Provn of certain Special repair, Revenue and Minor works for at Old and New Mil Stn Kapurthala under GE Kapurthala.

Amount

Demolition of brick masonary built in CM including all quoins stones pillars etc and clearing rubish off the premises.

Demolition of reinforced cement concrete of any discription and any size, incl cleaning rubish off the premises.

Demolition and breking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar

Demolition of cement concrete in ground floor and paving n exc 15cm thickness (below or above the ground level) built in cement mortar.

Demolition of cement concrete (Un reinforced) of any description and in any position not otherwise specifically provided for all as specified and directed by Engineer - in - Charge .

Taking down cement plaster on brick or stone wall etc incl raking out joints, hacking for key scrubbing down with water etc.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft / loose soil for roads to required slope gradient, camber complete all as specified and directed by Engineer - in – Charge.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 Sqm on plan and n exc 1.5m in depth and qetting out including side form work for sport to side earth.

All as per Srl item No. 8 here in before but exceeding 1.5m and not exceeding 3m in depth all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 8 here in before but exceeding 3m and not exceeding 4.5m in depth all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick all as specified and directed by Engineer-in-Charge

Removal of excavated material to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point all as specified and directed by engineer-in-Charge.

M&L for hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface true surface all as spd and directed.

M&L for Brick work using sub class 'B' brick straight or curved on plan exc 6m mean radius in CM 1:4 including corbelling and arches where shown on drg racking out joints internally and flush externally as the work proceeds complete all as specified.

All as per srl item No 14 hereinbefore but except bricks.

M&L for 15mm thick cement plaster in cement mortar 1:4 with water proofing compound @ 3% by weight of cement of as per manufacture's instructions whichever is higher to brick or concrete surface trowelled to even and smooth finish without using extra cement (WPC shall be measured and paid separately)

Supply only integral water proofing compoound..

M & L for rendering 15mm thick on fair faces or other than fair faces of brick work in CM 1:6 finished even & smooth without using extra cement all as specified and directed by Engineer - in - Charge .

M & L for 10mm thick rendering in Cement Mortar 1:4 to ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed by Engineer - in - Charge .

M & L for applying two coat of cement base paint on new plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer - in – Charge

M & L for applying two coat of white lime wash on new plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer - in – Charge

M&L for three coat of white wash on plastered/unplasterd surface on ceiling including preparation of new plastered surface complete all as spd and directed.

M & L for pre-cast RCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in man hole cover slabs, of any thickness, size or shape including necessary from work, finished concrete surfaces fair and even in cement mortar set in CM 1:4 all as specified and directed by Engineer - in - Charge.

M&L for Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete all as specified and directed by Engineer - in - Charge

M & L for 75 mm thick PCC 1:2:4 type B-2 with using 40 mm graded stone aggregate as in hardstanding/flooring/plinth protection finished even and smooth without using extra cement all as specified and directed by Engineer-in-Charge.

M&L for 75 mm thick Cement concrete type C1, 1:3:6 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing and plinth protection.

M&L for 75 mm thick Cement concrete type C1, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing and plinth protection.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate crushed as in mass filling/foundation complete all as specified

M&L for Providing precast cement concrete M-15 (PCC 1:2:4) type B-1 using 20 mm graded stone aggregate as in man hole cover slabs set in cement mortar 1:6 incl necessary form work if any and finishing exposed surface even and smooth complete all as specified

M&L for Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate as in drain/channel of manhole including slightly rounded or chamferd at edges comp all as specified

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in benching for manholes bands coping bed plate etc with slightly chamfered or rounded angles including necessary form work, if any and finishing exposed surfaces eveen and smooth without using extra cement complete all as specified.

M&L for 100mm thick PCC 1:2:4 type B-2 using 40 mm graded stone aggregate as in hard standing and finishing exposed surfaces eveen and smooth without using extra cement complete all as specified.

M&L for Forming 12mm thick Expansion joints for 150mm thick filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’thickness of slab complete all as specified

M&L for Reinforced concrete pipe class NP-3, 200mm bore of pipe laid and jointed with coment complete including collars.

M&L for cement concrete 1:3:6 type C2 with using 20 mm graded stone aggregate as bed to 200 mm bore drain pipes inclding forming cradles all as specified

M&L for TMT bars 10mm dia and over cut to length bent to shape including cranking, hooking ends and binding with anfg including MS wire (annealed) not less than 0.9mm dia complete all as Specified.

All as per Srl item No. 36 here in before but 5mm dia and over upto 10mm dia as in stirrups, spacers and binders all as specified and directed by Engineer - in - Charge.

Cutting into existing man hole for connecting new drain and making good etc for 200 mm bore pipe and rendering cutting out existing benchng for and forming branch (1/2 round or 3/4 section) channel in cement concrete PCC 1:2:4 type B-1 smooth finished and reforming benching as required and specified.

Extra for forming fair finish for drain channel or girth n.exc 30 cm with cement complete all as directed by Engineer-in-charge.

S&F Mild steel work using any section as in steps rung, band handles and similar small article fixed independent mad to shape and duly tarred and sanded complete all as specified (PCC for filling for MS steps shall be measured and paid separately.

S&F Steel rolling shutters, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, thickness of lath is 1.25mm but gear operated type with bevel gear box and crank handle complete all as specified and directed by Engineer - in - Charge.

M & L for preparation of new painted steel surfaces of any description over 10 cm width of girth not otherwise described and applying two coats of synthetic enamel paint all as specified and directed by Engineer - in - Charge .

M&L for Non - skid jointless coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M & L for glazed coloured ceramic tiles 300x200x7mm thick as in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15mm thick cement plaster in CM 1:4 complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over & including 20mm thick cement screed bed in cement mortar 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade including rubbing and mirror polishing complete all as specified and directed.

M&L for Machine cut kota stone 20-25mm thick as on vertical surface as in in riser of steps, skirting, dado etc over & including 15mm thick rendering in cement mortar 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade including rubbing and mirror polishing complete all as specified and directed..

M&L for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing given in SSR-2010 Part-I.

S & F factory made solid panel PVC door/ cup board shutter 25mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width & stick inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, Paneling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, supplying & fixing in the frame at site as per specification & drawing as mentioned in SSR-2010 Part-II complete all as specified.

S & F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed by Engineer - in - Charge .

S & F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 sqm in each pane all as specified and directed by Engineer - in - Charge .

S & F Aluminium anodised barrel tower bolt of extruded section 150mm long all as specified and directed by Engineer - in - Charge .

S & F aluminium alloy anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheets cast or extruded section and fixing bolts of extruded section or cast aluminium alloy 250mm size all as specified and directed by Engineer - in – Charge .

S & F aluminium handle cast type anodised, 125mm long all as specified and directed by Engineer - in - Charge .

S & F 15mm bore stop valve, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed in repair all as specified and directed by Engineer - in – Charge.

S & F 20mm bore medium grade tube galvanised with all fittings and fixed complete to wall/ceiling or laid in floor all as specified and directed by Engineer - in – Charge .

S & F 15mm bore medium grade tube galvanised with all fittings and fixed complete to walls & ceiling or laid in floor all as specified and directed by Engineer - in – Charge .

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S&F 110 mm bore PVC (SWR) bends any radius.

S&F 75 mm bore PVC (SWR) bends any radius.

S&F PVC SWR floor trap 100mm dia with grating including jointing to waste pipe with solvent cement in repairs all as specified and directed by Engineer - in - Charge .

S&F PVC SWR floor trap 75mm dia with grating including jointing to waste pipe with solvent cement in repairs all as specified and directed by Engineer - in - Charge .

M & L for providing reinforced/unreinforced cement concrete (1:2:4) B-1 using 20mm graded stone aggregate as in lintels up to 1.5 m clear span, benching, coping, bed blocks and roof kerbs etc including use of necessary form work all as specified and directed by Engineer - in - Charge .

S & F rotational moulded polythene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I of capacity 500 Litres all as specified and directed by Engineer - in - Charge .

M&L for Cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in bed to drain pipe including packing under and haunching against the sides of pipes 150mm dia (internal) after these are laid in trenches all as specified and directed by Engineer - in - Charge.

M & L for 150mm dia (internal) SGSW pipes grade ‘A’ laid in trenches and jointed all as specified and directed by Engineer - in - Charge.

M & L for RCC M-25 as in foundation, plinth beams, raft footings complete all as specified and directed by Engineer - in - Charge.

M & L for RCC M-25 as in slabs etc complete all as specified and directed by Engineer - in - Charge.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benches for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150mm internal dia for pipe is 150 mm all as specified and directed by Engineer - in - Charge.

S & F Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed by Engineer - in - Charge

S & F Pillar taps 15mm, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer - in - Charge

S & F in repairs Vitreous China bowl urinal angle back of size 430 x 370 x 340mm with grating and union for discharge paipe including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete all as specified and as directed by Engr-in-Charge etc complete all as specified.

S & F in repair PVC connection 15mm size with PTMT of length300mm all as specified and directed by Engineer - in – Charge.

S&F shelf of PTMT fixed with and incl. chromium plated brass screws and wooden cleats complete all as specified and directed by Engineer - in - Charge.

S&F Towel rail 600mm long of PTMT fixed with and incl. chromium plated brass screws and wooden cleats complete all as specified and directed by Engineer - in - Charge

S & F 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed in repair all as specified and directed by Engineer - in – Charge.

S & F 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all as specified and directed by Engineer - in – Charge.

M & L for chequered cement concrete tiles 20cm x 20cm x 25mm thick set, jointed and pointed in neat cement slurry and pigments as in floors complete all as specified and directed by Engineer - in - Charge .

M & L for 20mm thick Screed bed or bedding layer of mortar 15mm thick in CM 1:6 for laying floor finishes complete all as specified.

M&L for 25mm thick cement concrete type B0, 1:2:4(12.5mm graded crushed aggregate) as in floor incl fair finished even and smooth without using extra cement complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C-1 (using 20mm graded agg) as in plinth protection, 50mm thick and finished even and fair without using extra cement all as specified and directed.

M&L for Framed work as in doors or gate of angle iron or other section with gusset plate, rails braces, hold fast etc. complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening and fixing complete all as spd and directed.

M&L for 1.60mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel painting over a coat of red oxide primer all as specified and directed.

M & L for providing, cement concrete Type B1 1:2:4 (20mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering,slightly rounded or chamfered angles and throating, complete all as spd and directed.

M & L for machine pressed precast conc. interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade with grey cement and pigment complete all as specified and directed by Engineer - in - Charge.

Supply and filling of sand under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer - in - Charge.

Providing,cement concrete 1:3:6 type C1 with using 20 mm graded stone aggregatge as in roof kerbs or mud stops,rounded or chamfered on edges complete all as specified and directed by Engineer - in - Charge.

Taking up or down steel tubing 15mm bore & connection including cleaning for refixing or removal to store.

Taking up or down steel tubing 20 mm bore & connection including cleaning for refixing or removal to store.

S&F in repair Brass chromium plated single towel rail 20mm dia, D type, 600mm long between flanges as per cat part no AKP-35711P of jaquar complete all as specified & directed.

S&F in repairs Chromium Plated long body Bib taps, cast copper alloy with crutch or butterfly handle with wall flange with aerator, screwed down, screwed for iron pipe or for brass ferrule and fixed of 15mm bore complete all as specified and directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed . (Make: Prayag/ Polytuff)

S&F Brass Chromium plated angular Basin Inlet Connection (Angle Valve) quarter turn, with wall flange fancy type cast copper alloy 15 mm bore any colour (Model Essco, Marvel series Cat No MQT- 526) or equivalent fixed in repair complete all as specified and directed.

S& F brass CP mixture valve Centre hole, cast copper alloy(ISI Marked) fancy type chromium plated for mixing hot and cold water screwed down high pressure with capstan head screwed both ends for iron pipe 15mm bore dia complete all as specified and directed.

S&F in repairs Brass CP wall mixer with 115mm bend pipe for connection to overhead shower for mixing hot & cold water screwed down for iron pipe and fixed of 15mm bore complete all as specified and directed.

S&F in repair for fancy type chromium plated two way stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed for bore of size 15mm.

S&F deeplax stainless steel towel rack of size 600mm made of stainless steel complete all as specified.

S&F fancy type Stop valves, chromium plated with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed of 15mm bore complete all as specified and directed.

S&F CP stop valve/angular valve cast copper alloy screwed down for 15 mm bore dia iron pipe all as specified and directed.

S&F Vitreous China Ware Wash hand basin white, flat back, size 210 x 580 x 460 x mm size with long padestal, 32mm dia stainless steel waste coupling & CI Brackets including cutting for and pinning ends of brackets or erecting stand complete.

S&F coloured Toilet paper holder of CP fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

S&F health faucet with 15 mm with CP angle cock all specified by Engineer in Charge

S&F coat hooks of 6 numbers aluminium powder coated mounted mouned on aluminium powder coated plate 50X300 mm fixed to walls all as specified by Engineer in Charge

S&F glass self 450X150 & 8 mm thick with chromium plated railing with chromium plated brackets complete all as specified by Engineer in Charge

S&F corner glass shelf of size 300mm dia 8mm thick with chromium plated bracket complete all as specified by Engineer in Charge

S&F in repairs Sensomatic sensor flushing valve for urinal with complete kit (suitable for urinal) all as specified and directed by Engr-in-Charge (Cat part No URS-WHT-0704) Make jaquar

S&F Vitreous China Ware Wash hand basin white, flat back, size 210 x 580 x 460 mm size with long padestal, 32mm dia stainless steel waste coupling & CI Brackets including cutting for and pinning ends of brackets or erecting stand complete all as specified and directed.

S&F Vitreous China Ware Bowl for couple closet WC with soft closing seat cover, size 360x679x774mm, S trap-220 mm along with cistren with complete all as specified and directed by Engr-in-Charge.

S & F in repairs 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed in repair all as specified and directed by Engineer - in – Charge.

S & F in repairs 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all as specified and directed by Engineer - in – Charge.

S&F in repairs 32 mm bore PVC waste cupling with PVC waste pipe for WHB complete all as specified and as directed.

S&F Pre painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

S&F 100 mm size Butt hinges, medium weight, Stainless steel,

S&F bib taps 15mm bore dia, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe all as specified and directed by Engineer – in – Charge .

S&F 75mm PVC(SWR) vent cowl complete all as specified and directed.

M&L for Flush pointing to brick wall in CM 1:4 all as specified and directed.

M&L for Keyed pointing to brick wall in CM 1:4. all as specified and directed.

S&F MS rolled section of angle as in door frames with provn of fixing of hinges or arrangements for hangings etc conforming to Fe 410 W(Gde E-250) complete all as specified and as directed by Engineer-in-Charge.

Cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as depth of embedded portion for holdfasts or lugs measured from the face of the jamb into Exc. half brick but not exc. one brick wall

Cutting openings, through brick walls built in cement mortar for door, window and other openings or enlarging existing openings, converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc., to store and rubbish not exc. 50m

Forming jambs, etc., to openings (to foregoing item), including cutting, toothing and properly bonding into old work in Cement mortar 1:4 or cement lime mortar 1:2:9, also facing, jointing and pointing to match existing work, complete

Making good under cills or over arches, lintels and bressummers, including all-pinning when necessary in Cement mortar 1:4 or cement lime mortar 1:2:9.

M&L for Preparation of newly plastered wall surfaces and applying two coats of distemper oil emulsion over one coat of primer including birla putty 3mm thick complete all as specified and directed.

S & F steel window 1.25mm thick Box type ( primer coated) ERW hollow P section of size 60mm x 25mm single rebated comprises glazed Skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T- Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T- Section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC ( 1:2:4) type B-1 Four Nos for each window) including following fitting welded to frame shutter: (a) Mild Steel Hold Fast,150mm long of 12mm Square bar made to shape – 04 Nos per window (b) Handles of Z Sec 20mm x 100mm long (c) stopper – 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mmx63mm welded to hinges – 01 No per leaf (e) Mild steel Pintal hinges of size 75mmx75mmx12mm-02 Nos per leaf (f) Grills made out of MS square bar 12mm dia welded to FI frame 25 x 3mm complete all as specified and directed and shown on drawings. Note: (i) Glass shall be measured and paid separately under appropriate item of Sch 'A' (ii) Irrespective of whatever shown on drgs, MS gills shall be of 12mm dia MS square bar.

S & F steel window 1.25mm thick Box type ( primer coated) ERW hollow P section of size 60mm x 25mm single rebated comprises gauged Skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T- Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T- Section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC ( 1:3:6) type C-1 Four Nos for each window) including following fitting welded to frame shutter: (a) Mild Steel Hold Fast,150mm long of 12mm Square bar made to shape – 04 Nos per window (b) Handles of Z Sec 20mm x 100mm long (c) stopper – 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mmx63mm welded to hinges – 01 No per leaf (e) Mild steel Pintal hinges of size 75mmx75mmx12mm-02 Nos per leaf. Note: wire mesh shall be measured and paid separately under appropriate item of Sch 'A'.

M&L for prepration of newly steel surface over 10cm width or girth and applying two coats of syntheic enamel paint .

COSMO BUILDERS

G M BUILDERS 36