Repair of Pump Sets, starter, valves, cables, panels and connected works at pump house at Military Station Kanasar.

Amount

M&L for disconnecting suction/delivery lines and coupling, taking down from foundation base frame, opening including dismantling of centrifugal pump set of capacity 10 HP and replacement of worn out spare part and re-assembling and installing, commissioning & testing in same location complete all as specified & as directed. Note:- (i) The spare parts required to be replaced shall be measured and paid separately as ‘Supply Only’ under the relevant item here-in-after. (ii) Unit rate (quoted by the tenderer) shall be deemed to include for all minor spares/extras. The decision of Accepting officer regarding minor spares/extras shall be final, conclusive and binding.

Supply only the following spare parts for centrifugal pump set of capacity 10 HP against serial item No. 1.00 here-in-before as per existing make, complete all as specified & as directed. Note: All spare parts shall be fixed in the pumps only after prior inspection & approval.

SS Pump shaft.

CI Impeller complete with impeller key.

Shaft sleeve bronze with locking screw & lock nut.

Bearing suitable for pump set.

Wearing ring (DE&NDE) CI

Set of ‘O’ ring

CI gland cap with eye bolt complete.

GM gland sleeve bush.

M&L for disconnecting suction/delivery lines and coupling, taking down from foundation base frame, opening including dismantling of centrifugal pump set of capacity 20 HP and replacement of worn out spare parts and re-assembling, installing, commissioning & testing in same location complete all as specified & as directed. Note:- (i) The spare parts required to be replaced shall be measured and paid separately as ‘Supply Only’ under the relevant item here-in-after. (ii) Unit rate (quoted by the tenderer) shall be deemed to include for all minor spares/extras. The decision of Accepting officer regarding minor spares/extras shall be final, conclusive and binding.

Supply only the following spare parts for centrifugal pump set of capacity 20 HP against serial item No. 3.00 here-in-before as per existing make, complete all as specified & as directed. Note: All spare parts shall be fixed in the pumps only after prior inspection & approval.

SS Pump shaft.

CI impeller complete with impeller key.

Shaft sleeve bronze with locking screw & lock nut.

Bearing suitable for pump set.

Wearing ring (DE&NDE) CI

Set of ‘O’ ring.

CI gland cap with eye bolt complete.

GM gland sleeve bush.

M&L for disconnecting suction/delivery lines and coupling, taking down from foundation base frame, opening including dismantling of centrifugal pump set of capacity 25 HP and replacement of worn out spare parts and re-assembling, installing, commissioning & testing in same location complete all as specified & as directed. Note:- (i) The spare parts required to be replaced shall be measured and paid separately as ‘Supply Only’ under the relevant item here-in-after. (ii) Unit rate (quoted by the tenderer) shall be deemed to include for all minor spares/extras. The decision of Accepting officer regarding minor spares/extras shall be final, conclusive and binding.

Supply only the following spare parts for centrifugal pump set of capacity 25 HP against serial item No. 5.00 here-in-before as per existing make, complete all as specified & as directed. Note: All spare parts shall be fixed in the pumps only after prior inspection & approval.

SS Pump shaft.

CI Impeller complete with impeller key.

Shaft sleeve bronze with locking screw & lock nut.

Bearing suitable for pump set.

Wearing ring (DE&NDE) CI

Set of ‘O’ ring

CI gland cap with eye bolt complete.

GM gland sleeve bush.

M&L for disconnecting suction/delivery lines and coupling, taking down from foundation base frame, opening including dismantling of centrifugal pump set of capacity 40 HP and replacement of worn out spare parts and re-assembling, installing, commissioning & testing in same location complete all as specified & as directed. Note:- (i) The spare parts required to be replaced shall be measured and paid separately as ‘Supply Only’ under the relevant item here-in-after. (ii) Unit rate (quoted by the tenderer) shall be deemed to include for all minor spares/extras. The decision of Accepting officer regarding minor spares/extras shall be final, conclusive and binding.

Supply only the following spare parts for centrifugal pump set of capacity 40 HP against serial item No. 7.00 here-in-before as per existing make, complete all as specified & as directed. Note: All spare parts shall be fixed in the pumps only after prior inspection & approval.

SS Pump shaft.

CI Impeller complete with impeller key.

Shaft sleeve bronze with locking screw & lock nut.

Bearing suitable for pump set.

Wearing ring (DE&NDE) CI

Set of ‘O’ ring

CI gland cap with eye bolt complete.

GM gland sleeve bush.

M&L for disconnecting suction/delivery lines and coupling, taking down from foundation base frame, opening including dismantling of centrifugal pump set of capacity 50 HP and replacement of worn out spare parts and re-assembling, installing, commissioning & testing in same location complete all as specified & as directed. Note:- (i) The spare parts required to be replaced shall be measured and paid separately as ‘Supply Only’ under the relevant item here-in-after. (ii) Unit rate (quoted by the tenderer) shall be deemed to include for all minor spares/extras. The decision of Accepting officer regarding minor spares/extras shall be final, conclusive and binding.

Supply only the following spare parts for centrifugal pump set of capacity 50 HP against serial item No. 9.00 here-in-before as per existing make, complete all as specified & as directed. Note: All spare parts shall be fixed in the pumps only after prior inspection & approval.

SS Pump shaft.

CI Impeller complete with impeller key.

Shaft sleeve bronze with locking screw & lock nut.

Bearing suitable for pump set.

Wearing ring (DE&NDE) CI

Set of ‘O’ ring

CI gland cap with eye bolt complete.

Gasket Set

S&F in replacement flexible rubber type coupling suitable for following capacity motor pump set complete all as specified & as directed:-

Suitable for 10HP motor pump set.

Suitable for 20HP motor pump set.

Suitable for 25HP motor pump set.

Suitable for 40HP motor pump set.

Suitable for 50HP motor pump set.

M&L for taking down defective induction motor of following capacity from the foundation, disconnecting the electric connections coupling pulley and transporting to work shop, cutting down and removing existing burnt out copper winding, cleaning of slots and rewinding with solid copper conductor (winding wire) complete including varnishing, drying, ovening, overhauling, greasing and fixing in the same position, making necessary eclectic connecting and testing of induction motor complete all as specified & as directed. Make of winding wire : CHETAK/DEVIDAYAL/FINOLEX/ASIAN/EMGEE

Suitable for 10HP motor pump set.

Suitable for 20HP motor pump set.

Suitable for 25HP motor pump set.

Suitable for 40HP motor pump set.

Suitable for 50HP motor pump set.

S&F in repair 15 mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete, all as specified & directed.

S&F in repair 20 mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete, all as specified & directed.

S&F in repair 25 mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete, all as specified & directed.

S&F in repair 50 mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete, all as specified & directed.

S&F Power Contactor 3 Pole MNX-18 complete including taking down old unserviceable power contactor all as specified & directed.

S&F Power Contactor 3 Pole MNX-32 complete including taking down old unserviceable power contactor all as specified & directed.

S&F Power Contactor 3 Pole MNX-50 complete including taking down old unserviceable power contactor all as specified & directed.

S&F Power Contactor 3 Pole MNX-80 complete including taking down old unserviceable power contactor all as specified & directed.

Supply and fixing overload relay range 20-33 Amps direct mounting on MNX power contactor complete including taking down old unserviceable relay all as specified & directed.

Supply and fixing overload relay range 24-40 Amps direct mounting on MNX power contactor complete including taking down old unserviceable relay all as specified & directed.

Supply and fixing overload relay range 36-60 Amps direct mounting on MNX power contactor complete including taking down old unserviceable relay all as specified & directed.

Supply and fixing overload relay range 45-75 Amps direct mounting on MNX power contactor complete including taking down old unserviceable relay all as specified & directed.

S&F electronic type Single Phasing Preventer in existing panel boards (max 600V & min 380V) three phase 415 Volts variation voltage 4% tripping time 2-5 second maximum including disconnecting & taking down old unserviceable Single Phasing Preventer, complete, all as specified & directed. Make - Minilec / L&T / Siemens / ABB / BCH / Havells

M&L for repair to unserviceable sluice valve of size 80mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete, all as specified and directed.

M&L for repair to unserviceable sluice valve of size 100mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete, all as specified and directed.

M&L for repair to unserviceable sluice valve of size 150mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete, all as specified and directed.

Supply & fixing cast iron body sluice valve heavy duty class ‘PN-1.6’ of 100 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 100 mm bore, complete, all as specified & directed.

Supply & fixing cast iron body sluice valve heavy duty class ‘PN-1.6’ of 150 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 150 mm bore, complete, all as specified & directed.

Supply & fixing cast iron body sluice valve heavy duty class ‘PN-1.6’ of 80 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 80 mm bore, complete, all as specified & directed.

M&L for repair to existing leaking run lead joint of CI/DI pipe or fittings of 80mm bore spigot and socketed ends by dismantling joint by melting the lead with the help of burner/blower including taking out old spun yarn and re-jointing with & including additional quantity of Pig lead required and good quality of spun yarn and testing of joint including necessary excavation & earth work in any type of soil including dewatering complete all as specified & as directed.

M&L for repair to existing leaking run lead joint of CI/DI pipe or fittings of 100mm bore spigot and socketed ends by dismantling joint by melting the lead with the help of burner/blower including taking out old spun yarn and re-jointing with & including additional quantity of Pig lead required and good quality of spun yarn and testing of joint including necessary excavation & earth work in any type of soil including dewatering complete all as specified & as directed.

M&L for repair to existing leaking run lead joint of CI/DI pipe or fittings of 150mm bore spigot and socketed ends by dismantling joint by melting the lead with the help of burner/blower including taking out old spun yarn and re-jointing with & including additional quantity of Pig lead required and good quality of spun yarn and testing of joint including necessary excavation & earth work in any type of soil including dewatering complete all as specified & as directed.

Supply and fixing high tensile mild steel nuts, bolts & washers of any size, fixed in repairs, complete all as specified & as directed.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings complete, fixed to walls and ceilings or laid in floors, including taking up or down old unserviceable steel water tubing and connections of 15mm bore, complete all as specified and directed.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings complete, fixed to walls and ceilings or laid in floors, including taking up or down old unserviceable steel water tubing and connections of 20 mm bore, complete all as specified and directed.

M&L for galvanized steel water tubing medium grade of 25mm bore with & including all fittings complete, fixed to walls and ceilings or laid in floors, including taking up or down old unserviceable steel water tubing and connections of 25 mm bore, complete all as specified and directed. Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

M&L for galvanized steel water tubing medium grade of 40mm bore with & including all fittings complete, fixed to walls and ceilings or laid in floors, including taking up or down old unserviceable steel water tubing and connections of 40 mm bore, complete all as specified and directed. Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

M&L for galvanized steel water tubing medium grade of 50mm bore with & including all fittings complete, fixed to walls and ceilings or laid in floors, including taking up or down old unserviceable steel water tubing and connections of 50 mm bore, complete all as specified and directed. Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

M&L for galvanized steel water tubing medium grade of 80mm bore with & including all fittings complete, fixed to walls and ceilings or laid in floors, including taking up or down old unserviceable steel water tubing and connections of 80 mm bore, complete all as specified and directed. Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

M&L for galvanized steel water tubing medium grade of 100mm bore with & including all fittings complete, fixed to walls and ceilings or laid in floors, including taking up or down old unserviceable steel water tubing and connections of 100 mm bore, complete all as specified and directed. Note: - Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

M&L for earthing complete with galvanized iron earth plate electrode of size 600mmx600mmx6.3mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr deep below normal ground level, connected to and including GI strip 32 x 6mm (up to the body of the equipment) by means of GI bolts/nuts/washers, protected by 40mm bore GI light grade pipe. Earth plate shall be surrounded by packed layer of coal dust 300mm and common salt 15cm thick all around. 20mm bore GI light grade pipe for watering and including funnel, wire mesh, CI cover and frame, PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) as in earthing pit including necessary excavation and earth work, all as specified and shown in electrical plate No. 3 of SSR Part-I and connected to earthing test point and testing on completion including dismantling and taking out old unserviceable earthing.

Supply and fixing cast iron foot valve of size 150mm bore (ISI marked) flanged ends with rubber insertion sheet 3mm thick, nuts, bolts and washers including taking down old existing unserviceable foot valve complete all as specified & directed.

Supply and fixing cast iron foot valve of size 100mm bore (ISI marked) flanged ends with rubber insertion sheet 3mm thick, nuts, bolts and washers including taking down old existing unserviceable foot valve complete all as specified & directed.

Supply and fixing cast iron foot valve of size 80mm bore (ISI marked) flanged ends with rubber insertion sheet 3mm thick, nuts, bolts and washers including taking down old existing unserviceable foot valve complete all as specified & directed.

Supply and fixing non return valve (NRV) of size 150mm bore, cast iron body, as per IS 5312 (ISI marked), heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint complete all as specified and as directed including dismantling & taking out old unserviceable non return valve.

Supply and fixing non return valve (NRV) of size 100mm bore, cast iron body, as per IS 5312 (ISI marked), heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint complete all as specified and as directed including dismantling & taking out old unserviceable non return valve.

Supply and fixing non return valve (NRV) of size 80mm bore, cast iron body, as per IS 5312 (ISI marked), heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint complete all as specified and as directed including dismantling & taking out old unserviceable non return valve.

S&F in repair ammeter digital type, 0 to 100A range, flush mounting type, three phase, 415V, AC with CTs of ratio 100/5 A in all three phases complete all as specified & as directed.

S&F in repair voltmeter digital type, 0 to 600V range, flush mounting type, three phase, 415V, AC etc complete all as specified & as directed.

S&F indicator lamp LED type, 230 Volts, AC (Different colours for indicating R, Y, B phases) with holder including dismantling old one etc complete all as specified & as directed.

S&F MCCB, 4 Pole, 200 Amps rating, rupturing capacity 25 kA, 415 Volt grade, AC, 50 Hz, with adjustable Thermal - Magnetic release and making connections using suitable size copper lugs/thimbles and crimping tool, including disconnecting & taking down old unserviceable MCCB, complete, all as specified & directed.

S&F MCCB, 4 Pole, 160 Amps rating, rupturing capacity 25 kA, 415 Volt grade, AC, 50 Hz, with adjustable Thermal - Magnetic release and making connections using suitable size copper lugs/thimbles and crimping tool, including disconnecting & taking down old unserviceable MCCB, complete, all as specified & directed.

S&F MCCB, 4 Pole, 100 Amps rating, rupturing capacity 16 kA, 415 Volt grade, AC, 50 Hz, with adjustable Thermal - Magnetic release and making connections using suitable size copper lugs/thimbles and crimping tool, including disconnecting & taking down old unserviceable MCCB, complete, all as specified & directed.

S&F MCCB, 4 Pole, 80 Amps rating, rupturing capacity 16 kA, 415 Volt grade, AC, 50 Hz, with adjustable Thermal - Magnetic release and making connections using suitable size copper lugs/thimbles and crimping tool, including disconnecting & taking down old unserviceable MCCB, complete, all as specified & directed.

S&F MCCB, 4 Pole, 63 Amps rating, rupturing capacity 16 kA, 415 Volt grade, AC, 50 Hz, with adjustable Thermal - Magnetic release and making connections using suitable size copper lugs/thimbles and crimping tool, including disconnecting & taking down old unserviceable MCCB, complete, all as specified & directed.

S&F MCCB, 4 Pole, 32 Amps rating, rupturing capacity 16 kA, 415 Volt grade, AC, 50 Hz, with adjustable Thermal - Magnetic release and making connections using suitable size copper lugs/thimbles and crimping tool, including disconnecting & taking down old unserviceable MCCB, complete, all as specified & directed.

M&L for cutting/dismantling of PCC hardstanding / WBM road with soling & premix carpet of any description for repair/replacement of water supply pipe lines and disposal of debris & rubbish to a distance exc 250m but not exc 500m and making good the same with & including plain cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregate) complete all as specified & directed.

Collection of water sample from Pump house and RO Plant as directed and carry out testing from NABL approved Lab as per IS-10500 and IS-465 (suitable for drinking & Construction) and report to be submitted to AGE E/M Office.

S&F in replacement On load changeover switch of capacity 125 Amp 4 pole with steel sheet enclosures etc complete all as specified & directed.

S&F in replacement On load changeover switch of capacity 200 Amp 4 pole with steel switch enclosures etc complete all as specified & directed.

S&F in replacement chassis of angle iron suitable for centrifugal pump set of capacity 10 HP including all holes, earthing clamps, welding works and installing the new chassis with grouting the required size nut bolt on same position of pump set including testing and applying two coat of synthetic enamel paint over a coat of red oxide primer etc complete all as specified & as directed. Note : (i) Excavation, returning, filling, PCC work with grouting of nut & bolts with necessary form work etc including dismantling of pump set with delivery and suction lines and making necessary alteration by fixing pipe and bend, refixing and realigning again after doing foundation at pump house complete is deemed to be inclusive in above items. (ii) The cost of above to be inclusive in above items.

Blank

Ditto as per item No. 65.00 above but for centrifugal pump set of capacity 20HP.

Ditto as per item No. 65.00 above but for centrifugal pump set of capacity 40HP.

Ditto as per item No. 65.00 above but for centrifugal pump set of capacity 50HP.

S&F in repair brass air release cock upto 15mm fitted on pump set etc complete all as specified & as directed.

M&L for preparation of old painted exposed surface of centrifugal pump set of capacity 10HP with suction line from UG sump to pump set and delivery pipe line and outlet pipe line from pump set to wall/pit as observed inside pump house, operating valves (Non return valves/sluice valves/Gate valves) any size by removing dust, dirt, oil grease etc and painting with two coats of synthetic enamel paint of superior quality as per existing colour or as appropriate colour using spray gun and writing SM/MES no. to pump sets with white paint complete all as specified & as directed.

Ditto as per item No. 71.00 above but for centrifugal pump set of capacity 20HP.

Ditto as per item No. 71.00 above but for centrifugal pump set of capacity 25HP.

Ditto as per item No. 71.00 above but for centrifugal pump set of capacity 40HP.

Ditto as per item No. 71.00 above but for centrifugal pump set of capacity 50HP.

Supply & lying in replacement LT rubber mating chequered type of size 2mtrx1mtrx12mm thick as per IS-5424/1969 etc complete all as specified & as directed.

S&F in replacement electric shock treatment chart printed on A0 size of paper duly plastic laminated and fixed inside a wooden/PVC photo frame of 50 mm width with 3mm sheet glass and 6mm plywood backing and suitable hanging arrangement to wall with hooks/steel chain etc complete al as specified & as directed.

S&F in replacement First aid chart printed on A0 size of paper duly plastic laminated and fixed inside a wooden/PVC photo frame of 50mm width with 3 mm sheet glass and 6mm plywood backing and suitable hanging arrangement to wall with hooks/steel chain etc complete al as specified & as directed.

M&L for hard teak wood display board made of size 700mm x 1000mm with frame dully painted with two coat of synthetic enamel paint over a coat of pink primer complete with inside rexine for fixing of papers with movable glass fitting & locking arrangement etc complete all as specified & as directed.

S&F in replacement panel door lock as per existing size and make complete all as specified & as directed.

Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks three layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed.

M&L for name board with green acrylic radium sheet for pump house/installations with suitable sheet of size 1.20mtr x 0.90 mtr with suitable stainless steel frame work with pedestal of dimension 2.5 mtr x 1.2 mtr, 40 mm dia stainless steel rod including suitable size & shape of letters printed on both side with necessary earth work, PCC foundation etc including painting/framing work:- Note :- (i) Size and shape of letters and other things should be as per sample kept in GE office sample room. (ii) The cost of above items deemed to be inclusive in rate quoted.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT underground electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 50 sqmm 3.5 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified including dismantling & taking out old unserviceable cable. Notes:- (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately. (ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.

Excavating in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes, laying of cables, pipes etc not exc 10 Sqm on plan and getting out in soft/loose soil.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick in soft/loose soil.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified.

M&L for sub class ‘B’ (old size) clay bricks laid flat and dry abutting each other with gap between adjacent bricks not exc. 10mm for protection of underground electric cable in such a way that the length of brick is at right angle to the central axis of cable complete all as specified and as directed.

M&L for dry sand (Local Tibba sand) and punning for cushioning and cover for protection of under ground cable complete all as specified and directed. Notes :- (i) Approved local tibba dry sand free from vegetations, grass and other deleterious substances shall be used. (ii) For the purpose of payment only punned thickness shall be measured.

S&F 4 sqmm multistranded copper conductor, 3 core PVC insulated and sheathed copper screen protected 1100 Volts grade submersible flat cable fixed to column pipes with suitable clamps & jointing material complete including disconnecting & taking out old unserviceable cable.

S&F PVC insulated multistranded copper conductor wire 1100 Volts, 3 Core of size 06 Sqmm and connecting to pump set and to LT panel including flexible PVC pipe after taking down old un-serviceable cable etc complete all as specified & as directed.

S&F PVC insulated multistranded copper conductor wire 1100 Volts, 3 Core of size 10 Sqmm and connecting to pump set and to LT panel including flexible PVC pipe after taking down old un-serviceable cable etc complete all as specified & as directed.

S&F PVC insulated multistranded copper conductor wire 1100 Volts, 3 Core of size 35 Sqmm and connecting to pump set and to LT panel including flexible PVC pipe after taking down old un-serviceable cable etc complete all as specified & as directed.

S&F PVC insulated multistranded copper conductor wire 1100 Volts, 3 Core of size 50 Sqmm and connecting to pump set and to LT panel including flexible PVC pipe after taking down old un-serviceable cable all as specified & as directed.

S&F chlorine testing kit (chloroscope) complete with accessories like glass tube 03 Nos & toldine solution bottle 01 No for measurement of chlorine content in PPM from 0.1 to 5.00 PPM including replacement of old one etc complete all as specified & as directed.

(b) Fully automatic star delta starter with contractor, overload relay, single phase preventer and timer. (c) Neon indicating lamp RYB – 01 Sets (d) Wiring complete with multistranded copper conductor PVC insulated unsheathed cable of suitable size in rigid steel conduit stove enamelled complete from starter to pump terminal box. (ii) For 10 HP Pump (a) MCCB 32 Amps, 4 pole, 25KA, lcs=100% lcu with adjustable thermal and fixed magnetic setting 50 Hz, 415 volts grade – 01 Nos (b) Fully automatic star delta starter with contactor, overload relay, single phase preventer, amp meter and timer. (c) Neon indicating lamp RYB – 01 Set (d) Wiring complete with mutistranded copper conductor PVC insulated unsheathed cable of suitable size in rigid steel conduit stove enamelled complete from starter to pump terminal box. (iii) For 10 HP Pump (e) MCCB 32 Amps, 4 pole, 25KA, lcs=100% lcu with adjustable thermal and fixed magnetic setting 50 Hz, 415 volts grade – 01 Nos (f) Fully automatic star delta starter with contactor, overload relay, single phase preventer, amp meter and timer. (g) Neon indicating lamp RYB – 01 Set

(h) Wiring complete with mutistranded copper conductor PVC insulated unsheathed cable of suitable size in rigid steel conduit stove enamelled complete from starter to pump terminal box. (iv) KVAR Suitable for 20 HP, 10 HP Pump (a) 6 KVAR Capacitor Bank – 01 Nos (b) 2 KVAR Capacitor Bank – 02 Nos Notes : (i) LT panel base frame shall be grouted in PCC (1:2:4) type B-1 using 20mm graded stone aggregate. The base shall be 60cm height from the nearest road level/floor level or as directed. (ii) All incoming MCCB shall be connected through MCCB spreaders with incoming bus bar and incoming cable shall be connected with incoming bus bar. (iii) Drawing of LT Panel shall be got approved well in advance from GE before fabrication of LT Panel(iv) The quoted rate shall deemed to include supply & provision of 65mm lock with 2 keys. Make of Lock :- Godrej / Harrison / Link. (v) Cost of platform, MCCB spreaders, cable glands, locking arrangement with lock and key and any minor addition/alteration if required at site (the decision of GE will be final and binding regarding extent to which the change can be considered as minor addition/alteration) shall be deemed to be included in the quoted rates.

M&L for taking out existing flange joint of 80 mm dia & make new flange joint complete with rubber or fibre board gaskets, tightening by existing nut bolts complete with testing for flange joints etc complete all as specified & as directed.

M&L for taking out existing flange joint of 100 mm dia & make new flange joint complete with rubber or fibre board gaskets, tightening by existing nut bolts complete with testing for flange joints etc complete all as specified & as directed.

BALAJI PROJECTS

BIDAWAT ENTERPRISES