Special repair to four water storage tanks two overhead tanks and Provn of vertical and horizontal rope urinal points with water connection at Mil Stn Jaisalmer

Amount

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in hard/ dense soil.

Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete.

M &L Squared rubble walling Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in CM 1:6

Extra over for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm and dressing face beds and joints as specified to squared rubble walling, Jodhpur type, brought upto courses.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils.

Removing Excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point.

Rendering 15 mm thick on stone masonary in cement mortar 1:6 and finished even and smooth without using extra cement.

M&L for applying two coat of oil bound distemper with two coat of putty on wall incl. preparation of new surface complete all as specified and directed.

M & L PCC 1:3:6 type C-2 using 40 mm graded aggregate as in sub base 75 mm thick

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in floors & finished the surface even & fair without using extra cement all as specified.

M&L for Non Skid ceramic tiles colour jointless tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified.

M&L for Glazed ceramic tiles dark shade in vertical surface 450X300X7mm thick,jointless tile set and jointed in neat cement slurry and pointed in white or coloured cement, set in 10mm thick backing coat in CM 1:4

S&F 15mm GI tubing (ISI) marked) medium grade with all fitting and fixed complete to wall ceiling or laid in floors

S&F 20mm GI tubing (ISI) marked) medium grade with all fitting and fixed complete to wall ceiling or laid in floors

125mm butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed, type-II

S&F 150mm fancy type brass handle, cast type.

S&F, 700mm x 500 mm x 5mm thick glass mirror with double coat for protection and longevity grounded edges for safety and Silver plating on the back for better reflection complete all as specified & directed by Engineer-in-charge. (Make : Cera Cat Part No. B3510112, Prayag, Jaquar). .

S&F 32mm dia High density polyethylene pipe (HDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc.

M&L for 75 mm dia Cast iron nahani trap, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4)

M&L for 100 mm dia Cast iron nahani trap, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4)

S & F Vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm size including cutting for and pinning ends of brackets or erecting stand.

S&F pillar taps 15 mm bore cast copper alloy with capstan head chromium plated screwed down high pressure with or without 'Hot' & 'Cold' with long screwed shanks and fly nuts, screwed complete.(Prayag Cat Part No.- 8304, Cera Cat Part no. -F 2006101, Hindware Cat Part No. -F 33002,Silver shine model no:-1065)

S&F vitreous china white wash down water closet pan, pedestal pattern including fixing bolts, plastic water closet seat and cover with recessed bottom with MS CP hinging device (excluding flushing cistern and flush pipe) complete all as all as directed by Engr-in-Charge.

S&F in repairs PVC connection pipe 15mm dia, 600mm long with PTMT check nuts and washer on both ends complete all as directed by Engr-in-Charge.

M&L for 25mm thick granite counter for wash basin (Tabled rubbed and polished) supported on walls in cement mortar (1:4) including pointing in white cement 1:2, using marble dust with admixture of pigment to match the shade of granite stone including cutting and polishing.

M&L for precast cement concrete building block masonry type B1 1:2:4 (20mm gradded stone aggregate) in CM 1:4 in partition wall all as specified and directed.

S&F of Grating doom 100mm dia of PTMT (Minimum weight 25Gms)

S&F 75mm dia Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints laid in trenches or in floors

S&F 75mm dia Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints laid in trenches or in wall.

S&F 100mm dia Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints laid in trenches or in floors

S&F 75mm dia cast iron bends (any radius) dininishing pieces or tapers

S&F 100 mm dia cast iron bends (any radius) dininishing pieces or tapers

S&F cast iron 75mm floor trap.

S&F cast iron 100mm floor trap.

S&F cast iron 75mm dia oval access door

S&F cast iron 100mm dia oval access door

S&F bib taps 15 mm dia of cast, copper alloy with crutch or butter fly handle screwed down screwed for brass ferrule or iron pipe and fixed in repairs.(Prayag Cat Part No.- 8306, Cera Cat Part no. -F 2006151, Hindware Cat Part No. -F 330003, Silver shine model no:-1001)

Preparing new plastered or un plastered surfaces and applying two coats of cement base paint on surfaces of walls.

S&F stop cock 15 mm dia fancy type cast copper aloy with crutch handle CP facy type long shank fixed in repairs

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied & fixed in opening as per specification & drawing.

S&F factory made solid panneled PVC door shutter 30mm thick (style) consisting of frame out of MS tubes for top and bottom rails MS frame shall be covered with sheet moulded plain coloured PVC 'C' channel having a PVC sheets of 20mm width stuck inside with solvent cement for site and frame coloured PVC sheets for top rails as gap insert for top rails on either side and as gap insert for top rails and bottom rails pannelling of plain coloured PVC sheets to be fitted in the MS frame welded sealed to the site and rails with suitable PVC sheets beading and joints together with solvent cement in the frame at site as per specification. (PVC door shutter) complete all as directed.

Applying bituminous primer on roof surfaces @ 0.40 ltr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and laying polymeric water proofing membrane 3 Kg/Sqm and bonded completely to the surfaces with overlap of 10 cms (overlaps to be thermo fused by flame) and applying one coat of hot blown bitumen 85/25 @ 0.70 Kg/Sqm all as directed. Make: STP/IWL

M&L for 40 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate in Padding all as specified .

M&L for 100 mm thick cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate water tank floor area all as specified & directed.

M&L for Jodhpur stone roof slabs, self faced, 7.5cm to 10 cm thick, 25 cm to 35 cm wide, hoisted & set, jointed and grouted in cement mortar (1:3) all as specified.

M&L for rendering 15 mm thick on stone masonry surface in cement mortar 1:4 mixed with water proofing compound at the rate of 3% by weight of cement and finished even & smooth without using extra cement (Supply only water proofing compound shall be measured and paid separately).

M&L for sand stone slabs as in shelves, sun sades chajja of 50mm thick set in CM (1:4) n. exc 2m in length all as specified.

S&F Vitreous china urinals with urinal spreader, full stall (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing (Cera Cat Part No- 54020102,Hindware Cat Part No-60002)

Excavating in trenches n.exc 1.50m deep and getting out in soft/disintegrated rock for foundations, manholes etc complete all as directed by Engineer-in-Charge.

All as per Sl item No.1 above, but depth exc 1.50m but n.exc 3.00m complete all as directed by Engineer-in-Charge.

Pre-cast cement concrete block masonry Type C1 1:3:6 (20 mm graded aggregate) Set in cement mortar 1:4 with solid blocks, exc. 10 cm in width and setting in mortar, complete

M & L for Mild steel deformed TMT bars 8mm dia and over cut to length, bent to shape required including cranking, bending and binding with mild steel wire (annealed) not less than 0.9 mm dia all as directed by Engineer-in-Charge.

M & L for pre-cast cement concrete (1:2:4) type B1 using 20mm graded stone aggregate) in cover slabs including necessary from work etc., complete all as specified and as directed by Engineer-in-Charge.

Removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as directed by Engineer-in-Charge.

Returning, filling in, with soil obtained from excavation including spreading, leveling, watering and well ramming in layers not exceeding 25cm complete all as directed by Engineer-in-Charge.

S&F RCC pipe class NP-2 ISI marked laid to slope in trenches jointed and tested complete with collars for 150 mm dia pipe all as specified.

Surface excavation n.exc. 30 cm deep and averaging 15cm deep and getting out in soil

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm

M & L for plastering in CM 1:4 , 15 mm thick complete all as specified and directed

M&L PCC 1:3:6 type C 1 using 20 mm graded stone aggregate in coping and the like including weathering slightly rounded/ chamfered angles with & including necessary use and waste of form work for fair faces of concrete, complete.

M&L for spreading of loose layer of sand all as specified and directed by Engr in Charge.

S&F framed work, trussed, purlins, rafters, rails, colmns and fastenings and heavy bracket framing (pipes , beam, tee, angle, channel, hallow sections) including distance pieces, cleats, hook clips etc

M&L Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for two coats of synthetic enameled paint over a coat of red oxide including prepration of newly surfaces of any description over 10cm in width or girth all as specified

S&F Rope jut 40 to 50mm dia all fixing arrangment including binding top end and fixing in any height to hook as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified & directed by Engineer-in-charge.

Demolition of cement concrete unreinforced in ground floors, kota stone, granite flooring, tiles flooring and pavings not exceeding 15cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m all as specified & directed.

M&L for rendering 10 mm thick on on brick work or concrete surface in cement mortar 1:3 in one layers and mixed with integra water proofing compound at the rate of 3% by weight of cement and finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge. (Note :- Integral water proofing compound will be measured & paid seperately as supply only).

Supply only integral water proofing compound all as specified & directed by Engineer-in-charge.

M & L for Rendering 15mm thick (1:4) on fair faces of brick work or concrete surfaces, wall and any type of projection like facia, chajja etc or as specified. Finished even & smooth without using extra cement .

M&L for providing aliphatic acrylate based anti carbonation protective coating system for concrete/masonry surfaces comprising of the following : - (a) Preparation of surfaces including complete removal of existing treatment and dusting to receive new treatment. (b) Applying one coat of Silane/Silaxone blend primer @ 0.125 ltr/Sqm or covering 8.0 Sqm/Ltr using portable spray equipment of the knapsack type. (c) Applying polymer under coat over completely dired primer surface using brush or roller to achieve a uniform coating with wet film thickness of not less than 250 microns (coverage not more than 2.5 Sqm/ltr). (d) Applying aliphatic acrylate pigmented top coat (Shade as approved by GE) to a uniform wet film thickness of not less than 125 microns (coverage not more than 8.00 Sqm/ltr).

ITEM NO. 71.00 CONTD... Make :-Dekguard S300 Chemcal/Chemo System. (Primer, Coat & Top Coat shall be of same brand. Note- (a) The treatment shall be applied by the company authorised applicator only (b) Rate of item shall be inclusive of material, labour, tools and tackle, scaffolding etc complete as per specification and as directed by GE

Plinth protection 75 mm thick cement concrete 1:3:6 Type C2 ( 1 cement : 3 coarse sand : 6 - 20 mm size aggregate ) over 75 mm thick bed of dry brick bats/stone boulder ( 40 mm nominal size ) well rammed and consolidated with sand including finishing of top surface .

M & L for hardcore of gauge not exceeding 63 mm of broken granite stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface.

M&L for 75 mm thick cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base of flooring / hardstanding.

M&L for 25mm thick sand cushing for laying of precast concrete interlocking tiles including watering and consolidation complete.

M & L for 60mm thick inter locking cement concrete mixed colour factory made paver blocks M-35 designation (compressive strength) laid over 25 mm thick sand cushion to maintain the slope including compaction with 75 mm thick cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base etc.

M &L for Providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges as directed ny Engr-in-Charge

M&L for mild steel TMT bars 10mm dia & over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed by Engineer-in-Charge.

Hard drawn steel wire fabric n.exc 4.00 kg cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt

Bonding the entire exposed surface with one coat of fosroc Nitop bond SBR as per manufacturer instructions’ over whire fabric and surfaces of concrete structure complete after applying one coat of rust remover on steel reinforcement all as specified and as directed.

M/S JAGDAMBA ENTERPRISES