PROVISION OF SINGLE LIVING ACCOMODATION, COOK HOUSE, DINING HALL AND SCOOTER SHED FOR AIRMEN AT AFS PANAGARH

Design

SCHEDULE "A" PART- III ( INTERNAL ELECTRIFICATION) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-IV ( INTERNAL WATER SUPPLY ) Details of prepriced Schedule is given in tender documents.

and construction of Bore Well Room in single storey configuration with RCC framed structure and permanent specification complete all as specified and as shown in drawing.

SCHEDULE "A" PART- VI (AREA DRAINAGE) Details of prepriced Schedule is given in tender documents

SCHEDULE "A" PART- VII (SEWAGE DISPOSAL) Details of prepriced Schedule is given in tender documents

SCHEDULE "A" PART- VIII (EXTERNAL WATER SUPPLY) Details of prepriced Schedule is given in tender documents

SCHEDULE "A" PART- IX (EXTERNAL ELECTRIFICATION) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART- X (STREET/SECURITY LIGHT ) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART- XI (DEMOLITION) Details of prepriced Schedule is given in tender documents.

re die cast housing, LED type 1 x 36 W/ nearest higher available rating all as specified and directed suitable for battery system of 12 Volts DC (b) Maintenance free Lithium Ion Battery 1 No of minimum 12V, 100 AH @ C10 rating (12 Volt system) all as specified and directed. (c) Mono crystalline solar photovoltaic module array panel conforming to all relevant IEC/IS standards of best quality. Solar Panel shall be min 125 Wp(12 Volt system). The panel shall be suitably connected to battery through charge controller for its charging all as specified and directed. (d) Solar Charge controller MPPT based conforming to relevant IEC/IS standards shall be provided to charge the battery from solar photo voltaic array panel all as specified and directed including suitable protection mechanism. (f) Steel Octogonal pole, hot dip galvanised, 3 metre height, conforming to relevant IS/IEC standards. The earth work, PCC foundation etc for pole shall be as per manufacturer guidelines and quoted rate is deemed to be included the same. (g) All the electrical fittings, batteries, solar photo voltaic array panel shall be fixed on a pole of suitable height from ground level all as specified and directed Note :- All the items like solar photo voltaic array panel, luminaire, solar charge controller, batteries etc shall confrom to relevant IEC/IS standards.

Supply and fixing thermal foam insulation with glass wool & aluminium covered pipe for GI pipe self adhesive pipe foam thickness 5mm, suitable for 25mm GI pipe for protection to hot water pipe complete all as specified and directed.

Supply and fixing thermal foam insulation with glass wool & aluminium covered pipe for GI pipe self adhesive pipe foam thickness 5mm, suitable for 15mm GI pipe for protection to hot water pipe complete all as specified and directed.

Supply and fixing miniature circuit breaker (MCB) SPN of upto 20 amp rating 240V, 10KA 'C' curve and 10 KA current carrying capacity in the MCB DB complete with connection testing and commissioning, complete all as specified and directed.

INTERNAL WATER SUPPLY S&F brass angle stop cock CP high pressure with capstan head long shank screwed down 15mm dia. bore complete all as specified and directed.

Material & Labour for providing 100 mm thick (compacted thickness) Wet Mix Macadam (WMM) in two layers (each layer 50 mm thick, compacted separately) with crushed stone aggregate of specified grading, spread using mechanical sensor paver / grader as specified, rolled and consolidated using 8 to 10 tonne capacity tandom vibratory power roller to required gradient and camber to achieve minimum 98% density of MDD determined using modified procter density determination method as per IS 2720(Part-8) and as per MORTH clause 406 for NEW RIGID PAVEMENT, complete all as specified and directed.

M&L for development of trial bore by reaming upto 525 mm for 200 mtrs depth from ground level using any suitable method as per soil condition and CGWB report including disposal of spoil from the site of work complete all as specified and directed.

Supplying and assembling including jointing, lowering & fixing in position threaded uPVC casing pipe of 150 mm dia nominal size (internal), 7.5 mm wall thickness (Min), Class CM,as per IS 12818 : 2010 (ISI marked) of suitable length including socket and jointing materials, complete all as specified and as directed.

S&F flat submersible cable 3 core 1100 volt grade multi stranded copper conductor PVC insulated, water proof, ISI marked of size 6 sqmm for connecting from starter to bore well submersible pump sets complete all as specif

Materials and labour for boring of holes under road, pavement, hard standing by trenchless technology using ultra sound technique and necessary machine etc. including HDPE pipe of 150 mm dia suitable for 0.4 Mpa working pressure complete all as specified and directed.

STREET/SECURITY LIGHT Supply and fixing 8 Mtr Long Hot Dip Galvanised Street Light Octagonal Pole with Foundation type Base Plate and Foundation Bolts and additional structural steel as reqd, dimentions of Pole as Top Diameter - 70 mm, Bottom Diameter- 130 mm, Thickness - 3 mm, Foundation type Base Plate (200 x 20 x 16 mm), Foundation Bolts - 4 Nos 20 mm dia, pitch circle dia 200 mm, bolt length 600 mm, projects bolt length as per OEM recommendation Single type arm bracket 1500 mm long , top dia 70 mm , suitable for LED Street Light fitting. The Pole shaft shall have octagonal cross section and continuously tapered with single longitudinal welding complete all as specified and directed.

Note:- Schedule of cedit (Sch 'A' Part- XIII) amount of Rs 3,10,500.00 shall be deducted from the total quoted amount of BOQ.

Supply, jointing, testing and laying in trenches/floor/wall etc in standard lengths, Centrifugally Cast (Spun) Ductile Iron (DI) Pressure Pipes with Spigot & Socket end, Class K-9 conforming to IS: 8329/2000 and amendment No.1, suitable for (push-on) rubber gasket jointing with inside cement mortar lining and outside zinc coating with finishing layer of Black Bitumen/Blue Epoxy coating, ISI marked of the following dia Pipe (nominal diameter), including push on rubber gasket joints complete all as specified and as directed. Note : (i) DI specials/ fittings will be measured and paid separately under relevent items of Schedule (ii) The cost of push on type joint deemed to be included in the rate quoted.

(a) 150 mm dia

(b) 80 mm dia

M&L for DI fittings ISI marked of size 80 - 200 mm bore suitable for DI pipes class K-9, PN 10, as per IS: 9523 / 2000 with inside cement mortar lining andoutside Zinc coating with finishing layer of Black Bitumen, such as bends (any type radius & angle) tapers, tee pieces, single branches, Y junctions, double junctions, connecting pieces, Nuts & bolts, gaskets, flanges, including push on rubber joints etc. complete all as specified and directed.

Srl Item No. 99.00 Contd... (a) Luminaire :- IP 65, full body, aluminium pressu

SCHEDULE "A" PART -XII (MISCELLANEOUS ITEMS) Note:- Srl Item No. 2.00 to 6.00 and this schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col.' F ' signifies this fact only.

Supply, install, testing and commissioning of indoor wall mounting type cubical type LT Control Board, factory fabricated CPRI type tested with suitable neoprene rubber gasket to make it completely dust & vermin proof & degree of protection not less than IP-43 & general construction confirming to IS-13947, front openable. The panel shall be provided with ventilation facility in the form of louvers for better heat dissipation & tinned copper bus-bar wrapped with coloured PVC tape/sleeves of rating in conformity to the Incoming MCCB rating. The panel board shall be fabricated out of 2.0 mm thick CRCA sheet duly pre-treated & powder coated, supporting frame made out of 50 x 50 x 6 mm angle iron suitable for 3 Ph, 4 wire system 415/440 volts grade incl complete internal wiring with not less than 2.5 sqmm copper wire incl cable glands of suitable sizes complete all as specified and as directed with & including the following accessories :- (LT Panel for Bore Well)

Srl Item No. 65.00 Contd... (b) Multi Grade Filter, vertical cylindrical type , MS fabricated vessel of suitable size as per IS-2062, incld pipeline butterfly valve of suitable size incld 2 nos. pressure gauge, sampling cocks filled with Sand, activated sand, gravels etc as per OEM design. The shell thickness shall be of 8mm and dished end having 6mm with header and lateral collecting system. Multi Grade filter should have Food grade (Non toxic) Epoxy paint from inside and outside two coat of synthetic enamel paint of approved paint over a coat of red oxide paint. The shell shall also be provided with adequate size of air vent line with valve etc. Diameter of vessel of MGF shall be - minimum 2000mm and Height on Straight - minimum 1875mm. (Necessary Civil work, foundation, PCC, RCC, excavation , returning and filling etc shall be deemed included in the quoted rate). - 01 Set (c) Chemical Dosing System (CDS-4 with High Speed Agitator ) for Soda Ash at raw water collection tank with electromagnetic metering run on 220 V AC for 100% accurate dosing with all electrical connections with 200 ltrs PVC tank- 1 No. (Necessary Civil work, foundation, PCC, RCC, excavation , returning and filling etc shall be deemed included in the quoted rate).- 01 Set

Srl Item No. 65.00 Contd... (d) Chemical Dosing System (CDS-4 with High Speed Agitator) for Sodium Hypo-chloride after iron Removal Plant with electromagnetic metering pump run on 220 V AC for 100% accurate dosing with all accessories with 200 ltrs PVC tank- 2 Nos. (Necessary Civil work, foundation, PCC, RCC, excavation , returning and filling etc shall be deemed included in the quoted rate).- 01 Set Note :- (i) Minimum working pressure of the plant shall be - 2 Kgs/Sqcm Maximum working pressure of the plant shall be - 3.5Kgs/Sqcm (ii) Backwashing shall be 30 minutes at an interval of 8 hrs. (iii) Contractor has to carry out necessary raw water testing and design the plant accordingly to obtain portable water . Chemical / bacteriogical test of water has to be recorded and submitted by the contractor before & after filteration. (iv) All necessary pipes, flange, fittings, valves for bypass pipe line connection, and inter connetion the plant deemed to be included to the quoted rate. (v) Price of media for oxidation chamber and multigrade filter deemed to be inclusive of the quoted rate of the respective item. (vi) Suitable Demo by OEM rep be imparted to departmental staff for operation and price for the same deemed to be included in the quoted rate

Srl Item No. 68.00 Contd... treatment station with proportional dosing arrangement with following attachments: (i) Refill Cavity Lids (13) (ii) In-built Level Switch & Processor (iii) ½ inch Processor Outlet & Processor Inlet connections (iv) Flexible Connecting Duct Material of construction: Non-metallic, Maximum Temperature: 45°C,Shape: Circular (c) Additional Fittings: (i) 6 Mtr Suction Tubing (ii) PVC Ball Valve (iii) Plastic check valve (iv) Hose nipple Note :- M&L Necessary connections with pump distribution line shall deemed to be included in the quoted rate.

Srl Item No. 86.00 Contd... (C) TRANSFORMER (i) 1000 KVA, 11 kV/433 V, Dyn11, 3 phase, copper wound insulation class 'F', Natural Air Cooling Cast Resin Dry Type Transformer with off circuit link +5% to -5% @ 2.5 % on HT side of transformer with WTI scanner with Alarm and trip contact and other standard accessories - 01 No. (D) LT PANEL 3200 Amps rated copper bus bar for three phase and neutral with PVC sleeves supported on insulators - 04 Nos INCOMING :- (i) ACB, 2000 Amps, 50 kA, 4 pole, rated operational voltage 415-690 V, Manual draw out (MDO) type microprocessor release with LSIG protection unit with over current, short circuit and earth fault protection with LCD display with the manual setting nobs & current measurement on screen and battery back up with over temperature protection and indication for protection unit shunt trip, ove

r voltage & under voltage release, over frequency & under frequency, phase reversal, Terminals, dedicated slots for releases,In Built Temperature Protection, Ics=Icu=Icw rated impulse withstand voltage 12 kV - 01 No. OUTGOING :- (i) ACB FP, 1000 Amps rating, MDO type, Ics=100%Icu, 50 kA breaking capacity, adjustable thermal magnetic release - 01 No (ii) MCCB FP, 800 Amps rating, Ics=100%Icu, 50 kA breaking capacity, adjustable thermal magnetic release - 02 Nos. (01 Spare) (iii) MCCB FP, 400 Amps rating, Ics=100%Icu, 36 kA breaking capacity, adjustable thermal magnetic release - 03 Nos.(01 Spare) (iv) MCCB FP, 320 Amps rating, Ics=100%Icu, 36 kA breaking capacity, adjustable thermal magnetic release - 01 No.

Supply and fixing GI steel rope flexible 8 mm dia with GI clamps, nuts, bolts, washer etc for fixing of submersible pump set complete all as specified and directed.

PRIME COST SUM. The prime cost is to used as directed by the Accepting Officer vide condition 1(v) and 5 of IAFW-2249. (a) Provide a prime cost of Rs. 2,43,000.00 for Provision of 01 No. Coocking Platform as specified and approved by GE. (b) The contractor is to quote the amount in the money column i.e. in Col 'M' adding his overhead and profit. The amount shall be adjusted proportionately to the sum actually expended against Prime Cost Sum. Notes :- (i) Item(s) covered under Prime Cost Sum shall be ordered as per condition 5 of IAFW-2249. (ii) Contractor shall quote amount adding over the amount of prime cost sum to cover his overhead and profit. (iii) Percentage (plus/minus) subject to maximum of 15% (on plus side) shall be taken as the PC sum percentage.

PRIME COST SUM. The prime cost is to used as directed by the Accepting Officer vide condition 1(v) and 5 of IAFW-2249. (a) Provide a prime cost of Rs.1,03,600.00 for Provision of 02 Nos. Working Platform as specified and approved by GE. (b) The contractor is to quote the amount in the money column i.e. in Col 'M' adding his overhead and profit. The amount shall be adjusted proportionately to the sum actually expended against Prime Cost Sum. Notes :- (i) Item(s) covered under Prime Cost Sum shall be ordered as per condition 5 of IAFW-2249. (ii) Contractor shall quote amount adding over the amount of prime cost sum to cover his overhead and profit. (iii) Percentage (plus/minus) subject to maximum of 15% (on plus side) shall be taken as the PC sum percentage.

hick (45 Cm burried in ground) and properly painted as per approved colour Brown/Blue (HT/LT) and written both side with signed red colour paint ( MES HT cable 11/33 KV or LT cable 1100 Volts) on route marker including necessary excavation and earthwork complete all as specified and as directed. NOTE : (i) The spacing between two consecutive cable route indicators shall not be more than 50 meters & also shall be provided at each & every bend or corner. (ii) PCC for foundation will be measured and paid separately