Loading…
Loading…
| # | Company | Status |
|---|---|---|
| 1 | Admitted-Finance | Admitted-Finance |
| 2 | Admitted-Finance | Admitted-Finance |
| 3 | Rejected-Technical B 104 MANISHA TOWER PLOT 7B SECTOR 23 DWARKA NEW DELHI 110 077 | Rejected-Technical NON RESPONSIVE |
| 4 | Not Admitted-Fee/PreQual/Technical BADRI RAI COMPANY ARUN KUMAR RAI DULIAJAN STATION ROAD P O DULIAJAN P S DULIAJAN DIBRUGARH PIN 786602 | DULIAJAN | DIBRUGARH | ASSAM | 786602 | Not Admitted-Fee/PreQual/Technical Not Complied with technical specification |
| 5 | Rejected-Technical 614 HARIOM TOWER COMMERCIAL COMPLEX CIRCULAR ROAD LALPUR RANCHI JHARKHAND 834001 | RANCHI | JHARKHAND | 834001 | Rejected-Technical NON RESPONSIVE |
Tender Value
Refer Docs
EMD Value
₹2.0 Cr
Closing Date
24 Aug 2022, 5:00 pmClosed
Nodal Officer
e Procurement Cell,BCD,Jharkhand,Ranchi
Proposed Residential Complex for Honourable MLAS in Core Capital Area at Site-1 HEC Area Ranchi
2022_BCD_60519_1
BCD/ Special Works Division,Ranchi/08/2022-23
Open Tender
Civil Works - Buildings
730 days
Ranchi
Please refer Tender documents.
2 documents required · 2 mandatory
₹10,000
EE,BCD,Special Works Division Ranchi
₹2.0 Cr
Building Construction Department
8 Sept 2022
4 Aug 2022
26 Aug 2022
4 Aug 2022
24 Aug 2022
4 Aug 2022
10 Aug 2022
Amount
Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a disposal of excavated earth as obtained to a distance upto 50m. Including all lifts, levelling, ramming the foundation tenches removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/I
Extra for earthwork in hard soil as per specification and direction of E/I
Filling in foundation trenches and plinth in layers not exceecJing .i50 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 m all complete as per building specification and direction of E/l (Mode of measurement compacted volume).
Providing coarse clean sand in filling in foundation trenches or in plinth (upto ground floor level) including ramming and watering in layers and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour,royalty and taxes all complete as per building specification and direction of E/I(Mode of measurement compacted volume).
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level 1:3:6 ( 1 Cement : 3 Coarse Sand : 6 graded stone agreegate 20 mm nominal size )
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level 1:2:4 ( 1 Cement : 3 Coarse Sand : 6 graded stone agreegate 20 mm nominal size )
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.
All Works upto plinth
All works above plinth level upto floor V level
Extra for concrete work in superstructure above floor V level for-each-four-floors or part thereof.
Providing & Laying Centering and shuttering including strutting, propping etc. and removal for all height:
Foundations, footings, bases of columns, etc. for mass concrete
Walls (any thickness) including attached pilasters, butteresses,plinth and string courses etc.
Edges of slabs and breaks in floors and walls Under 20 cm wide
Weather shade, Chajjas, corbels etc., including edges
Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick.
Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick
Columns, Pillars, Piers, Abutments, Posts and Struts :
Stairs, (excluding landings) except spiral-staircases
Cornices and mouldings
Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)
STEEL REINFORCEMENT:- Providing Tor steel reinforcement of any diameter bars as below as per approved design and drawing including carriage of bar, cutting,bending,and binding with annealed wire with cost of wire ,removal of rust,placing the rods in position all complete as per building specification and direction of E / I.
Providing Tor steel reinforcement of 8mm. dia rods as per approved -do- TMT Fe 500 {Only valid for Tata (Tlscon), SAIL, JSPL,Electrosteel Steels Ltd, Bokaro and Vizag (RINL)}
Providing Tor steel reinforcement of lOmm.,12mm & 16 mm. dia bars as per approved design and drawing -do- -do- (a) 10 mm (TMT coil Fe 500) {Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}
Providing Tor steel reinforcement of 12mm & above dia rods as per approved design and drawing -do- -do- TMT Fe 500 (Only valid for SAIL & TATA Steel, JSPL, and Vizag Steel)
Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete :
Serrated with central bulb (225 mm wide, 8-11 mm thick)
Dumb bell with central bulb (180 mm wide, 8 mm thick)
Kickers (320 mm wide, 5 mm thick)
Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).
Providing designation 75 A brick work in C.M. ( 1 : 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.
Providing designation 75 A brick work in C.M. ( 1 : 6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, scaffolding ,raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.
Extra for brick work for each consecutive floor above first floor including watering and scaffolding, all complete as per direction of E/I
Providing designation 125 mm thick reinforced designation 75A brick work in C.M. ( 1:4 ) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials, scaffolding, raking out joints to 15 mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.
Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.
AAC BLOCK:-Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.
AAC BLOCK:-Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).
Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in door, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/I.
Supplying, fitting and fixing good quality, well dressed and well seasoned teak wood work in chaukhat in door, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/I.
Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I) On one side only
Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).
Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :2nd class teak wood 50 x 20 mm
P/L French spirit polishing :Two or more coats on new works including a coat of wood filler
Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:-Butt hinges and necessary screws shall be paid separately)Second class teak wood35 mm thick shutters
Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :
Second class teak wood
5.0 mm thick glass panes (weight not less than 12.5 kg per sqm)
Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.
Providing and fixing to existing door frames 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/ Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free,straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :
Note 1:- Scope of supply includes Design, Fabrication, Supply Installation, Testing, Projection, Cleaning & Handover of respective façade system mention below,custom designed to with stand the design wind pressure confirming to IS-875 part III.The design of aluminium members to comply IS 8147-1976. The system must pass the proof test at 1.5times design wind pressure i.e. 170kg/sqm without any failure.The quote rate shall include all design, engineering drawing, fittings & fixture, Lead & Lift, all taxes,duties,statutory obligations and safety code compliance as per PMC. All material Make as per approved material List. All shade approval shall be as per architect/consultant. No procurement/work to commence on site prior to shop drawing approval from architect/consultant.
NOTE 2:-Aluminium work Like Structural Glazing, Aluminium window & Louver , Facade of Toilet Block, work should be executed by specialized agency . The contractor shall submit 5 copies of shop drawings for Structural glazing, Aluminium Door & Window, Composite Window, Louver showing dimension details of construction etc. for approval and according to the approved shop drawing a sample of each of system with all fittings and fixture with locking arrangement including glass panes submitted for preliminary inspection for sample approval. After that the sample should be fixed at site to ascertain its performance. Large scale manufacturing should be taken up only after rectification of defects in sample as directed to the full satisfaction of the department / PMC and after obtaining formal approval of the same.
For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)
For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)
Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width
Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
Providing and fixing fan hook of 16 mm dia M.S. bar 1 metre long bent to required size and shape,placed in position and fixed in R.C.0 slab/beam at the time of casting all complete as per building specification and direction of E/I. (where material is not supplied by deppt.)
Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.
In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete
In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the Same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover
Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer-in- charge, (area of grill to be measured).
Providing and fixing ball bearing for rolling shutters.
Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 16.80 sqm in area
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate with all lead & lift.
Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement 18 mm thick. (With all lead & lift)
62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.
KOTA FLOORING:-Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick
Kota stone slabs 20 mm thick in skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.
Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.
Size- 300mmx450mm
Size- 300mmx200mm
Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 1200 mm
Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade
Area of slab upto 0.50 sqm
Area of slab over 0.50 sqm
Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete
Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with :Second class deodar wood
Providing & Fixing decorative high pressure laminated sheet of plain /wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.1.5 mm thick
Providing 6mm. cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.
Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface inluding preparing the plastered surface by rubbing wmooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specifica tionand direction of E/I.
Wall Plastering work:-Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.
Providing 19mm. thick water proof cement plaster (1:3) with clean coarse sand of F,M 1.5 with 5% cico or any other approved water proofing compound including. -do-
Extra for plaster work over exterior surface for each consecutive floor above first floor including cost of scaffolding etc. all complete as per direction of E/I
Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm
Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer
Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :Two or more coats on new work
Providing priming one coat of approved shade and make over new wooden surface after cleaning removing dirt, scales smoke, grease ands sand papering including cost of scaffolding and taxes all complete as per building specication and direction E/I
Providing two coats of synthetic enamel paint of approved shade and make over new wooden surface after cleaning removing dirt, scales smoke, grease ands sand papering including cost of scaffolding and taxes all complete as per building specication and direction E/I
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work
NOTE FOR WATER PROOFING WORK:- a) The contractor shall get written approval from the Engineer- in- charge, for water proofing work , Special agency from manufacturer recommendation was engaged their sound applicator and shall submit detail procedure of application alongwith specification.
b) The contractor shall furnish guarantee bond on appropriate stamp paper for the entire waterproofing treatment for maintaining the surroundings and under side surfaces of the waterproofing treated area in bone dry condition for 10 years. During the guarantee period the contractor shall attend and rectified all leakages, defects etc. if noticed, free of cost, within a day's time from the date of intimation about such leakages/defects.
c) The contractor shall test the surface where water proofing treatment provided for bone dry condition by filling up with water. No wet patches or leaks shall appear on the surrounding wall or under side of the slab.
d) The Contractor shall keep the water proof area filled with water after the water proofing work has been completed for testing of leakage and shall clean it before handing over. Faulty area shall again be done, before handing over the , if found necessary by the Engineer- in-charge.
Waterproofing of Roof or Open terrace
Water proofing for Old and New Roof Slab Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible material applied with brush, roller or spray for water proofing coating as per manufacturer specifications with following steps
(a) Surface preparation :-Providing and cleaning of concrete surface to remove dust, oil, grease including removal of existing loose paint / coating, and cement laitance by Cleaning with compressed air & water jet including all materials, labour, tools complete.' Ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage,leakage. On identification of seepage cement grouting be done with non shrink expanding admixture of Slka Indi Pvt Ltd/MYK Schomberg/ Dr Fixit/Fosroc or eqüivallente.Provtding and reparing of all corners and joints such as those between thr parapet wall and the roof slab etc. shall be chamfered with 150mm X 50 mm fillet of mortar (Cement: sand 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent. Before chamfering a prime coat shall be given with the slurry of acrylic polymer . Repairing surface irregularities, damaged concretein base slab dead cracks if any, with an acrylic polymer modified repair mortar inc!uding a coat of bonding agent of the same with cement slurry including all material, labour, tools complete.
(b) 1st Coat :-Apply 1St coat of two component acrylic modified, ready to use, flexible cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roller. After 1st coat of application 45 gsm of Fibre glass cloth to lay when the first layer is still green. 1st coat shduld be applied @1.50 kg/Sqrni/coa!. For the purpose of measurement the entire treated surface will be measured.
(c) 2nd Coat:-TO apply the 2nd coat of two component acrylic modified, ready to use, flexible cementitious material right angle to the Ist coat over the glass fibre laid surface. 2nd coat should be [email protected]/Sqmt/coat. For the purpose of entire treated surface will be measured." After three days of drying the 2nd coat , the rain water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification to be done as per satisfaction of E/C. The waterproof coating to be protected from damage before screed over it. Waterproofing Brand:-Sika -Topseal 109hi / Fosroc Brushbond RFX/Dr Fixit Pidiffin 2K / MYK Aquafin TG. Product Performance. Chemical Base Part A: Acrylic copolymeri Part B: Specially graded cementitious powder - Density 1.6 kg/l (mixed density) at + 27 degree C Tensile Strength — 2 N/mm2 after 28 days (with Fibre cloth) (According to ASTM D 2370) Pullout Bond Stren th —2 N/mm2 concrete failure Accordin to ISO 4624) Slant . Shear Bond Strength-4N/Sqmm(According to FIP 5.15). Elongation at break-35% without Fibre Cloth and 20% with Fibre Cloth (According to ASTM D 2370).
(d) Protection of treated surface With PCC :-The treated surface should be covered with 25mm/50mm PCC of M-20 grade(1.1.5 3) with proper slope ( 1:120) towards the rain outlets in alternate panels of 2 mt x 2mt keeping 6 mm gap between the panel Joint. Integral water proofing admixture conforming to IS 2645 @ of 100 ml per bag of cement to be added in the screed concrete (paid separately for this items) All corners shall be chamfered with 150mm X 150 mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water , the peripheral gaps between pVG pipe outlet and concrete surface should be packed properly with rich concrete and the peripheral mouth to be sealed with moisture insensitive epoxy putty of Sika Pvt. Ltd. / MYK Schomberg / Dr Fixit/Fosroc. For the purpose of measurement the entire treated surface will be measured,"
Covering of treated surface with PCC :- Providing 50 mm thick Cement Concrete mantaining a slope in alternate 2 mt 2 panels with approved quality of stone chips of 20mm to 6mm size graded and cleaned sand of F. M. 2.5 to 3 including screening,shuttering,and mixing cement concrete in mixer with admixture of integral water proofing and placing in positjon,striking curing,taxex and royality all complete as per building specfiction and directions of E/I . Panels that has been left shou!d be casted next day.There should be 6 mm gap between Panels . Brand-Sika-P1astocrate plus, MYK proof WP 10,Fosroc-Conplast X 4211C, Dr-fixit Pidiproof LW+ or Equivalent .
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :
100 mm dia. R.C.C. Pipe
250 mm dia. R.C.C. Pipe.
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/I
Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade
Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)
Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used. With G.I. barbed wire
Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.
Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on interlocking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile, rotary stitched double webbed white with 6 mm reveal profile (white/black),comprising of main-T runners of size 15x42 mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross-T of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles.
Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :
12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)
Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in?charge.
With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7)
Providing and fixing 2nd class teak wood plain lining tongued and grooved, including wooden plugs complete with necessary screws and priming coat on unexposed surface.25 mm thick
Stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand),including pointing in white cement with an admixture of pigment to match the stone shade.8mm thick (mirror polished and machine cut edge).Granite stone of any colour and shade
Supplying, fitting and fixing 40mm high vitreous white glazed earthen E.W.C. with ‘p’ trap of parry hindustan or any other approved I.S.S. make including supplying and fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I.handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450grams 15mm P.V.C. alkathene pipe 45cm. long with brass coupling at both ends and white/black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide priming, all complete as per specification and direction of E/I.
(i) With 'P' trap (b) 12.5 lit. low level PVC Cistem
(ii) With 'S' trap (b) 12.5 lit. low level PVC Cistem
Supplying, fitting and fixing flat back or angular, lipped front vitreous white glazed earthen ware urinal of ‘Hindustan "Parry" or any other approved I.S.S make with 5 liters capacity C.I. automatic fulsing cistern of reliance for any other I.S.S. approved make with all fittings with C.I.or R.S. brackets, standard size G.I. flush pipe with fitting clamps,15mm C.I. body brass spindle stop cock of approved quality weight not less than 400grams, 15mm P.V.C./ Alkthene pipe 450mm longwith brass coupling at both ends and doing plumber joints including painting of exposed part with two coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/I. (a) Flat back or standing corner (600mmx350mm)
Supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. approved make supported on painted C.I. or R.S. brackets 32mm C.I.brass waste, 15 mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.
Supplying fitting and fixing white glazed fire’s clay sink of approved make with overflow arrangements supported on C.I. or R.S. painted brackets 40mm. dia C.P.brass waste with C.P.brass chain and rubber plug 40 mm dia P.V.C. waste pipe about 750mm long with brass coupling at one endand 15mm C.I. body brass spindle bib cock of approved quality of weight not less than 450grams. including cutting wall and making good the same etc. all complete as per specification and direction of E/I. (i) Kitchen sink 600 mm x 450 mm x 250 mm
Supplying, fittings and fixing HCI pipes with ear of approved make confirming to ISI 1729 including supplying nails and bobins short pieces cutting loose collars lead and yarn for making lead caulked joints, cuttin pipes to size including earth work or scafolding where necessary etc. all complete as per specification and direction of E/I. a) 100 mm dia
Supplying, fittings and fixing HCI fittings of approved make confirming to ISI 1729 including supplying nails and bobins short pieces cutting loose collars lead and yarn for making lead caulked joints, cuttin pipes to size including earth work or scafolding where necessary etc. all complete as per specification and direction of E/I.
A) HCI single junction with door but without ear except socket i) 100 mm dia (wt. 10.5 kg. app)
B) HCI heal rest bend i) 100 mm dia (wt. 5.5 kg. app)
C) 100 mm dia HCI "P" trap with Anti Syphonage Horn (wt. 8.5 kg. app)
D) HCI double junction with door and ear i) 100 mm dia (wt. 15.5 kg. app)
G) HCI Bend with door and ear i) 100 mm dia (wt. 6.5 kg. app)
H) HCI plain bend with ear i) 100 mm dia (wt. 6.5 kg. app)
I) HCI shoe with ear i) 100 mm dia (wt. 5 kg. app)
Making holes in wall for laying HCI pipes and restoing the same after pipe laying as per specification and directed of E/I
125mm dia
250 mm dia
Supplying materials and labour for painting the exposed HCI pipes and fittings 2 coats of approved paint over a coat red oxide prime etc. all complete as per specification and direction of E/I. c) 100 mm dia
Providing and fixing male ended 15mm dia brass bib cock of approved make (wt. not less than 350grms.) with extra socket all complete as per specification and direction of E/I
Providing and fixing brass or C.I. stop cock of approved quality all complete as per specification and direction of E.I. A) BRASS STOP COCK 15mm dia
Providing and fixing lead connection pipe with heavy quality brass coupling 2 nos. at both ends etc. all complete as per specification and direction of Engineer-in-Charge. (ii) 15 mm dia and 45 cm long
Providing and fixing 15 mm. dia and 45cm. long P.V.C. connection pipe with heavy quality brass coupling at both ends etc. all complete as per specification and direction of Engineer-in-Charge.
Providing and fixing N.P/C.P. brass /P.V.C. porcelain shower rose of 15mm inlet etc. all complete as per specification and direction of Engineer - in - Charge. (b) 125mm dia C.P. shower
Providing and fixing 15mm size C.P. brass pillar cock (Weight not less than 350gms). C.I.body brass spindle pillar cock of approved quality as per specification and direction of Engineer-in-Charge. (b) C.I. body brass spindle
Providing and fixing Gun metal full way valve of approved quality, all complete, as per specification and direction of E/I.
(b) 20mm dia and weight not less than 400gms.
(c) 25mm dia and weight not less than 500gms
(d) 32mm dia and weight not less than 700gms
(e) 40mm dia and weight not less than 1.0 Kg..
(f) 50mm dia and weight not less than 1.5 Kg.
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the wall etc.
15 mm nominal outer dia Pipes
20 mm nominal outer dia Pipes
25 mm nominal outer dia Pipes
32 mm nominal outer dia Pipes
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work
20 mm nominal outer dia Pipes
25 mm nominal outer dia Pipes
32 mm nominal outer dia Pipes
40 mm nominal outer dia Pipes
50 mm nominal outer dia Pipes
Providing and fixing C.P. brass angle valve of approved quality conforming to IS:8931 a) 15 mm nominal bore
Providing and fixing 600 X 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with CP brass screws and washers complete .
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter
Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.
Coupler 110 mm
Single pushfit Coupler 110 mm
Single tee with door 110x110x110 mm
Single tee without door 110x110x110 mm
Bend 87.5° 110 mm bend
Shoe (Plain) 110 mm Shoe
Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank
Supplying materials and labour for constructing inspection chamber of designation class 75B bricks size 750mm deep 600x450mm internal dimension having 250mm wall thickness in cement morter (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600 x 475mm G.I. cover with frame (weight not less than 36kg) alongwith earth work in excavation and 80min thick PCC (1:3:6) in foundation and refiling all complete as per specification and direction of E/I
Earth Work excavation (As per I.S3114/1965 for laying of different types and sizes of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of E/I.
Earth work in back filling the trenches after laying different types and size of pipes with earth removed during excavation within initial lead and lift as per specification and direction of E/I
Extra for earth work in all kind of soil for each additional 1mtr. Or part of there of over the lift of 1.5 mtr. As per specification and direction of E/I.
Providing and fixing G.M. non-return valve Horizontal/Vertical type of approved quality as per specification and direction of E/I. Vertical non-return valve
iv) 32mm dia weight not less than 600 gms.
v) 40mm dia weight not less than 700 gms.
vi) 50mm dia weight not less than 1 kg.
Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.
32 mm dia nominal bore
40 mm dia nominal bore
50 mm dia nominal bore
Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore
Painting GI pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality.
32 mm diametre pipe
40 mm diametre pipe
50 mm diametre pipe
Providing and filling sand of grading zone V or coarser grade, all- round the G.I. pipes in external work :
32 mm diameter pipe
40 mm diameter pipe
50 mm diameter pipe
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and makingchannels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :
Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Extra for depth for manholes : Size 90x80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Size 120x90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. All types of soil 400 mm dia
Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. All types of soil 400 mm dia
Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia
Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia
Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.
Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed/ plain bevel ended pipe (type A) of required dia, conforming to IS: 8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge. 200 mm diameter
Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.
Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia
Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp
Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 150 mm dia
Supplying submersible pump sets confirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/ noryl impeller. Motor suitable for working on 415V+10%, 3PH, 50 Hz, A.C. supply with cable guard, thrust carbon/ fiber bearing to with stand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non return valve shall be provided with pump. 3 meter submersible copper conductor cable in single/ double run shall be provided with each pump. Submersible Pump 150 mm dia (with Bronze Impeller) up to 12 stages 15 HP
Carriage of materials from source to site work including loading & unloading all complete job as per specification and direction of E/I
Stone Chips
Bricks
Supplying and fixing double door Horizontal TPN MCB Distribution board (Legrand make or other as per approved make list) with IP-42/43 protection, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment. 4+18 way Enclosure of Legrand make
Supplying and fixing double door Vertical TPN MCB Distribution board (Legrand make or other as per approved make list) with IP-42/43 protection, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment. 12 WAY( 8+36) Enclosure Vertial Type of Legrand MAKE
Supplying and fixing 240/415 V MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection. (Legrand make or other equivalent as per approved make list)
6-32 A SP MCB of Legrand
25/32 A DP MCB
40 A TPN MCB
40 A FP Isolator of Legrand
32 A TPN MCB
25/32 A FP Isolator of Legrand
25 A FP MCB of Legrand
Distribution wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) partly in 20mm size uPVC rigid conduit 'FR' (Precision make) [for horizontal run & above false ceiling portion only] and in 19mm bore, 3mm thick uPVC/ polythene pipe [for vertical run embedded in wall], with 1x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire for ECC, to light/fan/call bell points with Modular type switch (Brand approved by EIC) fixed on Modular GI switch board complete with 2 no. suitable size “Ph & N” copper bar with top cover plate making earthing attachment fixed on wall incl. mending good damages to original finish. [PVC Rigid Conduit only for horizontal run & above false ceiling and vertical run concealed] ( Make- wires - Finolex or equivalent as per approved make list, Modular switch - Legrand Arteor or equivalent as per approved make list).
Average run 5 mtr-GROUP-A
Average run 6 mtrGROUP-B
Average run 8 mtrGROUP-C
Distribution wiring in 1.1 KV single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) in suitable size of PVC rigid conduit 'FR' (Precision make) incl. necy. fittings as required. ( Make -Wire - Finolex or equivalent as per approved make list).
2x2.5 sq mm+1x2.5 sq mm earth wire.
2x4 sq mm+1x4 sq mm earth wire.
2x6 sq mm+1x6 sq mm earth wire.
Supply & Fixing 240 V, 6 A, 3 pin Modular type plug socket (Brand approved by EIC) with 6A Modular type switch, without plug top on 4 Module GI Modular type switch board with 3 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. (Make - Modular switch - Legrand Arteor or equivalent as per approved make list)
Supply & Fixing 240 V, 16 A, 5/6pin Modular type plug socket (Brand approved by EIC) with 16A Modular type switch, without plug top on 4 Module GI Modular type switch board with top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. (Make - Modular switch - Legrand Arteor or equivalent as per approved make list)
FITTINGS:Supply and Erection.
Fan Regulatar step type two module
BLANKING PLATE
Fixing only exhaust fan after making hole in wall and making good damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire and making connection for exhaust of following diameter:
300 mm exhaust fan.
LOVERS FOR 300 MM EXHAUST FAN
Wiring for 1.1 KV grade single core FR PVC Cu wire 4cx10+2x10 sq mm earth wire sq mm in suitable size of conduit as per spec.
Wiring for 1.1 KV grade single core FR PVC Cu wire 4cx16+2x16 sq mm earth wire sq mm
20 mm PVC Conduit for
25 mm PVC Conduit.
Supply & Fixing 240 V, 25 A, 3 pin Modular type plug socket with 20/25 A Modular switch type SP MCB and 4 module GI modular type switch board and 4 module top cover plate.
Supply of 2Cx6 Sq mm Al armoured cable
Laying of 2Cx6 Sq mm Al armoured cable in burried and filling with as per spec.
Termination of 2Cx6 Sq mm Al armoured cable
Telephone socket outlet
TV Antena socket outlet
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc.
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required
Wiring for 1.1 KV grade single core FR PVC Cu wire 4 x6 +2x6 sq mm in suitable size of conduit as per spec.
Distribution wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) partly in 20mm size uPVC rigid conduit 'FR' (Precision make) [for horizontal run & above false ceiling portion only] and in 19mm bore, 3mm thick uPVC/ polythene pipe [for vertical run embedded in wall], with 1x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire for ECC, to light/fan/call bell points with Modular type switch (Brand approved by EIC) fixed on Modular GI switch board complete with 2 no. suitable size “Ph & N” copper bar with top cover plate making earthing attachment fixed on wall incl. mending good damages to original finish. [PVC Rigid Conduit only for horizontal run & above false ceiling and vertical run concealed] ( Make- wires - Finolex or equivalent as per approved make list, Modular switch - Legrand Arteor or equivalent as per approved make list).
GROUP LIGHT POINT -GROUP-A
GROUP LIGHT POINT -GROUP-B
6 way SPN DB
4 WAY( 8+12) Enclosure of Legrand MAKE
OCTAGONAL POLE 10A DP MCB
Supply of following sizes of 1.1 kV grade XLPE insulated PVC sheathed armoured aluminium conductor power cables as per IS:1554(part-1&2) complete as required as per specification with make list.
3.5Cx300sqmm
3.5Cx240sqmm
3.5Cx185sqmm
3.5Cx150sqmm
3.5Cx120sqmm
3.5Cx95sqmm
3.5Cx50 sqmm
3.5Cx35 sqmm
4/3.5Cx25 sq mm
4Cx16 sq mm
4Cx10 sq mm
2CX16 sq mm
2Cx10 sq mm
Laying of cable in BURRIED AS PER SPECIFICATION.
3.5Cx300sqmm
3.5Cx240sqmm
3.5Cx185sqmm
3.5Cx120sqmm
3.5Cx95sqmm
3.5Cx50sqmm
3.5Cx35 sqmm
4 Cx25 sq mm
4Cx16 sq mm
4Cx10 sq mm
2CX16 sq mm
2Cx10 sq mm
2Cx6 sq mm
L.T CABLE TERMINATION OR END JOINTS AS SPEC WITH MAKE LIST.
3.5Cx300sqmm
3.5Cx240 sqmm
3.5Cx185sqmm
3.5Cx120sqmm
3.5Cx95sqmm
3.5Cx50sqmm
3.5Cx35 sqmm
4Cx25 sq mm
4Cx16 sq mm
4Cx10sq mm
2Cx16sq mm
2Cx10sq mm
2Cx6 sq mm
L.T CABLE JOINTING ST as per Spec
3.5Cx300sqmm
3.5Cx240sqmm
3.5Cx185sqmm
3.5Cx95sqmm
3.5Cx35 sqmm
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required(Required for lightining arrester)
Wiring for External JB to Eeternal light fittings.2X1.5+1X1.5 single core cuper conductor in PVC Conduit.
Wiring for External JB to Eeternal light fittings.2X1.5+1X1.5 single core cuper conductor Without PVC Conduit.
S/F PVC 4/5 Module base with cover plate and assasaries.
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing e.t.c as required
Supply and making cable route marker with cement concreate 1:2:4 of size 60x60 cm bottom and 50x50cm at the top with thickness 10 cm as requred.
Cable Tray
100 mm x50mmx1.6mm perforated type
150 mm x50mmx1.6mm perforated type
300 mm x50mmx1.6mm perforated type
450 mm x62.5mmx2 mm perforated type
600 mm x62.5mmx2 mm perforated type
500 KVA silent type DG with AMF PANEL
Laying of 3cx240 sq mm 33 KV GRADE in burried.
Laying of 3cx185 sq mm 33 KV GRADE in burried.
3cx240 sq mm 33 KV grade xlpe Alluminium cable in trench.
3cx185 sq mm 33 KV grade xlpe Alluminium cable in trench.
INDOOR JOINT(Heat Shrinkable)
3cx240 sq mm 33 Kv grade xlpe Alluminium cable.
3cx185 sq mm 33 Kv grade xlpe Alluminium cable.
OUT DOOR JOINT(HEAT SHRINKABLE)
3cx240 sq mm 33 KV grade xlpe Alluminium cable.
3cx185 sq mm 33 KV grade xlpe Alluminium cable.
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)
Supply of following sizes of 1.1 kV grade XLPE insulated PVC sheathed armoured aluminium conductor power cables as per IS:1554(part-1&2) complete as required as per specification with make list.
3.5Cx300sqmm use for capacitor panel
3.5Cx70sqmm for DCDB
Cable Laying in Tray
3.5Cx300sqmm use for capacitor panel
3.5Cx95sqmm for ACDB
3.5Cx70sqmm for DCDB
Termination of following cables
3.5Cx300sqmm
3.5Cx70 sqmm
ITC of 450 mm exhaust Fan
P/F M.V danger notice plate
P/F H.T danger notice plate
Supply, Installation, Testing and Commissioning of electric driven, horizontal type, single/multistage, end suction type, centrifugal pump of cast iron body, C.I impallers with carbon steel shaft & mechanical seal directely coupled with TEFC SQ cage foot mounted type induction motors suiitable for operation on 3 phase, 415 volts 50 Hz AC supply having flow rate of min 450 LPM and head of approx 40 mtrs complete in all respect as required or as directed by engineer incharge.
Main Fire Pump
Jockey Pump
Standby Diesel Engine Pump Set
Terrace Booster Pump
Air vassale made of 250 mm dia,8 mm thick MS sheet,1200 mm height and as per Dsr.
Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42. For Pump Room
Supply and fixing of PVC sheathed following conductor 1.1 KV grade armoured Cable of following sizes including making end termination with compression gland & bimetalic lugs, and support etc.complete as required
3.5 c × 50 sq.mm.(aluminium)
3.5 c × 35 sq.mm.(aluminium)
4 c × 10 sq.mm.(aluminium)
Providing and fixing IS marked Gate Valve / Foot Valve (incase of -ve suction) complete with companion flanges, bolts, nuts, rubber insetions etc.
150 mm diameter
100 mm diameter
Providing and fixing IS marked butterfly valve (PN 1.6) complete with companion flanges, bolts, nuts, rubber insetions etc.
80 mm diameter
100 mm diameter
150 mm diameter
Orifice Plate
Providing and fixing check valve (NRV) complete with companion flanges, bolts, nuts, rubber insetions etc.
80 mm diameter
100 mm diameter
150 mm diameter
Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.
Providing, laying, testing & commissioning of IS 1239 marked black M.S pipe including all fittings i.e bend, elbows, tees, flanges, reducing socket, nuts and bolts, gaskets etc fixed with welded / screwed joints. including necessary excavation, backfilling, removal of surplus soil etc. min. 1 mtr deep excavation and wrapping with anticorrosive treatement with 4 mm thick asphalt tape as per IS:10221, refilling the trench etc. OR fixed with screwed or welded joints, hanged with clamps, hanger supports, dash fasteners, bolts, nuts, rubber insertions etc including threading, cutting, welding, edge preparation, painting of approved colour over two coat of primer, cutting & making good the wall/ floor wherever required, complete as required or as directed by engineer incharge. Make:Tata/Nezone/Jindal
200 mm diameter
150 mm diameter
100 mm diameter
80 mm diameter
65 mm diameter
50 mm diameter
40 mm diameter
32 mm diameter
25 mm diameter
Providing and fixing S.S Fire Hydrant Valve of approved quality with 63 mm female, instant, ovlique, single outlet, 80 mm flanged inlet, brass spindle, cast iron wheel m A.B.S. blank cap and chain. conforming to IS: 5290 complete with companion flange, bolts, nuts, rubber insertion / compressed asbestos gasket etc. and painted in fire red colour.
Providing and fixing swinging, wall mounting type First Aid Hose Reel of approved quality and made from compresed steel sheet with dust cover, cast iron brackets including 30 m long, 19 mm nominal bore, high presure braided rubber hose as per IS:444 Type hose guide, PVC shut off nozzle with 6 mm outlet and 25 mm nominal bore gun metal inlet valve, bolts, nuts rubber insetion etc. painted in Fire red colour including cutting and making good the walls wherver required.
Providing and fixing in position 63 mm nominal bore and 15 m long synthetic fibre, CP fire hose pipe of approved make bearing IS: 636 -1988 type A mark and having TAC and MMD approved with a pair of 63 x 63 mm gun metal instantaneous type, heavy duty delivery hose coupling (conforming to IS: 903) bound and riveted to the hose pipe with copper rivets and copper wire complete.
Providing and fixing in position short SS brach pipe of approved quality with 63 mm male instatneous type inlet and 15 mm outlet nozzle complete conforming to IS : 903
Providing and fixing Standard response Upright / Pendant sprinklers (With Covers, white / ivory colour) with quartzoid bulb overating temperature 68 degree centgrade, of 15 mm orifice and k factor 80 (5,6) made out of forged brass and chrome finish. Make:Safex/Atasee/Tyco
Supplying, installation, testing & commissioning of sprinkler flexible pipe of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.
Supplying, fixing, testing & commissioning of 1 set of 63mm two way instantaneous fire brigade connection (FBC) with inbuilt NRV comprising of SS and four SS instantaneous male inlet coupling confirming to IS:604 with plug and cap with chain as required with nut & bolts, washers, high pressure gasket as required.
Supplying, installation, testing and commissioning of optical type Smoke detector and mounting base with LED light complete as required. Make:Qutak/Honeywell/Seimens/Bosch
Supplying, installation, testing & commissioning of response indicator on surface/recessed having two LED with cover complete with all connections etc as required
Supplying, installation, testing and commissioning of duel tone electronic hooter / Flasher / Strobe suitable for wall mounted complete as required. Make:Honeywell/Seimens/ Qutak/ Bosch
Supplying, installation, testing and commissioning of manual call box in suitable enclosure with arrangement to raise the alarm when the glass is manually broken complete as required. Make:Honeywell/Seimens/Qutak/Bosch
Supplying, installation, testing and commissioning of microprocess base main fire alarm control panel with LCD Display lights. The panels shall have 240 volts AC power supply automatic Battery charger 24 Volts sealed lead acid maintenance free battries as complete with batteries, battery charger illuminated numeric digram complete as required. Make:Honeywell/ Seimens/ Qutak/ Bosch
Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required. Make:Honeywell/ Ahuja/ Bosch
Supplying, installation, testing & commissioning of ceiling/wall mounted Pubmic announcement speaker, 3/1.5 Watt in ABS enclosure complete as required. Make:Honeywell/ Ahuja/ Bosch
Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required. Make:Honeywell/ Ahuja/ Bosch
Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required. Make:Honeywell/ Ahuja/ Bosch
Providing and laying 19mm dia PVC conduit complete with required junction boxes in recessed / surface system PVC insulated copper conductor cable of 2x1.5 sq.mm. in existing conduit as required.
Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.
200mm thick (GSB) By Mix in Place Method Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 For Grading- I Material
250mm thick Wet Mix Macadam Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.With vibratotry Roller
Prime coat Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means.
Tack coat Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom.
50mm thick Dense Graded Bituminous Macadam (DGBM) Dense Graded Bituminous Macadam (Providing and laying dense bituminous macadam with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 to 4.5% by weight of total mix of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 507 complete in all respects.) with Modifed Graded Bitumen.For Grading I ( 40 mm nominal size )
40 mmThk. Bituminous Concrete (BC) Bituminous Concrete (Providing and laying bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 % of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 509 complete in all respects). For Grading-I ( 13 mm nominal size )
Providing and laying at or near ground level factory made kerb stone( size Bottom width - 165mm. , Top width - 115 mm. , Height - 250 mm.) of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).
Providing and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per manufacturer’s specifications &direction of Engineerin-Charge. 80mm thick C.C. paver block of M-30 grade with approved colour, design & pattern.
Painting road surface marking with adequate nos of coats to give uniform finish with ready mixed road marking paint conforming to IS : 164, on bituminous surface in white/yellow shade, including cleaning the surface of all dirt, scales, oil, grease and foreign material etc. complete. New work (Two or more coats)
Carraige of Material (Valid for JSR item only) (Payment will be made as per chart of carriage of JSR ) Upto 1 KM.
Lime , Moorum - Local -lead 11 km
Stone metal - Jhona , lead 22 km.
Tar / Bitumen
CUTTING FOR GRADING :-Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.Note:- (Payment will be made in cubic meter on the basis of quantity arrived at site on pre-work and post work level Section measurements for Cutting & filling also)
All kinds of soil
Ordinary rock
Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.
Supplying and stacking at site.Moorum
Horticulture & Landscape Works Note: The Agency have to maintain the total project at least 12 month after completion of total work and handing over.Total tools, tackles, machinery, equipments etc are to be arranged by the agency and no extra cost would be paid for that. The Agency have to bear the cost of manure required for the job and during maintenance period of 6 month without any extra cost.Required Anti-termite treatment shall be done by the Agency without any extra cost. Cost of required Pest control chemical charges shall be born by the Agency without any extra cost. All unhealthy, dead plants, spotted and dead grasses to be replaced by the agencies with out any extra cost up to the end of maintenance period. All the grassing area are to be smooth and free from any type of foundation. Agency has to spread sand, fine clay etc or any required materials as required to maintain the grassing are smooth and free from any undulation with out any extra cost up to the end of maintenance period.
SITE PREPARATION Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment).
Supplying and stacking sludge at site including royalty and carriage upto 5 km complete (sludge measured in stacks will be reduced by 8% for payment).
Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge
Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).
Fine dressing of the ground.
Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)
Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : Holes 90 cm dia, and 90 cm deep
Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Hedge Plant
Trees Plant
Shrubs Plant
Hedge Plant
GROUND COVER Providing and Displaying of Duranta Golden plant, having ht.15 to 20 cm bushty shape plant with fresh and healthy leaves in 20 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge.
Providing and Displaying of Clerodendron inerme plant of ht. 30 cm to 40 cm multi branched in 25 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge.
Providing and Displaying of Alpinia Variegated (three in one) plant having ht. 30 cm and above , with fresh and healthy variegated foliage in 25 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge
WINTER PLANTS Providing and Displaying plants Allyssum white in full bloom well developed fresh & healthy Plant in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
Providing and Displaying plants Brachycome well developed with fresh & healthy foliage with 100 to 120 flowers stacking with green painted bamboo stick in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer in- charge.
SUMMER & RAINY SEASONAL Providing and Displaying plants Celosia well developed fresh & healthy 20 to 25 cm ht. (attractive) multi branching at blooming stage in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
Providing and Displaying plants Sunflower single well developed 8 to 10 half bloom buds multi branched in fresh & healthy full stacked with green painted bamboo stick stacking in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge
ROSE PLANTS Providing and Displaying plants Creeper Rose variety 3 to 4 healthy branch 60 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge.
Providing and Displaying plants Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge.
CREEPER PLANTS Supply and stacking of Bougainvillea (Variety Butiana, Lady Mary Baring,Mahara,Mohan,Scarlet Queen, Varigata, Glabra Formosa, Peruviana Odissi,Partha, Subhra,Thimma, Spectabilis L.N Birla, Refulgens) plant of height 30 cm. to 45 cm. with 2-3 branches in 20 cm size of Earthen pots /Plastic pots & as per direction of the officer-in-charge. .
TREE Supply and stacking of Mangifera indica (Mango-grafted ) plant of height 60-75 cm. in big poly bag of size 25 cm as per direction of the officer-incharge.
Supply and stacking of Bassia latifolia (Mahua) plant of height 90-105 cm. in big polybag of size 25 cm as per direction of the officer-in-charge.
Supply and stacking of Azadirachta indica ( Neem ) plant of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.
Supply and stacking of Bauhinia purpurea (Kachnar) plant of height 150- 165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge
Supply and stacking of Bombax ceiba plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
Supply and stacking of Albizzia lebbek plant of height 150-165 cm. in bag of size 25 cm as per direction of the officer-in-charge
Supply and stacking of Tamarindus indica (Imli) plant of height 120-150 cm. in big polybags of size 25 cm as per direction of the officer-in-charge.
Supply and stacking of Delonix regia (Gulmohar) plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge
Supply and stacking of Jacaranda mimosifolia plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
Supply and stacking of Nauclea cadamba (Kadam) plant of height 150-165 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.
Supply and stacking of Bottle palm plant of ht. 270-300 cm bottom girth 40-50 cm well developed in big HDPE bags as per direction of the officer-in-charge
Supply and stacking of Tectona grandis (Teak) plant of height 150-165 cm.in big polybags of size 25 cm as per direction of the officer-in-charge.
Supply and stacking of Polyalthia pendula (Ashok Pendula) plant of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-incharge.
Supply and stacking of Phyllanthus emblica (Amla) plant of height 150-165 cm. in Big HDPE Bag as per direction of the officer-in-charge.
Supply and stacking of Ficus religiosa (Peepal) plant of height 150-165 cm. in big poly bags of size 30 cm as per direction of the officer-in-charge. Each
Making tree guard 53 cm dia and 2 m high as per design from empty coal tar drums, supplied free by the department, including providing and fixing four legs 40 cm long of 30 x 3 mm M.S. flat riveted to tree guard and providing and fixing 2 nos. M.S. sheet ring 50 x 0.5 fixed with rivete complete in all respect including painting inside and outside of tree guard with : Two or more coats of synthetic enamel paint of approved quality and shade over a priming coat
ANNUAL MAINTENANCE (FOR 2YEARS AFTER 1 YEAR OF LIABILITIES)-Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide ,Pesticide , lawn mover and brush cutter with fuel will be provided by the Department & other T & P material/articles shall be provided by the contractor.). Open spaces(as per yard stick 1Mali =3.00Acre).
FOUNTAIN Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge:
Non- Schedule items
(The Contractor shall give a 10-year service guarantee in writing supplemented by a separate and unilateral guarantee from the pre approved specialised agency for the job to keep the building free of termites for the specified period at no extra cost to the owner.) Anti termite treatment with chemical (Imidaclprid 30.5 SC) shall be used at 0.075% concentration (2.1 ml of chemical mixed in 1 ltr of water OR in other words mixing ratio of chemical to water is 1:475) with water by weight at the rate of 5 Liters per sq. m.of the surface before sand bed is laid. (For top surface of the consolidated earth at plinth holes upto 50 mm. to 75 mm. deep at 150 mm. center to center both ways shall be made with 12 mm, diameter mild steel rod on the surface to facilitate saturation of the soil and also to the Foundation bed ,Basement excavation, back filling Vertical side, Plinth & extended portion ,Soil Surrounding Pipes, Wastes and Conduits, special care at below construction joints, beneath Junction of the Wall and the Floor etc. with the chemical as above) .The work should be carried out as per specification described in para 6.4 of code IS-6313 (part-2&3) 2013 by a specilised agency duly preapproved. ( Mode of measurement will be per Sqm of Plinth area of the Building as per Drawing.)
Supplying and laying of Polythene Sheet ( 400 micron) of approved quality over damp proof course or below flooring /foundation PCC in at any Level, in tie beam , at any level, at any floor complete in all respect.
Supplying, laying and fixing of std. chicken wire mesh flexible galvanized steel wire with hexagonal gaps. Available in 1 inch (about 2.5 cm) diameter, wire gauges 19 gauge (about 1 mm wire) to 22 gauge (about 0.7 mm wire). in positions at junctions of concrete & masonry works etc. all complete as per specification, drawing and instructions of the Engineer in charge.
Providing Anchor dash fastener mechanical/Chemical for Door Frame Fixing With RCC Column.
Providing & fixing 18mm thk Granite door frames of any approved colour (No joint allowed) upto full plastered wall width vertical 2pcs. both amalgamated with approved quality bonding adhesive in vertical jambs & soffit, as per drawing & design fixed on walls with necessary backing material, & 90mm long stainless steel screw (3 nos. each vertical stone ) with rawl plug including machine polish , necessary edgemoulding , each smooth joint, providing position for hinge & rivet for shutter on exposed edges and rounding of corners, and joint filling compound of same shade of Granite with all Lead & Lift,royalti,taxes etc. complete in all respect as direction of Engineer in Charge.
Providing vision panel in flush doors using 4mm thick weight not less than 10kg/sqm (cost of glass included ) complete in all respect as per direction of Engineer in charge.(Vision Panel area to be mesured)
Providing Stainless Steel Butt Hinge 100 X 60 X 2.5 mm of approved make (Godrej or equivalent) including necessary screws etc.
Providing & Fixing Door Pull Handel SS304 - D-Type (25 dia. X 450 mm) of approved make (Godrej or equivalent) including necessary screws etc.
Providing & fixing SS304-Push & Pull Handle H-Type (32 dia. X 457 mm) complete in all respect as per Engineer in charge
Providing & Fixing 4 Lever Mortise Lock Combipack with Legend Chrome Handle Set for Single Leaf Door Shutter of approved make (Godrej or equivalent) including necessary screws etc.
Providing & Fixing SS 10x 300 mm Tower Bolt for Door of approved make (Godrej or equivalent) including necessary screws etc.
Providing & Fixing SS Stopper for Door of approved make including necessary screws etc.
Providing & Fixing SS Indicator Lock for Toilet Door of approved make including necessary screws etc.
Providing & Fixing SS Mortise Lock for Single Leaf Shutter Door (Body with Cylinder & Keys) of approved make including necessary screws etc.
Providing & Fixing SS Lock for Double Leaf Shutter Door (Body with Cylinder & Keys) of approved make including necessary screws etc.
Providing & Fixing Door Handle(Type-1) for Door Shutter of approved make & design including necessary screws etc.
Providing & Fixing Door Handle(Type-2) for Door Shutter of approved make & design including necessary screws etc.
Providing & Fixing Special SS Lock for Toilet Door Shutter of approved make & design including necessary screws etc.(MLA Residence Only)
Providing & Fixing Channel & necessary rollers & fittings fixture for sliding Door of approved make & design including necessary screws etc.
Providing & fixing SS D type Handle 300 mm dia/Other type Handle for aluminium door
Providing & fixing Aluminium Louver complete in all respect as per direction of Engineer in charge.
Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 40 kg ), with necessary accessories and screws etc. complete.
Providing and fixing SS Tower Bolt 450mmX 10mm of approved make including necessary screw etc. complete in all respect.
Supplying and fixing Dash fastener complete in all respect.
Providing & fixing 8 mm. thick toughened glass of approved make complete in all respect as per direction of Engineer in charge.
Providing & fixing 6 mm. thick toughened solar controlled glass of approved make complete in all respect as per direction of Engineer in charge.
Providing & fixing 4 mm. thick frosted glass of approved make complete in all respect as per direction of Engineer in charge.
Design, supply fabricate and fixing Semi Utilized Structural Glazing system with double (DGU) /single glazing for Door portion securely bonded to framework to ensure absolute water tightness, with profile either straight or segmented curve in plan consisting of main panel work of Mullions and Transoms made out of specially designed extruded aluminium section having 15-20 Microns Anodized in approved colour. Fixed at all levels, elevation and heights to the RCC elements with necessary clamps,brackets and anchor fasteners, made of shall be Mild steel Hot Dip galvanized with washer and shall confirm to IS : 4759 -1996. All gaskets shall be EPDM with all necessary flashing, floor seal, smoke seal, sealants etc. to make system fully weather and sound proof & water tight. Proposed glazing should be bonded to frame by mean of Structural sealant of Dow cornice995 and weather sealant shall be Dow Cornice 789. All spacer tape should be Norton or equivalent etc. complete with fixing Glass inclusive of all except supply of Glass will be paid separately.(Glass fixing charges, Shutter Hardware of approved quality included in this item)
(a) For Spandrel or Fixed Area
(b) For Vision or Openable Area
Extra for Hardware over Aluminum Work for Providing & fixing necessary/suitable hinge for aluminium Door & window , PVC Handle with SS lock of approved make for aluminium Window.(Except Aluminium Door Handle)
Providing and fixing preapproved Kota stone slabs of 20 mm thick semi polished in trader of steps with single piece with 20mm thick base of cement mortar 1 : 4 (1 cement : 4 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete with Single piece all lead & lift.
Providing and fixing preapproved Kota stone slabs 20 mm thick semi polished in risers of steps with single piece laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete with Single piece all lead & lift.
Labour charges for antiskid groove 3 nos. in treads of steps of Kota stone as per design.
Providing and laying (Matt/Antiskid) Ceramic floor tiles of size as mentioned below (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make and approved colours and design, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete with all lead & lift. Size- 300mmx300mm
Providing and laying Matt finished vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.
For Sizes 800mmX800mm .
For Sizes 600mmX600mm .
Providing and laying Digital vitrified tiles in floor different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. in floor Size of Tile 800 x 800 mm.
Providing and laying Wall Vitrified tiles in different sizes in skirting (thickness to be specified by manufacturer), with water absorption less than 0.08 % , of approved make, in approved design & colour, in dado, skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete with all lead & lift.
For Sizes 800mmX800mm .
For Sizes 450mmX300mm .
Providing and fixing Pre approved Granite stone slab 18mm thick semi polished in trader of steps with single piece & Landing of steps with single piece over 22mm thick base of cement mortar 1 : 4 (1 cement : 4 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete with Single piece all lead & lift. * Provision for Stair case railing baseplate square hole should be maintained.
Providing and fixing Pre approved Granite stone slab 18 mm thick semi polished in risers of steps with single piece/Skirting & Dado laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete with Single piece all lead & lift.
Providing and fixing Carpet Flooring using (Roll type) carpet of approved make shade and pattern and of the following specification: Tufted cut pile, 1/10 gauge with 100% Polyamide Millerton/ 6 Crayon (R) nylon/ SD Nylon pile or equivalent material having minimum surface pile thickness of 5.3 mm and minimum total thickness of 7.1 mm with Contract Latex backing/ 'Weave back (R) backing/ Woven Polypropylene backing, min. tufts of 201500 per sqm and minimum total carpet weight of 2300 g/sqm, minimum pile yarn weight of 1200 g/sqm, minimum surface pile density of 0.141 g/ cecum having inbuilt anti-soiling protection, suitable for commercial-heavy use areas like auditorium application, having acoustical insulation value of 31 dB, CE labeled, EC certified, fulfilling Fire Classifications EN 13501-1 euro class and approved by Green Label Plus test for indoor hygiene in standard length and width.
Supply fitting & finish of Indoor synthetic 5.0mm bwf(Badminton world federation)approved badminton court synthetic flooring. Color: GreenColor: Green,Thickness: 5.0mm, make: EnlioThickness: 5.0mm, make: Enlio Dimension of roll: 1.8mtx15mtx4 roll Laying with both side adhesive tape After laying the floor weld 5mm same color welding cod& Playing game line markings same.
Supply fitting & finish of 10mm epdm gym rubber flooring 10mm interlocking tiles
NOTE FOR WATER PROOFING WORK:- a) The contractor shall get written approval from the Engineer- in- charge, for water proofing work , Special agency from manufacturer recommendation was engaged their sound applicator and shall submit detail procedure of application alongwith specification. b) The contractor shall furnish guarantee bond on appropriate stamp paper for the entire waterproofing treatment for maintaining the surroundings and under side surfaces of the waterproofing treated area in bone dry condition for 10 years. During the guarantee period the contractor shall attend and rectified all leakages, defects etc. if noticed, free of cost, within a day's time from the date of intimation about such leakages/defects. c) The contractor shall test the surface where water proofing treatment provided for bone dry condition by filling up with water. No wet patches or leaks shall appear on the surrounding wall or under side of the slab. d) The Contractor shall keep the water proof area filled with water after the water proofing work has been completed for testing of leakage and shall clean it before handing over. Faulty area shall again be done, before handing over the , if found necessary by the Engineer- in-charge.
Waterproofing of Roof or Open terrace
Water proofing for Old and New Roof Slab Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible material applied with brush, roller or spray for water proofing coating as per manufacturer specifications with following steps
(a) Surface preparation :-Providinga and cleaning of concrete surface to remove dust, oil, grease including removal of existing loose paint / coating, and cement laitance by Cleaning with compressed air & water jet including all materials, labour, tools complete.' Ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage,leakage. On identification of seepage cement grouting be done with non shrink expanding admixture of Slka Indi Pvt Ltd/MYK Schomberg/ Dr Fixit/Fosroc or eqüivallente.Provtding and reparing of all corners and joints such as those between thr parapet wall and the roof slab etc. shall be chamfered with 150mm X 50 mm fillet of mortar (Cement: sand 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent. Before chamfering a prime coat shall be given with the slurry of acrylic polymer . Repairing surface irregularities, damaged concretein base slab dead cracks if any, with an acrylic polymer modified repair mortar inc!uding a coat of bonding agent of the same with cement slurry including all material, labour, tools complete.
(b) 1st Coat :-Apply 1St coat of two component acrylic modified, ready to use, flexible cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roller. After 1st coat of application 45 gsm of Fibre glass cloth to lay when the first layer is still green. 1st coat shduld be applied @1.50 kg/Sqrni/coa!. For the purpose of measurement the entire treated surface will be measured.
(c) 2nd Coat:-TO apply the 2nd coat of two component acrylic modified, ready to use, flexible cementitious material right angle to the Ist coat over the glass fibre laid surface. 2nd coat should be [email protected]/Sqmt/coat. For the purpose of entire treated surface will be measured." After three days of drying the 2nd coat , the rain water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification to be done as per satisfaction of E/C. The waterproof coating to be protected from damage before screed over it. Waterproofing Brand:-Sika -Topseal 109hi / Fosroc Brushbond RFX/Dr Fixit Pidiffin 2K / MYK Aquafin TG. Product Performance. Chemical Base Part A: Acrylic copolymeri Part B: Specially graded cementitious powder - Density 1.6 kg/l (mixed density) at + 27 degree C Tensile Strength — 2 N/mm2 after 28 days (with Fibre cloth) (According to ASTM D 2370) Pullout Bond Stren th —2 N/mm2 concrete failure Accordin to ISO 4624) Slant . Shear Bond Strength-4N/Sqmm(According to FIP 5.15). Elongation at break-35% without Fibre Cloth and 20% with Fibre Cloth (According to ASTM D 2370).
Providing and Laying Polysulphide sealent as per direction of Engineer in Charge
Waterproofing of Overhead Reservoir:
Providing and laying water proofing treatment on Overhead reservoir consisting of following :-(Measurement on treated floor & wall area separately & Rate is inclusive all items)
1.Surface Preparation: All surfaces to receive the waterproofing to be mechanically cleaned properly so that there will be no dust, laitance, oil, grease etc. (To check a pond test to find out sign of seepage from soffit. On identification of week concrete, seepage through joints and honeycomb necessary grouting to be done with suitable material of approved manufacturer with their direction with contractor's own cost)
2.Coving:Coving to be done at all junctions by cutting V grooves of prescribed size and filling with cement-sand (1:4) mortar admixed with ( Sika Top 77 /Fosroc Nitobond SBR Latex/BASF Master Emaco SBR 2) of approved manufacturer with their direction.
3.Bore Packing: Bore packing to be done at all pipe entries with suitable material(Sika Rep Microcrete 4/Fosroc Conbextra GP2/BASF Master EMACO S340) food grade certified of approved manufacturer with their direction.
4.Water proofing product:-Supply and apply on floor & wall an acrylic based, ready to use, food grade certified water proofing product of minimum thickness 2mm (Sika Topseal 107/Fosroc Nitocote CM210/BASF Master Seal 550) as per approved manufacturer with their direction.
5.Covering with Screed plastering:-After curing Providing and applying 12mm thick plastering with Cement Mortar 1:4 admixed with integral waterproofing admixture (Sika Plastocrete Plus/Fosroc Conplast WL/BASF Master PEL 777) of approved manufacturer with their direction on wall & floor.
6.Finishing:-Finishing with Neat cement punning over plastering work.
Waterproofing of Underground Reservoir(Potable water):
Providing and laying water proofing treatment on Underground Reservoir for potable water consisting of following :-(Measurement on treated area Floor & wall separately and Rate is inclusive all items)
1.Surface Preparation: All surfaces to receive the waterproofing to be mechanically cleaned properly so that there will be no dust, laitance, oil, grease etc.
2.Coving:Coving to be done at all junctions by cutting V grooves of 20 mm x 20 mm and filling by cement-sand (1:4) mortar admixed with (Sika Top 122HS/Nitobond SBR Latex/Master Emaco SBR 2) of approved manufacturer with their direction.
3.Bore Packing: Bore packing to be done at all pipe entries with suitable material(Sika Rep Microcrete 4 /Fosroc Cebex 100 /BASF Master Emaco S 340) food grade certified of approved manufacturer with their direction.
4.Water proofing product:-Supply and application of a non shrink, expanding grout admixture with suitable food grade certified material (Sika Intraplast EP/ FOSROC CEBEX 100/ BASF Master Flow 150 ) of approved manufacturer with their direction, by pressure grouting inside RCC floor & wall after 28 days of curing using 12mm dia, 75 mm long GI nozzles 1.5 m C/C in the concrete.Next Supply and application of an water proofing inside RCC floor & wall upto plinth appropriate coating of minimum thickness 2mm(Sika Topseal 107/ FOSROC CM 210/ BASF Master Seal 550)of approved manufacturer with their direction.
5.Covering with Screed plastering:-After curing Providing and applying 12mm thick plastering with Cement Mortar 1:4 admixed with integral waterproofing admixture (Sika Plastocrete Plus/Fosroc Conplast WL/BASF Master PEL 777)of approved manufacturer with their direction.
6. Finishing:-Finishing with Neat cement punning over plastering work.
Waterproofing of Swimming Pool/Underground Reservoir(Service water):
Providing and laying water proofing treatment on Underground Reservoir for service water consisting of following :-(Measurement on Treated floor & wall area separately & Rate is inclusive all items)
1.Surface Preparation:-All surfaces to receive the waterproofing to be mechanically cleaned properly so that there will be no dust, laitance, oil, grease etc.
2.Coving:-Coving to be done at all junctions by cutting V grooves 20 mm x 20 mm of prescribed size and filling with cement-sand (1:4) mortar admixed with (Sika Top 77 /Nitobond SBR Latex of FOSROC/BASF Master Emaco SBR 2 ) of approved manufacturer with their direction.
3.Bore Packing:-Bore packing to be done at all pipe entries with suitable material(Sika Rep Microcrete 4 /Fosroc Conbextra GP2/ BASF Master Emaco S 340) food grade certified of approved manufacturer with their direction.
4.Water proofing product:-Supply and application of a non shrink, expanding grout admixture with suitable material (Sika Intraplast EP/ FOSROC Cebex 100/Dr.Fixit Pidicrete AM/Master Flow 150) of approved manufacturer with their direction, by pressure grouting inside RCC floor & wall upto Ground Floor(upto 3.00mtr.) after 28 days of curing using 12mm dia, 75 mm long GI nozzles 1.5 m C/C in the concrete.Next Supply and application of an water proofing inside RCC floor & wall upto plinth appropriate coating (Sika Topseal 107/FOSROC CM 210 /BASF Master Seal 550 of approved manufacturer with their direction.
5.Covering with Screed plastering:-After curing Providing and applying 12mm thick plastering with Cement Mortar 1:4 admixed with integral waterproofing admixture (Sika Plastocrete Plus/Fosroc Conplast WL/BASF Master PEL 777 ) of approved manufacturer with their direction.
6. Finishing:-Finishing with Neat cement punning over plastering work.
Waterproofing of Wet Floor areas:
Providing and laying water proofing treatment on Toilet, Pantry & Balconies floor slab consisting of following :-( Rate is inclusive all items except mentioned. Floor to be Prepared as required Level providing 1:5:10 Conc. Paid in separate item)
1.Surface Preparation: All surfaces to receive the waterproofing to be mechanically cleaned properly so that there will be no dust, laitance, oil, grease etc. (To check a pond test to find out sign of seepage from soffit. On identification of week concrete, seepage through joints and honeycomb necessary grouting to be done with suitable material of approved manufacturer with their direction with contractor's own cost)
2.Coving:Coving to be done at all junctions by cutting V grooves of 20 mmX 20 mm at Junction and filling with cement-sand (1:4) mortar admixed with (Sika Top 77 /Nitobond SBR Latex of FOSROC/ BASF Master Emaco SBR 2) of approved manufacturer with their direction.
3.Bore Packing: Bore packing to be done at all pipe entries with suitable material (Sikaflex 11 FC/Fosroc Nitobond SBR Latex/ BASF Master Emaco S 340) of approved manufacturer with their direction.
4.Water proofing product:-Supply and apply water proofing coating of minimum thickness 2mm (Topseal 107/Brushbond RFX/Dr.Fixit Pidifin 2K/Master Seal 550) on floor, polymer modified product as per approved manufacturer with their direction.
5.Covering with Screed plastering:-After curing Providing only integral waterproofing admixture (Sika Plastocrete Plus/Fosroc Brushbond RFX/BASF Master PEL 777) of approved manufacturer & direction for portion. ( Note:-1. Using this admixture mixing with mortar for backing mortar using for Floor finish item under supervision of waterproofing agency for no damage of treated area. 2. Floor finishing will be done over sand cement mortar will be paid in separate item)
Waterproofing of Wet wall areas:
Providing and laying water proofing treatment on Toilet, Pantry & Balconies Wall consisting of following :-( Rate is inclusive all items except mentioned)
1.Surface Preparation: All surfaces to receive the waterproofing to be mechanically cleaned properly so that there will be no dust, laitance, oil, grease etc.
2.Bore Packing:-Bore packing to be done at all pipe entries with suitable material (SikaRep Microcrete 4 /Fosroc Conbextra GP2/BASF Master Emaco S 340) of approved manufacturer with their direction.
3.Water proofing product:-Supply and apply water proofing coating wall upto2400mm above the final finished floor level., polymer modified product (Topseal 107/Brushbond RFX/Master Seal 550) as per approved manufacturer with their direction .
4.Covering with Screed plastering:-After curing Providing only integral waterproofing admixture (Sika Plastocrete Plus/Fosroc Conplast WL/ Master PEL 777) of approved manufacturer & direction for mixing ratio. ( Note:-1. Using this admixture mixing with mortar for backing mortar using for Dado finishing item under supervision of waterproofing agency for no damage of treated area. 2.Dado finishing will be done over sand cement mortar over water proofing surface will be paid in separate item)
Supply & fixing built-up panel made of two sheets and insulation in between. Top and bottom layer would be made of colour coated “LYSAGHT TRIMDEK 1015” profile sheet manufactured by Tata BlueScope Steel having nominal 1072 mm supplied width nominal 28 mm deep ribs with subtle square fluting in the five pans at nominal 203 mm centre-to-centre. The end rib shall be designed for anti-capillary action, to avoid any seepage of water through the lateral overlap. with Glasswool 50mm thick, 24Kg/m3 with 0.05mm thick aluminum foil complete in all respect as per direction of Engineer in charge.
Ridge / Corner / Gable Flashing, 0 - 610 MM Girth, 0.47 mm TCT, [COLORBOND Steel] Supply and fixing 0 to 610 mm Girt Flashings manufactured out of nominal 0.42 mm Base Metal Thickness (BMT), 0.47 mm Total Coating Thickness (TCT) Hi-strength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 45% Zinc) as per AS 1397 – Zincalume® AZ150 (Min. 150 gms/sq.mt total on both sides) with Colorbond® steel quality paint coat as per AS/NZS 2728
Providing & Fixing 10mm thick solid compacted transperent sheet with both side UV coating having 10years warrenty of approved make & size, complete in all respect with all required accessories as per Engineer in charge.
Auditorium wall panelling - Supply and installation of Stretchable acoustical fabric NRC fabric system by using FR Grade NRC fabric from Wall track / Anutone or equivalent Acoustic of size 1700 mm width, shall be stretched by using wooden 10/15 mm plywood strip support base to fix rigid vinyl stretch tracks half wrap/ full wrap 15 mm FS15 & mid seam 15 mm FS 15, 15 mm pinewood magnesia bonded strand board, Synthetic poly-fibre 5x25 infill with requisite accessories & tools. Pinewood wood-based wool fibre shall have 15 mm thick square
edge. Magnesite bonded pinewood fibres panels of size 600 x 1200 x15 mm having density 400 Kg /m3, weight 4 kg is first installed on the GI Channel CC25 on sidewalls which prefixed with adhesive / screw-on vertical wall insulation with TECSOUND 50 high density viscoelastic synthetic membrane roll size 1200 x 6000x 2.5 mm stick on the wall with overlapping of 100 mm to each other. Now place the GI framework on the top at 600 mm centres vertically / horizontally with suitable fasteners. Now apply stick S7 adhesive on the top face of wood wool strand panels to stick the Synth PF wool 5 x 25 mm thick adhered on strand tracks by following the fabric thread line or pattern. The fabric NRC is stretched & tucked into the stretch tracks & secure into the locking jaws so that it will be smooth, free of wrinkles with the tucking tools. Note - Minimum 50 mm additional fabric is required for tucking hence maximum module wall fabric width would be 1600 mm The technical parameters of the system are core - pinewood fibre & poly-fibre Fire - 1 Acoustic - NRC 0.85 Climate OCRH - 49, 90 Termite resistance - yes, light reflectance - colour dependant, Green RC % - 25, Hygiene ( Voc, Clean room ) - Low, Class 1. A test certificate will be submitted after the procurement of materials.
TOILET cubical Marino or Equivalent make FMRSCUBTTNZZSS00001 (HSN CODE : 48230000) BESCO CUBICLE TITAN SS 1980MM Thickness of Compact Laminate : 12mm Color of HPL Boards: Single Standard Compact Color Special Remarks For Customizaon : N/A : Size of Cubicle : As per Drawing (W) X 1550mm (D) X 1980mm (H) Door Size : 1750mm (H) X 600mm (W) Divider Size : 1775mm (H) Overall Height Of Cubicle : 1980mm (Including boom Gap of 150mm) Accessories: Standard - Merino Make Stainless Steel - 304 Grade accessories) a) SS "U" Channel b) SS "F" Channel (Only Corner Unit) c) SS Door Stopper Channel d) SS Top Rail e) SS Coat Hook f) SS Privacy Thumb turn c/w Occupancy Indicator g) SS Door Knob h) SS Spring Loaded Bu Hinges with Cover i) SS Adjustable Foot - 316 Grade j) Rubber Lining for Door Stopper k) S.S.Screws 304 G & P .V.C Wall Plugs SPECIAL NOTE - Warpage Criteria is 3.0 mm/1000mm for MRS panels as per EN standard- 438.
URINAL MODESTY SS FMRSUMPPNLZZSS00001 (HSN CODE : 48230000)URINAL MODESTY SS Thickness of Compact Laminate : 12mm Color of HPL Boards: Single Standard and Plain Compact Color Special Remarks For Customization : N/A Size of UMP : 500mm (W) X 1200mm (H) Overall Height Of UMP : 1850mm (Including bottom Gap of 650mm) Accessories: Standard - Merino or equvalent Make Stainless Steel - 304 Grade accessories) - SS a) SS Right Angle Brackets b) S.S.Screws 304 G & P.V.C Wall Plugs SPECIAL NOTE - Warpage Criteria is 3.0 mm/1000mm for MRS panels as per EN standard- 438.
Wood composite panel for gate of HARDYPLAST WC OR EQUIVALENT
Supplying & fixing factory made 30mm thick Metal Door SIZE 1200MM(W)X2100MM(H) Single Leaf Shutter painting with suitable colour over primer Including Hardware (6nos. 100mmx75mmx3mm MS Butt Hinge, 2nos.300mm Long D-Type MS Handle Fabricated MS 20mm dia ROD, 2 nos.250mm Aldrop) complete in all respect as per direction of Engineer in charge.
Supplying & fixing factory made 30mm thick Metal Door SIZE 1200 MM(W) X 2400 MM (H) Single Leaf Shutter painting with suitable colour over primer Including Hardware (6nos. 100mmx75mmx3mm MS Butt Hinge, 2nos.300mm Long D-Type MS Handle Fabricated MS 20mm dia ROD, 2 nos.250mm Aldrop) complete in all respect as per direction of Engineer in charge.
Supplying & fixing factory made 30mm thick Metal Door SIZE 1000MM(W)X2100MM(H) Single Leaf Shutter painting with suitable colour over primer Including Hardware (6nos. 100mmx75mmx3mm MS Butt Hinge, 2nos.300mm Long D-Type MS Handle Fabricated MS 20mm dia ROD, 2 nos.250mm Aldrop) complete in all respect as per direction of Engineer in charge.
Supplying & fixing factory made 8mm thick Metal Door SIZE 5000MM(W)X2100MM(H) Folding Leaf Shutter with MS Louver painting with suitable colour over primer Including necessary Hardware like handle, hinge & Locking arrangement complete in all respect as per direction of Engineer in charge.
Providing & fixing Floor spring SS material & SS finish for weight upto 80kg with necessary nuts screw etc. for flush Door shutter of approved Make complete in all respect.
Providing and laying Pool tiles in different sizes (minimum size 247mmX122mmX8mm), with water absorption less than 0.08% and conforming to relavent IS code, of approved brand & manufacturer, in all colours and shade,in flooring, in wall, in steps as per drawing laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including epoxy grouting of joints having joints of 3 mm width,complete in all respect as per direction of E/I.
Providing & fixing FINGER GRIP ANTISKID TILES size upto 600X600 over 12mm thick morter with proper joint filling with white cement and matching pigment complete in all respect
Providing & fixing on roof clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern and of approved make, colour & design on sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, complete, including providing skirting along the parapet walls as per drawing in the same manner complete in all respect as per E/I.
INTERNAL PLUMBING WORKS Suppling, fitting and fixing one piece water closet of white glazed vitreous chinaware of approved make and brand in position complete with necessary nut and boalts (Equivalent to Code No. 92084 ; Model Element of Hindware or equivalent.) Color Star white etc complete
Supplying, fitting & fixing CP Single Liver Basin mixture with 450mm long braided hose with pop up waste system . (Equivalent to Code No. F520012P of HINDWARE or similar brand).
Supplying, fitting & fixing CP 3 IN 1 Wall Mixture of Hindware (Catalogue No. F720022) or equivalent make .
Supplying, fitting and fixing toilet paper holder of approved make with fittings as necessary.
Supplying, fitting and fixing Tooth brush and Tumbler holder of Jaquar (ACN-CHR-1141N) or Equivalent.
Supplying, fitting and fixing Liquide Soap Dispenser of Jaquar (ACN-CHR-1135N) or Equivalent.
Supplying, fitting and fixing Soap Tray of Jaquar (ACN-CHR-1131N) or Equivalent.
Supplying, fitting and fixing 600mm long towel rack without lower hanger but with 3 hooks of Jaquar (CAN-CHR-1181FHN) or equivalent.
Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint. (Equivalent to Code No. 91207 ; Model Avior R of Hindware or equivalent.)
Supplying, fitting & fixing 190mm long 32mm dia Bottle trap of JAQUAR or similar brand).
Supplying, fitting and fixing 15 ltr. Horizontal Geyser complete with necessay fittings complete of approved make.
Suppling, fitting and fixing CP health faucet with 2 way bib cock of Jaquar or equivalent make
Supplying, comissioning of water purifier having RO+UV+UF+TDS control
Supplying, fitting and fixing 15 ltr. Horizontal Geyser complete with necessay fittings complete of approved make.
Supplying, fitting and fixing Steam Bath. Equivalent to Jaquar or equvalent
Supplying, fitting and fixing 1 user Souna Bath (Size : 900 x 1050 x 1900 mm) Equivalent to Jaquar or equvalent
Supplying, fitting and fixing Jacuzee Bath (Size - 1830 x 920 x 610mm) Equivalent to Romania or Equivalent
Supplying, fitting and fixing towel rail with two brackets. Equivalent to Code No. 1111BNM & Model - Jaquar
EXTERNAL PLUMBING Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only).
(i) 100 mm dia
(ii) 80 mm dia
(iii) 65 mm dia
(iv) 50 mm dia
(v) 40 mm dia
Supplying, fitting and fixing in position G.I. pipes of TATA make for underground works with all necessary accessories, specials viz.socket, bend, tee, union, cross, elbow, nipple, short piece etc.including cost of all materials,jointing materials ,cutting pipes,making threads,cutting trenches upto 1.5 metre below surface in all sorts of soil and refilling the same as directed with two coats of painting on G.I. pipes and specials with bituminous paint complete in all respect. (Payment will be made on the centre line measurement of the total pipe line including all specials No separate payment will be made for accessories, specials.Payment for painting will be made seperately)
(xi) 150 mm dia. medium quality
(ix) 100 mm dia. medium quality
(viii) 80 mm dia. medium quality
(vii) 65 mm dia. medium quality
(vi) 50 mm dia. medium quality
(v) 40 mm dia. medium quality
(iv) 32 mm dia. medium quality
(iii) 25 mm dia. medium quality
Supplying & laying Double Wall Corrugated (with external annular corrugation and smooth internal walls) High Density Polyethelene Pipes conforming to IS 16098 (Part-II):2013 having Stiffness Class of SN 8 with Ring Stiffness not less than 8.00 KN/Sqm. and Impact ResistanceTIR value not more than 10% including necessary jointing materials for non-pressure underground Drainage, Sewerage & Cross drainage application.
(i) 150mm internal dia.
(iii) 250mm internal dia.
(iv) 300mm internal dia.
(v) 400mm internal dia.
(vi) 500mm internal dia.
(vii) 600mm internal dia.
(viii) 800mm internal dia.
Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm (depth) with 250 mm thick 1st. class brick work in cement mortar (1:4) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (1:3:6) with stone chips over a layer of jhama brick flat soling,15 mm thick (1:4) cement plaster to inside walls and out-side walls upto G.L. and 20 mm.thick (1:4) plaster to bottom of the pit, providing necessary invert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (1:4) in all external surfaces of the slab and fixing R.C.P.C. manhole cover in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materials.
ii) With Bazree (N.B Varity)
iii) Extra for each additional depth of 150 mm or part thereof beyond initial 600 mm depth.
Supplying, fitting and fixing in position reinforced cement polymer concrete manhole /gully pit cover with matching frame.As per I.S-12592(M.D) (ii) 25 MT load bearing capacity round manhole cover provided with two lifter hooks fitted with matching frame of size
Cover: 680 mm X 90 mm Frame: 800 mm X 165 mm opening: 500mm Weight: 196 kg (approx) (vi) 5 MT load bearing capacity round manhole cover provided with two lifter hooks fitted with matching frame of size
Cover: 565 mm X 65 mm Frame: 665 mm X 125 mm opening: 470mm Weight: 90 kg (approx) Supplying, fitting and fixing in position FRP/GRP/ COMPOSITE UV stabilizer Gully Pit Cover with high abrasion surface of 7mm top thicknes, density of 2KG/m³ of approved make with rim of approved make (Heavy type) (ii) 20 M.T. Gully pit cover (yard gully) with arrangement for opening of size Frame Clear Opening 640 mm X 240 mm. Cover Out to Out 700 mm X 300 mm.
Supplying, comissioning of water treatment Plant having flow 50 cu. mtr. / hr. with MS vessals Plant Description : i) Oxidation Filter. (MSEP 1 no. 1200 Dia. X 1500 HOS) ii) Pressure Sand Filter (MSEP 1no 1800mm Dia. X 2400mm HOS). iii) Activated Filter (MSEP 1no 1800mm Dia. X 2400mm HOS). iv) Air blowers 2 Nos. (1w+1s) v)Filter feed Submersible Pump 2 No (1w+1s) vi) Hypo chlorine doing systems
Supplying, comissioning of 200 KLD moduler STP including all necessary Civil work, Plant Room and pipe work. Plant Description i) FRP Package Sewage treatment plant. (1 no.) ii) Sludge Recycle Pump (1 no). iii) Air blowers 2 Nos. (1w+1s) iv) FAB MEDIA (01 Lot ) v) Filter feed Submersible Pump 2 No (1w+1s) vi) Pressure Sand Filter (MSEP 1no 1800mm Dia. X 2400mm HOS). vii) Activated Filter (MSEP 1no 1800mm Dia. X 2400mm HOS). viii) Hypo chlorine doing systems
Supplying, fitting and fixing open well submersible pump including all necessary fittings (50 cu. mtr. /hr and 40 to 50 mtr head.) [Note: This work should not be executed without specific permission of Superintending Engineer.]
Supplying and fixing double door Vertical Out door type panel TPN MCB Distribution board for MCCB incomer with IP-65 protection, on angle iron frame on base & mending good the damages to original finish incl. (Inter connection with suitable size of copper wire and neutral link & provision for earthing attachatment.(canopy basaed)and suitable Buschamber. INCOMMING-4 Pole MCCB,With adjustable thermal setting 400 amp,35 KA.
Out going-63 A MCB FP-10 Nos,10A DP MCB-4 NOS With 3 Phase voltmeter,Ampmeter and indicating LED Lamp. Supplying and fixing double door Vertical Out door type panel TPN MCB Distribution board for MCCB incomer with IP-65 protection, on angle iron frame on base & mending good the damages to original finish incl. (Inter connection with suitable size of copper wire and neutral link & provision for earthing attachatment.(canopy basaed) Lighting system,Suitable bus chamber.
INCOMMING-4 Pole MCCB,With fixed thermal setting 25/100 amp,16 KA. Out going-40 A MCB FP-3Nos,32 A MCB FP-3 Nos ,DP MCB 10A-2 NOS With 3 Phase voltmeter,Ampmeter and indicating LED Lamp.As per Spec. 5 Kw dol stater 1 no for( single phase motor) cubical set MCB DITRIBUTION BOARD 3 Ph 4 Wire 415 V AC (20A-100A)With RS 485. Meter(Make-Secure,L&T,Schnider)
Wall bracket Fan with in built Regulator-Supply and Erection.
Wall mounted type LED 20 W-PHILIPS GRACE WALL LIGHT OR EQUIVALENT
suspended type high bay LED 70WATT (PHILIPS BY286V LED85S CW SK PSU or Equivalent)
1x20W Tube light LED (Philips TMC100 + 20W Essential LED Tube) or Equivalent
Mirror Light 9W-( Philips BN021C LED12S 6500 PSU GR or Equivalent)
Bulk head type LED (PHILIPS WT140W LED7S CW PSU)
Night Lamp Fittings
Light(Celling)-18W(Round) (PHILIPS SM251C LED20S- 6500 PSU WH OR EQUIVALENT)
Post Top 25W with Frame Sets 2.1 Mtr GI PIPE. (PHILIPS BGP300 LED28 740 PSU PC IN S1 OR EQUIVALENT)
Bolard with Frame Sets 0.9 Mtr (PHILIPS BCP151 LED150/WW PSU)
Celling Fan-1200mm ,5 star Rating
30 W Flood light For facad Perpose (IP-65) protection. (PHILIPS BVP131 OR EQUIVALENT)
Supply of 300 mm sweep, 900 rpm, 1 phase Exhaust fan of Havells make(Cat no.Turbo Force-SP or as per approved equivalent make list),(Brand approved by EIC) with heavy duty louvers shutter, complete with frame, as required complete.
PHILIPS 3D PRINTED LUMINAIRE WITH 40W LED LAMP OR EQUIVALENT
Fixing only louver shutter/cowl on wall with necy. bolts & nuts (6 mm dia x 62 mm long)
PANEL FOR 160 A MCCB 1 NO FOR INCOMMING, OUT GOING-40 A MCB 5 NOS, 32A MCB 2 ,25 A TPN MCB 3 . VOLT METER, AMMETER,AND INDICATING SIGNAL.
25 A TP MCB WITH BOX.(FOR VRF UNIT)
40 A TP MCB WITH BOX.(FOR AC UNIT Club House))
36 W CELLING TYPE LED FITTINGS (PHILIPS RC380B LED42S-6500 G5 L60W60 PSU OD OR EQUIVLENT)
150 W CELLING TYPE LED FITTINGS (PHILIPS BVP483 LED185 CW AWB PSU GR OR EQUIVALENT) Badminton
FALSE CELLING LIGHT 18 W ROUND (PHILIPS DN296B LED20S-6500 PSU WH OR EQUIVALENT)
Pnl for 250 A MCCB Incommer,Out going-63 A TPN MCB 5 Nos,32A TPN MCCB 5 NOS,10 A DP MCB 2 Nos with Ammeter,Voltmeter ,Indication Lamp with bus chamber.
LED FITTINGS 595X595 MM 29 W (RC380B LED 36S 6500 G5 L60W60 PSU Or Equivalent)
20 W SURFACE TYPE DECORATIVE FITTINGS (PHILIPS SP320P LED20S-6500 PSU DIA100 WH OR EQUIVALENT)
10 KVA single phase UPS with 30 min Backup
External Lighting Panel-IP65 (Out door Type) Canopy based.As per IEC Formet. Incommer-100A MCCB with day night timer based. Out going-TPN MCB 40A- 6 Nos, DP 10A-10 Nos,With Ammeter and Volt meter .Out going-TPN MCB 40- 4 Nos,With Ammeter and Volt meter .Indication Signal with LED indication Lamp.
External Lighting Panel-IP65 (Out door Type) Canopy based.As per IEC Formet.Incommer-100A MCCB with day night timer based.Out going-TPN MCB 63A- 2 Nos, DP 10A-10 Nos,With Ammeter and Volt meter .Out going-TPN MCB 40- 4 Nos,With Ammeter and Volt meter .Indication Signal with LED indication Lamp.
External Lighting Panel-IP65 (Out door Type) Canopy based.As per IEC Formet.Incommer-160A MCCB .Out going-TPN MCCB 100 A- 1Nos ,40 A TPN MCB-2 ,32A TPN MCB-4, DP 10A-6 Nos,With Ammeter and Volt meter ,Indication Signal with LED indication Lamp.For out side of Club-house and Aditorium.
Supply of 16M high mast shaft in two sections suitable for wind speed 47m/sec. with head frame, luminaries carriage suitable to install upto 12 nos. luminaries in symmetrical arrangement, lightning finial,along with Supply of Accessories required such as double drum winch, 6mm diameter SS wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box etc.
Supply of foundation bolts manufactured from special steel along with nuts, washers, anchor plates and templates.
Supply of Twin dome aviation obstruction light of TLL make APUS 3.0 LED type
Supply of outdoor stand mounted feeder pillar with 63A TPN MCB incomer, single dial timer, 45A contactor for the automatic switching of luminaries, power tool control with 2 no 9A contactors and raise lower push button, Incoming 35 sq. mm and out going 16 & 2.5 sq. mm terminals.
OCTAGONAL POLE Supply of 9M hot dip galvanised Conical pole with 70mm top dia., 178mm bottom dia. 3mm thick HT sheet, 275X275X16mm base plate along without Bracket.
Supply of 1500MM long standard single arm bracket madde up of 48.3mm dia GI pipe
Supply of 1500MM long standard double arm bracket madde up of 48.3mm dia GI pipe
Supply of M24X750mm long J type foundation bolts for 9M OP along with the required quantity of templates
Out door IP-65,type panel .Incommer-40A TPN MCB,Out going-10A DP MCB-30 Nos for sub panel of External lighting.
3CX4 Sq mm Cu Cable&Laying with existing way
150 W LED Fittings(BRP 340LED 175Cw)-140 W
200 W LED Fittings(BVP483 LED235 CW-195 W
Lightining Arrester
(4+18)6 Way TPN DB,IP-65/42 Protection with canopy ,with Isolator-32A-1 Nos and 6-10 A sp MCB 18 Nos
Boundary Light(BGP 300 LED 50 45 W)
150 KWP SOLAR SYSTEM ON GRID SPV PLANT 150 KWP(40000/KWP)
NET METERS 3 PHASE
ZERO EXPORT DEVICE 3 PHASE
SUBSTATION EQUIPMENTS Incommer 630 A MCCB, Microprocessor base with De-Tuned cuper reactor 14% APFC PNL 300 KVAR
Incommer 800 A ACB, Microprocessor base with De-Tuned cuper reactor 14% APFC PNL 425 KVAR
Acdb for Substation.
DCDB,Input-230 V ac and Output-24 V dc, with battery charger .Capacity 100 Amp/hr.Battery as per spec.
1600 KVA oil type 33/.415 KV DYN-11,OLTC Based out door type Transformer.
LT Panel for Substation.(Normal Supply)
Emergency Panel for Substation.
Load Management system with PLC Based ,Plc pnl,Total desk top set ,all type of cables and all acessaries for complete job.
AMF Features,with DG on when Gridis failure.
Supply of 3Cx240 sq mm 33 KV grade xlpe earthed Alluminium cable.
Supply of 3cx185 sq mm 33 KV grade xlpe earthed Alluminium cable.
Supplying, Installation, Testing and Commissioning of indoor type, floor mounted, metal clad, 33 KV, VCB panel with 4 Nos. VCBs, totally enclosed & fully interlocked, horizontal drawout, horizontal isolation type breaker as per IS 13118, as amended upto date and additional specifications, having capacities as mentioned below, single break, trip free mechanism, manually charged and auto / manually closing breaker suitable for use on 33 KV, 3 Phase, 50 Hz, A.C supply with short circuit fault level of 26.3KA, complete with self contained fully interlocked, rack in and rack out mechanism, air insulated but encapsulated copper bus bars of 800 Amps capacity, breaker featured with mechanical ON/ OFF indicator with hand trip device, spring release coil, shunt trip coil and auxiliary switch of 6 NO + 6 NC and equipped with following switchgears & accessories connections suitable for 3 Core "E" HT XLPE insulated, 33 KV cable (cable entry from bottom side), end termination with heat shrinkable jointing material etc as required. Breaker should be tested for M2, E2 & C2 with VI capable to take Shortcircuit current for 100 Nos Shots .
Inc-1 no 800 A VCB,and Oug-630A VCB for 1600 KVA Tr.PT should be used at Incomming site.Amp meter,Volt-meter used each sections.
Testing and comissoning of entire substation
450 mm exhaust Fan
Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42. For Terrace Pump
Supply and fixing of PVC sheathed following conductor 1.1 KV grade armoured Cable of following sizes including making end termination with compression gland & bimetalic lugs, and support etc.complete as required
10 × 2.5 sq.mm.(Copper)
Pressure Gauge Assemble with Gate/Ball Valve
Air release Valve / Drain Valve
MS Structure support for piping
Providing and fixing 25 mm nominal gun metal gate valve class I with CI wheel of approved quality with union (Screwed end)
Supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect.
Providing , fixing Dry Chemical Powder (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (4 Kg Capacity)
Carbon Di-oxide Type , Gas Confirming to IS ‘15222’ , Cylinder Confirming to ‘IS 7285’ & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ‘IS 15683’ & ‘IS 2878’ ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)55oC Suitable for ‘B’ ‘C’ Class of FIRE (4.5 Kg Capacity)
Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (5 Kg Capacity)
AC For 1.5ton capacity ,out door should be cuper coil. Operated gas R-22.MAKE-SUMSUNG,VOLTAS,CARIER.
AC For 2 ton capacity ,out door should be cuper coil. Operated gas R-22.MAKE-SUMSUNG,VOLTAS,CARIER.
Gyser 2000W For 5 Star Rating.MAKE-HAVELS,BAJAJ,KENSTAR
AC PIPE(Gass pipe+out side cable+drain pipe)
VRF OUTDOOR UNITS : Supply of Variable Refrigerant Flow / Volume Systems with Inverter Scroll Compressor suitable to operate 50-52deg C outside temp with R410A refrigerant, Aircooled Condenser along with Inbuilt Micro Processor panel, hydrophilic blue fins, refrigerant cooled heat sink and twin accumulator. The minimum COP of modules should be 5.5 at 50 % load at ARI Condition.
12 HP OUTDOOR UNIT
16 HP OUTDOOR UNIT
36 HP TOP DISCHARGE ODU
VRF INDOOR UNITS : Supply of Ductable Indoor units connected to the VRF system
4.0TR Ductable IDU
5.0TR Ductable IDU
8.0TR Ductable IDU
6.0TR Ductable IDU
Supply of Cassette Indoor units connected to the VRF system
3.2TR Cassette IDU
4.0TR Cassette IDU
Supply of Hi-wall Indoor units connected to the VRF system
1.7TR Hi-wall IDU
2.0TR Hi-wall IDU
2.5TR Hi-wall IDU
2.8TR Hi-wall IDU
Supply of Air Handling Unit Connected with Variable Refrigerant System :- Supply of Floor Mounted Air Handling unit with Thermal break profile .Blower shall be DIDW backward Curved blade belt driven. AHU shall be complete with Squirrel cage induction motor, 4Row DX Type cooling coil. Pre Filter section with filters of non woven synthetic media of supply as indicated below. 8000 CFM, 20TR Floor Mounted AHU,50mm ESP
ACCESSORIES : Supply of Indoor Refnet
Supply of Corded remote Controller
Supply of Cordless remote Controller
Supply of AHU Kit
Supply of Blue Star make 3 Star Rated Fixed Speed Hi-wall Split Air Conditioners for Server Room 2.0TR Hi-wall Split unit (1W + 1 S)
Erection, testing & commissioning of Air Cooled all Inverter Controlled Variable. Minimum capacities of each outdoor units are as follows
12 HP OUTDOOR UNIT
16 HP OUTDOOR UNIT
36 HP TOP DISCHARGE ODU
VRV/VRF Indoor units - Ductable type Ceiling Suspended Unit Ductable type Ceiling Suspended Unit - Erection, testing & commissioning of Ductable Type Indoor units
VRV/VRF Indoor units - Ductable type Ceiling Suspended Unit Ductable type Ceiling Suspended Unit - Erection, testing & commissioning of Ductable Type Indoor units
VRV/VRF Indoor units - Cassette type Indoor Unit
VRV/VRF Indoor units - Hi-wall type Indoor Unit
Non VRF Hi-wall Split unit
Installation of Indoor Refnet
First charge of Refrigerant
Floor Mounted AHU - Erection, testing & commissioning Indoor units
8000 CFM, 20TR Floor Mounted AHU
Installation of AHU Kit
Refrigerant piping Supply, installation, testing & commissioning of the insulated refrigerant piping between outdoor unit to indoor units as per the specifications. Refrigerant piping shall be made of hard drawn copper pipe(min 1mm thick) with one side expander factory fabricated suitable for variable refrigerant flow/volume system including all fittings, i.e. bends, elbows, tees with an internal joint type fitting etc.Bend/ Elbows shall also have one end expander. The insulation shall be of 13/ 19 mm thick Class-O Nitrile/ Polyethylene based insulating material through out the running length of refrigerant piping. The piping shall be laid in shaft/walls/roof/ceiling well supported at specific intervals with mettallic supports and screwed with anchor fasteners for the following sizes of refrigernat piping.
Supply & Fixing of Copper Refrigerant piping for Hi-wall Split unit
Communication cables Supply & Fixing of standard copper 2C x 0.75 sq.mm sheilded communication cabling to have interface between outdoor & Indoor units
Supply & Fixing of Cabling for Hi-wall Split unit
Drain Piping Design, supply, installation, testing & commissioning of drain piping consisting of hard PVC pipes of following sizes insulated with 9mm nitrile rubber with necessary accessories and adequate supports as per specifications.
32 mm dia.
25 mm dia.
Duct Supply, erection, testing & commissioning of Site Fabricated GSS ducting to be complete with elbows, slip-on flanges, turning vane, GI fully threaded rods, GI supports/hangers etc. & all accessories to complete the system as above standard.
24G GI Sheets
22G GI Sheets
20G GI Sheets
Insulation : Supplying and fixing of Thermal Insulation with 25 mm thick Class O Fire retardant, Closed Cell Nitrile Rubber insulation.
Supplying and fixing of Thermal Insulation with 19 mm thick Class O Fire retardant, Closed Cell Nitrile Rubber insulation.
Supplying & fixing of Acoustical insulation with 15 mm thick Open Cell Nitrile Rubber insulation.
Supplying & fixing of powder coated extruded aluminium section supply air grills with volume control dampers as requied.
Supplying & fixing of powder coated extruded aluminium section return air grills without volume control dampers as requied.
Supply and Fixing of GI duct dampers
Supply & Fixing of motorised fire damper
Motorised Fire damper
Actuator with Control Panel
Supply & Fixing of Canvas Connection
Supply & Fixing of MS Structure for placement of VRF Outdoor unit
Supply & Fixing of 50mm thick TF Quality Underdeck Insulation complete with Bituminous coat and fixing arrangement.
Supply & Fixing of Ready made Bracket for Hi-wall Split unit
Fresh air arrangement with Bird Screen, Cowl, Damper
Providing, laying and making kerb channel 30 cm wide and 50 mm thick with cement concrete M 25 over 75mm bed of PCC (1:3:6), including finishing the top smooth etc. complete and as per direction of Engineer-in-charge.
Providing and laying 80mm thick reinforce factory made cement concrete interlocking 80mm thick Grass paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of compacted earth all complete as per the direction of Engineer-in-charge.
Filling in foundation treanchs and plinth In layer not exceeding 150mm. Thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50m. And lift of 1.5m. All complete as per building specification and direction of E/I ( mode of measurment compacted volume)
Lead of Earth ( upto 3 km.)
Laying, spreading and compacting Moorum of specified grade as filler for WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, watering and compacting to the required density .
PARK & PLAY GROUND EQUIPMENT:- (ALL PRODUCTS SAMPLE SHOULD BE APPROVED BEFORE PURCHASE) Supplying, stacking and installing 3 seater cast Iron & WPC combo bench of approved make & design as per direction of Engineer in charge.
Supplying, stacking and installing PVC Garbage bins of approved make & product as per direction of Engineer in charge.
Supplying, stacking and installing PVC make carton type Garbage bins of approved make & design as per direction of Engineer in charge
Construction of central Garbage bins (4mX2.5mX2.1m) with MS net cover complete as drawing & specifications as per direction of Engineer in charge
Supplying, stacking and installing MS Swing with hanging chain system for two seater of approved make & design as per direction of Engineer in charge
Supplying, stacking and installing Curve/Semi circular type FRP Sliding with MS Support stand of approved make & design as per direction of Engineer in charge
Supplying, stacking and installing Sea Saw FRP Seating with MS Support stand of approved make & design as per direction of Engineer in charge
Supplying, stacking and installing Bridge Ladder with necessary fittings fixtures & support of approved make & design as per direction of Engineer in charge
Supplying, stacking and installing Rotating Platform with necessary fittings fixtures of approved make & design as per direction of Engineer in charge
For Play Ground:-Designing , Providing & Fixing Goalpost complete set made of GI & neat fixing arrangement as per rules & regulations of sports authority. Complete in all respect with necessary foundation work & painting finishing as per satisfaction of Engineer in charge.
For Lawn Tennis Court:-Designing , Providing & Fixing Netfixing pole set made of GI , neat fixing arrangement & Judge seating arrangment as per rules & regulations of sports authority. Complete in all respect with necessary foundation & painting/ finishing work as per satisfaction of Engineer in charge.
Football Ground & Lawn Tennis Court Line Marking with paint of approved manufacturer with necessary equipments as per rules & Supply of Neat as per rules & regulations of sports authority. Complete in all respect as per satisfaction of Engineer in charge.
Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-incharge.(Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment).Overhead informatory road signage
Design, fabricate, supplying & fixing Customized name plate (16''x10'') using the best of wooden and acrylic. White acrylic fonts shining beautifully on dark wooden textured MDF base. Eye-pleasing rectangular geometry. Comes with wall hanging hook on the back complete in all respect as per direction of Engineer in charge.
Designing , Manufacturing, supplying and fixing in position as per drawing, 3D Acrylic Letter Signage in english & Hindi. Size of Letter Height Minimum 300mm with proportionate width including necessary lighting complete in all respect.
Design, Fabricate ,Supplying & Fixing of PHOTOLUMINESCENT Signage Autoglow of approved make at any floor at any height, made of Rigid sheet,ARS 10000,1mm Thk, with approved Size of Lettering (Hindi & English ), Colour, Base Colour & Image with necessary hanging arrangement from celing/ Fixing on wall or Door etc complete in all respect.
Size -400X150
Size - 500X200
Size - 400X1200
Supply of NON PHOTOLUMINESCENT Signage Non Autoglow of approved make at any floor at any height,made of Stainless Steel with approved size of Lettering (Hindi & English ), colour,Base Colour & Image with necessary hanging arrangement from celing/ Fixing on wall or Door etc complete in all respect. Size: 200x150
Supply & Fixing EMERGENCY LIGHT with LED Light Signage with battery back up (BEAM- Double-2 X 12 Watt LED Beams + 4 Watt Display. Powder Coated , heavy duty Steel Sheet made Body. Minimum Dimension:13" X 5" X 13". Charging voltage-230VAC, Battery included. 5- 6 Hours backup. Fully Automatic; i.e, automatic on in case of Input Power Failure & automatic off as Power resumes.) of approved make at any floor at any height,fixing with made of Aluminium frame with approved size of lettering, Colour, Base Colour & Image,necessary fixing arrangement complete in all respect as per direction of Engineer In Change.
Furniture & Kitchen Appliances GENERAL NOTES:- 1.The unit price includes supplying, transporting , loading & unloading with safety measure, workmanship for customized portion, storing and installation as per drawing with the full satisfaction of Engineer in charge/Architect. 2.The contractor has to take approval from Engineer in charge/Architect for raw materials for the each item (Plywood, Teak wood, Veneer, Laminates, polishing, painting, textiles, locks, brace hinges, stainless steel grade 304, foam 32kg/m3, and any accessories) required before manufacturing. 3.The contractor has to produce sample with specification as per approved make & taking approval from Engineer in charge/Architect before purchase . 4.No damaged furniture will be allowed during handling. 5.All furniture works includes preparation, painting with high grade furniture paints. 6.Contractors should follow relevant specification before quote. 7. Furniture FROM ISO 9001:2015, ISO 14001, CERTIFIED MANUFACTURERS
Auditorium Chair. The seat should be made of Polyurethane Foam moulded with 1.5 ±0.1cm. thk. plywood insert arid upholstered with fabric. * Approx. Seat Size: Depth: 42.0cm. Width @ rear: 44.0cm. Width @ front: 41.0cm. The back assembly should be flexing type and made of Polyurethane Foam moulded with MS. tubular frame insert and upholstered with fabric and back cover. The insert should be made of 01.9 ±0.02cm x 0.16 ±0.0.128cm. thk.MS tubular frame with flexible nylon straps running across the length and width of the frame. * Approx. Back Size: Height: 65.5cm. Width @ top: 34.5cm. Width @ seat level: 46.0cm. The foam shall be HR polyurethane foam & shall be moulded with density = 45 +1-2 kg/m3. . OLYURETHANE FOAM: The Polyurethane foam should be moulded with density = 45 ±2 kglcu.m . COVERS: The back cover and mechanism cover should be vacuum formed from black ABS sheets. The Armrest understructure shall be upholstered PU foam moulded with MS insert. Arm tops shall be made of black Integral Skin polyurethane with 50-70 Shore 'A' Hardness & reinforced with wooden insert. Armrest width = 7.0 ±0.5cm and shall be offered as common/individual armrest between chairs. The understructure shall be MS black powder coated ( DFT 40-60 microns ) understructure with integrated, auto tip-up mechanism which folds the seat when not in use. Footprint shall be a of base plate: made of HR steel 15.0 ±0.2cm X 22.0 ±0.2cm X 0.5 ± 0.05 cm thick. Backrest supporting beam width shall be 46.0 ±0.2cm.(L) x 8.0 ±0.03cm. x 4.0 ±0.03cm. x 0.2 ±00.16cm MS tube. Understructure shall be fixed to ground by anchors with washer and nut. FLOORING PRE - REQUISITE shall be ITE : The auditorium chair shall be designed to get mounted/grouted on floors with flooring specification .
Auditorium Green Room Chair. The cushioned seat assembly shall consist of seat base moulded in glass-filled Poly-amide, moulded Polyurethane foam & upholstered with high stretch knitted polyester fabric. The cushioned back assembly shall consist of back inner moulded in Polypropylene in-situ moulded with Polyurethane foam & upholstered with high stretch knitted polyester fabric. Back Size : 45.5 cm. (/1/) x 53.0 cm. (H) Seat Size : 48.5 cm. (W) x 47.0 cm. (D) .The HR polyurethane foam shall be used in seat and back cushion shall be moulded in Density Min 48 kg/m3, and hardness load 15 ± 2 kgf as per IS:7888 for 25% compression. The seat and back shall be firmly connected to the base frame and shall be cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjustments. The seats shall offer impact cushioning while sitting and synchronise with the back movement during posture changes. The spine shall be "S" shaped & moulded in high strength glass-filled Poly-amide and the spine connector shall be moulded in glass-filled Poly-amide & shall form the back-spine structure involved in multi-dimensional recline motion. The variable tilt angle recline motion shall be adjusted with 3 position Tilt Limit feature which shall be inbuilt in seat base and the tension (return force) shall be user weight dependent. The assembly shall consist of armrest housing sliding over the armrest structure, both moulded in glass-filled Poly-amide: The height adjustment feature shall be button operated having adjustment of 6.6±0.5cm. The Armrest Top shall be made up of integral skin PU moulded over plastic inner moulded in glass-filled Poly-amide. The seating height shall be adjusted with a pneumatic gas-lift having an adjustment stroke of 9.2 ± 0.3 cm. The pedestal shall be injection moulded in glass-filled Poly-amide and fitted with 5 nos. twin wheel castors. The pedestal shall be 66.0±0.5 cm. pitch centre diameter and 76.0±1.0 cm. with castors 5 nos. twin wheel castos shall be injection moulded in Poly-amide having 5.0 ± 0.1 cm wheel diameter assembled to the pedestal.
Design & provide custom made Storage Drawer with drawers at below Granite Slab (1800mmX450mmX750mm) with 30mm thick green ply finished with Laminate. Necessary 2nd class Teakwood frame with paint finish of required section to be used complete in all respect as per approved Shop Drawing & full satisfaction of Engineer in charge.
Providing and fixing mirror of superior Mirror glass of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape
4Door PLU with Locker . Overall size of 2 - Door PLU + Lkr (Base) shall be 380mm(W)x450mm(D)x1830mm(H). R1 - 4 Sheets(Cam Lock). Stackability shall have add-on units that shall be stacked width wise to form bank of lockers having common side panel. Locking shall have 10 Lever cam lock with lock lever. Material shall be CRCA 0.6 mm thickness. Construction shall be Rigid Knockdown construction , shelf shall be uniformly distributed load capacity per each shelf level shall be 35 Kg maximum . Finish shall be epoxy polyester powder coated to the thickness of 50 microns . Handle/Label holder shall be Aesthetically appealing Snap fit ABS plastic handle . Ventilation shall be attractive punched pattern for ventilation . 1 Hanging rod in both compartment .
FOR CLUB HOUSE:- Wooden Single size Bed . Solidwood Single Bed is made of kiln-dried and chemically treated solid wood and features an elegant headboard that is 50 mm thick. Additionally, it has a footboard thickness of 50 mm, and the side rails are 450 mm from the floor. The panels are strong and sturdy, made of continuous plywood, and the bed also has a storage box underneath.
Side Unit :-Dimensions : 32 x 30 x 59 cm; 8 Kilograms 1 x Wooden 3 Drawer Bedside Table Bedroom Storage Cabinet, Material: MDF Wood & necessary hardware
1 SEATER SOFA :-Overall Size : Width : 115.5cm Depth : 94.5cm Height : 85cm Seating Height : 33.5cmSTITCHING:THREAD:Pole Poroli , PVC:PVC Gray ,FRAME MATERIAL:Pine Wood & Ply Wood SEAT FOAM:30kg/m3 /32d BACK FOAM:Polyester Stapple Fibre
2 SEATER SOFA :-Overall Size : Width : 115.5cm Depth : 94.5cm Height : 85cm Seating Height : 33.5cmSTITCHING:THREAD:Pole Poroli , PVC:PVC Gray ,FRAME MATERIAL:Pine Wood & Ply Wood SEAT FOAM:30kg/m3 /32d BACK FOAM:Polyester Stapple Fibre
CENTRE TABLE:-Overall Size :Width : 110cm Depth : 60cm Height : 50cmTABLE LEGS METERIALS & SIZE : OVAL METAL TUBE ,THICK 1.5 mm , Color : SILVER POWER COATING . TABLE TOP MATERIALS & SIZE : (DENSITY / TYPE):L X W X T:1100 X 600 X 8 MM , Color : PARTIAL BLACK TEMERED GLASS TOP FULL BLACK TEMPERED GLASS . TABLE BOTTOM MATERIALS & SIZE : (DENSITY / TYPE) : L X W X T:1100 X 600 X 6 MM , Color :FULL BLACK TEMPERED GLASS
READING TABLE-1:-Overall Size1200x450 Material: Hardware. Body panels are made of 18 mm thick Prelaminated Particle Board All the exposed edges are edge banded with 2 mm thick PVC edge banding. Door / drawer front are 18 mm thick made of 18 mm P.V.0 membrane pressed MDF. Drawer components are made of 18 mm thick Prelaminated Particle Board .All the exposed edges are edge banded with 2 mm thick PVC edge banding. Drawer bottom are made of 9 mm thick Prelaminated particle board.The high quality hardware used like Satin finish Handles of make SWASTIK, Slide Roller, rastex 15, wooden dowels is of make Hettich..Construction :Knock Down construction.Packets :3 packet.Finish :.PVC membrane pressed MDF is in Wenge Realistic Pore Shade for Dark Chocolate Vermount V 45309.18 mm thick Prelaminated Particle Board is in Colarain Shade for Dark Chocolate.
READING TABLE-2:-Overall Size including top cornice :900X450 Material: Hardware. Body panels are made of 18 mm thick Prelaminated Particle Board All the exposed edges are edge banded with 2 mm thick PVC edge banding. Door / drawer front are 18 mm thick made of 18 mm P.V.0 membrane pressed MDF. Drawer components are made of 18 mm thick Prelaminated Particle Board .All the exposed edges are edge banded with 2 mm thick PVC edge banding. Drawer bottom are made of 9 mm thick Prelaminated particle board.The high quality hardware used like Satin finish Handles of make SWASTIK, Slide Roller, rastex 15, wooden dowels is of make Hettich..Construction :Knock Down construction.Packets :3 packet.Finish :.PVC membrane pressed MDF is in Wenge Realistic Pore Shade for Dark Chocolate Vermount V 45309.18 mm thick Prelaminated Particle Board is in Colarain Shade for Dark Chocolate.
CHAIR FOR READING TABLE:-The cushioned seat assembly shall consist of seat base moulded in glass-filled Poly-amide, moulded Polyurethane foam & upholstered with high stretch knitted polyester fabric. The cushioned back assembly shall consist of back inner moulded in Polypropylene in-situ moulded with Polyurethane foam & upholstered with high stretch knitted polyester fabric. Back Size : 45.5 cm. (/1/) x 53.0 cm. (H) Seat Size : 48.5 cm. (W) x 47.0 cm. (D) The HR polyurethane foam shall be used in seat and back cushion shall be moulded in Density Min 48 kg/m3, and hardness load 15 ± 2 kgf as per IS:7888 for 25% compression. The seat and back shall be firmly connected to the base frame and shall be cantilevered in such a way that it gives a multidimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjustments. The seats shall offer impact cushioning while sitting and synchronise with the back movement during posture changes. The spine shall be "S" shaped & moulded in high strength glass-filled Poly-amide and the spine connector shall be moulded in glass-filled Poly-amide & shall form the back-spine structure involved in multi-dimensional recline motion. The variable tilt angle recline motion shall be adjusted with 3 position Tilt Limit feature which shall be inbuilt in seat base and the tension (return force) shall be user weight dependent. The assembly shall consist of armrest housing sliding over the armrest structure, both moulded in glass-filled Poly-amide: The height adjustment feature shall be button operated having adjustment of 6.6±0.5cm. The Armrest Top shall be made up of integral skin PU moulded over plastic inner moulded in glassfilled Poly-amide. The seating height shall be adjusted with a pneumatic gas-lift having an adjustment stroke of 9.2 ± 0.3 cm. The pedestal shall be injection moulded in glass-filled Poly-amide and fitted with 5 nos. twin wheel castors. The pedestal shall be 66.0±0.5 cm. pitch centre diameter and 76.0±1.0 cm. with castors 5 nos. twin wheel castos shall be injection moulded in Poly-amide having 5.0 ± 0.1 cm wheel diamter assembled to the pedestal.
TV TABLE:-Overall Size including top cornice: Width - 1150.0 mm Depth - 473 mm Height - 830 mm.MATERIAL:Body panels are made of 18 mm thick Prelaminated Particle Board All the exposed edges are edge banded with 2 mm thick PVC edge banding. Door are 18 mm thick made of 18 mm P.V.C membrane pressed MDF.Drawer components are made of 18 mm thick Prelaminated Particle Board .All the exposed edges are edge banded with 2 mm thick PVC edge banding. HARDWARE:The high quality hardware used like Satin finish Handles of make SWASTIK, Door Hinge Slide- On 2333, rastex 15, wooden dowels is of make Hettich..CONSTRUCTION:Knock Down construction. PACKETS:3 packet.FINISH: PVC membrane pressed MDF is in Wenge Realistic Pore Shade for Dark Chocolate Vermount V 45309.18 mm thick Prelaminated Particle Board is in Colarain Shade for Dark Chocolate.
LUGGAGE RACK:-Overall Size 1200X600 provide custom-made , finishing & fixing in position customised Luggage Rack made 30mm thick green ply finished with Laminate. Necessary 2nd class Teakwood frame with paint finish of required section to be used complete in all respect as per approved Shop Drawing & full satisfaction of Engineer in charge.
WARDROP:-Overall Size 1500X600 provide custom-made , finishing & fixing in position customised Luggage Rack made 30mm thick green ply finished with Laminate. Necessary 2nd class Teakwood frame with paint finish of required section to be used complete in all respect as per approved Shop Drawing & full satisfaction of Engineer in charge.
CHAIR:-Overall Size : Length : 55cm Width : 57.5cm Height : 77cm Seating Height : 46cm Back & Seat Material :Light Brown Fabric (300 GSM) •Seat- 60 mm foam (24.5D) •Back- 45mm foam (24.5D) Leg Material Metal -Black powder-coated
SOFA-3:-Overall Size : Width : 218cm Depth : 94.5cm Height : 85cm Seating Height : 33.5cmSTITCHING:THREAD:Pole Poroli , PVC:PVC Gray MATERIAL:Pine Wood & Ply Wood SEAT FOAM:30kg/m3 /32d BACK FOAM:Polyester Stapple Fibre
Centre Table for Ladies Room:-Overall Size :Width : 60cm Depth : 60cm Height : 45cmTABLE LEGS METERIALS & SIZE : OVAL METAL TUBE ,THICK 1.5 mm , Color : SILVER POWER COATING . TABLE TOP MATERIALS & SIZE : (DENSITY / TYPE):L X W X T:600 X 600 X 8 MM , Color : PARTIAL BLACK TEMERED GLASS TOP FULL BLACK TEMPERED GLASS . TABLE BOTTOM MATERIALS & SIZE : (DENSITY / TYPE) : L X W X T:500 X 500 X 6 MM , Color :FULL BLACK TEMPERED GLASS
Metal Steel Office Almirah. Almirah shall have an overall size of 916mm(W)x486mm(D)x1980mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. Have a handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveler with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10).
TABLE WITH ERU. Table size shall be 1500 Width mm x 750 Depth mm x 740 Height mm .Table top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick backing laminate (bdl) .Edge shall be Flat & Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge shall be Sealed with 2 mm thick PVC beading. The return unit size shall be 1050 Width x 450 Depth x 705 Height. The top of return unit shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL). Edge shall be flat & duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge shall be sealed with 2 mm thick PVC Beading.
Cafeteria ROUND TABLE . Worktop shall be made of 25mm MDF OSR with pu matt finish on top side. Hardness on top surface is 2H. The under-structure shall consist of an Innertube Assembly with Top Plate, for Worktop Mounting, & an Outer Tube Assembly with Round Plate. The Inner & Outer Tube Assemblies shall be telescopically connected. The Top Plate shall be made of 5mm thk HOT ROLLED Steel Plates (HR) (As per IS:2062) & the bottom plate shall be made of 8mm thk HOT ROLLED Steel Plates (HR) (As per IS:2062). The Inner Tube Assembly shall be made of 082.5 x 2thk ROUND ELECTRIC RESISTANCE WELDED Tubes (ERW)(As per IS:7138) and 8mm thk HOT ROLLED Steel Plates (HR) (As per IS:2062) welded together using TUNGSTEN INERT GAS Welding. The Outer Tube Assembly shall be made of 089 x 2.5 thk and ROUND ELECTRIC RESISTANCE WELDED Tubes (ERW)(As per IS:7138) and 8mm thk HOT ROLLED Steel Plates (HR) (As per IS:2062) welded together using TUNGSTEN INERT GAS Welding. The whole structure shall be EPOXY POLYESTER Powder Coated (DFT 40-60 microns). The product shall have knock-down construction. It shall be assembled using alloy steel hardware (blackened & coated with rust preventive oil).
Cafeteria UNWIND CHAIR .The Seat and Back should be made up of injection moulded indoor grade Polypropylene compound with SEAT SIZE : 52.5 cm. (W) x 53.2 cm. (D) & BACK SIZE : 51.6 cm. (W) x 40.5 cm. (H). The powder coated ( DFT 50±10 microns ) welded tubular frame should be made from 0 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.16 ± 0.0128 cm MSERW tube. The shoes should be made of indoor grade Polypropylene compound and snap fitted with tubular frame.
Hand rest Leatherette Bar stool of SS frame low back Height x Width: 939.8 mm x 406.4 mm with adjustable height
Designing , provide custom-made , finishing & fixing in position customised Bar counter Table & surrounding (50sqm) with under cabinet , wall cabinet (40sqm) & ceiling decoration (20sqm) made 30mm thick green ply finished with Laminate. Necessary 2nd class Teakwood frame with paint finish of required section to be used complete in all respect as per approved Shop Drawing & full satisfaction of Engineer in charge.
Designing , provide custom-made , finishing & fixing in position customised wooden cabinet 1500mmx450mm made 30mm thick green ply finished with Laminate. Necessary 2nd class Teakwood frame with paint finish of required section to be used complete in all respect as per approved Shop Drawing & full satisfaction of Engineer in charge.
Designing , provide custom-made , finishing & fixing in position customised modular Kitchen made 30mm thick green ply finished with Laminate. Necessary 2nd class Teakwood frame with paint finish of required section to be used complete in all respect as per approved Shop Drawing & full satisfaction of Engineer in charge.
Providing & fixing necessary Kitchen appliances as required of approved make & best model complete in all respect as per Engineer in Charge.
4Door PLU with Locker . Overall size of 4 - Door PLU + Lkr (Base) shall be 380mm(W)x450mm(D)x1830mm(H), R1 - 4 Sheets(Cam Lock). Stackability shall have add-on units that can be stacked width wise to form bank of lockers having common side panel. Locking shall have 10 Lever cam lock with lock lever plus option of hasp arrangement . Material shall be CRCA 0.6 mm thickness . Construction shall be Rigid Knockdown construction , shelf shall be uniformly distributed load capacity per each shelf level is 35 Kg maximum . Finish shall be epoxy polyester powder coated to the thickness of 50 microns . Handle/Label holder shall be Aesthetically appealing Snap fit ABS plastic handle . Ventilation shall be attractive punched pattern for ventilation .
FOR SWIMMING POOL With Arm Plastic Chair 62 x 59 x 87 cm; 2 Kilograms Weight
FOR BARRACK Single Cot Steel Bed Overall Size : Width : 208cm Depth : 92.5cm Bed Height : 38.5cm Bed with Headboard Height : 84cm. Color : Black . bed -metal frame materials & dimensions:(gauge +/- 0.1mm)m.s. pipe 25.4x 50.8 x 1.2 thk.;m.s. pipe 19.05x 19.05 x 0.8 thk.;m.s.angle 20x20x1.6 thk;m.s. pipe dia. 50.8 x 0.9 thk.;m.s. pipe dia. 15.875 x 0.8 thk.
One Single Size 100 mm thick foam mattress 180cmx90cm covered with cotton cloths
One Head Cotton Pillow 61 cms X 41 cms,Filling: 500gms Seedless Pure Semal Cotton,Outer Fabric: Pure Cotton Handloom.
One Pillow Cover 70 cm L x 45 cm W pure cotton
One bed Sheet Material cotton, thread count 150 Flat (L x W): 224 cm x 147 cm
Canteen Table with fixed Seating arrangement FROM ISO 9001:2015, ISO 14001, OHSAS 18000, SPECIFICATION. Top shall be stainless steel (SS-304) brushed finish 1.0mm thick with PLB insert of 18mm thick for durability, easy to clean & maintain hygiene. Understructure shall be made from square 40.0 X 1.6 mm thk MS tube ( IS:7138 ) which shall be welded to the top plate which shall be made of MS 5mm thk (IS:513). Top plates shall be fixed to Table top with screws. Cross members shall be square 25.4 X 1.2 thk MS tube (IS:7138). Seat shall be SS 304 thali 300 mm dia X 1.0 mm thk. Bottom ends shall be closed with Plastic buffers to prevent direct contact with floor and to avoid scratching with floor.
Storage Almirah. Overall Dimensions shall be 800(W)x500mm(D)x2100mm(H) . The construction shall be aesthetically appealing completely knock down construction . Legs shall be fitted with screw type leveler and material shall be from combination of CRCA 0.5 mm & 0.8 mm . The shelving shall be height wise adjustable shelf mounting , each full shelf shall have a load capacity of 40 kg UDL max. and 4 nos. of full adjustable shelves . Finish shall be epoxy powder coated to the thickness of 50 microns.
TV.:- Providing & Fixing 108cm(43inch) Full HD LED TV complete in all respect as per Engineer incharge.
Supply, fitting & finish of Indoor Badminton synthetic court 5.0mm thick maintaining all rules & regulations of Badminton world federation. The floor junction will be welded with same color welding cod & marking the Playing game line with white colour complete in all respect as per instruction of Engineer in charge.(Color: Green, Pattern Sand, Dimension of roll: 1.8mtx15mtx4 roll .Laying with both side adhesive tape having minimum warranty period of 5 years from wear & tear.)
Providing & fixing Table Tennis board maintaining concerned sports rules & regulations complete in all respect as per instruction of Engineer in charge.
Providing & fixing Billiard board maintaining concerned sports rules & regulations complete in all respect as per instruction of Engineer in charge.
Supply , fitting & finishing 10mm thick EPDM Gymnasium Rubber flooring interlocking tiles complete in all respect as per instruction of Engineer in charge.
Supply, fittings & fixing Gymnasium Equipments complete in all respect as per instruction of Engineer in charge.
Supply, fittings & fixing movable Badminton net fixing pole & Net with Pully & Wheel complete in all respect as per instruction of Engineer in charge..(Pole made of 38x38 mm square pipe base pipe 2 inch square pipe . Each side weight 20 kg , adjustable rachid with net fine quality spray PU paint )
Supply & preserve in position Badminton Racket
Supply & preserve in position Badminton Nylon Shuttle Cock(Set of 12 nos.)
Supply & preserve in position 2 nos. Table Tennis Racquet, 3nos. Ball & one adjustable Net.
Supply & preserve in position 2 nos. Billiard wooden Stick
Supply & preserve in position Billiard Multicolor Ball Set (16 nos. Ball)
Supply & preserve in position Matress(Measures 182.88 X76.2 X 0.76 cm (LxWxH); weighs 3.26 Kilograms made of high-density PVC;) for Yoga/ Meditation
ELECTROMECHANICAL WORK 10 Hp Single Phase Open Submersible pump , Make : Kirloskar
Outdoor Control Panel
16’ Dia GI Ring with 75 nos.Nozzles (Make:RES)
8’ Dia GI Ring with 48 nos.Nozzles (Make:RES)
1 inch Centre Jet Brass Nozzle with Ball Joint (Make:RES)
RES IP68 12V,10W Aluminium LED Underwater Light
SMPS & Controller ( Make: RES)
Interconnecting Pipe & Pipe Fittings with Control Valves
2.5 Sq.mm 3 core Cable & 1 Sq.mm 4 core Flat Cable
Ring & Light Stands along with stand and other fittings
Installation & Commissioning
Auditorium Sound System For Left/Right/Centre - SITC of 2-way compact speaker system, Low frequency: 13 cm (5.5") cone-type × 8, High frequency: Wave front control horn with compression driver x 4, Rated Impedance 8 Ω, Sensitivity (1 W, 1 m) 100 dB (1 W, 1 m), Frequency Response 75 Hz - 20 kHz, Directivity Angle Horizontal: 100゜, Vertical:Depending on directivity angle mode between drivers. Approved Makes ( RD, D & B, TOA)
SITC of 2*18" N-Dym Subwoofer @ 2000 wrms, Frequency Response (+/-3dB): 38Hz-1.5kHz, Sensitivity (@1w/1m): 125dB SPL, Nominal Impedance: 4 Ω, Power Handling (RMS): 2000 watts, Transducer 2×18″ Neodymium, 18mm Birch Plywood, SPEAKON NL4MP, Dimensions mm (HxWxD): 609 x 1194 x 952, Weight (kg): 110- Approved Makes ( RD, D & B, TOA)
SITC of 2 way fullrange speaker, Frequency Response (+/-3dB) 50Hz-19kHz, Horizontal Coverage Angle 70°, Vertical Coverage Angle 30°, Sensitivity (@1w/1m) 90dB SPL, Nominal Impedance 8 Ω, Power Handling (RMS) 300 watts, Transducer 1x1" HF exit, 1x10" Mid-Bass, Cabinet 12mm birch plywood, SPEAKON NL4MP - Approved Makes ( RD, D & B, TOA)
SITC of 2-way fullrange Monitor speaker, Frequency Response (+/-3dB) 60Hz-20KHz, Horizontal Coverage Angle Conical 80° (-6dB), Vertical Coverage Angle Conical 80° (-6dB), Sensitivity (@1w/1m) 98dB SPL, Nominal Impedance 8 Ω, Power Handling (RMS) 400 watts, Transducer Neodymium Coaxial: 1x1.7" HF exit, 1x12" Mid-Bass, SPEAKON NL4MP 1x1.7" HF exit, 1x12" Mid-Bass @ 400 wrms @ 8 Ω - Approved Makes ( RD, D & B, TOA)
SITC of Speaker rigging frame- Approved Makes ( RD, D & B, TOA)
SITC of Speaker Connection Bracket- Approved Makes ( RD, D & B, TOA)
SITC of Manual chain Hoist for load 100Kg - 2 poin hang for each array frame
SITC of 2 Channel Class D Amplifier 100-240 V AC, 50/60 Hz, Output SPEAKON connector, Output 2 channels : 700Wx2 (8Ω), , 1250Wx2 (4Ω), Frequency Response 20Hz- 20kHz (+/-3dB), Total Harmonic Distortion: ≤0.15%, S/N rate: ≥100dB- Approved Makes ( RD, D & B, TOA)
SITC of 4 Channel Amp, Power output @ 4 Ω (all channels driven) 4ch x 2250 watts, Power output @ 4 Ω (Bridge, Mono) 2ch x 5000 watts, Frequency Response: 20Hz-25kHz (+/-0.5dB), Total Harmonic Distortion (THD) 0.1% Damping Factor >500, Signal-to-Noise Ratio (SNR) 110dB, Power Supply: 220V AC- Approved Makes ( RD, Powersoft, TOA)
SITC of Mixing channels 32 Line Inputs (24 mono and 4 stereo) ; GROUP 4 GROUP Buses + ST Bus ; AUX 6 AUX Sends + 2 FX Sends ; MATRIX 1 Matrix out ; On-board processors FX1:REV-X(8 PROGRAM, PARAMETER control)/ FX2:SPX(16 PROGRAM, PARAMETER control)- Approved makes (Midas, Allen & Heath, Yamaha)
SITC of 4 In 8 Out DSP, 96KHz sampling frequency, 32-bit DSP processor, 24-bit A/D and D/A conversion; 4 inputs 8 outputs , PC control software to control, 2×24 LCD blue backlight display function settings, 6 LED display input/output, Each input and output has 6 independent parameter equilibrium, adjusting gain range up to ±20dB, while the input, output channel equalization can also choose Lo-shelf and Hi-shelf mode; control via the USB interface or RS485 interface, Each Input with two dynamic equalization adjustments - Approved makes (DB-Mark, Biamp, Symetrix)
SITC of wireless handheld microphone with (UHF)receiver ,12 Channel Preset or better , Display on Transmitter and Receiver , RF Power output 50mW or Better , Polar Pattern :- Cardioid , Carrier frequency range 500Mhz to 865Mhz , Frequency response 20Hz to 20Khz , Mute Button on Transmitter , Battery Operation time Minimum 8hr , Should have Charging Contact in Transmitter , Receiver dynamic range 80 dB (A-weighted) Or better , switching bandwidth Minimum 30 Mhz Or better Approved Make- Clock Audio/Rode/Beyerdynamic
SITC of Wired Vocal Microphone , Transducer type Dynamic Polar pattern Super cardioid Frequency response: 30 - 18,000 Hz Nominal impedance 600 Ω Connection 3-pin XLR male Approved Make- Clock Audio/Rode/Beyerdynamic
SITC of wireless Headworn microphone with (UHF) receiver ,12 Channel Present or better , Display on Transmitter and Receiver , RF Power output 50mW or Better , Polar Pattern :- Omnidirectional, Carrier frequency range 500Mhz to 865Mhz , Frequency response 20Hz to 20Khz , Mute Button on Transmitter , Battery Operation time Minimum 8hr , Should have Charging Contact in Transmitter .Receiver dynamic range 80 dB (A- weighted) Or better, switching bandwidth Minimum 30mHz Mhz Or better. Approved Make- Clock Audio/Rode/Beyerdynamic
SITC of Gooseneck Microphone( for Podium) Length of Gooseneck Mic 450mm to 500mm dual band Stem (Top and Bottom) Transducer type Condenser ,Polar pattern Cardioid or better Frequency response 70 – 16,500 Hz or better, SPL 124 dB [SPL @ 1% THD] Or better Signal-to-noise ratio 64 dB Including with Shock mount for fixing the microphone and should be from same OEM Approved Make- Clock Audio/Rode/Beyerdynamic
SITC of 17 U professional equipment rack with lockable door and power sockets, tray. Approved Makes: (President, VAL, Comm)
SITC of Large Microphone stand, Approved makes: (K&M, Ahuja, Samson)
SITC of Table Top Microphone stand, Approved makes: (K&M, Ahuja, Samson)
SITC of Blueray Player- Approved makes (Sony, Samsung, LG)
Connectors, Approved makes: Neutrik, Tasker, Switchcraft
SITC of WUXGA single DLP 7,000 ANSI Lumens or higher LASER PROJECTOR, Contrast Ratio 3000000:1 or better, Native 16:10 aspect ratio, HDBT support, 4k support, Display Colour 1.7billion or higher. Approved Makes: Christie, BenQ, Barco
SITC of Lens 1.25-1.6 for Projector, Approved Makes: Christie, BenQ, Barco
SITC of movable Matel frame for Cyclorama 4090 x 3450 with lockable wheels
SITC of Cyclorama Screen Matt White Perforated, perforation to be 1-2% of the screen area 3770mm x 2356mm
SITC Heavy weight Projector Mount 1:1
SITC of Stage box 12/4 (Approved Make- Rean, Link, Neutrik)
SITC of Microphone shielded cable 2 core, 6mm copper screen, 18 awg - 100meter roll Approved Make: (Tasker, Krystal, Belden)
SITC of 16 Pair digital Snake Cable, pproved Make: (Tasker, Krystal, Belden)
SITC of Speakers cable 2x4sqmm, pproved Make: (Tasker, Krystal, Belden)
SITC of Speakers cable Twinaxial 2x2.5sqmm, pproved Make: (Tasker, Krystal, Belden)
Auditorium Accoustic STAGE BACK & SIDE WALL Supply and installation of 25 mm thick pinewood wool magnesia bonded Colour panels square edge having fibers panels of size 25x600x2400 mm having density -400 kg/m3,weight- 10 kg/m 2 installed by using GI strut system. The GI strut work includes Ceiling channel (CC50) having thickness 0.45mm, length 3600 mm, knurled web 50, depth 50 mm and equal flanges of 13 mm & width 100 mm is fastened to Wall positioned horizontally in a regular manner at 600 mm centers . Then panels to be fixed on the cross channels CC 50 with suitable PVC fastener. Fasteners are fixed with unlocking channels as per standard practice of company. Colour panels shall be back lined with acoustical infill of synthetic poly fiber PF 5 x 50 mm thick adhered to the wall using stick 7 adhesive. Technical Parameters of the panels are : Core Variants -pinewood fiber, Fire - Class 1 & P , Acoustic - NRC 0.95 , Climate (OC RH ) - 50,90 , termite resistance - Yes , light reflectance - color dependent , Green - (RC%) - 10 , Hygiene (Vo C, Clean room) - Low , Strength - Load capacity (Kg ) - ball impact Test certificate will be submitted after procurement of materials.
STAGE CEILING Supply and Installation of strand wood wool fiber colour tiles square edge Magnesia bonded pinewood fibre/ dust core ceiling tiles of size 595x595x15mm having density 600 kgs/m3, weight 9-12 kg/m2 which is suspended by using 0.35mm thick and 24 mm wide pre coated metal skelet trelis T 24 HD powder coated grid system.The technical parameters are as follows : Core - Pinewood particle, Fire – Class 1 & P, Acoustics – NRC upto 0.9, Climate (OC RH) – 50, 90, Termite resistance ,Light reflectance – Low light reflective,Green (RC %) – 25,Hygiene (VoC, Clean room) – Low, Class 3, Strength, Load capacity (Kg) - Antisag, Ball-Impact. The T24 HD Grid system of 600 x 600 mm module shall include wall angle (WA 24x 20 x 3000 mm) , 0.43mm thick fixed along the periphery of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the Main T 24 x 32 x 3600 x0.35 mm from the soffit with the help of soffit cleat and wire rod along with leveling spring clip at 1200mm c/c. Cross T 24x 32x1200 x0.35mm is then interlocked into the pre-cut slots in the Main T 24 at 600mm centers in the direction perpendicular to the Main T24. Finally, Cross T24 (24 x 32 x 600 mm ) are then interlocked into the pre cut slots in the 1200mm Cross T24 at 1200mm centers and in direction parallel to the Main T24. Wood wool square edge of size 595 x 595 x 15 mm thick shall be placed into the grid size of 600 x 600 mm. Apply synthetic poly fiber PF 5x25 acoustic wool of 50 kg density to be kept on the top of the wooden ceiling by laying on the framework.Test certificate will be submitted after procurement of materials.
STAGE WINGS:-Providing and fixing at all heights of the wings on the stage consisting of metal tubular framework @ 1200x600 c/c out of 50x25x16G MS tubes duly given coat of red oxide primer after cleaning with emry paper. The wings to be rotatable 360 degree with pivot and ball bearing mechanism as per the shop drawing approved by the Architect. The wing to be lapped on both sides withj 12mm comply and 12mm UFoam glued over it . Fianlly fixing of the IFR black matt fabric of 330 GSM ( Nexgen/RSWM) over the foam. The edges to have 100mm wide 18mm thick teakwood edging on the peripherry.The work shall be executed as per drawings ,specifications & instructions of engineer in charge.
PLAIN CEILING ISOLATER ( LAYER - 1 ) FROM ROOF Supply and Installation of sandwitch doubler layer gypsum board with 2.5 mm TECSOUND 50 having high density polymer-based, asphalt-free, synthetic soundproofing membrane,weight - 5 Kg ,Density- 2.0Kg/m3, thickness - 2.5 mm , length 6 mt width - 1.22 mm sandwitch in between two layers having size 1800X1200 having density 600 kg /mt 3 & weight - 7.8 Kg /mt sq with fire class 1&P , Climate 0C, RH ( 50,90) STC - 48 db & green(Voc ,RC%) - Low ,10 make ( Saintgobain / Boral / Indis Gypsum ) to be fixed with Philips head screw by using concealed ceiling system. The concealed ceiling system shall include GI Wall channel(WC 25) having thickness 0.45 mm, length 3600 mm, unequal flanges of 15 & 20 mm and web of 22 mm should be fixed along the perimeters of the wall with nylon sleeves and suitable fasteners at every 300 mm centers. Then suspend Main channels (MC 45) having thickness 0.9 mm, length 3600 mm, equal flanges of 15 mm and web 45 mm from the soffit at every 1200 mm centers with Suspender angle(SA 25) having thickness 0.45 mm, unequal flanges of 25 & 10 mm. GI Ceiling channel(CC 25) having thickness 0.45 mm, length 3600 mm, knurled web 35 mm, depth of 25 mm and equal flanges 9.5 mm is fastened to the Main channel in the direction perpendicular to the Main Channel at every 600 mm centers. Now the jointing & finishing of the same will be done by using sealant to look flush. Now,1 mm Strand square edge of size 600 x 1200 x 15 mm thick shall be fixed screws on metal frames .After that apply Synthetic poly fiber PF 5 x 25 acoustic wool of 50 kg/m3 density to be kept on the top of the ceiling by laying on the frame work. Test certificate of the use products shall be submitted after procurement of materials.
CEILING WITH GRID SQUARE EDGE TILES With GYPSUM COMBINATION 40% (Layer - 2) Supply and Installation of 12.5 mm gypsum board plain ceilng with all metal frame works with a combination of grid ceiling with Rockfon grid tiles. 12.5 mm Gypsum boards are to be fixed on all the odd areas with philips head screw is fixed by using concealed ceiling system. The concealed ceiling system shall include GI Wall channel(WC 25) having thickness 0.45 mm, length 3600 mm, unequal flanges of 15 & 20 mm and web of 22 mm should be fixed along the perimeters of the wall with nylon sleeves and suitable fasteners at every 300 mm centers. Then suspend Main channels(MC 45) having thickness 0.9 mm, length 3600 mm, equal flanges of 15 mm and web 45mm from the soffit at every 1200 mm centers with Suspender angle(SA 25) having thickness 0.45 mm, unequal flanges of 25 & 10 mm. GI Cross channel(CC 25) having thickness 0.45 mm, length 3600 mm, knurled web 35mm, depth of 25 mm and equal flanges 9.5 mm is fastened to the Main channel in the direction perpendicular to the Main Channel at every 600mm centers. Now the jointing & finishing of the same will be done by using Anutone jointing kit consist of powder mixed with water and apply the same with flat flap on the boards joints to finish the surface of the boards so as to look flush. Apply synthetic poly fiber PF 5 x 25 acoustic wool of 50 kg density to be kept on the top of the ceiling by laying on the framework. Test certificate of the use products shall be submitted after procurement of materials.
CEILING WITH GRID SQUARE EDGE TILES With GYPSUM COMBINATION 60% (Layer - 2) Supply and Installation of Rockfone Stonewool tiles pacific square edge high sound absorption α w: 0,80 (Class B NRC (0.80), reaction to fire - A1, upto RH 100% no visible deflection in high humidity, Light Reflection - 86%, Sag Resistant 15 mm thick pacific Ceiling Tiles of size 600 x 600 E-Edge square edge with Anti- Bacterial Properties & M1 Class Emission Certification made up with Natural Stone (Bassalt Rock) a complete Green Product & perfectly suitable for any kind of False Ceiling application in builiding & costructions: Technical parameters - Core - stone wool fibers, Fire – Class A, Acoustics – NRC 0.99, Climate (degree C RH) – 50, 100, Light reflectance 86 %, Green (RC %) – 25, Hygiene (VoC, Clean room) – Low, The T 15 Grid system of 600 x 600 mm module shall include wall angle (WA15 W 30) with unequal flanges of size 15 mm wide, length 3000 mm, 0.40 mm thick fixed along the perimeter of wall with the help of nylon sleeves and suitable fasteners at 300 mm centers. Then suspend the Main T15 (MT 15 W 36) having flange width 15 mm, height 32 mm, and length 3600 mm from the soffit with help of soffit cleat and wire rod along with leveling spring clip at 1200 mm c/c. Cross 15 (CT15 W 26) with flange width 15 mm, height 26 mm, and length 1200 mm is then interlocked into the precut slots in the Main T15 at 600 mm centers in the direction perpendicular to the Main T15. Finally, Cross T15 (CT 15 W 06) having flange width 15 mm, height 26 mm, and length 600 mm are then interlocked into the precut slots in the 1200 mm Cross T15 at 1200 mm centers and in a direction parallel to the Main T 15. The grid system of 600 x 600 mm module shall be maintained for laying Rockfone stone wool steppe edge tiles of size 600 x 600 x 15 mm thick shall be placed into the grid size of 600 x 600 mm. Materials test certificate of the use products shall be submitted after procurement of materials.
SIDE WALL HALL (UPPER REACH) Above 1200 mm from floor level Supply and installation with 2.5 mm TECSOUND 50 having high density polymer-based, asphalt-free, synthetic soundproofing membrane,weight - 5 Kg ,Density- 2.0Kg/m3, thickness - 2.5 mm , length 6 mt width - 1.22 mm of Stretchable acoustical fabric NRC fabric system by using FR Grade NRC fabric of size 1700 mm width, shall be stretched by using wooden 10/15 mm plywood strip support base to fix rigid vinyl stretch tracks half wrap/ full wrap 15 mm FS15 & mid seam 15 mm FS 15, 15 mm pinewood magnesia bonded strand board, Synthetic poly-fiber 5x25 infill with requisite accessories & tools. Pinewood wood-based wool fiber shall have 15 mm thick square edge magnesite bonded pinewood fibers panels of size 600 x 1200 x15 mm having density 400 Kg /m3, weight 4 kg is first installed on the GI Channel CC25 on sidewalls which prefixed with adhesive / screw-on vertical wall insulation with TECSOUND 50 high density viscoelastic synthetic membrane size 1200 x 6000x 2.5 mm stick on the wall with overlapping of 100 mm to each other. Now place the GI framework on the top at 600 mm centers vertically / Horizontally with suitable fasteners. Now apply stick S7 adhesive on the top face of wood wool strand panels to stick the synthPF wool 5 x 25 mm thick adhered on strand tracks by following the fabric thread line or pattern. The fabric NRC is stretched & tucked into the stretch tracks & secure into the locking jaws so that it will be smooth, free of wrinkles with the tucking tools. Note - minimum 50 mm additional fabric is required for tucking hence maximum module wall fabric width would be 1600 mm The technical parameters of the system are core - pinewood fiber & poly-fiber Fire - 1 Acoustic - NRC 0.85 Climate OCRH - 49, 90 Termite resistance - yes, light reflectance - color dependant, Green RC % - 25, Hygiene ( Voc, Cleanroom ) - Low, Class 1. A test certificate will be submitted after the procurement of materials.
WALL PANELING WITH WOODEN SLAT HDF PLANK (LOWER REACH) Supply & installation 2.5 mm TECSOUND 50 having high density polymer-based, asphalt-free, synthetic soundproofing membrane,weight - 5 Kg ,Density- 2.0Kg/m3, thickness - 2.5 mm , length 6 mt width - 1.22 mmof wall panelling of Anutone / Tranquil / Mechtrix Nishabdm slats surco high density fibreboard made out of pure pinewood particles , Fire Resistance - Pink in colour core with 5 test Fire Resistance BS 476 part 5 , BS 476 part 6 , BS 476 part 7 ISO 1182 ASTM E662 Smoke Density - Melamine laminated finish, perforated wooden grooved HDF slats L16-2 (2 mm grooves @ 8 mm centres),tongue-groove edge for a seamless look of lineal dimension size 128 mm x 2440 mm x 16 mm thick having density 700 Kg /m3, weight -9 Kgs/m2 with back fleeces from soundtex Germany nonwoven acoustic to be pasted on slats surco is to be installed by using GI strut system. The technical parameters are as follows Core Variants - Fibreboard, Climate (OC RH) – 50, 70 Light reflectance – 75%,Green (RC %) – 25, Hygiene (VoC, Clean room) – Low, Class 1,Strength, Load capacity (Kg) - Anti sag, Ball-Impact. The concealed wall panelling system shall include prefixed with adhesive / screw-on vertical wall insulation with TECSOUND 50 high density viscoelastic synthetic membrane roll size 1200 x 6000x 2.5 mm stick on the wall. Now the GI wall channels (WC25) having thickness 0.45mm, length 3600mm, unequal flanges of 15 & 20mm and web of 25mm should be fixed along the perimeters of the wall with nylon sleeves and suitable fasteners at every 300mm centres. Then fixed Main channels (MC45) having thickness 0.9mm, length 3600mm, equal flanges of 15mm and web 45mm from the side wall & fixed at every 1200mm centres with GI cross channel (CC25) having thickness 0.45mm, length 3600mm, knurled web 35mm, depth of 25mm and equal flanges 9.5mm is fastened to the Main channel in the direction perpendicular to the Main Channel at every 600mm centres. The framework will maintain 50 / 75 mm gap from the walls. Now clad the wooden slats surco on the CC 18 with the help of centre & edge clips to get better locking of slats. The tongue & groove are to be properly aligned to get flush look . Synth poly fibre 5 x 25 having wool of 500 gsm to be filled between the horizontal & vertical studs as in filler with the help of wire / stick 7 adhesive. Test certificate of the use products shall be submitted after procurement of materials
Swimming Pool Electro Mecanical Filters (Vertical Type) Filters:TOTALLY ANTI-CORROSIVE Bobbin Wound filter,1200 mm diameter. Fitted with pressure gauge panel manual air bleeder, water drain and emptying plug.fitted with collector arms and diffuser made from unplasticized PVC and polypropelene. Filtration velocity 40m³/hr/m². Max.working pressure : 2.5 kg/cm². Flow rate = 30m³/hr. fitted with 2.5 inch 6 way Multiport valve Make: AQUA, Italy / Proteam Europa, Norway / Pentair, USA
110w In-line UV-C System for pool water Disinfection with 30mj dosing parameter. The set should contain two sets of 55w UV Lamp Having a life expectancy of not less than 9000 Hrs. Make : Certikin / Evoqua / eq.
AFM Glass Media for filter with granulometry between 0.4 - 0.8 mm. Make : Dryden, UK / eq.
Filter Glass Media with granulometry between 1 - 2 mm. Make : Certikin, UK / eq.
Horizontal monobloc Centrifugal pumps. Capacity : 3HP Motor 2900 rpm Capable of delivering 30 m³/hr @ 16m head and shut off head not exceeding 2.5kg/cm2 To be installed with anti-vibration pads.Duty 2 no.standby 1 no. 325+Please note that pump will be installed with pre-filter strainer .Make: Kirloskar / Willow / Equivalent
2.5 inch pre-filter FRP Lint Strainer.Make : Local
Main Drain Grates 300 mm x 300 mm ABS plastic support frame & grate fixing screws in SS. Max. Recommended flow 43 m3/hr @ 0.5 m/s Make : -Aqua,Italy /Proteam Europa/ Pentair, USA
Suction inlet in white ABS with cap internal 50mm.Make : - Aqua,Italy/Proteam Europa / Pentair, USA
White ABS plastic bottom inlet for concrete with S.S. screws and regulable flow. Max flow 7m3/hr. Make : -Proteam Europa/Atech Pool / Pentair, USA
Ladders & Gratings Imported Overflow model stainless steel AISI-316 ladders,width: 500mm, handrails dia 38mm stainless steel non-slip step.Supplied with anchoring fixtures. Make : -Proteam Europa/Aqua, Italy / Equivalent
No. of steps - 2.
No. of steps - 3
White Color Modular Gratings made in UV stabilized ABS. With Anti-spill design Snaps together on central spine thus enabling a flexible continuous run.antisplash. Ht.27mm, width: 245mm .Make : - Aqua, Italy/Proteam Europa / Pentair,USA
SS 450 mm vacuum head with 1.5" connection, to be trailed via cable with wheels. Make: Local
Transparent blue Copolymer vacuum hose 1.5" dia (40mm) 15 mtrs long. Including hose cuffs for connection to suction inlets.Make : -Aqua,Italy / Procopi,France / Proteam Europa
Deep bag net made in polypropelene and white polyester netting clip type connection.Make : -Aqua,Italy /Proteam Europa / EQUIVALENT
Surface net made in polypropelene and white polyester netting clip type connection.Make : -Aqua,Italy /Proteam , Norway/ EQUIVALENT
Curved brushes made in polypropelene for pool basins and scum liners clip type connection.Make : -Aqua,Italy /Proteam Europa/ EQUIVALENT
Straight brushes with stainless steel bristles.Make : -Aqua,Italy /Proteam Europa/ EQUIVALENT
Reinforced aluminium telescopic handle 4.8 - 8.4M long with clip type connection.Make : -Aqua,Italy /Proteam Europa/ EQUIVALENT
Algae Brush with Aluminium back and S. S. bristles, fixing with clip connection.Make : -Aqua,Italy /Proteam Europa / EQUIVALENT
Test kit for free chlorine & pH.Make : -Aqua,Italy / / EQUIVALENT
Following specifications to be adopted.The pipe sizes are to be calculated on the basis of the following velocities.RETURN LINE PIPE VELOCITY : 2.5M/SEC.OVERFLOW LINE PIPE VELOCITY : 0.8M/SEC.SUCTION LINE PIPE VELOCITY : 1.2 to 1.5M/SEC.All pipes shall be of ISI mark, Prince or Finolex or Supreme OF 10KG/CM2.All PVC / PP valves shall be of Cepex/ Proteam, Norway brand of minimum PN10 rating.In cases where PVC valves of above 250mm are not available, Gunmetal Valves of Audco or other Brand are acceptable.All standard fittings like bends, elbows, tees etc should be of similar rating of the pipes. However, in cases where special fittings are required and the same are to be fabricated on site due to non availability anywhere in the Indian market, then the contractor has to ensure that the fittings are fabricated of high grade chopped PVC fibre/ rovings and should be capable of withstanding working pressure of atleast 10kg/cm2. All pipes and fittings, including those fittings (specials) that are fabricated on site should be pressure tested to atleast 6kg/cm2 or 24 hours.All pipes shall be well supported with clamps or civil support, especially at joints.Quote Rate only per RM for Supply and Installation of following PVC pipes.UPVC Agreeculture Pipe 10/kg Pressure (Make : Finolex, Supreem)
160 mm dia
140 mm dia
110 mm dia
75 mm dia
63 mm dia
50 mm dia
PVC. Ball Valve (Make : Cepex )
110 mm ( Ball Valve )
90 mm ( Ball Valve )
PVC. Check Valve (Make : Cepex )
90 mm Wafer type
63 mm Spring type
Overflow gutter to be constructed in concrete and connected directly to the balance tank by 250mm four no.s gravity flow. Four surflow channels of 110 mm dia will be constructed in concrete in the floor of the pool for fresh water lines.The Main Header for the Delivery side of the Pump shall be not less than 140 mm.The Main Header for the Suction side of the Pump shall be not less than 160 mm Scope shall include -Installation and Laying of :All the electrical cables shall be conduited in flexible PVC pipes Electrical cables shall be of Finolex brand & the PVC conduits shall be ISI quality. The contractors scope of electrical works shall include connections / electricfication of all pool pumps, chemical dosing pumps and any other pool equipment that requires electrical connections, including installation of all electrical panels and necessary circuit breakers. The electrical panels shall be of ABB or Siemens make.
Chemical for commissioning and trial run
SS 316 anchor cups for lane floater to be installed at the water level.(Make : Atech Pool / Aqua, Italy / EQUIVALENT)
UNDER WATER LIGHTS 18 W, 12V Worm White underwater light, nicheless type with Resin Filled SS Casing and supplied 2.6 meter cable. The light shall be fitted/ removed with the use of SS screws to avoid coming loose like push fit lights. The lights shall be IP67 compliant. Make: Innitiative / Aquatech / EQUIVALENT
Deck box made in white ABS with three threaded outlets.Make: Atech Pool / AQUA, Italy/EQUIVALENT
Flexible conduit for carrying cable from underwater light to deck box. 1Meter length, threaded ends 3/4" & PG-16.Make: Atech Pool / AQUA, Italy/ EQUIVALENT
Transformers / SMPS for underwater lights, 300 VA. Step down to 220V to 12V .Make: ISI Quality
1.5 sq.mm. wire encased in plastic flexible conduit from the jn. Box to transformer.Make : Fenolex
TEMPERATURE CONTROL / POOL HEATING Outdoor Heat and Chill Pump Components Compressor : Scroll (low noise) , Evaporator Coils : tubes made of Copper & fins in aluminium , Fan : Axial , Condensor : Double sprial titanium tubes with PVC encased , Thermostat : Electronic thermostat with digital display of temp & other functions, Casing : Zinc Plated steel with PVC powder coating which withstand outdoor weather condition
Output : 46.00 kw input : 9.5 kw , Gas -407 C / R22. Power supply : 380V, 50 Hz , max. current : 16.4 amps , water flow : 15 m3/hr , inlet/outlet connection : 63 mm , Dimension : 1450 mm Height , width : 730, Length : 1080 mm approx, Weight : 140 kgs approx. In-Line Heater
Supply of 18KW on line heaters with in built coil, Thermostat for temperature controll, Contactor, Flow sensor etc. Make : Elecro, USA / eq. Isothermal Pool Covers 500 micron in density & has weight 0.48 kg per m2 , with blue top & its bubble type isothermal pool cover
Size : 30 m x 6.5 m
Size : 4 m x 4 m
Roller for Pool Cover Aqvastar SS316 Pool Cover roller suitable for cover sizes up to 6.5 Mtr for a Length of pool 30 meters
Inter connecting uPVC pipe of 10 bar for heat pump within 10 meter including fitings etc.
Electrical Panel for Heat Pumps
Installation and commissioning
Add 12 % GST
Add 1% Labour Cess
BSR INFRATECH INDIA LIMITED
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid