Construction of shed along with table Tennis Court nearby the two Hostels i.e Natraj and shambu hostel at UHF Nauni solan SH Civil work

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas in all width and depth on plan) including getting out and disposal of excavated earth all leads, lifts and carriage of material as directed by the Engineer-in-charge .a). Ordinary rock

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete in all respect as per satisfaction of Engineer-in-charge.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth etc. complete in all respect as per satisfaction of Engineer-in-Charge..

Providing and laying in plain cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level etc. complete in all respect as per satisfaction of Engineer-in-Charge.

a). 1:5:10 (One cement : five sand : ten graded stone aggregate 40 mm ( forty milimetre nominal size).

b). 1:2:4 (one Cement: two sand : four graded stone aggregate 20 mm (twenty milimetre) nominal size.

Centering and shuttering including strutting, propping etc. and removal of form for etc. complete in all respect as per satisfaction of Engineer-in-charge a). Lintels, beams, plinth beams, girders, bressurmers and cantilevers.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, ifnishing and reinforcement work up to plinth level with 1.1.5:3 (one cement : one and half sand : three stone aggregate 20 mm (Twenty milimetre) nominal size) in foundation and plinth etc. Complete in all respect as per satisfaction of Engineer-in-charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Thermo-Mechanically Treated bars of grade Fe-500D or more. Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Thermo-Mechanically Treated bars of grade Fe-500D or more.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level with Cement mortar 1:4 (one cement : four sand) etc. complete in all respect as per satisfaction of Engineer-in-charge.

Brick edging 7 cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (one cement : four sand) complete in all respect as per satisfaction of Engineer-in-Charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length etc. complete in all respect as per satisfaction of Engineer-in-Charge. ( hold fast lugs or dash fastener shall be paid for separately. a).Sal wood

Providing and fixing 35 mm (Thirty five milimetre) thick Kiln seasoned and chemically treated hollock wood Glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing paneling or paneling and glazing shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick in 4 mm thick glass pane (weight not less than 10 kg per sqm) etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing wire gauge shutters Kiln seasoned and chemically treated hollock wood using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws with 35 mm (Thirty five milimetre) thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size etc. complete in all respect as per satisfaction of Engineer-in-charge..

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters etc. complete in all respect as per satisfaction of Engineer-in-Charge a). 30 mm ( Thirty milimetre) thick including ISI marked Stainless Steel butt hinges with necessary screws .

Providing and fixing ISI marked oxidized/ Chromium plated M.S. Sliding door bolts with nuts and screws etc. complete in all respect as per satisfaction of Engineer-in-Charge a). 250x16 mm ( Two hundred fifty into sixteen milimetre)

Providing and fixing ISI marked oxidized// Chromium plated M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge

a). 200x10 mm( Two hundred into ten milimetre)

b). 150x10 mm( One hundred fifty into ten milimetre)

Providing and fixing ISI marked oxidized/ chromium plated M.S. handles conforming to IS:4992 with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge

a). 125mm (one hundred twenty five milimetre)

b). 100mm (one hundred milimetre)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer etc. complete in all respect as per satisfaction of Engineer-in-Charge.

MS square/ rectangular hollow pipe welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using tube etc. as required. Complete in all respect as per satisfaction of Engineer-in-Charge. a).In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and laying rectified jointless Ceramic floor tiles (Kazaria / Oreint bell / Nitco/ Somany make) of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (one Cement : four sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing pre-coated galvanized steel sheet Ridges plain (500 - 600mm) 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete in all respect as per satisfaction of Engineer-in-Charge.(Tata/ Jindal/ISW make )

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. complete in all respect as per satisfaction of Engineer-in-Charge(Tata/ Jindal make).

Providing and fixing pre-coated galvanized iron profile/ linner sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.32 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during Transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. complete in all respect as per satisfaction of Engineer-in-Charge.(Tata/ Jindal /ISWMake)

15 mm (fifteen milimetre thick) cement plaster on rough side of single or half brick wall of mix with cement mortar 1:6 (one cement: six sand) complete in all respect as per satisfaction of Engineer-in-Charge.

Applying priming coat: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Two or more coats on new work.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade etc. all complete as specified and as directed by the Engineer-in-Charge a)Two or more coats on new work

Finishing walls with water proofing cement paint of required shade etc complete in all respect as per satisfaction of Engineer-in-Charge. a). New work (Two or more coats applied @ 3.84 kg/10 sqm)

Pawan Kumar (BID ID -565565)

shashikant (BID ID -562248)

PREM KRISHAN (BID ID -565588)