Maintenance work

Amount

Providing partition using double side teak wood sheet with melamine polishing with following specification. The frame using aluminium tubular section of size 50mm x 25mm x 2mm thick fixing horizontally and vertically in position with wall at interval of 0.60m in both directions, fixing water proof plywood of 12mm thick over the aluminium frame work with necessary screws. Both side teak wood sheet of 3.50mm thick will be fixed over the plywood using fevicol and finishing with melamine polishing and the rate inclusive of conveyance to site and labour charges and as directed by the Departmental Officers. The design pattern, water proof plywood, OST sheet and other materials to be used shall be got approved by the Executive Engineer concerned before use on work etc.,

Renewing and refixing the solid core flush door shutters with commercial ply on both side with teak wood lipping alround 35mm thick including cost of furniture fitting such as 3 nos 4"brass butt hinges,2nos 6"brass tower bolts,2nos 4"brass handle, 1 no brass drop, single key shutter, mortice lock without night latch, 1 no door closer, 1 no brass door stopper, 1mm thick best quality lamination sheet etc., complete complying with standard specification.

Renewing and refixing with new design ornamental sound proof armstrong grid false ceiling arrangements with Alu. anodized 'T' section and L angle frame work grid of size 60 x 60cm with Alu. T section 25 x 25 x 2.80mm L angle of size 25 x 25 x 2mm thick and the same is supported at suitable intervals by adjustable type 6mm dia M.S Rods with suitable threaded nuts, suspended rod and hanging from ceiling at 1.20m centre to centre in longitudinal section and 60cm at middle portion 60 x 60cm panel should be covered with 20mm thick armstrong sheet in grid so as to give neat finishing etc., complete with necessary openings for electrical fittings.

Repainting the old walls with thorough scraping and two coats of best Exterior emulsion Paint of approved colour and quality including preparation of surface. through scrapping and finishing neatly etc., complete complying with standard specification and as directed by the departmental officers. (The colour should be got approved by the Executive Engineer before use)

Providing the Roller blinds as per the following specification the fabrication colour and white of fabric vanes to have bottom packed the same materials as the vane stablishing weight is to be located in the shutter in plastering moulding to be but in the top side of bottom paacked as all fabric vanes to be sufficiently high quality materials were finished not tray one use in norml all the fabric is opened by rails manufacture from extruded aluminium powder coated in the standard colour rate inclusive of labour charges for fixing etc., complete complying with standard specification and as etc.,complete complying with standard specification and as directed by the departmental officers.

Renewing and refixing in position of SS Long body tap of approved quality make conforming to IS Specification and quality including cost of shellac, thread etc., complete complying with standard specification and as directed by the departmental officers.

Supplying new one of Health faucet of approved quality including cost of materials etc., complete and as directed by the departmental officers.

Supplying and fixing of Writing table/Dining table made up of prelaminated partical board with following accessories Table top are to be made of 25mm thick particle board finished with approved laminate and all exposed edges to be sealed with 2mm thick matching edge band and MS steel legs with 2-coats of iron paintings required screws including welding, cutting and labour charges of fixing in position neatly finishing ect., complete complying with standard specification and as directed by the departmental officers (The colour and quality of panels should be approved by the departmental officers before execution of work)

Dining table of size 2.10 x 0.60 x 0.75m

Dining table of size 2.10 x 0.60 x 0.45m

Supplying and fixing in wooden Rack of size 1800mm x 750mm x 2100mm(H) 5panels making 4 compartment including labour charges etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing in Steel slotted angle Rack of size 900mm x 450mm x 1800mm(H) - Angle of 16gauge with panels of 20gauge 5panels making 4 compartment including labour charges etc., complete complying with standard specifications and as directed by the departmental officers.

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing of Sun control flim is approved quality make and fixing in position, labour charges, conveyance etc., complete and as directed by the departmental officers.

GST at 18%

K SENTHIL KUMAR