GE I R AND D/CHD-61/2026-27 REPAIR TO ROAD, PATH, CULVERTS AND ROAD FURNITURE IN ZONE-VI, VII, MG ZONE AND OUTER PERIMETER AT TBRL RANGE RAMGARH

Material and labour for repair to potholes any depth, not exc 1 Sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc, cutting around edges making good by applying tack coat @ 5 Kg per 10 Sqm, putting in premixed bituminous macadam, well rammed and sealed with binder 9.8 kg per 10 Sqm, blinded with 0.09 cum of stone chippings, 6.3mm size and again well rammed (including supply of premixed macadam, binder and chippings), depth of potholes exc 30mm rolled and compacted to required camber and gradient with 8 to 12 tonne power roller, complete all as specified and directed.

Scarifying or picking gravelled macadam or bituminous macadam surfaces in area n.exc 400 Sqm and exc 50 mm and n.exc 100 mm deep complete all as specified and directed.

Preparing old black top surfaces by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc and applying evenly a priming/tack coat with bituminous primer at 10kg per 10 sq metre over bituminous macadam complete all as specified and directed.

Material and labour for repairs to unlevelled surfaces by filling in premixed bituminous macadam using paving bitumin VG-30 @ 4% by weight of total mix laid, rolled and compacted to required gradient and camber with 8 to 12 tonne power roller (consolidated thickness of 75mm or less) and laid by mechanical paver finisher complete all as specified and directed.

Material and labour for preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleared surfaces with gunny bags to remove all loose dirt etc and applying evenly a priming tack coat with bituminous primer by using paving bitumen of VG-10 grade @ 5 kg/10 Sqm complete all as specified and directed.

Material and labour for laying, spreading 30mm thick (consolidated thickness) bituminous premix semi dense asphaltic concrete with 5.5% binder content of bitumen of VG-30 grade by weight of total mix, made with self propelling mechanical paver, rolled and consolidated to reqd camber and gradient with 8 to 12 tonne power roller to a uniform smooth surface complete all as specified and directed. Note :- (i) Work shall be executed as per design mix approved by the GE. (ii) Filler shall be cement (OPC-43 Grade) (iii) Any variatiion in binder content during design mix at site on plus side shall be borne by the contractor without any extra cost to the department. However, if binder content works out to be on minus side during design process (i.e less than 5.50%) same shall be adjusted considering the bitumen rate given in particular specification.

Material and labour for painting lines, dashes, arrows, letters, etc. with adequate no of coats on roads, pavements and the like exc 10cm wide with road marking paint, white or golden yellow complete all as specified and directed.

Supply and fixing in repair solar powered LED road studs /cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency monocrystalline solar panel 2.4V/ 0.3 watt one NI-Cd rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd as per manufactures instructions etc. complete all as specified and directed.

Supply and fixing in repair for metal tubular delineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed.

Supply and fixing in repairs road studs/cat eye reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions complete all as specified and directed.