84x44.45x 1.5mm thick incl 125mm dia circular aluminium handle and 150 mm tower bolt, mortice lock of brass size 65mm, vertical type with fair levers door stopper double leg rubber beading and door double action floor spring of approved make, two numbers door stopper, and aluminium frame of section 100x44.45x2.00mm thick complete all as specified.

M&L for sheet glass ordinary quality 4.8mm thick and glazing with oil putty in square exc 0.50 sqm in each pane complete all as specified.

S&F in repair/Replacement double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box,main body with stainless steel cover,governing pivot made of brass,other parts made of mild steel heavy duty and fixed complete all as specified.

S&F in repair Aluminium extruded section body door closer hydraudically regulated designation no 3 universal type suitable for door shutter up to 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation, boards/slabs/blankets, any thickness, including cover fillets and frame work complete all as specified.

S&F PVC wall panelling with panel of 300 mm x 6 mm Hollow section of Sintex pattern SPUF- 146 or equivalent , fixed with PVC plug and screw and inserted to next panel groove, edges and corners of all door/ window/openings etc to be covered with PVC angle fixed with solvent cement complete all as specified.

M&L for providing and fixing Gypsum Board 12 mm thick in ceiling fixed with screws complete all as specified.

S&F anodised aluminium snap grid frame work of size 605x605mm for false ceiling complete all as specified.

S&F hangers 6mm dia. G.i. (up to 1200 mm length ) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3mm size 60 mm long and hold fasterners 12.5mm dia 40mm long. complete all as specified.

GOVIND CONSTRUCTION (BID ID -3341940)

Tulsi Enterprises (BID ID -3341704)

MS Kumar and Brothers (BID ID -3341461)

Swastik Engineering Works (BID ID -3341892)

M/S MAMTA CONSTRUCTIONS (BID ID -3341656)

K P BUILDERS (BID ID -3332303)

VASUNDHARA AND COMPANY (BID ID -3341798)

krishna Associate (BID ID -3338790)