REPAIR REPLACEMENT OF FITTING OF FIXTURE INTERNAL WIRING SUMMER AND COOLING APPLIANCES WATER SUPPLY MISC E M WORKS OF UNIT 365 AT MIL STN BIKANER

Amount

REPAIR TO REFRIGERATORS Taking down unserviceable compressor including bushes, grommets sleeves, washers, mounting rubbers, nuts, bolts terminal cover brazing and clips from existing refrigerators complete all as specified and as directed.

Supply and fixing new hermetically sealed unit (compressor) including provn of new bushes, grommets, sleeves , washers , mounting rubbers nuts and bolts , terminal covers, brazing and clips of existing make and capacity in the existing refrigerator for 180 to 230 ltr capacity. Make : Emerson/LG/Godrej/Tecumseh/kirloskar.

Supply and fixing new hermetically sealed unit (compressor) including provn of new bushes, grommets, sleeves , washers , mounting rubbers nuts and bolts , terminal covers, brazing and clips of existing make and capacity in the existing refrigerator for 310 to 450 ltr capacity. Make : Emerson/LG/Godrej/Tecumseh/kirloskar.

Servicing and Cleaning of refrigerator complete existing gas system with CTC, testing of leakage, charging of refrigerant with R-134 (a), R-600, Hydrocarbon after rectification of leakage in existing refrigerators of 180 to 310 ltrs capacity of make and model as per existing complete all as specified and as directed.

Taking down carefully the following accessories /parts from existing refrigerator of any make and capacity , supply and fixing accessories/parts as per existing in the same Refrigerators as under:- Evaporator for refrigerators existing size and make.

Filter suitable for refrigerators existing size and make

Capillary tubes of copper existing sizes as per sample.

Door gasket

Freezer door supports with frame for the refrigerator any capacity.

Supply and fixing thermostat for refrigerator any capacity Make Indfoss or equivalent

Supply and fixing relay for refrigerator any capacity Make : Godrej Hi- Tech

Screw or pin type lamp for refrigerator as per sample.

REPAIR TO WATER COOLERS Taking down unserviceable compressor including bushes, grommets sleeves, washers , mounting rubbers, nuts, bolts terminal cover brazing and clips from existing water coolers of Make : Voltas /Usha/Sidhwal / Blue Star 40/80 ltrs , 60/120 ltrs , and 150/150 ltrs capacity complete all as directed.

Supply and fixing new hermetically sealed unit (compressor) including Provn of new bushes , grommets, sleeves, washers, mounting rubbers , nuts and bolts, terminal covers, brazing and clips and necessary accessories for water cooler 150/150 Ltrs . Make : Emerson/LG/Godrej/Tecumseh/kirloskar.

All as per item Ser No 13 for water cooler 60/120 ltrs Make : Emerson/LG/Godrej/Tecumseh/kirloskar.

All as per item Ser No 13 for water cooler 40/80 ltrs Make : Emerson/LG/Godrej/Tecumseh/kirloskar.

Taking down carefully existing internal wiring of existing water coolers and in lieu Provn of new internal wiring with PVC insulated copper conductor of size 40/0.0076 sqmm including replacement of main lead 03 meter long ,terminal clips , thimbles, 03 pin plug top 15 amps & soldering extra complete all as specified. Make of wire Plaza/Finolex/havell's.

Taking down carefully the following accessories/ parts from the existing water coolers and in lieu providing new accessories / parts in these water coolers as per details given below:- Filter copper.

Capillary tube of copper existing size as per sample.

PVC water out let pipe 15 mm dia including clamps

Drain pipe of same quality, length and dia meter as per existing.

Supply and fixing in replacement new condensing unit size12” x12”/12” x 15” or nearest size as per extg.

M & L Cleaning of complete existing gas system with CTC, testing of leakage, charging of refrigerant with R-134 (a) , R-22 after rectification of leakage in existing water coolers any capacity complete all as specified and as directed .

Taking down carefully fan motor from existing water coolers and in lieu providing new fan motor 1/35 HP 230 volts, 50 HZ, including replacement of mounting legs complete all as specified . Make of fan motor:-Frac Master / Polor

Taking down carefully fan motor from existing water coolers and in lieu providing new fan motor 1/16 HP 230 volts, 50 HZ, including replacement of mounting legs complete all as specified .Make of fan motor:-Frac Master / Polor

Taking down carefully fan motor from existing water coolers and in lieu providing new fan motor 1/10 HP 230 volts, 50 HZ, including replacement of mounting legs complete all as specified .Make of fan motor:-Frac Master / Polor

Taking down carefully fan motor from existing water coolers and in lieu providing new fan motor 1/25 HP 230 volts, 50 HZ, including replacement of mounting legs complete all as specified .Make of fan motor:-Frac Master / Polor

Supply and fixing in replacement push cock (Stainless steel) for water cooler as per sample and existing size.

Supply and fixing thermostat for water cooler of any capacity and Make as per existing

Supply and fixing relay with OLP suitable for water cooler Make Annapurna/ Hi Tech

Supply and fixing running capacitor 36 MFD Make : Tibcon/Sharda /Epcos

Supply and fixing capacitor 40/60 MFD, 80/100 MFD, 60/80, 100/120 as per site requirment Make : Tibcon /Sharda /Epcos

Supply and fixing capacitor 10 MFD/15 MFD as per site requirment Make : Tibcon/ Sharda/Epcos

REPAIR TO DESERT COOLERS Removing of old paint complete with emery paper and cleaning with scrapper and preparation of internal surfaces & bottom of the desert coolers and apply one coats of black bituminous paint complete all as specified

All as per item No. 33 here in before but applying spray painting with synthetic enamel paint to external surfaces of desert coolers including steel grills, side panel etc complete all as specified amd as directed by engr-in-charge. Make of paint burger/asain and colour as approved

Taking down carefully old unserviceable water pumps heavy duty of capacity 1/70 HP , 230 volts 50 HZ single in lieu providing new submersible type water pump

Taking down carefully fan motor from existing desert coolers and in lieu providing new fan motor kit 1/6 to 1/8 HP 230 volts 50 HZ including replacement of mounting legs complete all as specified and directed. Make : Khaitan/ Indo/ Cool Home/victor/CG.

S&F in replacement the following parts:- Capacitor for desert cooler 4 MFD 230 volts Make: Asian/ Tibcon/ Epcos.

PVC front grill including nuts bolts and washers suitable for 18/20” sweep existing desert coolers. Make Alka/Konark.

Taking down part of desert cooler old rusted as under and M & L 20 gauge GI plain sheet class -III including cost of riveting welding, nuts and bolts as required for fixing etc complete all as specified and as directed. Bottom tank comlpete as per existing size.

Top cover as per existing size.

M & L Side panels as per existing size.

Wood wool pad for desert coolers (set of three) any size as per site requirement approved by Engr-In-charge.

Supporting Jali for desert coolers (set of three)

Plug Top 3 pin, 15-A, 230 Volt

Fan blades mode of aluminium for Desert cooler as per sample.

Taking down unserviceable compressor form deep freezer including bushes, grommets sleeves, washers , mounting rubbers, nuts, bolts terminal cover brazing and clips from existing deep freezers of capacity 320 Ltr, Make : Voltas /Usha/Sidhwal / Blue Star complete all as directed.

Supply and fixing Compressor suitable for deep freezer 320 ltrs with necessary accessories including Provn of new bushes , grommets, sleeves, washers, mounting rubbers , nuts and bolts, terminal covers, brazing and clips.Make : Emerson/ LG/ Godrej/Tecumseh.

Cleaning of complete deep freezer existing gas system with CTC, testing of leakage, charging of refrigerant with R-134 (a), R-600(a) after rectification of leakage in existing deep freezer of any capacity ,make and model as per existing complete all as specified and as directed.

REPAIR TO AIR CONDITIONERS Taking down unserviceable compressor 2TR capacity from the window /split AC of any make and Supply & fixing new compressor 2.0 Ton capacity including bushes, grommets, sleeves , washers , mounting rubbers , nuts , bolts , terminal covers , brazing and clips from existing AC complete all as specified and directed. Make : Emerson/LG/Godrej/Tecumseh/kirlosar.

All as per item No 49 here in before but for window/split type AC 1.5 TR capacity.

All as per item No 49 here in before but for ductable type AC 5.5 TR capacity.

Cleaning of complete existing gas system with CTC, testing of leakage, charging of refrigerant with R-32, R-22,R407,R-290 ( as Per Site reqirement) after rectification of leakage in existing window type/Split type Air Conditioners of 1.5 TR capacities of make and model as per existing complete all as specified and as directed.

Cleaning of complete existing gas system with CTC, testing of leakage, charging of refrigerant with R-32, R-22,R407,R-290 ( as Per Site reqirement) after rectification of leakage in existing window type/Split type Air Conditioners of 2 TR capacities of make and model as per existing complete all as specified and as directed.

Cleaning of complete existing gas system with CTC, testing of leakage, charging of refrigerant with R-32, R-22,R407,R-290 ( as Per Site reqirement) after rectification of leakage in existing window type/Split type Air Conditioners of 5.5 TR capacities of make and model as per existing complete all as specified and as directed.

Taking down of old unserviceable fan motor of any capacity from the window/split type Air Conditioners 1.5/2/5.5 TR capacity and dismantling old and Proveding new fan motor of existing gauge and size complete all as specified and as directed.

Supply and fixing running capacitor 45 MFD Make : Tibcon/Sharda / Epcos

Supply and fixing in replacement Plug and socket DB with earth plug and 2 pin suitable for AC including one MCB SP 32A Make: Legrand Ct No 607851/schineider/ABB.

Supply and fixing capacitor 6 MFD Make : Tibcon/ Sharda/Epcos

Supply and fixing capacitor 50 MFD Make : Tibcon/ Sharda/Epcos

S & F PCB (Printed Circuit Board) of window/ split type AC of capacity 1.5/2/5.5 tonnes with warranty of 1 year complete all as specified and directed by Engr-in -Charge.

Replacement of remote of 1.5/2/5.5 Ton capacity window/split AC of any make / type all as specified and directed by Engr in Charge.

Taking down existing AC window/split type any capacity, cleaning, washing complete by water spray carefully and refixing the same in position after replacement of filter compelte all as specified and as directed.

servicing and cleaning of air washer of size 15500/14500/10500/8000/7000 CFM,replace 200mm thick cellulose paper pad cooling media , water pump , distributor with interconnect piping , PVC eliminator , pre-filter , repair/ replacement of three phase induction motor of any size and make

REPAIR TO walkin cooler : Taking down of any size unserviceable compressor 01 ton capacity walkin cooler of any make and supply & fixing new compressor 01TR capacity of walkin cooler including gas charging , fan blade , fan motor any size, evaportator unit , condenser unit with connecting accessiers etc. and recommended by existing O.E.M.

REPAIR TO GEYSER Taking down and opening of the geysers 25 ltrs capacity any make complete for inspection descaling by chemical treatment of internal parts such as steel inner tank, siphon assembly, heating element, etc re-assembling and refixing the same to its original position after testing on pressure complete all as directed by the Engineer-in-charge. Note :- Items such as glass wool, steel inner tank, siphon assembly etc if found unserviceable under above item will be measured and paid for separately under its relevant item.

Supply and fixing in replacement glass lined inner tank for capacity of geyser 25 ltrs as per existing size and shape. Make : Bajaj/Marc or equivalent

Supply and fixing in replacement siphon assembly suitable for 25 ltrs Geysers, with rubber washer of suitable size.Make : Marc/Bajaj/Polar or equivalent

S&F in repair hot water pipe 15 mm bore 60 cm long with brass unions one(Chromium plated) one on each side. Pipe shall be as per I.S for 15 mm bore of pipe for 25 ltrs capacity Geysers.

S&F in repair Thermostat switch I.S.I marked, to Geysers 25 ltrs of any make / size and shape as per site requirement

S&F Low density polythene pipe (LDPE) connection arrangement with pipe of pressure rating 2.5 kgf/cm2 , 15 mm bore 30 cm to 45 cm long with brass unions one(Chromium plated) one on each side in repair to Geysers 25 ltrs. Pipe shall be as per I.S.I

Supply and fix in replacement heating element of rating 1.5 KW capacity including washers for 25 ltrs capacity Geysers.Make :- “Marc/THETA/ ALERT”

Supply and fix in replacement Indicator lamps as per existing type having red or green coloured reflector all as specified and directed by Engineer-in-Charge

Supply and fixing in replacement flexible, 3 core PVC insulated copper conductor cable of size 40/0.0076 with over all PVC insulation ISI marked.

Supply and fixing in replacement pressure release valve suitable for 15 mm bore of pipe for 25/ 35/50 ltrs capacity Geysers.

Supply & fixing in replacement bib cock cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified.

Supply and fixing in replacement stop cock cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified.

Servicing and cleaning of solar panel tube , hot water tank by removing all the bird disposal, dust and other migrated disposal deposited on panel tube both inside and outside including renewal of all the washers nut bolts, screw, union complete all as per specified and directed

S & F in replacement borosilicate glass tube for solar water heater 3.3 with high impact resistance to hail strom evacuated tube of length (1600mm,1800mm,2100mm) , out tube dia 47mm to 58mm , inner tube dia 37mm to 47mm and glass thickness 1.6 ± 0.15 and weight 1.3 Kg to 1.8 Kg single tube complete as per site requirment and sample approved by Eng-In-Charge and GE also. Note :- Glass tube shall be approved by Engineer-In-Charge and as per site requirement contractor shall provide the size of glass tube.

S&F in replacement Rotational moulded polyethylene water storage tanks of 1000 Litres capacity triple layers ISI marked , (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc complete all as specified and as directed by Engr-in-Charge.

Lagging to pipes used in hot water supply or plumbing all around with 25mm thick, bounded mineral wool performed 'SNAP ON' pipe sections of density 144 Kg/Cum confirming to IS 9842 on outer side of hot water pipe line of 20mm bore including bend with 0.1 mm aluminium foil complete all as specified and directed.

Supply & filling distilled water inside solar water storage tank as heat exchanger agent and solar water battery complete all as specified and directed

M & L in replacement heating element of rating 3.0 KW suitable for solar water heater make : Theta/Alert.

Removing of unserviceable stainless steel insulated hot water storage tank and supply and fixing new stainless steel insulated hot water storage tank duly fitted with heat exchanger suitable make and size for existing solar heater system of capacity 2500 LPD.

REPAIR TO FAN :- Taking down ceiling fan for repair/serviceing (i.e. winding/ greasing/oiling etc.), 1200 mm sweep of any make and any type model, sealing cable end with tape, dismantling the blades , removing fan and deposite the blades/motor to store for repairing/serviceing complete all as specefied and as directed by Engineer in charge.

Hanging only ceiling fan and connection up the point including provision of cable from ceiling rose to fan, replace old rusted d'clamp and flexible wire of size 23/0.0076 stranded copper conductor as per site requirement complete all as specefied and as directed by Engineer in charge.

Re-winding of ceiling fan of size 1200 mm sweep with super enameled copper winding wire of gauge as per existing size /No. of turns confirming to IS, including varnishing the motor windings with best quality varnish, replace of bearing/bush/ shaft complete all as specefied and as directed by Engineer in charge. (Make:Milan/Atlas/Chetak)

S&F condenser 2.5 MFD confirming to IS complete all as specefied and as directed by Engineer in charge.

REPAIR TO EXHAUST FAN Taking down and dismantling of exhaust fan 225mm of any make and model, opening the cover, separating the rotor and stator assembly, locating the burnt / fault and making the fan fully serviceable condition including rewinding of motor , replacing condencer 4 MFD , old borken blade, defected worn out screw, flexible wire of size 23/0.0076 , oiling/greasing the fan and re-assembling the same and testing complete to the satisfaction of Engineer in charge.

Taking down and dismantling of exhaust fan 300mm sweep of any make and model, opening the cover, separating the rotor and stator assembly, locating the burnt / fault and making the fan fully serviceable condition including rewinding of motor , replacing condencer 4 MFD , old borken blade, defected worn out screw, flexible wire of size 23/0.0076 , oiling/greasing the fan and re-assembling the same and testing complete to the satisfaction of Engineer in charge.

Taking down and dismantling of exhaust fan 375mm of any make and model, opening the cover, separating the rotor and stator assembly, locating the burnt / fault and making the fan fully serviceable condition including rewinding of motor , replacing condencer 4 MFD , old borken blade, defected worn out screw, flexible wire of size 23/0.0076 , oiling/greasing the fan and re-assembling the same and testing complete to the satisfaction of Engineer in charge.

Taking down and dismantling of exhaust fan 450mm sweep of any make and model, opening the cover, separating the rotor and stator assembly, locating the burnt / fault and making the fan fully serviceable condition including rewinding of motor , replacing condencer 4 MFD , old borken blade, defected worn out screw, flexible wire of size 23/0.0076 , oiling/greasing the fan and re-assembling the same and testing complete to the satisfaction of Engineer in charge.

Taking down carefully existing unserviceable Copper/aluminum batten/surface conduit/concealed conduit point wiring (light, fan, bell/buzzer, socket or power) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, pendents, sockets, lamp holders, shades, fan regulators, light fittings, bells etc (including old MS sunken boxes) and removing the retrieved materials from dismantling including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and as directed by the Engr-in-Charge.

M&L Point wiring with stranded copper conductor cable, 1100 volts grade (ISI marked) PVC insulated and unsheathed of size 1.5 Sq mm single core in PVC concealed/Cassing capping/ conduit Medium class 20mm dia ISI marked with all fittings such as tees, bends etc terminating in and including sunken box covered with and including 3 mm thick bakelite laminated sheet top cover ‘Hylam’ for one fan or light or 5Amps socket or exhaust fan or bell/buzzer point controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed copper conductor cable, single core as earth wire to common earth & connecting to earth dolly complete all as specified and directed by Engineer-in-Charge.Make of cables :Havell's/Paragon/Nicco/L&T.Make of PVC Conduit : Polycab/Supreme/Modi/Finolex/Prince/Precision

All as per item No 93 here-in-before but in existing conduit cable of 1.5 Sq mm complete all as specified and directed by Engr-In-charge.

All as per item No 93 here-in-before but socket point on the same board with other switches complete as specifed as directed by Engineer - In - Charge

All as per item No 93 here-in-before but socket point on the independent board with other switches complete as specifed as directed by Engineer - In - Charge

All as per item No 93 here-in-before but cable of 2.5 Sq mm for 15 Amp switch socket outlet on independent board including provision of 2.5 Sqmm PVC insulatred unshethed multistranded copper conductor as earth wire

All as per item No 93 here-in-before but in existing conduit cable of 2.5 Sq mm for 15 Amp switch socket outlet on independent board

All as per item No 93 here-in-before but in existing conduit cable of 4 Sq mm for 25 Amp switch socket outlet on independent board

All as per item No 93 here-in-before but one light point controlled by two 02 - way switch complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement LED T5 Batten lightening fixture, energy efficent 18/20 Watt ( 4 feet) complete all as specified and directed by engineer-in-charge make:-CG/ Havells/Phillips

S&F in replacement LED T5 Batten lightening fixture, energy efficent 9/10 Watt ( 2 feet) complete all as specified and directed by engineer-in-charge make:-CG/ Havells/Phillips

Supply & fix LED bulk head ,09W / 10 W, IP65 diacast aluminium housing powder coating finished > 0.9 complete all as specified and directed by Engineer-in-charge. Cat Part no. SSk-BH-9W in make Syska / havell's / Phillips.

S&F in replacement Recessed mounting LED 2x2 luminaire type BCTBLR 36W ZTN NW in make Bajaj or equivelent in CG / Phillips / GE / Wipro / Havell's

S&F LED 2x20W NW interconnectable luminaires for aesthetically appealing downlight application complete all as per specified and directed by Engr-in-Charge Cat Part No. 112114 in make Bajaj and or equivalent

S&F LED 2x40W NW interconnectable luminaires for aesthetically appealing downlight application complete all as per specified and directed by Engr-in-Charge Cat Part No. 112205 in make Bajaj and or equivalent

S&F Recessed mounting LED 4x1 luminaire type Cat Part No. 112665 in make : make Bajaj or equivelent in CG / Phillips / GE / Wipro / Havell's

S&F in replacement lamp holder PVC/Poly carbonate body with back plate complete all as specified and as directed by Engineer-in-Charge.Make - Havells. Cona, SSK, wipro, Legrand

S&F in replacement Modular switch 1 way 6A, 1 modul complete all as specified and as directed by Engineer-in-Charge Make - Havells. Cona, SSK, wipro, Legrand

S&F in replacement Modular switch 1 way 16A, 1 modul complete all as specified and as directed by Engineer-in-Charge Make - Havells. Cona, SSK, wipro, Legrand

S&F in replacement Socket, 6A - 2/3 pin combined 2 modul complete all as specified and as directed by Engineer-in-Charge Make - Havells. Cona, SSK, wipro, Legrand

S&F in replacement Socket, 16A - 2/3 pin combined 2 modul complete all as specified and as directed by Engineer-in-Charge Make - Havells. Cona, SSK, wipro, Legrand

S&F in replacement Fan step regulator, 120W - 2 module complete all as specified and as directed by Engineer-in-Charge Make - Havells. Cona, SSK, wipro, Legrand

S&F in replacement White cover plate with frame, 1 modul complete all as specified and as directed by Engineer-in-Charge Make - Havells. Cona, SSK, wipro, Legrand

S&F in replacement White cover plate with frame, 2 modul complete all as specified and as directed by Engineer-in-Charge Make - Havells. Cona, SSK, wipro, Legrand

S&F in replacement White cover plate with frame, 3 modul complete all as specified and as directed by Engineer-in-Charge Make - Havells. Cona, SSK, wipro, Legrand

S&F in replacement White cover plate with frame, 4 modul complete all as specified and as directed by Engineer-in-Charge Make - Havells. Cona, SSK, wipro, Legrand

S&F in replacement White cover plate with frame, 6 modul complete all as specified and as directed by Engineer-in-Charge Make - Havells. Cona, SSK, wipro, Legrand

S&F in replacement White cover plate with frame, 8 modul complete all as specified and as directed by Engineer-in-Charge Make - Havells. Cona, SSK, wipro, Legrand

S&F Socket outlet 2 in 1, 3 pin, 5A ISI marked, complete all as specified and as directed by Engineer-in-Charge

S&F Switch piano flush type, Single pole 5 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge

S&F switch socket combination 5 in 1, 5/16 amp flush type fixed on laminated sheet top cover complete all as specified and as directed by Engineer-in-Charge

S&F Bell push flush type, 5 Amps, ISI marked, complete all as specified and as directed by Engineer-in-Charge

S&F Bell Buzzer, Ding Dong AC 230 Volts, single pole ISI marked, complete all as specified and as directed by Engineer-in-Charge

Supply and fixing in replacement of PVC connector, ISI marked complete all as specified and as directed by Engineer-in-Charge

Supply and fixing in replacement of Tv socket flush type, ISI marked complete all as specified and as directed by Engineer-in-Charge

Supply and fixing in replacement of Telephone socket flush type, ISI marked complete all as specified and as directed by Engineer-in-Charge

Supply and Fixing MCB single pole, 240 volts of rating 6-32 Amps of C curve breaking capacity of 10 KA complete all as specified and as directed by Engineer-in-Charge Make :- Legrand,ABB,Schneider

Supply and Fixing MCB suitable for 6 to 32 Amps, 240 Volt AC supply C Curve single pole and neutral(SPN) with over load and short circuit protection having rupturing capacity not less than 10 KA complete all as specified and as directed by Engineer-in-Charge. Make :- ABB,Legrand,Schneider

Supply and Fixing in replacement MCB 63 Amps, 440 Volt AC supply Triple pole with neutral(TPN) C curve with over load and short circuit protection having rupturing capacity not less than 10 KA complete all as specified and as directed by Engineer-in-Charge. Make :- Legrand/ABB/Schneider

Supply and Fixing in replacement MCCB 3 Pole, 415 V, fixed type, 25 to 100 Amps with breaking capacity 16 K complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing in replacement MCCB 4 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 36 K complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement Sheet metal enclosure for distribution boards flushed in wall Double door suitable for fixing MCBs 240 volts with 200 Amps rated bus bar,SPN 8 ways, including taking down of old unsv DB,s and making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge. Make -L&T ( Exora series)/Schneider/ legrand/Schnedier/GE /English Elect Note : cost of cutting/chasing of wall and making good disturbed surface deemed to be included in the rate

S&F in replacement Sheet metal enclosure for distribution boards flushed in wall Double door suitable for fixing MCBs 240 volts with 200 Amps rated bus bar,SPN 12 ways, including taking down of old unsv DB,s and making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge. Make -L&T ( Exora series)/Schneider/ legrand/Schnedier/GE /English Elect Note : cost of cutting/chasing of wall and making good disturbed surface deemed to be included in the rate

S&F in replacement Sheet metal enclosure for distribution boards flushed in wall Double door suitable for fixing MCBs 240 volts with 200 Amps rated bus bar,TPN 4 ways, including taking down of old unsv DB,s and making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge. Make -L&T ( Exora series)/Schneider/ legrand/Schnedier/GE /English Elect Note : cost of cutting/chasing of wall and making good disturbed surface deemed to be included in the rate

S&F in replacement single pole and neutral enclosure with two pin and earth plug and socket including 1Nos MCB 06 to 32 Amps capacity complete all as specified and directed by Engr-in-charge Cat Part No 607841 in Make Legrand or equivalent in schneider/Seimens/L&T

Taking down of old u/s sub main wiring any size complete all as per specified and directed by Engr-in-charge.

Sub main wiring in PVC concealed conduit with 2 single core 10 sqmm multi-stranded PVC insulated cable unsheathed 1100 volts grade with one earth wire of 6 sqmm copper conductor cable connected to common earth and earth dolly complete and including PVC Cassing and Capping all as specified and as directed by Engineer-in-Charge.(Note two run of 10 sqmm and one run of 6 sqmm will be measured as 1 RM.Make of cables: Nicco, L&T, Paragon, havells

Sub main wiring in PVC concealed conduit with 2 single core 04 sqmm multi-stranded PVC insulated cable unsheathed 1100 volts grade with one earth wire of 2.5 sqmm copper conductor cable connected to common earth and earth dolly complete and including PVC Cassing and Capping all as specified and as directed by Engineer-in-Charge.(Note two run of 4 sqmm and one run of 2.5 sqmm will be measured as 1 RM.Make of cables: Nicco, L&T, Paragon, havells

Sub main wiring in Existing PVC concealed conduit with 2 single core 4 sqmm multi-stranded PVC insulated cable unsheathed 1100 volts grade with one earth wire of 2.5 sqmm copper conductor cable connected to common earth and earth dolly complete all as specified and as directed by Engineer-in-Charge.(Note two run of 4 sqmm and one run of 2.5 sqmm will be measured as 1 RM.Make of cables: Nicco, L&T, Paragon, havells

Sub main wiring in Existing PVC Surface conduit with 2 single core 10 sqmm multi-stranded PVC insulated cable unsheathed 1100 volts grade with one earth wire of 6 sqmm copper conductor cable connected to common earth and earth dolly complete all as specified and as directed by Engineer-in-Charge.(Note two run of 10 sqmm and one run of 6 sqmm will be measured as 1 RM.Make of cables: Nicco, L&T, Paragon, havells

Sub main wiring in Existing PVC Concealed conduit with 4 single core 25 sqmm multi-stranded PVC insulated cable unsheathed 1100 volts grade with two earth wire of 16 sqmm copper conductor cable connected to common earth and earth dolly complete all as specified and as directed by Engineer-in-Charge.(Note four run of 25 sqmm and two run of 16 sqmm will be measured as 1 RM.Make of cables: Nicco, L&T, Paragon, havells

Sub main wiring in Existing PVC Concealed conduit with 4 single core 16 sqmm multi-stranded PVC insulated cable unsheathed 1100 volts grade with two earth wire of 10 sqmm copper conductor cable connected to common earth and earth dolly complete all as specified and as directed by Engineer-in-Charge.(Note four run of 16 sqmm and two run of 10 sqmm will be measured as 1 RM.Make of cables: Nicco, L&T, Paragon, havells

Sub main wiring in Existing PVC Concealed conduit with 4 single core 10 sqmm multi-stranded PVC insulated cable unsheathed 1100 volts grade with two earth wire of 6 sqmm copper conductor cable connected to common earth and earth dolly complete all as specified and as directed by Engineer-in-Charge.(Note four run of 10 sqmm and two run of 6 sqmm will be measured as 1 RM.Make of cables: Nicco, L&T, Paragon, havells

Sub main wiring in Existing PVC Concealed conduit with 4 single core 6 sqmm multi-stranded PVC insulated cable unsheathed 1100 volts grade with two earth wire of 4 sqmm copper conductor cable connected to common earth and earth dolly complete all as specified and as directed by Engineer-in-Charge.(Note four run of 6 sqmm and two run of 4 sqmm will be measured as 1 RM.Make of cables: Nicco, L&T, Paragon, havells

JAGDAMBA CONSTRUCTION COMPANY

ENGINEER CORPORATION OF INDIA